[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.274 (osstest@godello0) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 SMP Tue Apr 23 00:35:54 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on EXYNOS5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920 [ 0.000000] pcpu-alloc: s50636 r8192 d23092 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 412376K/524288K available (12288K kernel code, 1504K rwdata, 4764K rodata, 2048K init, 405K bss, 46376K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000016] Switching to timer-based delay loop, resolution 41ns [ 0.000422] Console: colour dummy device 80x30 [ 0.245402] printk: console [hvc0] enabled [ 0.249590] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.259991] CPU: Testing write buffer coherency: ok [ 0.264936] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.274489] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.280904] pid_max: default: 32768 minimum: 301 [ 0.285678] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.292972] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.301414] /cpus/cpu@0 missing clock-frequency property [ 0.306172] /cpus/cpu@1 missing clock-frequency property [ 0.311568] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.318766] xen:grant_table: Grant tables using version 1 layout [ 0.323442] Grant table initialized [ 0.327033] xen:events: Using FIFO-based ABI [ 0.331321] Xen: initializing cpu0 [ 0.334847] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.342570] rcu: Hierarchical SRCU implementation. [ 0.348708] EFI services will not be available. [ 0.351976] smp: Bringing up secondary CPUs ... [ 1.393012] CPU1: failed to come online [ 1.419354] smp: Brought up 1 node, 1 CPU [ 1.446811] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 1.492079] CPU: All CPU(s) started in SVC mode. [ 1.528696] devtmpfs: initialized [ 1.570086] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 1.617471] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 1.689647] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 1.736774] pinctrl core: initialized pinctrl subsystem [ 1.774137] DMI not present or invalid. [ 1.800062] NET: Registered protocol family 16 [ 1.838042] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 1.885489] xen:swiotlb_xen: Warning: only able to allocate 8 MB for software IO TLB [ 1.937832] software IO TLB: mapped [mem 0x7a000000-0x7a800000] (8MB) [ 1.981604] No ATAGs? [ 1.981769] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 2.047204] Serial: AMBA PL011 UART driver [ 2.098579] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 71 [ 2.207925] xen:balloon: Initialising balloon driver [ 2.246628] iommu: Default domain type: Translated [ 2.277709] vgaarb: loaded [ 2.296749] SCSI subsystem initialized [ 2.323198] libata version 3.00 loaded. [ 2.323478] usbcore: registered new interface driver usbfs [ 2.359876] usbcore: registered new interface driver hub [ 2.396490] usbcore: registered new device driver usb [ 2.434414] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.469113] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.554351] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.589866] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.625960] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.671262] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.707660] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 2.743747] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 2.789038] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 2.825378] s3c-i2c 121d0000.i2c: slave address 0x38 [ 2.861532] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 2.906690] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 2.943767] pps_core: LinuxPPS API ver. 1 registered [ 2.979315] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.043213] PTP clock support registered [ 3.070909] EDAC MC: Ver: 3.0.0 [ 3.100367] clocksource: Switched to clocksource arch_sys_counter [ 3.615672] thermal_sys: Registered thermal governor 'step_wise' [ 3.615872] OF: /thermal-zones/cpu-thermal/cooling-maps/map0: could not find phandle [ 3.711074] thermal_sys: Add a cooling_device property with at least one device [ 3.765321] thermal_sys: failed to build thermal zone cpu-thermal: -2 [ 3.811027] NET: Registered protocol family 2 [ 3.846673] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 3.901305] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 3.956043] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 4.010746] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 4.064837] TCP: Hash tables configured (established 4096 bind 4096) [ 4.110308] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 4.155936] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 4.202139] NET: Registered protocol family 1 [ 4.238166] RPC: Registered named UNIX socket transport module. [ 4.282754] RPC: Registered udp transport module. [ 4.318742] RPC: Registered tcp transport module. [ 4.354772] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.400358] PCI: CLS 0 bytes, default 64 [ 4.428289] Trying to unpack rootfs image as initramfs... [ 5.395894] Freeing initrd memory: 20012K [ 5.423171] Initialise system trusted keyrings [ 5.457608] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 5.512763] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 5.556511] NFS: Registering the id_resolver key type [ 5.592143] Key type id_resolver registered [ 5.619779] Key type id_legacy registered [ 5.647561] Key type asymmetric registered [ 5.674914] Asymmetric key parser 'x509' registered [ 5.711139] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 5.765454] io scheduler mq-deadline registered [ 5.801293] io scheduler kyber registered [ 5.870489] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 5.913714] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 5.971629] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 6.014842] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 6.071053] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 6.115962] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 6.172050] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-241330 [ 6.216996] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 6.278028] xen:xen_evtchn: Event-channel device installed [ 6.368395] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.413760] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 53, base_baud = 0) is a S3C6400/10 [ 6.473311] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 54, base_baud = 0) is a S3C6400/10 [ 6.536871] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 55, base_baud = 0) is a S3C6400/10 [ 6.600750] SuperH (H)SCI(F) driver initialized [ 6.637322] STMicroelectronics ASC driver initialized [ 6.674070] STM32 USART driver initialized [ 6.710422] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 6.764857] brd: module loaded [ 6.795852] loop: module loaded [ 6.841726] Invalid max_queues (4), will use default max: 1. [ 6.885842] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 6.938151] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 7.007280] tun: Universal TUN/TAP device driver, 1.6 [ 7.037546] CAN device driver interface [ 7.066047] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 7.117007] xen_netfront: Initialising Xen virtual ethernet driver [ 7.154877] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 7.209151] usbcore: registered new interface driver pegasus [ 7.253951] usbcore: registered new interface driver asix [ 7.290650] usbcore: registered new interface driver ax88179_178a [ 7.335873] usbcore: registered new interface driver cdc_ether [ 7.380861] usbcore: registered new interface driver smsc75xx [ 7.425720] usbcore: registered new interface driver smsc95xx [ 7.470591] usbcore: registered new interface driver net1080 [ 7.515375] usbcore: registered new interface driver cdc_subset [ 7.560427] usbcore: registered new interface driver zaurus [ 7.597335] usbcore: registered new interface driver cdc_ncm [ 7.643404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.687703] ehci-pci: EHCI PCI platform driver [ 7.723524] ehci-platform: EHCI generic platform driver [ 7.760305] ehci-orion: EHCI orion driver [ 7.787760] SPEAr-ehci: EHCI SPEAr driver [ 7.815266] ehci-st: EHCI STMicroelectronics driver [ 7.851472] ehci-atmel: EHCI Atmel driver [ 7.878962] tegra-ehci: Tegra EHCI driver [ 7.906530] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.951623] ohci-pci: OHCI PCI platform driver [ 7.987362] ohci-platform: OHCI generic platform driver [ 8.024159] SPEAr-ohci: OHCI SPEAr driver [ 8.051620] ohci-st: OHCI STMicroelectronics driver [ 8.087799] ohci-atmel: OHCI Atmel driver [ 8.116128] usbcore: registered new interface driver usb-storage [ 8.220910] s5m-rtc s5m-rtc: registered as rtc0 [ 8.262742] i2c /dev entries driver [ 8.295775] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff [ 8.375310] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 8.441836] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 8.485005] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 8.537084] device-mapper: uevent: version 1.0.3 [ 8.566520] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 8.630773] cpu cpu0: failed to get clock: -2 [ 8.665096] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 8.712408] failed to register cpuidle driver [ 8.745893] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 8.800609] sdhci: Secure Digital Host Controller Interface driver [ 8.845198] sdhci: Copyright(c) Pierre Ossman [ 8.885026] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.929638] ledtrig-cpu: registered to indicate activity on CPUs [ 8.971811] usbcore: registered new interface driver usbhid [ 9.007679] usbhid: USB HID core driver [ 9.040359] drop_monitor: Initializing network drop monitor service [ 9.081342] NET: Registered protocol family 10 [ 9.116903] Segment Routing with IPv6 [ 9.143425] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 9.188972] NET: Registered protocol family 17 [ 9.224207] can: controller area network core (rev 20170425 abi 9) [ 9.269507] NET: Registered protocol family 29 [ 9.305239] can: raw protocol (rev 20170425) [ 9.340830] can: broadcast manager protocol (rev 20170425 t) [ 9.385629] can: netlink gateway (rev 20190810) max_hops=1 [ 9.422824] Key type dns_resolver registered [ 9.458424] ThumbEE CPU extension supported. [ 9.493606] Registering SWP/SWPB emulation handler [ 9.530097] Loading compiled-in X.509 certificates [ 9.609668] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 9.660214] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 9.717534] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 9.760914] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 9.807393] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 9.861498] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 9.918676] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 9.962177] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 10.009629] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 10.054853] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 10.108613] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 10.165943] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 10.209275] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 10.260473] s5m-rtc s5m-rtc: setting system clock to 2024-04-23T03:49:36 UTC (1713844176) [ 10.309875] clk: Not disabling unused clocks [ 10.349077] Freeing unused kernel memory: 2048K [ 10.382467] Run /init as init process [ 12.507337] ohci-exynos: OHCI EXYNOS driver [ 12.537895] Synopsys Designware Multimedia Card Interface Driver [ 12.604277] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator [ 12.664855] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator [ 12.725230] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator [ 12.821712] ehci-exynos: EHCI EXYNOS driver [ 12.849214] exynos-ehci 12110000.usb: EHCI Host Controller [ 12.885504] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 12.950456] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 13.032666] s2mps11-clk s5m8767-clk: DMA mask not set [ 13.107612] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 13.270721] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 13.325524] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 13.380649] ahci 122f0000.sata: 122f0000.sata supply target not found, using dummy regulator [ 13.445437] wm8994: probe of 3-001a failed with error -22 [ 13.583100] gpio-6 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 13.646372] gpio-7 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 13.762906] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd33 not found, using dummy regulator [ 13.821174] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd10 not found, using dummy regulator [ 14.053562] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 14.094220] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 14.130987] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 100,32 bit host data width,128 deep fifo [ 14.195383] mmc_host mmc0: card is polling. [ 14.223273] exynos-ehci 12110000.usb: irq 102, io mem 0x12110000 [ 14.320530] debugfs: Directory 'VDD_33ON_2.8V' with parent 'regulator' already present! [ 14.463519] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 14.620768] i2c-gpio soc:i2c-gpio: using