[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.84+ (osstest@pinot0) (arm-linux-gnueabihf-gcc (Debian 8.3.0-2) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1 SMP Thu Apr 11 20:37:23 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.16 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 16 pages/cpu s35412 r8192 d21932 u65536 [ 0.000000] pcpu-alloc: s35412 r8192 d21932 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 net.ifnames=0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 418284K/524288K available (13312K kernel code, 2179K rwdata, 5632K rodata, 2048K init, 435K bss, 40468K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000012] Switching to timer-based delay loop, resolution 41ns [ 0.000501] Console: colour dummy device 80x30 [ 0.293579] printk: console [hvc0] enabled [ 0.297769] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.308171] CPU: Testing write buffer coherency: ok [ 0.313111] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.322683] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.329079] pid_max: default: 32768 minimum: 301 [ 0.333878] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.341147] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.349553] /cpus/cpu@0 missing clock-frequency property [ 0.354350] /cpus/cpu@1 missing clock-frequency property [ 0.359744] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.366269] xen:grant_table: Grant tables using version 1 layout [ 0.371587] Grant table initialized [ 0.375130] xen:events: Using FIFO-based ABI [ 0.379449] Xen: initializing cpu0 [ 0.382973] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.390759] rcu: Hierarchical SRCU implementation. [ 0.394368] rcu: Max phase no-delay instances is 1000. [ 0.402568] EFI services will not be available. [ 0.405871] smp: Bringing up secondary CPUs ... [ 0.480846] Xen: initializing cpu1 [ 0.480983] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481005] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.499857] smp: Brought up 1 node, 2 CPUs [ 0.503651] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.509957] CPU: All CPU(s) started in SVC mode. [ 0.515311] devtmpfs: initialized [ 0.527682] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.534165] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.543890] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.552051] pinctrl core: initialized pinctrl subsystem [ 0.558485] DMI not present or invalid. [ 0.561593] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.568959] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.577725] thermal_sys: Registered thermal governor 'step_wise' [ 0.578046] software IO TLB: area num 2. [ 0.586725] software IO TLB: only able to allocate 8 MB [ 0.593844] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.599026] No ATAGs? [ 0.601354] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.609885] Serial: AMBA PL011 UART driver [ 0.632013] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 62 [ 0.681399] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.705368] xen:balloon: Initialising balloon driver [ 0.713045] iommu: Default domain type: Translated [ 0.716546] iommu: DMA domain TLB invalidation policy: strict mode [ 0.723504] SCSI subsystem initialized [ 0.726865] libata version 3.00 loaded. [ 0.727056] usbcore: registered new interface driver usbfs [ 0.732310] usbcore: registered new interface driver hub [ 0.737685] usbcore: registered new device driver usb [ 0.744337] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.747958] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.754255] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.762699] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.771856] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.777351] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.782058] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.788288] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.793520] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.798292] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.804404] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.809587] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.814502] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.820537] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.826326] pps_core: LinuxPPS API ver. 1 registered [ 0.830745] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.839945] PTP clock support registered [ 0.844133] EDAC MC: Ver: 3.0.0 [ 0.850019] vgaarb: loaded [ 0.852187] clocksource: Switched to clocksource arch_sys_counter [ 0.864433] NET: Registered PF_INET protocol family [ 0.868078] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.876035] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.883667] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.891464] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.899305] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.906592] TCP: Hash tables configured (established 4096 bind 4096) [ 0.912958] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.919507] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.926638] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.939410] RPC: Registered named UNIX socket transport module. [ 0.943963] RPC: Registered udp transport module. [ 0.948718] RPC: Registered tcp transport module. [ 0.953503] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.960006] PCI: CLS 0 bytes, default 64 [ 0.965527] Initialise system trusted keyrings [ 0.968739] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.980099] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.985117] NFS: Registering the id_resolver key type [ 0.989698] Key type id_resolver registered [ 0.991132] Trying to unpack rootfs image as initramfs... [ 0.993965] Key type id_legacy registered [ 0.994087] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.010261] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.057100] Key type asymmetric registered [ 1.059825] Asymmetric key parser 'x509' registered [ 1.064935] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.072256] io scheduler mq-deadline registered [ 1.076837] io scheduler kyber registered [ 1.115838] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.194005] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.200207] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.233954] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.240153] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.262764] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.268962] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.303056] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.309253] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.323467] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.353316] xen:xen_evtchn: Event-channel device installed [ 1.490290] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.509533] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 