[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.274 (osstest@himrod0) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 SMP Mon Apr 22 15:21:19 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on EXYNOS5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920 [ 0.000000] pcpu-alloc: s50636 r8192 d23092 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 412380K/524288K available (12288K kernel code, 1504K rwdata, 4764K rodata, 2048K init, 405K bss, 46372K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000015] Switching to timer-based delay loop, resolution 41ns [ 0.000419] Console: colour dummy device 80x30 [ 0.244799] printk: console [hvc0] enabled [ 0.248986] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.259389] CPU: Testing write buffer coherency: ok [ 0.264333] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.273886] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.280300] pid_max: default: 32768 minimum: 301 [ 0.285074] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.292369] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.300809] /cpus/cpu@0 missing clock-frequency property [ 0.305570] /cpus/cpu@1 missing clock-frequency property [ 0.310964] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.318168] xen:grant_table: Grant tables using version 1 layout [ 0.322840] Grant table initialized [ 0.326426] xen:events: Using FIFO-based ABI [ 0.330719] Xen: initializing cpu0 [ 0.334245] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.341968] rcu: Hierarchical SRCU implementation. [ 0.348103] EFI services will not be available. [ 0.351374] smp: Bringing up secondary CPUs ... [ 1.392430] CPU1: failed to come online [ 1.418881] smp: Brought up 1 node, 1 CPU [ 1.446338] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 1.491606] CPU: All CPU(s) started in SVC mode. [ 1.528223] devtmpfs: initialized [ 1.569526] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 1.616993] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 1.689175] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 1.736296] pinctrl core: initialized pinctrl subsystem [ 1.773665] DMI not present or invalid. [ 1.799582] NET: Registered protocol family 16 [ 1.837555] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.884978] xen:swiotlb_xen: Warning: only able to allocate 8 MB for software IO TLB [ 1.937358] software IO TLB: mapped [mem 0x7a000000-0x7a800000] (8MB) [ 1.981134] No ATAGs? [ 1.981298] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 2.046740] Serial: AMBA PL011 UART driver [ 2.098081] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 71 [ 2.207123] xen:balloon: Initialising balloon driver [ 2.245944] iommu: Default domain type: Translated [ 2.277445] vgaarb: loaded [ 2.296265] SCSI subsystem initialized [ 2.322720] libata version 3.00 loaded. [ 2.322997] usbcore: registered new interface driver usbfs [ 2.359430] usbcore: registered new interface driver hub [ 2.396015] usbcore: registered new device driver usb [ 2.433928] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.468639] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.553880] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.589394] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.625485] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.670783] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.707185] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 2.743272] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 2.788564] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 2.824899] s3c-i2c 121d0000.i2c: slave address 0x38 [ 2.861058] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 2.906215] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 2.943288] pps_core: LinuxPPS API ver. 1 registered [ 2.978841] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.042741] PTP clock support registered [ 3.070429] EDAC MC: Ver: 3.0.0 [ 3.099868] clocksource: Switched to clocksource arch_sys_counter [ 3.614814] thermal_sys: Registered thermal governor 'step_wise' [ 3.615018] OF: /thermal-zones/cpu-thermal/cooling-maps/map0: could not find phandle [ 3.710603] thermal_sys: Add a cooling_device property with at least one device [ 3.764847] thermal_sys: failed to build thermal zone cpu-thermal: -2 [ 3.810554] NET: Registered protocol family 2 [ 3.846199] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 3.900833] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 3.955569] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 4.010273] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 4.064364] TCP: Hash tables configured (established 4096 bind 4096) [ 4.109862] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 4.155455] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 4.201670] NET: Registered protocol family 1 [ 4.237693] RPC: Registered named UNIX socket transport module. [ 4.282278] RPC: Registered udp transport module. [ 4.318266] RPC: Registered tcp transport module. [ 4.354299] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.399882] PCI: CLS 0 bytes, default 64 [ 4.427812] Trying to unpack rootfs image as initramfs... [ 5.395024] Freeing initrd memory: 20008K [ 5.422684] Initialise system trusted keyrings [ 5.457131] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 5.512198] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 5.556036] NFS: Registering the id_resolver key type [ 5.591711] Key type id_resolver registered [ 5.619306] Key type id_legacy registered [ 5.647080] Key type asymmetric