[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.274 (osstest@godello0) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 SMP Tue Apr 23 00:35:54 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on EXYNOS5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920 [ 0.000000] pcpu-alloc: s50636 r8192 d23092 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 412376K/524288K available (12288K kernel code, 1504K rwdata, 4764K rodata, 2048K init, 405K bss, 46376K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000015] Switching to timer-based delay loop, resolution 41ns [ 0.000420] Console: colour dummy device 80x30 [ 0.245055] printk: console [hvc0] enabled [ 0.249265] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.259654] CPU: Testing write buffer coherency: ok [ 0.264590] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.274141] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.280556] pid_max: default: 32768 minimum: 301 [ 0.285329] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.292625] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.301062] /cpus/cpu@0 missing clock-frequency property [ 0.305826] /cpus/cpu@1 missing clock-frequency property [ 0.311222] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.318413] xen:grant_table: Grant tables using version 1 layout [ 0.323085] Grant table initialized [ 0.326654] xen:events: Using FIFO-based ABI [ 0.330966] Xen: initializing cpu0 [ 0.334492] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.342219] rcu: Hierarchical SRCU implementation. [ 0.348330] EFI services will not be available. [ 0.351602] smp: Bringing up secondary CPUs ... [ 0.422996] Xen: initializing cpu1 [ 0.423076] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.423088] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.442087] smp: Brought up 1 node, 2 CPUs [ 0.445790] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.452075] CPU: All CPU(s) started in SVC mode. [ 0.457533] devtmpfs: initialized [ 0.469214] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.475703] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.485438] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.493283] pinctrl core: initialized pinctrl subsystem [ 0.499122] DMI not present or invalid. [ 0.502131] NET: Registered protocol family 16 [ 0.508003] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.516718] xen:swiotlb_xen: Warning: only able to allocate 8 MB for software IO TLB [ 0.524812] software IO TLB: mapped [mem 0x7a000000-0x7a800000] (8MB) [ 0.529985] No ATAGs? [ 0.530099] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.540709] Serial: AMBA PL011 UART driver [ 0.565806] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 71 [ 0.611920] xen:balloon: Initialising balloon driver [ 0.619297] iommu: Default domain type: Translated [ 0.623095] vgaarb: loaded [ 0.626314] SCSI subsystem initialized [ 0.629517] libata version 3.00 loaded. [ 0.629691] usbcore: registered new interface driver usbfs [ 0.634974] usbcore: registered new interface driver hub [ 0.640407] usbcore: registered new device driver usb [ 0.646565] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.650513] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.690794] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.694887] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.699771] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.705893] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.711124] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.716013] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.722076] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.727297] s3c-i2c 121d0000.i2c: slave address 0x38 [ 0.732224] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.738240] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.744061] pps_core: LinuxPPS API ver. 1 registered [ 0.748470] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.757663] PTP clock support registered [ 0.761847] EDAC MC: Ver: 3.0.0 [ 0.767202] clocksource: Switched to clocksource arch_sys_counter [ 1.214337] thermal_sys: Registered thermal governor 'step_wise' [ 1.214507] OF: /thermal-zones/cpu-thermal/cooling-maps/map0: could not find phandle [ 1.226945] thermal_sys: Add a cooling_device property with at least one device [ 1.234338] thermal_sys: failed to build thermal zone cpu-thermal: -2 [ 1.240958] NET: Registered protocol family 2 [ 1.245383] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.253145] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.261030] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.268832] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.276054] TCP: Hash tables configured (established 4096 bind 4096) [ 1.282468] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.289035] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.296133] NET: Registered protocol family 1 [ 1.301042] RPC: Registered named UNIX socket transport module. [ 1.306453] RPC: Registered udp transport module. [ 1.311248] RPC: Registered tcp transport module. [ 1.316002] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.322528] PCI: CLS 0 bytes, default 64 [ 1.326843] Trying to unpack rootfs image as initramfs... [ 2.212377] Freeing initrd memory: 20012K [ 2.216440] Initialise system trusted keyrings [ 2.219792] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 2.231309] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.236330] NFS: Registering the id_resolver key type [ 2.240977] Key type id_resolver registered [ 2.245135] Key type id_legacy registered [ 2.249820] Key type asymmetric registered [ 2.253399] Asymmetric key parser 'x509' registered [ 2.258370] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 2.265795] io scheduler mq-deadline registered [ 2.270405] io scheduler kyber registered [ 2.303182] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 2.308521] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2.318492] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 2.323832] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2.332849] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 2.339043] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 2.347927] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-241330 [ 2.354123] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 2.366932] xen:xen_evtchn: Event-channel device installed [ 2.447345] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.455747] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 53, base_baud = 0) is a S3C6400/10 [ 2.463721] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 54, base_baud = 0) is a S3C6400/10 [ 2.472594] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 55, base_baud = 0) is a S3C6400/10 [ 2.481767] SuperH (H)SCI(F) driver initialized [ 2.486861] STMicroelectronics ASC driver initialized [ 2.492291] STM32 USART driver initialized [ 2.497240] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 2.511047] brd: module loaded [ 2.517590] loop: module loaded [ 2.531344] Invalid max_queues (4), will use default max: 2. [ 2.537763] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 2.544702] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 2.562480] tun: Universal TUN/TAP device driver, 1.6 [ 2.566373] CAN device driver interface [ 2.571125] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.581276] xen_netfront: Initialising Xen virtual ethernet driver [ 2.586140] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.593586] usbcore: registered new interface driver pegasus [ 2.599300] usbcore: registered new interface driver asix [ 2.604754] usbcore: registered new interface driver ax88179_178a [ 2.610928] usbcore: registered new interface driver cdc_ether [ 2.616826] usbcore: registered new interface driver smsc75xx [ 2.622655] usbcore: registered new interface driver smsc95xx [ 2.628460] usbcore: registered new interface driver net1080 [ 2.634183] usbcore: registered new interface driver cdc_subset [ 2.640176] usbcore: registered new interface driver zaurus [ 2.645832] usbcore: registered new interface driver cdc_ncm [ 2.652526] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.658126] ehci-pci: EHCI PCI platform driver [ 2.662652] ehci-platform: EHCI generic platform driver [ 2.668169] ehci-orion: EHCI orion driver [ 2.672189] SPEAr-ehci: EHCI SPEAr driver [ 2.676224] ehci-st: EHCI STMicroelectronics driver [ 2.681181] ehci-atmel: EHCI Atmel driver [ 2.685249] tegra-ehci: Tegra EHCI driver [ 2.689366] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.695451] ohci-pci: OHCI PCI platform driver [ 2.699988] ohci-platform: OHCI generic platform driver [ 2.705436] SPEAr-ohci: OHCI SPEAr driver [ 2.709494] ohci-st: OHCI STMicroelectronics driver [ 2.714416] ohci-atmel: OHCI Atmel driver [ 2.719124] usbcore: registered new interface driver usb-storage [ 2.753040] s5m-rtc s5m-rtc: registered as rtc0 [ 2.759402] i2c /dev entries driver [ 2.768933] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff [ 2.779048] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 2.790137] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.795276] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 2.806191] device-mapper: uevent: version 1.0.3 [ 2.809729] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 2.818826] cpu cpu0: failed to get clock: -2 [ 2.822364] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 2.830155] failed to register cpuidle driver [ 2.833130] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 2.840692] sdhci: Secure Digital Host Controller Interface driver [ 2.846492] sdhci: Copyright(c) Pierre Ossman [ 2.853931] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.861110] ledtrig-cpu: registered to indicate activity on CPUs [ 2.866431] usbcore: registered new interface driver usbhid [ 2.871388] usbhid: USB HID core driver [ 2.879040] drop_monitor: Initializing network drop monitor service [ 2.884527] NET: Registered protocol family 10 [ 2.889127] Segment Routing with IPv6 [ 2.892242] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.898585] NET: Registered protocol family 17 [ 2.902694] can: controller area network core (rev 20170425 abi 9) [ 2.908975] NET: Registered protocol family 29 [ 2.913451] can: raw protocol (rev 20170425) [ 2.917787] can: broadcast manager protocol (rev 20170425 t) [ 2.923510] can: netlink gateway (rev 20190810) max_hops=1 [ 2.929385] Key type dns_resolver registered [ 2.933832] ThumbEE CPU extension supported. [ 2.937756] Registering SWP/SWPB emulation handler [ 2.942902] Loading compiled-in X.509 certificates [ 2.967453] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 2.974416] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 2.984305] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.989461] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 2.996576] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 3.004155] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 3.013875] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 3.018997] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 3.026713] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 3.033187] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 3.040460] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 3.048643] s5m-rtc s5m-rtc: setting system clock to 2024-04-23T02:35:34 UTC (1713839734) [ 3.048844] clk: Not disabling unused clocks [ 3.059212] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 3.067851] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 3.076742] Freeing unused kernel memory: 2048K [ 3.098634] Run /init as init process [ 4.225364] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator [ 4.233600] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator [ 4.233740] ohci-exynos: OHCI EXYNOS driver [ 4.250315] ehci-exynos: EHCI EXYNOS driver [ 4.254366] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator [ 4.255674] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 4.270755] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 4.281217] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 4.286441] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 4.286613] Synopsys Designware Multimedia Card Interface Driver [ 4.296911] exynos-ohci 12120000.usb: USB Host Controller [ 4.304221] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 4.319279] exynos-ohci 12120000.usb: irq 102, io mem 0x12120000 [ 4.328171] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.334209] s2mps11-clk s5m8767-clk: DMA mask not set [ 4.341384] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.346465] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.352043] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 100,32 bit host data