113, base_baud = 0) is a S3C6400/10 [ 1.536402] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 114, base_baud = 0) is a S3C6400/10 [ 1.544511] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 115, base_baud = 0) is a S3C6400/10 [ 1.564830] SuperH (H)SCI(F) driver initialized [ 1.569075] STMicroelectronics ASC driver initialized [ 1.574452] STM32 USART driver initialized [ 1.601950] Freeing initrd memory: 11368K [ 1.612317] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.626630] brd: module loaded [ 1.632590] loop: module loaded [ 1.648198] Invalid max_queues (4), will use default max: 2. [ 1.674697] tun: Universal TUN/TAP device driver, 1.6 [ 1.678574] CAN device driver interface [ 1.683743] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.694331] xen_netfront: Initialising Xen virtual ethernet driver [ 1.699200] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.704816] usbcore: registered new interface driver pegasus [ 1.710532] usbcore: registered new interface driver asix [ 1.716006] usbcore: registered new interface driver ax88179_178a [ 1.722195] usbcore: registered new interface driver cdc_ether [ 1.728067] usbcore: registered new interface driver smsc75xx [ 1.733904] usbcore: registered new interface driver smsc95xx [ 1.739696] usbcore: registered new interface driver net1080 [ 1.745435] usbcore: registered new interface driver cdc_subset [ 1.751408] usbcore: registered new interface driver zaurus [ 1.757093] usbcore: registered new interface driver cdc_ncm [ 1.766427] usbcore: registered new interface driver usb-storage [ 1.801226] s5m-rtc s5m-rtc: registered as rtc0 [ 1.810044] s5m-rtc s5m-rtc: setting system clock to 2024-04-12T09:24:20 UTC (1712913860) [ 1.818780] i2c_dev: i2c /dev entries driver [ 1.829234] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed for psci_sys_poweroff [ 1.838935] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 1.850218] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 1.861080] device-mapper: uevent: version 1.0.3 [ 1.864589] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 1.873578] cpu cpu0: OPP table can't be empty [ 1.878538] failed to register cpuidle driver [ 1.881769] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.890121] sdhci: Secure Digital Host Controller Interface driver [ 1.895164] sdhci: Copyright(c) Pierre Ossman [ 1.903314] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.911062] ledtrig-cpu: registered to indicate activity on CPUs [ 1.917141] usbcore: registered new interface driver usbhid [ 1.921330] usbhid: USB HID core driver [ 1.932310] NET: Registered PF_INET6 protocol family [ 1.936990] Segment Routing with IPv6 [ 1.939665] In-situ OAM (IOAM) with IPv6 [ 1.943724] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.950064] NET: Registered PF_PACKET protocol family [ 1.954793] can: controller area network core [ 1.959198] NET: Registered PF_CAN protocol family [ 1.964057] can: raw protocol [ 1.967061] can: broadcast manager protocol [ 1.971316] can: netlink gateway - max_hops=1 [ 1.976003] Key type dns_resolver registered [ 1.980933] ThumbEE CPU extension supported. [ 1.984464] Registering SWP/SWPB emulation handler [ 1.989737] Loading compiled-in X.509 certificates [ 2.018003] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.024105] clk: Not disabling unused clocks [ 2.030763] Freeing unused kernel image (initmem) memory: 2048K [ 2.036833] Run /init as init process [ 2.039109] with arguments: [ 2.039115] /init [ 2.039121] with environment: [ 2.039125] HOME=/ [ 2.039130] TERM=linux [ 3.077508] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.089429] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.090090] phy phy-12130000.phy.7: phy_power_on was called before phy_init [ 3.096576] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.103376] exynos-ohci 12120000.usb: USB Host Controller [ 3.117717] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 3.140545] phy phy-12130000.phy.7: phy_power_on was called before phy_init [ 3.146195] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.151704] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 3.166882] Synopsys Designware Multimedia Card Interface Driver [ 3.178778] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.185068] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.192481] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.222446] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.228444] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.246191] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.288509] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.294255] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.303152] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.331558] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.336637] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.342789] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.348271] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.358060] mmc_host mmc0: card is polling. [ 3.362454] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.368500] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.374061] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.415046] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.423465] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.423859] hub 1-0:1.0: USB hub found [ 3.437504] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.443083] scsi host0: ahci-dwc [ 3.446728] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 [ 3.464450] hub 1-0:1.0: 3 ports detected [ 3.472223] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.481230] hub 2-0:1.0: USB hub found [ 3.484807] hub 2-0:1.0: 3 ports detected [ 3.496302] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.500673] rtc rtc1: invalid alarm value: 1900-01-31T00:00:00 [ 3.508609] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.515188] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 3.524070] mmc1: new high speed SDHC card at address aaaa [ 3.530189] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 3.556707] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.566168] mmc0: new DDR MMC card at address 0001 [ 3.570879] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 3.578679] mmcblk0: p1 p2 p3 p4 [ 3.583052] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 3.588721] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 3.595751] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 3.952238] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.957972] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 3.963858] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 3.971456] ata1.00: configured for UDMA/133 [ 3.975213] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 3.985058] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 3.991204] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 