registered [ 5.674440] Asymmetric key parser 'x509' registered [ 5.710667] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 5.764983] io scheduler mq-deadline registered [ 5.800821] io scheduler kyber registered [ 5.869424] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 5.913262] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 5.971156] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 6.014371] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 6.070582] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 6.115487] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 6.171579] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-241330 [ 6.216500] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 6.277495] xen:xen_evtchn: Event-channel device installed [ 6.367619] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.413267] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 53, base_baud = 0) is a S3C6400/10 [ 6.472838] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 54, base_baud = 0) is a S3C6400/10 [ 6.536371] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 55, base_baud = 0) is a S3C6400/10 [ 6.600272] SuperH (H)SCI(F) driver initialized [ 6.636835] STMicroelectronics ASC driver initialized [ 6.673581] STM32 USART driver initialized [ 6.709921] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 6.764299] brd: module loaded [ 6.795314] loop: module loaded [ 6.841144] Invalid max_queues (4), will use default max: 1. [ 6.885345] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 6.937667] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 7.006647] tun: Universal TUN/TAP device driver, 1.6 [ 7.037067] CAN device driver interface [ 7.065572] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 7.116472] xen_netfront: Initialising Xen virtual ethernet driver [ 7.154403] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 7.208677] usbcore: registered new interface driver pegasus [ 7.253475] usbcore: registered new interface driver asix [ 7.290177] usbcore: registered new interface driver ax88179_178a [ 7.335398] usbcore: registered new interface driver cdc_ether [ 7.380388] usbcore: registered new interface driver smsc75xx [ 7.425248] usbcore: registered new interface driver smsc95xx [ 7.470117] usbcore: registered new interface driver net1080 [ 7.514901] usbcore: registered new interface driver cdc_subset [ 7.559954] usbcore: registered new interface driver zaurus [ 7.596840] usbcore: registered new interface driver cdc_ncm [ 7.642915] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.687228] ehci-pci: EHCI PCI platform driver [ 7.723048] ehci-platform: EHCI generic platform driver [ 7.759859] ehci-orion: EHCI orion driver [ 7.787277] SPEAr-ehci: EHCI SPEAr driver [ 7.814789] ehci-st: EHCI STMicroelectronics driver [ 7.850994] ehci-atmel: EHCI Atmel driver [ 7.878485] tegra-ehci: Tegra EHCI driver [ 7.906052] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.951150] ohci-pci: OHCI PCI platform driver [ 7.986888] ohci-platform: OHCI generic platform driver [ 8.023678] SPEAr-ohci: OHCI SPEAr driver [ 8.051144] ohci-st: OHCI STMicroelectronics driver [ 8.087323] ohci-atmel: OHCI Atmel driver [ 8.115643] usbcore: registered new interface driver usb-storage [ 8.220404] s5m-rtc s5m-rtc: registered as rtc0 [ 8.262220] i2c /dev entries driver [ 8.295151] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff [ 8.374840] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 8.441310] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 8.484533] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 8.536527] device-mapper: uevent: version 1.0.3 [ 8.566048] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 8.630283] cpu cpu0: failed to get clock: -2 [ 8.664620] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 8.711899] failed to register cpuidle driver [ 8.745420] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 8.800113] sdhci: Secure Digital Host Controller Interface driver [ 8.844723] sdhci: Copyright(c) Pierre Ossman [ 8.884512] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.929158] ledtrig-cpu: registered to indicate activity on CPUs [ 8.971331] usbcore: registered new interface driver usbhid [ 9.007186] usbhid: USB HID core driver [ 9.039777] drop_monitor: Initializing network drop monitor service [ 9.080872] NET: Registered protocol family 10 [ 9.116400] Segment Routing with IPv6 [ 9.142952] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 9.188522] NET: Registered protocol family 17 [ 9.223731] can: controller area network core (rev 20170425 abi 9) [ 9.269060] NET: Registered protocol family 29 [ 9.304766] can: raw protocol (rev 20170425) [ 9.340355] can: broadcast manager protocol (rev 20170425 t) [ 9.385157] can: netlink gateway (rev 20190810) max_hops=1 [ 9.422331] Key type dns_resolver registered [ 9.457970] ThumbEE CPU extension supported. [ 9.493131] Registering SWP/SWPB emulation handler [ 9.529609] Loading compiled-in X.509 certificates [ 9.609013] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 9.659736] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 9.717054] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 9.760441] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 9.806900] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 9.861025] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 9.918217] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 9.961702] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 10.009164] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 10.054333] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 10.108135] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 10.165443] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 10.208820] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 10.259975] s5m-rtc s5m-rtc: setting system clock to 2024-04-22T20:09:21 UTC (1713816561) [ 10.309429] clk: Not disabling unused clocks [ 10.348620] Freeing unused kernel memory: 2048K [ 10.381993] Run /init as init process [ 12.504655] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator [ 12.564613] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator [ 12.652270] Synopsys Designware Multimedia Card Interface Driver [ 12.699796] ohci-exynos: OHCI EXYNOS driver [ 12.732561] ehci-exynos: EHCI EXYNOS driver [ 12.756650] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator [ 12.817986] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.872340] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 12.926110] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 12.981223] ahci 122f0000.sata: 122f0000.sata supply target not found, using dummy regulator [ 13.112455] s2mps11-clk s5m8767-clk: DMA mask not set [ 13.189406] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 13.383672] wm8994: probe of 3-001a failed with error -22 [ 13.438271] gpio-6 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 13.499862] gpio-7 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 13.567734] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd33 not found, using dummy regulator [ 13.627750] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd10 not found, using dummy regulator [ 13.852644] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 13.892978] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 13.929741] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 100,32 bit host data width,128 deep fifo [ 13.994123] mmc_host mmc0: card is polling. [ 14.200026] debugfs: Directory 'VDD_33ON_2.8V' with parent 'regulator' already present! [ 14.510053] ahci 122f0000.sata: SSS flag set, parallel bus scan disabled [ 14.552023] ahci 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 14.615296] ahci 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 14.715477] i2c-gpio soc:i2c-gpio: using lines 6 (SDA) and 7 (SCL) [ 15.010340] dwc3 12000000.dwc3: Failed to get clk 'ref': -2 [ 15.072689] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.132680] dwc3 12000000.dwc3: Configuration mismatch. dr_mode forced to host [ 15.185187] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.220908] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1 [ 15.277471] scsi host0: ahci [ 15.302341] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 98 [ 15.358288] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.402417] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 15.447727] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 15.499621] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 15.539314] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 15.576095] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 101,32 bit host data width,128 deep fifo [ 15.641203] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 15.704529] xhci-hcd xhci-hcd.2.auto: irq 146, io mem 0x12000000 [ 15.749811] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.786314] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2 [ 15.840917] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 15.886642] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 15.924695] s3c-rtc 101e0000.rtc: registered as rtc1 [ 15.961874] exynos-ohci 12120000.usb: USB Host Controller [ 15.999687] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.061983] hub 1-0:1.0: USB hub found [ 16.090307] hub 1-0:1.0: 1 port detected [ 16.116617] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 16.171800] hub 2-0:1.0: USB hub found [ 16.197957] hub 2-0:1.0: 1 port detected [ 16.227305] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 3 [ 16.279923] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 16.326253] exynos-ohci 12120000.usb: irq 102, io mem 0x12120000 [ 16.370174] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 16.415943] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 16.468630] hub 3-0:1.0: USB hub found [ 16.489223] hub 3-0:1.0: 3 ports detected [ 16.519078] exynos-ehci 12110000.usb: EHCI Host Controller [ 16.553245] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 4 [ 16.610128] ata1.00: configured for UDMA/133 [ 16.643889] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 16.712490] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 16.773868] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 16.825170] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 16.865884] mmc0: new DDR MMC card at address 0001 [ 16.898630] exynos-ehci 12110000.usb: irq 102, io mem 0x12110000 [ 16.943372] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 16.979067] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB [ 17.024097] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB [ 17.069078] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 17.114062] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.178566] sd 0:0:0:0: [sda] Write Protect is off [ 17.214592] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 17.214716] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 17.280688] hub 4-0:1.0: USB hub found [ 17.306008] mmc1: new high speed SDHC card at address aaaa [ 