width,128 deep fifo [ 4.361656] mmc_host mmc0: card is polling. [ 4.413935] hub 1-0:1.0: USB hub found [ 4.422390] hub 1-0:1.0: 3 ports detected [ 4.432561] gpio-6 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 4.433352] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd33 not found, using dummy regulator [ 4.440864] gpio-7 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 4.449727] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd10 not found, using dummy regulator [ 4.471179] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 4.476163] wm8994: probe of 3-001a failed with error -22 [ 4.485057] exynos-ehci 12110000.usb: EHCI Host Controller [ 4.491297] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 4.523707] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.529354] i2c-gpio soc:i2c-gpio: using lines 6 (SDA) and 7 (SCL) [ 4.557430] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.595595] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.600719] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.606204] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 101,32 bit host data width,128 deep fifo [ 4.617667] exynos-ehci 12110000.usb: irq 102, io mem 0x12110000 [ 4.657540] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 4.672516] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.673525] hub 2-0:1.0: USB hub found [ 4.721635] hub 2-0:1.0: 3 ports detected [ 4.725738] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 4.732754] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 4.737501] debugfs: Directory 'VDD_33ON_2.8V' with parent 'regulator' already present! [ 4.741023] ahci 122f0000.sata: 122f0000.sata supply target not found, using dummy regulator [ 4.807319] ahci 122f0000.sata: SSS flag set, parallel bus scan disabled [ 4.812679] ahci 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.821262] ahci 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 4.838026] scsi host0: ahci [ 4.839846] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 98 [ 4.848960] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 4.854112] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 4.867701] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.870870] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.888317] mmc1: new high speed SDHC card at address aaaa [ 4.895057] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.899701] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.906343] mmc0: new DDR MMC card at address 0001 [ 4.914483] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.919613] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 4.924780] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 4.932060] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.935897] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB [ 4.941894] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB [ 4.949133] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB, chardev (237:0) [ 4.959839] mmcblk0: p1 p2 p3 p4 [ 4.965745] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 4.970948] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.048806] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.053976] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.126506] dwc3 12000000.dwc3: Failed to get clk 'ref': -2 [ 5.150172] dwc3 12000000.dwc3: Configuration mismatch. dr_mode forced to host [ 5.156921] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.161634] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.170153] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 5.178906] xhci-hcd xhci-hcd.2.auto: irq 146, io mem 0x12000000 [ 5.184989] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.190429] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.198137] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.205782] hub 3-0:1.0: USB hub found [ 5.208805] hub 3-0:1.0: 1 port detected [ 5.214211] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.217584] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.219420] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.234564] hub 4-0:1.0: USB hub found [ 5.237789] hub 4-0:1.0: 1 port detected [ 5.243471] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.248666] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.397371] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.403090] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.409055] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.416555] ata1.00: configured for UDMA/133 [ 5.420249] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.429022] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 5.435598] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 5.441053] sd 0:0:0:0: [sda] Write Protect is off [ 5.445750] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.445825] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.516713] sda: sda1 sda2 < sda5 > [ 5.520172] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.525131] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.530330] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.847893] random: lvm: uninitialized urandom read (4 bytes read) [ 5.857268] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.968703] random: lvm: uninitialized urandom read (4 bytes read) [ 5.974880] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.989737] random: lvm: uninitialized urandom read (2 bytes read) [ 6.319251] blk_update_request: I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.664634] blk_update_request: I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7.010014] blk_update_request: I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7.355361] blk_update_request: I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 7.700703] blk_update_request: I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 8.046045] blk_update_request: I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 8.391385] blk_update_request: I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 8.736728] blk_update_request: I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 9.753624] blk_update_request: I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 10.098621] blk_update_request: I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 11.450615] print_req_error: 3 callbacks suppressed [ 11.450622] blk_update_request: I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 