3.996598] sd 0:0:0:0: [sda] Write Protect is off [ 4.001385] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.001638] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.010651] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.029008] sda: sda1 sda2 < sda5 > [ 4.031805] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.047646] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 4.073379] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.080503] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.085598] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.142489] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 4.150967] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.157041] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.162285] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.170008] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.178823] hub 3-0:1.0: USB hub found [ 4.181515] hub 3-0:1.0: 1 port detected [ 4.186308] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.194382] hub 4-0:1.0: USB hub found [ 4.197299] hub 4-0:1.0: 1 port detected [ 4.319035] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.390900] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.499559] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.607677] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.715772] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.823855] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.931931] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.040025] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.148113] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.256192] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.664925] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 5.772665] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 6.380981] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 11.622152] random: crng init done [ 12.406125] process '/usr/bin/fstype' started with executable stack [ 12.779749] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 13.013765] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: disabled. [ 14.700297] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.705358] wm8994: probe of 3-001a failed with error -22 [ 15.200099] systemd-udevd[306]: Network interface NamePolicy= disabled on kernel command line, ignoring. [ 16.419249] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 16.429672] mc: Linux media interface: v0.10 [ 16.454631] s5p-secss 10830000.sss: s5p-sss driver registered [ 16.515885] videodev: Linux video capture interface: v2.00 [ 16.720401] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 16.732362] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 16.796035] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.804336] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.827771] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.835162] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.869160] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.883893] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 16.893013] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 16.930996] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 16.938128] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 16.966400] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 16.974498] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 16.979949] blk_print_req_error: 6 callbacks suppressed [ 16.979959] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.092249] usb3503 usb-hub: switched to HUB mode [ 17.095645] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 17.102067] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.212320] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.239946] systemd-udevd[320]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 17.240190] systemd-udevd[335]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 17.315854] systemd-udevd[335]: Process 'ifupdown-hotplug' failed with exit code 1. [ 17.322317] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.335860] systemd-udevd[320]: Process 'ifupdown-hotplug' failed with exit code 1. [ 17.405092] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 17.431707] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.442189] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 17.539805] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.647885] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.656978] hub 2-3:1.0: USB hub found [ 17.659808] hub 2-3:1.0: 3 ports detected [ 17.755995] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.855946] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.863619] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.872443] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.894268] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.901953] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.910715] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.992188] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 18.145547] hub 2-3.2:1.0: USB hub found [ 18.148657] hub 2-3.2:1.0: 4 ports detected [ 18.174280] usbcore: registered new device driver onboard-usb-hub [ 18.185711] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 18.293012] hub 2-3.2:1.0: USB hub found [ 18.293498] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 18.304663] hub 2-3.2:1.0: 4 ports detected [ 18.316588] hub 2-3.2:1.0: USB hub found [ 18.319576] hub 2-3.2:1.0: 4 ports detected [ 18.642182] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 18.795948] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.905374] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 19.453946] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 19.468193] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 19.478005] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 62:24:48:af:ad:bb [ 19.512561] systemd-udevd[317]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 19.522398] systemd-udevd[317]: Could not generate persistent MAC address for eth0: No such file or directory [ 19.713865] systemd-udevd[317]: Process 'ifupdown-hotplug' failed with exit code 1. [ 20.173550] EXT4-fs (dm-0): re-mounted. Quota mode: disabled. [ 22.242475] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 22.291147] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: disabled. [ 22.442241] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 23.227626] systemd-udevd[317]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 23.237456] systemd-udevd[317]: Could not generate persistent MAC address for xenbr0: No such file or directory [ 23.244177] xenbr0: port 1(eth0) entered blocking state [ 23.252638] xenbr0: port 1(eth0) entered disabled state [ 23.258026] device eth0 entered promiscuous mode [ 23.268936] systemd-udevd[317]: Process 'ifupdown-hotplug' failed with exit code 1. [ 23.269217] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode