[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.274 (osstest@himrod2) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 SMP Tue Apr 23 13:06:26 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on EXYNOS5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920 [ 0.000000] pcpu-alloc: s50636 r8192 d23092 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 412380K/524288K available (12288K kernel code, 1504K rwdata, 4764K rodata, 2048K init, 405K bss, 46372K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000015] Switching to timer-based delay loop, resolution 41ns [ 0.000421] Console: colour dummy device 80x30 [ 0.244802] printk: console [hvc0] enabled [ 0.248988] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.259390] CPU: Testing write buffer coherency: ok [ 0.264336] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.273889] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.280303] pid_max: default: 32768 minimum: 301 [ 0.285076] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.292371] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.300817] /cpus/cpu@0 missing clock-frequency property [ 0.305572] /cpus/cpu@1 missing clock-frequency property [ 0.310968] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.318162] xen:grant_table: Grant tables using version 1 layout [ 0.322832] Grant table initialized [ 0.326422] xen:events: Using FIFO-based ABI [ 0.330712] Xen: initializing cpu0 [ 0.334238] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.341959] rcu: Hierarchical SRCU implementation. [ 0.348103] EFI services will not be available. [ 0.351375] smp: Bringing up secondary CPUs ... [ 0.422640] Xen: initializing cpu1 [ 0.422723] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.422735] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.441736] smp: Brought up 1 node, 2 CPUs [ 0.445450] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.451757] CPU: All CPU(s) started in SVC mode. [ 0.457210] devtmpfs: initialized [ 0.468886] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.475360] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.485089] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.492951] pinctrl core: initialized pinctrl subsystem [ 0.498747] DMI not present or invalid. [ 0.501742] NET: Registered protocol family 16 [ 0.507581] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.516329] xen:swiotlb_xen: Warning: only able to allocate 8 MB for software IO TLB [ 0.524422] software IO TLB: mapped [mem 0x7a000000-0x7a800000] (8MB) [ 0.529590] No ATAGs? [ 0.529704] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.540300] Serial: AMBA PL011 UART driver [ 0.565569] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 71 [ 0.611826] xen:balloon: Initialising balloon driver [ 0.619116] iommu: Default domain type: Translated [ 0.622981] vgaarb: loaded [ 0.626100] SCSI subsystem initialized [ 0.629330] libata version 3.00 loaded. [ 0.629502] usbcore: registered new interface driver usbfs [ 0.634876] usbcore: registered new interface driver hub [ 0.640176] usbcore: registered new device driver usb [ 0.646407] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.650310] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.696420] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.700502] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.705393] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.711522] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.716759] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.721646] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.727711] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.732944] s3c-i2c 121d0000.i2c: slave address 0x38 [ 0.737856] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.743874] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.749672] pps_core: LinuxPPS API ver. 1 registered [ 0.754106] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.763314] PTP clock support registered [ 0.767474] EDAC MC: Ver: 3.0.0 [ 0.772846] clocksource: Switched to clocksource arch_sys_counter [ 1.218260] thermal_sys: Registered thermal governor 'step_wise' [ 1.218430] OF: /thermal-zones/cpu-thermal/cooling-maps/map0: could not find phandle [ 1.230867] thermal_sys: Add a cooling_device property with at least one device [ 1.238260] thermal_sys: failed to build thermal zone cpu-thermal: -2 [ 1.244881] NET: Registered protocol family 2 [ 1.249307] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.257069] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.264958] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.272735] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.279991] TCP: Hash tables configured (established 4096 bind 4096) [ 1.286412] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.292966] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.300054] NET: Registered protocol family 1 [ 1.304981] RPC: Registered named UNIX socket transport module. [ 1.310376] RPC: Registered udp transport module. [ 1.315171] RPC: Registered tcp transport module. [ 1.319923] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.326468] PCI: CLS 0 bytes, default 64 [ 1.330776] Trying to unpack rootfs image as initramfs... [ 2.210791] Freeing initrd memory: 20008K [ 2.214569] Initialise system trusted keyrings [ 2.218302] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 2.229782] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.235120] NFS: Registering the id_resolver key type [ 2.239373] Key type id_resolver registered [ 2.243627] Key type id_legacy registered [ 2.247970] Key type asymmetric registered [ 2.251853] Asymmetric key parser 