17.342937] hub 4-0:1.0: 3 ports detected [ 17.370065] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB, chardev (237:0) [ 17.426567] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.469857] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.522018] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 17.561106] mmcblk0: p1 p2 p3 p4 [ 17.590009] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.631178] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.679440] sda: sda1 sda2 < sda5 > [ 17.711301] sd 0:0:0:0: [sda] Attached SCSI disk [ 17.867600] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.910221] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 18.026293] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 18.071514] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 18.288755] random: lvm: uninitialized urandom read (4 bytes read) [ 18.448595] random: lvm: uninitialized urandom read (4 bytes read) [ 18.506789] random: lvm: uninitialized urandom read (2 bytes read) [ 22.545209] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 22.850604] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 27.798764] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 27.838096] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 27.901195] mc: Linux media interface: v0.10 [ 27.962133] s5p-secss 10830000.sss: s5p-sss driver registered [ 28.399721] videodev: Linux video capture interface: v2.00 [ 28.634189] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 28.675609] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 28.834390] s5p-mfc 11000000.codec: ignoring dependency for device, assuming no driver [ 28.911729] exynos-gsc 13e00000.gsc: ignoring dependency for device, assuming no driver [ 29.020050] usb3503 usb-hub: switched to HUB mode [ 29.054160] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 29.139761] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 29.183888] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 29.240354] exynos-gsc 13e10000.gsc: ignoring dependency for device, assuming no driver [ 29.300787] exynos-gsc 13e20000.gsc: ignoring dependency for device, assuming no driver [ 29.377937] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 29.415992] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 29.471733] exynos-gsc 13e30000.gsc: ignoring dependency for device, assuming no driver [ 29.538091] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 29.577551] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 29.740485] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 30.022619] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 30.066992] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 30.173031] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 30.409984] usb 4-3: new high-speed USB device number 2 using exynos-ehci [ 30.714500] random: lvm: uninitialized urandom read (4 bytes read) [ 30.981579] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 31.092663] hub 4-3:1.0: USB hub found [ 31.319248] hub 4-3:1.0: 3 ports detected [ 31.460297] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 31.519503] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 31.605287] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 31.645914] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 31.725583] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 31.768778] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 31.817186] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 31.859217] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 31.937218] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 31.999471] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 32.062891] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 32.150004] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 32.207458] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 32.270875] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 32.409927] usb 4-3.2: new high-speed USB device number 3 using exynos-ehci [ 32.654328] hub 4-3.2:1.0: USB hub found [ 32.680154] hub 4-3.2:1.0: 4 ports detected [ 32.711200] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 32.749418] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 33.019946] usb 4-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 33.067396] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 33.264813] asix 4-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 33.901100] asix 4-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 02:2c:32:ff:d3:ab [ 34.082668] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 34.126030] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 35.053494] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 35.161082] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 35.309506] random: crng init done [ 35.346636] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 37.460475] xenbr0: port 1(eth0) entered blocking state [ 37.494000] xenbr0: port 1(eth0) entered disabled state [ 37.530856] device eth0 entered promiscuous mode [ 37.820577] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 37.890472] asix 4-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 [ 38.000482] xenbr0: port 1(eth0) entered blocking state [ 38.030527] xenbr0: port 1(eth0) entered forwarding state [ 38.067983] IPv6: ADDRCONF(NETDEV_CHANGE): xenbr0: link becomes ready [ 40.819966] MAIN_DC: disabling [ 40.842557] hdmi-en: disabling [ 40.869150] VCC_1V2: disabling [ 40.895706] VCC_1V8: disabling [ 40.922269] VCC_3V3: disabling