lines 6 (SDA) and 7 (SCL) [ 14.784173] hub 1-0:1.0: USB hub found [ 14.870536] ahci 122f0000.sata: SSS flag set, parallel bus scan disabled [ 14.916104] ahci 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 14.979351] ahci 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 15.158714] hub 1-0:1.0: 3 ports detected [ 15.266515] dwc3 12000000.dwc3: Failed to get clk 'ref': -2 [ 15.359064] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.424342] dwc3 12000000.dwc3: Configuration mismatch. dr_mode forced to host [ 15.476815] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 15.512507] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2 [ 15.569126] scsi host0: ahci [ 15.593937] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 98 [ 15.649920] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.694018] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 15.739310] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 15.791336] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 15.830902] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 15.867675] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 101,32 bit host data width,128 deep fifo [ 15.932764] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 15.996135] xhci-hcd xhci-hcd.2.auto: irq 146, io mem 0x12000000 [ 16.041404] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 16.077907] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 16.132518] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 16.178290] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 16.216244] s3c-rtc 101e0000.rtc: registered as rtc1 [ 16.253292] exynos-ohci 12120000.usb: USB Host Controller [ 16.291462] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.353605] hub 2-0:1.0: USB hub found [ 16.381846] hub 2-0:1.0: 1 port detected [ 16.408213] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 16.463395] hub 3-0:1.0: USB hub found [ 16.489536] hub 3-0:1.0: 1 port detected [ 16.518911] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 4 [ 16.571416] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 16.623334] exynos-ohci 12120000.usb: irq 102, io mem 0x12120000 [ 16.661778] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 16.707548] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 16.759705] hub 4-0:1.0: USB hub found [ 16.781092] hub 4-0:1.0: 3 ports detected [ 16.810612] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 16.853672] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 16.902084] ata1.00: configured for UDMA/133 [ 16.934936] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 17.000124] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 17.051854] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 17.090565] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 17.155566] mmc0: new DDR MMC card at address 0001 [ 17.189766] sd 0:0:0:0: [sda] Write Protect is off [ 17.225076] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 17.225563] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 17.261206] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB [ 17.306224] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB [ 17.351110] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.415618] mmc1: new high speed SDHC card at address aaaa [ 17.452955] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 17.518392] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 17.552131] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB, chardev (237:0) [ 17.606287] sda: sda1 sda2 < sda5 > [ 17.642839] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.686608] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.733306] sd 0:0:0:0: [sda] Attached SCSI disk [ 17.833954] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 17.876065] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.921758] mmcblk0: p1 p2 p3 p4 [ 17.993613] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 18.032882] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 18.353858] random: lvm: uninitialized urandom read (4 bytes read) [ 18.489343] random: lvm: uninitialized urandom read (4 bytes read) [ 18.546080] random: lvm: uninitialized urandom read (2 bytes read) [ 19.170431] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 19.347607] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 19.741052] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 20.142724] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 20.544519] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 20.946329] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 21.348124] blk_update_request: I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 21.762838] blk_update_request: I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 22.199835] blk_update_request: I/O error, dev mmcblk1, sector 7744012 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 0 [ 22.622045] blk_update_request: I/O error, dev mmcblk1, sector 7744016 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 23.025591] blk_update_request: I/O error, dev mmcblk1, sector 7744017 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 23.427418] blk_update_request: I/O error, dev mmcblk1, sector 7744018 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 24.864168] print_req_error: 3 callbacks suppressed [ 24.864176] blk_update_request: I/O error, dev mmcblk1, sector 7744026 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 25.306212] blk_update_request: I/O error, dev mmcblk1, sector 7744027 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 26.140424] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 26.318549] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 26.711796] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.120845] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.522194] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 27.923560] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 28.324904] blk_update_request: I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 28.739622] blk_update_request: I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 29.143282] blk_update_request: I/O error, dev mmcblk1, sector 7744007 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 29.208914] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 32.992339] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 33.404221] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 38.437428] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 38.482591] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 38.569412] mc: Linux media interface: v0.10 [ 38.630614] s5p-secss 10830000.sss: s5p-sss driver registered [ 39.106554] videodev: Linux video capture interface: v2.00 [ 39.280425] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 39.319949] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 39.435527] s5p-mfc 11000000.codec: ignoring dependency for device, assuming no driver [ 39.530566] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 39.597119] exynos-gsc 13e00000.gsc: ignoring dependency for device, assuming no driver [ 39.737928] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 39.810608] exynos-gsc 13e10000.gsc: ignoring dependency for device, assuming no driver [ 39.872636] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 39.915440] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 39.961545] exynos-gsc 13e20000.gsc: ignoring dependency for device, assuming no driver [ 40.022757] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 40.061303] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 40.110516] exynos-gsc 13e30000.gsc: ignoring dependency for device, assuming no driver [ 40.161913] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 40.335477] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 40.374802] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 40.443843] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 40.489176] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 40.534248] usb3503 usb-hub: switched to HUB mode [ 40.570264] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 40.617310] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 40.702391] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 40.742467] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 40.860794] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 41.028565] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 41.245442] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 41.290009] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 41.336240] MAIN_DC: disabling [ 41.361838] hdmi-en: disabling [ 41.388333] VCC_1V2: disabling [ 41.414896] VCC_1V8: disabling [ 41.441516] VCC_3V3: disabling [ 41.487824] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 41.566748] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 41.820428] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 41.893094] blk_update_request: I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 42.180826] random: lvm: uninitialized urandom read (4 bytes read) [ 42.295135] blk_update_request: I/O error, dev mmcblk1, sector 7744005 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 42.389269] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 42.492593] hub 1-3:1.0: USB hub found [ 42.634209] hub 1-3:1.0: 3 ports detected [ 42.703183] blk_update_request: I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 42.924889] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 42.964729] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 43.010377] random: crng init done [ 43.093278] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 43.155045] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 43.228476] blk_update_request: I/O error, dev mmcblk1, sector 7744015 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 0 [ 43.397569] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 43.442325] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 43.489639] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 43.532410] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 43.603190] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 43.664822] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 43.728171] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 43.801283] blk_update_request: I/O error, dev mmcblk1, sector 7744016 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 43.900502] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 43.962043] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 44.025446] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 44.160414] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 44.210583] blk_update_request: I/O error, dev mmcblk1, sector 7744017 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 44.404467] hub 1-3.2:1.0: USB hub found [ 44.425748] hub 1-3.2:1.0: 4 ports detected [ 44.459144] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 44.498720] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 44.770406] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 44.981445] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 45.300825] print_req_error: 2 callbacks suppressed [ 45.300834] blk_update_request: I/O error, dev mmcblk1, sector 7744021 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 0 [ 45.671630] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 4e:0a:f8:e6:c2:59 [ 45.754054] blk_update_request: I/O error, dev mmcblk1, sector 7744024 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 45.827607] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 45.871349] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 46.161381] blk_update_request: I/O error, dev mmcblk1, sector 7744025 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 46.568140] blk_update_request: I/O error, dev mmcblk1, sector 7744026 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 46.969897] blk_update_request: I/O error, dev mmcblk1, sector 7744027 op 0x0:(READ) flags 0x80700 phys_seg 11 prio class 0 [ 47.810430] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 47.988555] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 48.383280] blk_update_request: I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 48.784538] blk_update_request: I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 49.185916] blk_update_request: I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 49.587282] blk_update_request: I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.002015] blk_update_request: I/O error, dev mmcblk1, sector 7744005 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 50.083953] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 50.640565] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 52.297200] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 52.393808] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 52.561072] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 54.740996] xenbr0: port 1(eth0) entered blocking state [ 54.772965] xenbr0: port 1(eth0) entered disabled state [ 54.809815] device eth0 entered promiscuous mode [ 55.111093] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 55.170991] asix 1-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 [ 55.280948] xenbr0: port 1(eth0) entered blocking state [ 55.317310] xenbr0: port 1(eth0) entered forwarding state [ 55.409167] IPv6: ADDRCONF(NETDEV_CHANGE): xenbr0: link becomes ready