[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.274 (osstest@himrod0) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 SMP Mon Apr 22 15:21:19 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on EXYNOS5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920 [ 0.000000] pcpu-alloc: s50636 r8192 d23092 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 412380K/524288K available (12288K kernel code, 1504K rwdata, 4764K rodata, 2048K init, 405K bss, 46372K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000015] Switching to timer-based delay loop, resolution 41ns [ 0.000420] Console: colour dummy device 80x30 [ 0.245318] printk: console [hvc0] enabled [ 0.249505] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.259907] CPU: Testing write buffer coherency: ok [ 0.264852] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.274405] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.280819] pid_max: default: 32768 minimum: 301 [ 0.285591] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.292887] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.301324] /cpus/cpu@0 missing clock-frequency property [ 0.306113] /cpus/cpu@1 missing clock-frequency property [ 0.311484] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.318687] xen:grant_table: Grant tables using version 1 layout [ 0.323357] Grant table initialized [ 0.326921] xen:events: Using FIFO-based ABI [ 0.331236] Xen: initializing cpu0 [ 0.334764] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.342487] rcu: Hierarchical SRCU implementation. [ 0.348620] EFI services will not be available. [ 0.351893] smp: Bringing up secondary CPUs ... [ 1.393032] CPU1: failed to come online [ 1.419263] smp: Brought up 1 node, 1 CPU [ 1.446715] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 1.491985] CPU: All CPU(s) started in SVC mode. [ 1.528601] devtmpfs: initialized [ 1.569971] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 1.617379] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 1.689558] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 1.736671] pinctrl core: initialized pinctrl subsystem [ 1.774051] DMI not present or invalid. [ 1.799961] NET: Registered protocol family 16 [ 1.837941] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.885364] xen:swiotlb_xen: Warning: only able to allocate 8 MB for software IO TLB [ 1.937731] software IO TLB: mapped [mem 0x7a000000-0x7a800000] (8MB) [ 1.981512] No ATAGs? [ 1.981676] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 2.047112] Serial: AMBA PL011 UART driver [ 2.098477] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 71 [ 2.207823] xen:balloon: Initialising balloon driver [ 2.246538] iommu: Default domain type: Translated [ 2.277618] vgaarb: loaded [ 2.296663] SCSI subsystem initialized [ 2.323103] libata version 3.00 loaded. [ 2.323382] usbcore: registered new interface driver usbfs [ 2.359783] usbcore: registered new interface driver hub [ 2.396396] usbcore: registered new device driver usb [ 2.434325] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.469022] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.554256] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.589778] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.625864] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.671167] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.707574] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 2.743652] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 2.788943] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 2.825279] s3c-i2c 121d0000.i2c: slave address 0x38 [ 2.861440] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 2.906600] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 2.943673] pps_core: LinuxPPS API ver. 1 registered [ 2.979221] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.043120] PTP clock support registered [ 3.070813] EDAC MC: Ver: 3.0.0 [ 3.100270] clocksource: Switched to clocksource arch_sys_counter [ 3.615600] thermal_sys: Registered thermal governor 'step_wise' [ 3.615798] OF: /thermal-zones/cpu-thermal/cooling-maps/map0: could not find phandle [ 3.710982] thermal_sys: Add a cooling_device property with at least one device [ 3.765228] thermal_sys: failed to build thermal zone cpu-thermal: -2 [ 3.810936] NET: Registered protocol family 2 [ 3.846580] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 3.901215] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 3.955950] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 4.010654] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 4.064743] TCP: Hash tables configured (established 4096 bind 4096) [ 4.110213] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 4.155845] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 4.202049] NET: Registered protocol family 1 [ 4.238077] RPC: Registered named UNIX socket transport module. [ 4.282662] RPC: Registered udp transport module. [ 4.318647] RPC: Registered tcp transport module. [ 4.354680] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.400265] PCI: CLS 0 bytes, default 64 [ 4.428195] Trying to unpack rootfs image as initramfs... [ 5.395977] Freeing initrd memory: 20008K [ 5.423085] Initialise system trusted keyrings [ 5.457540] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 5.512652] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 5.556415] NFS: Registering the id_resolver key type [ 5.592061] Key type id_resolver registered [ 5.619685] Key type id_legacy registered [ 5.647466] Key type asymmetric registered [ 5.674820] Asymmetric key parser 'x509' registered [ 5.711045] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 5.765365] io scheduler mq-deadline registered [ 5.801202] io scheduler kyber registered [ 5.870305] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 5.913617] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 5.971536] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 6.014750] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 6.070964] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 6.115867] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 6.171954] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-241330 [ 6.216903] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 6.277944] xen:xen_evtchn: Event-channel device installed [ 6.368320] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.413669] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 53, base_baud = 0) is a S3C6400/10 [ 6.473213] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 54, base_baud = 0) is a S3C6400/10 [ 6.536774] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 55, base_baud = 0) is a S3C6400/10 [ 6.600648] SuperH (H)SCI(F) driver initialized [ 6.637228] STMicroelectronics ASC driver initialized [ 6.673979] STM32 USART driver initialized [ 6.710327] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 6.764752] brd: module loaded [ 6.795732] loop: module loaded [ 6.841619] Invalid max_queues (4), will use default max: 1. [ 6.885743] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 6.938056] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 7.007192] tun: Universal TUN/TAP device driver, 1.6 [ 7.037454] CAN device driver interface [ 7.065963] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 7.116920] xen_netfront: Initialising Xen virtual ethernet driver [ 7.154784] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 7.209058] usbcore: registered new interface driver pegasus [ 7.253856] usbcore: registered new interface driver asix [ 7.290556] usbcore: registered new interface driver ax88179_178a [ 7.335779] usbcore: registered new interface driver cdc_ether [ 7.380768] usbcore: registered new interface driver smsc75xx [ 7.425630] usbcore: registered new interface driver smsc95xx [ 7.470498] usbcore: registered new interface driver net1080 [ 7.515283] usbcore: registered new interface driver cdc_subset [ 7.560334] usbcore: registered new interface driver zaurus [ 7.597241] usbcore: registered new interface driver cdc_ncm [ 7.643308] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.687608] ehci-pci: EHCI PCI platform driver [ 7.723430] ehci-platform: EHCI generic platform driver [ 7.760215] ehci-orion: EHCI orion driver [ 7.787669] SPEAr-ehci: EHCI SPEAr driver [ 7.815170] ehci-st: EHCI STMicroelectronics driver [ 7.851378] ehci-atmel: EHCI Atmel driver [ 7.878873] tegra-ehci: Tegra EHCI driver [ 7.906436] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.951531] ohci-pci: OHCI PCI platform driver [ 7.987269] ohci-platform: OHCI generic platform driver [ 8.024064] SPEAr-ohci: OHCI SPEAr driver [ 8.051529] ohci-st: OHCI STMicroelectronics driver [ 8.087705] ohci-atmel: OHCI Atmel driver [ 8.116034] usbcore: registered new interface driver usb-storage [ 8.240807] s5m-rtc s5m-rtc: registered as rtc0 [ 8.282629] i2c /dev entries driver [ 8.319133] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff [ 8.398663] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 8.465138] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 8.508325] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 8.560487] device-mapper: uevent: version 1.0.3 [ 8.589851] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 8.654083] cpu cpu0: failed to get clock: -2 [ 8.688418] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 8.735723] failed to register cpuidle driver [ 8.769237] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 8.823914] sdhci: Secure Digital Host Controller Interface driver [ 8.868547] sdhci: Copyright(c) Pierre Ossman [ 8.908407] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.953011] ledtrig-cpu: registered to indicate activity on CPUs [ 8.995151] usbcore: registered new interface driver usbhid [ 9.031032] usbhid: USB HID core driver [ 9.063656] drop_monitor: Initializing network drop monitor service [ 9.104686] NET: Registered protocol family 10 [ 9.140300] Segment Routing with IPv6 [ 9.166743] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 9.212348] NET: Registered protocol family 17 [ 9.247516] can: controller area network core (rev 20170425 abi 9) [ 9.292884] NET: Registered protocol family 29 [ 9.328576] can: raw protocol (rev 20170425) [ 9.364172] can: broadcast manager protocol (rev 20170425 t) [ 9.408973] can: netlink gateway (rev 20190810) max_hops=1 [ 9.446144] Key type dns_resolver registered [ 9.481798] ThumbEE CPU extension supported. [ 9.516914] Registering SWP/SWPB emulation handler [ 9.553433] Loading compiled-in X.509 certificates [ 9.633094] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 9.683552] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 9.740955] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 9.784231] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 9.830780] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 9.884822] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 9.942068] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 9.985483] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 10.032993] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 10.078228] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 10.131963] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 10.189337] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 10.232643] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 10.277992] s5m-rtc s5m-rtc: setting system clock to 2000-01-02T00:00:35 UTC (946771235) [ 10.333160] clk: Not disabling unused clocks [ 10.372610] Freeing unused kernel memory: 2048K [ 10.405685] Run /init as init process [ 12.536608] ehci-exynos: EHCI EXYNOS driver [ 12.566959] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator [ 12.623832] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator [ 12.714160] Synopsys Designware Multimedia Card Interface Driver [ 12.759729] ohci-exynos: OHCI EXYNOS driver [ 12.788317] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator [ 12.881612] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.963795] s2mps11-clk s5m8767-clk: DMA mask not set [ 13.041433] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 13.092488] VDD_ALIVE_1.0V: Bringing 1000000uV into 1100000-1100000uV [ 13.290184] wm8994: probe of 3-001a failed with error -22 [ 13.324758] gpio-6 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 13.387783] gpio-7 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 13.469592] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 13.523002] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 13.578100] ahci 122f0000.sata: 122f0000.sata supply target not found, using dummy regulator [ 13.738002] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd33 not found, using dummy regulator [ 13.798576] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd10 not found, using dummy regulator [ 13.960479] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 14.001334] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 14.038100] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 100,32 bit host data width,128 deep fifo [ 14.102495] mmc_host mmc0: card is polling. [ 14.330427] debugfs: Directory 'VDD_33ON_2.8V' with parent 'regulator' already present! [ 14.616773] i2c-gpio soc:i2c-gpio: using lines 6 (SDA) and 7 (SCL) [ 14.950351] dwc3 12000000.dwc3: Failed to get clk 'ref': -2 [ 14.995726] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.058023] dwc3 12000000.dwc3: Configuration mismatch. dr_mode forced to host [ 