11.800560] blk_update_request: I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 12.145552] blk_update_request: I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 12.154875] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 15.660180] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 15.879321] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 19.678144] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 19.683376] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 19.730688] s5p-secss 10830000.sss: s5p-sss driver registered [ 19.737109] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 19.742310] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 19.751776] mc: Linux media interface: v0.10 [ 19.862242] videodev: Linux video capture interface: v2.00 [ 19.985224] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 19.990429] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.237269] usb3503 usb-hub: switched to HUB mode [ 20.240602] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 20.248115] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.253310] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.313014] exynos-gsc 13e00000.gsc: ignoring dependency for device, assuming no driver [ 20.327657] exynos-gsc 13e10000.gsc: ignoring dependency for device, assuming no driver [ 20.335799] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.345725] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.357956] exynos-gsc 13e20000.gsc: ignoring dependency for device, assuming no driver [ 20.366229] s5p-mfc 11000000.codec: ignoring dependency for device, assuming no driver [ 20.367767] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.384159] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.392452] exynos-gsc 13e30000.gsc: ignoring dependency for device, assuming no driver [ 20.402071] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.407324] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.444676] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 20.487873] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 20.540912] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 20.573258] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 20.580666] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 20.611990] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 20.625728] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 20.662304] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 20.685066] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 20.692755] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.697985] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.710612] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.715773] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.879689] hub 2-3:1.0: USB hub found [ 20.882456] hub 2-3:1.0: 3 ports detected [ 20.895288] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 20.904429] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 20.909621] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 20.970012] blk_update_request: I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 21.157815] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 21.165470] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 21.174205] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 21.197565] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 21.205254] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 21.213961] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 21.224525] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 21.315438] blk_update_request: I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 21.389824] hub 2-3.2:1.0: USB hub found [ 21.392824] hub 2-3.2:1.0: 4 ports detected [ 21.408853] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 21.414091] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 21.656039] random: lvm: uninitialized urandom read (4 bytes read) [ 21.660876] blk_update_request: I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 21.717233] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 21.880571] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 22.007709] blk_update_request: I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 22.353061] blk_update_request: I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 22.408270] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 8a:d5:0d:3e:6b:40 [ 22.420339] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 22.425557] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 22.698416] blk_update_request: I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 23.043790] blk_update_request: I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 23.389151] blk_update_request: I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 24.406062] blk_update_request: I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 24.751057] blk_update_request: I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 26.103038] print_req_error: 3 callbacks suppressed [ 26.103045] blk_update_request: I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 26.452992] blk_update_request: I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 26.797988] blk_update_request: I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 26.807319] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 27.172429] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 28.285630] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 28.334507] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 28.467238] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 28.902900] random: dd: uninitialized urandom read (32 bytes read) [ 30.267820] xenbr0: port 1(eth0) entered blocking state [ 30.271686] xenbr0: port 1(eth0) entered disabled state [ 30.277107] device eth0 entered promiscuous mode [ 30.457842] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 30.477818] asix 2-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 [ 30.537820] xenbr0: port 1(eth0) entered blocking state [ 30.541687] xenbr0: port 1(eth0) entered forwarding state [ 30.547296] IPv6: ADDRCONF(NETDEV_CHANGE): xenbr0: link becomes ready [ 32.277197] random: crng init done [ 33.297274] MAIN_DC: disabling [ 33.298958] hdmi-en: disabling [ 33.302080] VCC_1V2: disabling [ 33.305204] VCC_1V8: disabling [ 33.308344] VCC_3V3: disabling