'x509' registered [ 2.256868] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 2.264283] io scheduler mq-deadline registered [ 2.268866] io scheduler kyber registered [ 2.301510] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 2.306879] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2.316837] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 2.322156] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 2.331216] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 2.337392] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 2.346317] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-241330 [ 2.352449] dma-pl330 11c10000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 2.365363] xen:xen_evtchn: Event-channel device installed [ 2.448281] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.456727] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 53, base_baud = 0) is a S3C6400/10 [ 2.464708] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 54, base_baud = 0) is a S3C6400/10 [ 2.473592] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 55, base_baud = 0) is a S3C6400/10 [ 2.482733] SuperH (H)SCI(F) driver initialized [ 2.487906] STMicroelectronics ASC driver initialized [ 2.493307] STM32 USART driver initialized [ 2.502900] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 2.516745] brd: module loaded [ 2.523406] loop: module loaded [ 2.537195] Invalid max_queues (4), will use default max: 2. [ 2.543631] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 2.550574] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 2.568336] tun: Universal TUN/TAP device driver, 1.6 [ 2.572241] CAN device driver interface [ 2.577013] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.587132] xen_netfront: Initialising Xen virtual ethernet driver [ 2.591999] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.599433] usbcore: registered new interface driver pegasus [ 2.605163] usbcore: registered new interface driver asix [ 2.610612] usbcore: registered new interface driver ax88179_178a [ 2.616785] usbcore: registered new interface driver cdc_ether [ 2.622684] usbcore: registered new interface driver smsc75xx [ 2.628516] usbcore: registered new interface driver smsc95xx [ 2.634323] usbcore: registered new interface driver net1080 [ 2.640042] usbcore: registered new interface driver cdc_subset [ 2.646036] usbcore: registered new interface driver zaurus [ 2.651691] usbcore: registered new interface driver cdc_ncm [ 2.658420] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.663983] ehci-pci: EHCI PCI platform driver [ 2.668509] ehci-platform: EHCI generic platform driver [ 2.674007] ehci-orion: EHCI orion driver [ 2.678045] SPEAr-ehci: EHCI SPEAr driver [ 2.682082] ehci-st: EHCI STMicroelectronics driver [ 2.687042] ehci-atmel: EHCI Atmel driver [ 2.691103] tegra-ehci: Tegra EHCI driver [ 2.695224] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.701312] ohci-pci: OHCI PCI platform driver [ 2.705850] ohci-platform: OHCI generic platform driver [ 2.711294] SPEAr-ohci: OHCI SPEAr driver [ 2.715340] ohci-st: OHCI STMicroelectronics driver [ 2.720275] ohci-atmel: OHCI Atmel driver [ 2.724976] usbcore: registered new interface driver usb-storage [ 2.793272] s5m-rtc s5m-rtc: registered as rtc0 [ 2.804494] i2c /dev entries driver [ 2.814034] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff [ 2.824148] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 2.835267] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.840426] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 2.851334] device-mapper: uevent: version 1.0.3 [ 2.854882] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 2.863985] cpu cpu0: failed to get clock: -2 [ 2.867506] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 2.875325] failed to register cpuidle driver [ 2.878300] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 2.885880] sdhci: Secure Digital Host Controller Interface driver [ 2.891663] sdhci: Copyright(c) Pierre Ossman [ 2.899095] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.906293] ledtrig-cpu: registered to indicate activity on CPUs [ 2.911630] usbcore: registered new interface driver usbhid [ 2.916594] usbhid: USB HID core driver [ 2.924216] drop_monitor: Initializing network drop monitor service [ 2.929700] NET: Registered protocol family 10 [ 2.934342] Segment Routing with IPv6 [ 2.937395] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.943785] NET: Registered protocol family 17 [ 2.947872] can: controller area network core (rev 20170425 abi 9) [ 2.954158] NET: Registered protocol family 29 [ 2.958614] can: raw protocol (rev 20170425) [ 2.962972] can: broadcast manager protocol (rev 20170425 t) [ 2.968688] can: netlink gateway (rev 20190810) max_hops=1 [ 2.974531] Key type dns_resolver registered [ 2.979019] ThumbEE CPU extension supported. [ 2.982943] Registering SWP/SWPB emulation handler [ 2.988093] Loading compiled-in X.509 certificates [ 3.012519] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 3.019529] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 3.029354] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 3.034520] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 3.041653] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 3.049187] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 3.058912] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 3.064043] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 3.071785] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 3.078286] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 3.085535] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 