15.113103] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.148799] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1 [ 15.205490] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 15.267685] xhci-hcd xhci-hcd.2.auto: irq 146, io mem 0x12000000 [ 15.312978] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.349463] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2 [ 15.404082] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 15.449853] ahci 122f0000.sata: SSS flag set, parallel bus scan disabled [ 15.495610] ahci 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 15.558841] ahci 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 15.622425] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 15.671154] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 15.713975] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 15.750744] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 101,32 bit host data width,128 deep fifo [ 15.815773] scsi host0: ahci [ 15.841735] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 98 [ 15.897686] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.941829] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 15.992083] hub 1-0:1.0: USB hub found [ 16.014703] hub 1-0:1.0: 1 port detected [ 16.042935] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 16.098057] hub 2-0:1.0: USB hub found [ 16.124407] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.188410] hub 2-0:1.0: 1 port detected [ 16.222650] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 16.253819] s3c-rtc 101e0000.rtc: registered as rtc1 [ 16.291085] exynos-ehci 12110000.usb: EHCI Host Controller [ 16.325735] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 3 [ 16.384039] exynos-ehci 12110000.usb: irq 102, io mem 0x12110000 [ 16.450322] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 16.496671] hub 3-0:1.0: USB hub found [ 16.521649] hub 3-0:1.0: 3 ports detected [ 16.551477] exynos-ohci 12120000.usb: USB Host Controller [ 16.585559] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 4 [ 16.643113] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 16.687225] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 16.763814] mmc0: new DDR MMC card at address 0001 [ 16.794125] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 16.839648] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 16.885337] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.950593] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 16.985926] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB [ 17.030997] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB [ 17.076386] exynos-ohci 12120000.usb: irq 102, io mem 0x12120000 [ 17.120914] mmc1: new high speed SDHC card at address aaaa [ 17.158500] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 17.197689] ata1.00: configured for UDMA/133 [ 17.229282] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 17.286350] hub 4-0:1.0: USB hub found [ 17.311641] hub 4-0:1.0: 3 ports detected [ 17.344315] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 17.393307] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 17.435068] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.475524] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.530374] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB, chardev (237:0) [ 17.584709] sd 0:0:0:0: [sda] Write Protect is off [ 17.618879] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 17.621446] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 17.682814] mmcblk0: p1 p2 p3 p4 [ 17.722245] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.763032] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.808345] sda: sda1 sda2 < sda5 > [ 17.842070] sd 0:0:0:0: [sda] Attached SCSI disk [ 17.987970] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 18.026347] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 18.372030] random: lvm: uninitialized urandom read (4 bytes read) [ 18.509828] random: lvm: uninitialized urandom read (4 bytes read) [ 18.570967] random: lvm: uninitialized urandom read (2 bytes read) [ 18.860352] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 19.037640] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 19.441574] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 19.847179] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 20.248970] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 20.650772] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 21.052562] blk_update_request: I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 21.468372] blk_update_request: I/O error, dev mmcblk1, sector 7744007 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 21.871783] blk_update_request: I/O error, dev mmcblk1, sector 7744008 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 0 [ 22.307019] blk_update_request: I/O error, dev mmcblk1, sector 7744016 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 22.714411] blk_update_request: I/O error, dev mmcblk1, sector 7744017 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 23.116239] blk_update_request: I/O error, dev mmcblk1, sector 7744018 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 24.552300] print_req_error: 3 callbacks suppressed [ 24.552308] blk_update_request: I/O error, dev mmcblk1, sector 7744025 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 24.995017] blk_update_request: I/O error, dev mmcblk1, sector 7744026 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 25.396814] blk_update_request: I/O error, dev mmcblk1, sector 7744027 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 26.240330] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 26.417496] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 26.810189] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.211456] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.612810] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 28.014160] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 28.111601] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 31.909484] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 32.333391] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 37.495453] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 37.540974] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 37.604083] mc: Linux media interface: v0.10 [ 37.681613] s5p-secss 10830000.sss: s5p-sss driver registered [ 38.127449] videodev: Linux video capture interface: v2.00 [ 38.297250] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 38.339345] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 38.782640] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 38.846802] s5p-mfc 11000000.codec: ignoring dependency for device, assuming no