3.095331] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 3.100489] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 3.112950] s5m-rtc s5m-rtc: setting system clock to 2024-04-23T18:26:27 UTC (1713896787) [ 3.119913] clk: Not disabling unused clocks [ 3.127464] Freeing unused kernel memory: 2048K [ 3.134262] Run /init as init process [ 4.346723] ehci-exynos: EHCI EXYNOS driver [ 4.353007] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator [ 4.361087] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator [ 4.371338] ohci-exynos: OHCI EXYNOS driver [ 4.376606] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 4.383704] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 4.392795] Synopsys Designware Multimedia Card Interface Driver [ 4.433160] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.441107] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator [ 4.454078] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 4.459307] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 4.471749] s2mps11-clk s5m8767-clk: DMA mask not set [ 4.485733] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.490845] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.496395] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 100,32 bit host data width,128 deep fifo [ 4.505999] mmc_host mmc0: card is polling. [ 4.513201] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.517542] rtc rtc1: invalid alarm value: 1900-01-30T00:00:00 [ 4.522961] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.525438] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.539741] exynos-ehci 12110000.usb: EHCI Host Controller [ 4.543912] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 4.551745] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 4.567173] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.582641] gpio-6 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 4.588315] wm8994: probe of 3-001a failed with error -22 [ 4.590926] gpio-7 (soc:i2c-gpio): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 4.634676] i2c-gpio soc:i2c-gpio: using lines 6 (SDA) and 7 (SCL) [ 4.670914] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.676024] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.681530] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 101,32 bit host data width,128 deep fifo [ 4.681557] exynos-ehci 12110000.usb: irq 102, io mem 0x12110000 [ 4.707463] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd33 not found, using dummy regulator [ 4.714971] exynos-dwc3 soc:usb_dwc3: soc:usb_dwc3 supply vdd10 not found, using dummy regulator [ 4.727019] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 4.743904] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.754136] hub 1-0:1.0: USB hub found [ 4.756585] hub 1-0:1.0: 3 ports detected [ 4.762606] exynos-ohci 12120000.usb: USB Host Controller [ 4.766727] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 4.802332] exynos-ohci 12120000.usb: irq 102, io mem 0x12120000 [ 4.803776] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.834050] mmc0: new DDR MMC card at address 0001 [ 4.838793] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.842517] mmcblk0boot0: mmc0:0001 M4G1FB partition 1 1.00 MiB [ 4.848537] mmcblk0boot1: mmc0:0001 M4G1FB partition 2 1.00 MiB [ 4.860408] mmcblk0rpmb: mmc0:0001 M4G1FB partition 3 128 KiB, chardev (237:0) [ 4.876040] mmcblk0: p1 p2 p3 p4 [ 4.878057] hub 2-0:1.0: USB hub found [ 4.882919] hub 2-0:1.0: 3 ports detected [ 4.887355] ahci 122f0000.sata: 122f0000.sata supply ahci not found, using dummy regulator [ 4.894344] ahci 122f0000.sata: 122f0000.sata supply phy not found, using dummy regulator [ 4.902569] ahci 122f0000.sata: 122f0000.sata supply target not found, using dummy regulator [ 4.937941] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.943232] ahci 122f0000.sata: SSS flag set, parallel bus scan disabled [ 4.946465] mmc1: new high speed SDHC card at address aaaa [ 4.953130] ahci 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 4.961106] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.967259] ahci 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 4.986623] scsi host0: ahci [ 4.988426] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 98 [ 4.997472] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.002716] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.113061] debugfs: Directory 'VDD_33ON_2.8V' with parent 'regulator' already present! [ 5.250895] dwc3 12000000.dwc3: Failed to get clk 'ref': -2 [ 5.258109] dwc3 12000000.dwc3: Configuration mismatch. dr_mode forced to host [ 5.269907] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.274084] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.289669] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 5.297846] xhci-hcd xhci-hcd.2.auto: irq 146, io mem 0x12000000 [ 5.303947] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.309335] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.317070] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.324983] hub 3-0:1.0: USB hub found [ 5.325544] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.327509] hub 3-0:1.0: 1 port detected [ 5.334131] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.338417] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.353114] hub 4-0:1.0: USB hub found [ 5.356309] hub 4-0:1.0: 1 port detected [ 5.370218] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.375412] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.532886] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.538627] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.544474] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.552142] ata1.00: configured for UDMA/133 [ 5.555661] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.564455] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 5.571115] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 5.576599] sd 0:0:0:0: [sda] Write Protect is off [ 5.581262] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.581337] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.650970] sda: sda1 sda2 < sda5 > [ 5.654446] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.659339] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 5.664530] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 5.987653] random: lvm: uninitialized urandom read (4 bytes read) [ 6.134120] random: lvm: uninitialized urandom read (4 bytes read) [ 6.153517] random: lvm: uninitialized urandom read (2 bytes read) [ 9.931094] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 10.199245] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 13.801265] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 13.803997] s5p-secss 10830000.sss: s5p-sss driver registered [ 13.806513] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 13.919649] mc: Linux media interface: v0.10 [ 13.925814] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 13.931073] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 13.965691] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 13.970938] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.038588] videodev: Linux video capture interface: v2.00 [ 14.414084] exynos-gsc 13e00000.gsc: ignoring dependency for device, assuming no driver [ 14.425567] s5p-mfc 11000000.codec: ignoring dependency for device, assuming no driver [ 14.425638] exynos-gsc 13e10000.gsc: ignoring dependency for device, assuming no driver [ 14.441890] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 14.447080] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.454115] exynos-gsc 13e20000.gsc: ignoring dependency for device, assuming no driver [ 14.462942] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 14.468212] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.495003] exynos-gsc 13e30000.gsc: ignoring dependency for device, assuming no driver [ 14.507232] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 14.512486] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.522919] usb3503 usb-hub: switched to HUB mode [ 14.523356] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 14.526252] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 14.538792] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.546935] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 14.552157] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.566635] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 14.631099] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.640377] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.647770] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.727788] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 14.738603] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 14.748790] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 14.753988] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 14.992481] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 15.032742] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.037967] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 15.057103] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 15.066076] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.071288] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 15.207996] hub 1-3:1.0: USB hub found [ 15.212598] hub 1-3:1.0: 3 ports detected [ 15.271171] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.276464] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 15.312956] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.320607] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.329336] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.352946] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.360564] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.369331] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.562881] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 15.663992] random: lvm: uninitialized urandom read (4 bytes read) [ 15.726363] hub 1-3.2:1.0: USB hub found [ 15.729262] hub 1-3.2:1.0: 4 ports detected [ 15.737775] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 15.742986] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 16.052915] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 16.170620] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 16.216004] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 16.743910] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 0a:ff:27:52:60:71 [ 16.745329] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 16.745525] exynos-tmu 10060000.tmu: Failed to register sensor: -517 [ 17.435854] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.487830] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 17.612880] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 18.017421] random: dd: uninitialized urandom read (32 bytes read) [ 19.443373] xenbr0: port 1(eth0) entered blocking state [ 19.447222] xenbr0: port 1(eth0) entered disabled state [ 19.452660] device eth0 entered promiscuous mode [ 19.653395] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.673371] asix 1-3.2.4:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 [ 19.733498] xenbr0: port 1(eth0) entered blocking state [ 19.737351] xenbr0: port 1(eth0) entered forwarding state [ 19.742940] IPv6: ADDRCONF(NETDEV_CHANGE): xenbr0: link becomes ready [ 21.852839] random: crng init done