driver [ 38.910424] usb3503 usb-hub: switched to HUB mode [ 38.945943] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 38.993579] exynos-gsc 13e00000.gsc: ignoring dependency for device, assuming no driver [ 39.099706] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 39.138345] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 39.186164] exynos-gsc 13e10000.gsc: ignoring dependency for device, assuming no driver [ 39.239059] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 39.310217] exynos-gsc 13e20000.gsc: ignoring dependency for device, assuming no driver [ 39.370563] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 39.411545] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 39.458522] exynos-gsc 13e30000.gsc: ignoring dependency for device, assuming no driver [ 39.525362] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 39.565313] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 39.639947] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 39.748966] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 39.792582] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 39.867047] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 40.029671] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 40.070993] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 40.116724] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 40.219604] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 40.360371] usb 3-3: new high-speed USB device number 2 using exynos-ehci [ 40.525667] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 40.820358] MAIN_DC: disabling [ 40.845048] hdmi-en: disabling [ 40.871604] VCC_1V2: disabling [ 40.898134] VCC_1V8: disabling [ 40.924726] VCC_3V3: disabling [ 40.951670] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 41.141505] hub 3-3:1.0: USB hub found [ 41.161678] random: crng init done [ 41.220747] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 41.390774] blk_update_request: I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 41.729047] hub 3-3:1.0: 3 ports detected [ 41.807862] blk_update_request: I/O error, dev mmcblk1, sector 7744008 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 0 [ 41.942866] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 42.006293] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 42.081482] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 42.126003] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 42.174140] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 42.216046] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 42.261479] blk_update_request: I/O error, dev mmcblk1, sector 7744013 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 0 [ 42.362039] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 42.404115] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 42.449502] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 42.513155] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 42.576557] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 42.680409] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 42.736841] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 42.800168] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 42.873332] blk_update_request: I/O error, dev mmcblk1, sector 7744015 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 0 [ 43.050309] usb 3-3.2: new high-speed USB device number 3 using exynos-ehci [ 43.253993] hub 3-3.2:1.0: USB hub found [ 43.278504] hub 3-3.2:1.0: 4 ports detected [ 43.305967] blk_update_request: I/O error, dev mmcblk1, sector 7744016 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 43.385324] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 43.425240] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 43.710309] usb 3-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 43.759042] blk_update_request: I/O error, dev mmcblk1, sector 7744017 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 43.985134] asix 3-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 44.571542] asix 3-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 82:ea:50:c8:ee:b7 [ 44.660039] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 44.703611] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 44.839831] print_req_error: 2 callbacks suppressed [ 44.839842] blk_update_request: I/O error, dev mmcblk1, sector 7744020 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 45.280393] blk_update_request: I/O error, dev mmcblk1, sector 7744021 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 45.695061] blk_update_request: I/O error, dev mmcblk1, sector 7744023 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 46.099575] blk_update_request: I/O error, dev mmcblk1, sector 7744024 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 46.501376] blk_update_request: I/O error, dev mmcblk1, sector 7744025 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 46.903156] blk_update_request: I/O error, dev mmcblk1, sector 7744026 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 47.304960] blk_update_request: I/O error, dev mmcblk1, sector 7744027 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 48.860331] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 49.037904] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 49.437029] blk_update_request: I/O error, dev mmcblk1, sector 7744016 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 49.838281] blk_update_request: I/O error, dev mmcblk1, sector 7744017 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.239678] blk_update_request: I/O error, dev mmcblk1, sector 7744018 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.641035] blk_update_request: I/O error, dev mmcblk1, sector 7744019 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 51.055305] blk_update_request: I/O error, dev mmcblk1, sector 7744021 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 51.153477] Buffer I/O error on dev mmcblk1, logical block 968002, async page read [ 51.703137] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 53.348678] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 53.445287] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 53.612459] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 55.860904] xenbr0: port 1(eth0) entered blocking state [ 55.897045] xenbr0: port 1(eth0) entered disabled state [ 55.933866] device eth0 entered promiscuous mode [ 56.150926] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 56.210888] asix 3-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 [ 56.301020] xenbr0: port 1(eth0) entered blocking state [ 56.331978] xenbr0: port 1(eth0) entered forwarding state [ 56.368904] IPv6: ADDRCONF(NETDEV_CHANGE): xenbr0: link becomes ready