[ 0.000000] Linux version 6.9.0-rc5+ (osstest@godello0) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Wed Apr 24 00:59:00 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/godello1--vg-root ro console=hvc0 [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009efff] usable [ 0.000000] Xen: [mem 0x000000000009f000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020060fff] usable [ 0.000000] Xen: [mem 0x000000009573f000-0x0000000095bbefff] reserved [ 0.000000] Xen: [mem 0x0000000095bbf000-0x0000000095fbefff] ACPI NVS [ 0.000000] Xen: [mem 0x0000000095fbf000-0x0000000095ffefff] ACPI data [ 0.000000] Xen: [mem 0x0000000096000000-0x000000009fffffff] reserved [ 0.000000] Xen: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved [ 0.000000] Xen: [mem 0x00000000feb00000-0x00000000feb03fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fed10000-0x00000000fed19fff] reserved [ 0.000000] Xen: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] Xen: [mem 0x00000000fed90000-0x00000000fed90fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: Dell Inc. PowerEdge R220/081N4V, BIOS 1.1.4 05/06/2014 [ 0.000000] Hypervisor detected: Xen PV [ 0.000020] Xen PV: Detected 4 vCPUS [ 0.000485] tsc: Detected 3092.836 MHz processor [ 0.000806] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000810] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000817] last_pfn = 0x20061 max_arch_pfn = 0x400000000 [ 0.000822] MTRR map: 4 entries (0 fixed + 4 variable; max 20), built from 10 variable MTRRs [ 0.000824] MTRRs set to read-only [ 0.000829] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.000877] Kernel/User page tables isolation: disabled on XEN PV. [ 0.019997] RAMDISK: [mem 0x04000000-0x053a4fff] [ 0.020012] ACPI: Early table checksum verification disabled [ 0.021580] ACPI: RSDP 0x00000000000FE020 000024 (v02 DELL ) [ 0.021595] ACPI: XSDT 0x0000000095FCF188 0000E4 (v01 DELL PE_SC3 00000001 01000013) [ 0.021660] ACPI: FACP 0x0000000095FF7000 00010C (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.021715] ACPI: DSDT 0x0000000095FDF000 012335 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.021727] ACPI: FACS 0x0000000095FBD000 000040 [ 0.021740] ACPI: UEFI 0x0000000095FFD000 000236 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021755] ACPI: UEFI 0x0000000095FFC000 000042 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.021769] ACPI: ASF! 0x0000000095FFB000 0000A5 (v32 DELL PE_SC3 00000001 DELL 00040000) [ 0.021784] ACPI: ASPT 0x0000000095FFA000 000034 (v07 DELL PE_SC3 00000001 DELL 00040000) [ 0.021797] ACPI: BOOT 0x0000000095FF9000 000028 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021810] ACPI: DBGP 0x0000000095FF8000 000034 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021824] ACPI: HPET 0x0000000095FF6000 000038 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021838] ACPI: APIC 0x0000000095FF5000 000092 (v03 DELL PE_SC3 00000001 DELL 00040000) [ 0.021852] ACPI: MCFG 0x0000000095FF4000 00003C (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021865] ACPI: SLIC 0x0000000095FF3000 000176 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021879] ACPI: SSDT 0x0000000095FDC000 002028 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.021893] ACPI: SPMI 0x0000000095FDA000 000040 (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.021907] ACPI: SSDT 0x0000000095FD9000 000533 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.021920] ACPI: SSDT 0x0000000095FD8000 000ACE (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.021935] ACPI: SSDT 0x0000000095FD4000 003492 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.021949] ACPI: SPCR 0x0000000095FF2000 000050 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021964] ACPI: RMAD 0x0000000095FD3000 000080 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021979] ACPI: SSDT 0x0000000095FD2000 000514 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.021992] ACPI: FPDT 0x0000000095FD1000 000044 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022005] ACPI: HEST 0x0000000095FD0000 0000A8 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022019] ACPI: ERST 0x0000000095FCE000 000230 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022033] ACPI: BERT 0x0000000095FCD000 000030 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022045] ACPI: EINJ 0x0000000095FCC000 000150 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022052] ACPI: Reserving FACP table memory at [mem 0x95ff7000-0x95ff710b] [ 0.022054] ACPI: Reserving DSDT table memory at [mem 0x95fdf000-0x95ff1334] [ 0.022055] ACPI: Reserving FACS table memory at [mem 0x95fbd000-0x95fbd03f] [ 0.022056] ACPI: Reserving UEFI table memory at [mem 0x95ffd000-0x95ffd235] [ 0.022057] ACPI: Reserving UEFI table memory at [mem 0x95ffc000-0x95ffc041] [ 0.022058] ACPI: Reserving ASF! table memory at [mem 0x95ffb000-0x95ffb0a4] [ 0.022058] ACPI: Reserving ASPT table memory at [mem 0x95ffa000-0x95ffa033] [ 0.022059] ACPI: Reserving BOOT table memory at [mem 0x95ff9000-0x95ff9027] [ 0.022060] ACPI: Reserving DBGP table memory at [mem 0x95ff8000-0x95ff8033] [ 0.022061] ACPI: Reserving HPET table memory at [mem 0x95ff6000-0x95ff6037] [ 0.022062] ACPI: Reserving APIC table memory at [mem 0x95ff5000-0x95ff5091] [ 0.022062] ACPI: Reserving MCFG table memory at [mem 0x95ff4000-0x95ff403b] [ 0.022063] ACPI: Reserving SLIC table memory at [mem 0x95ff3000-0x95ff3175] [ 0.022064] ACPI: Reserving SSDT table memory at [mem 0x95fdc000-0x95fde027] [ 0.022065] ACPI: Reserving SPMI table memory at [mem 0x95fda000-0x95fda03f] [ 0.022066] ACPI: Reserving SSDT table memory at [mem 0x95fd9000-0x95fd9532] [ 0.022067] ACPI: Reserving SSDT table memory at [mem 0x95fd8000-0x95fd8acd] [ 0.022068] ACPI: Reserving SSDT table memory at [mem 0x95fd4000-0x95fd7491] [ 0.022069] ACPI: Reserving SPCR table memory at [mem 0x95ff2000-0x95ff204f] [ 0.022069] ACPI: Reserving RMAD table memory at [mem 0x95fd3000-0x95fd307f] [ 0.022070] ACPI: Reserving SSDT table memory at [mem 0x95fd2000-0x95fd2513] [ 0.022071] ACPI: Reserving FPDT table memory at [mem 0x95fd1000-0x95fd1043] [ 0.022072] ACPI: Reserving HEST table memory at [mem 0x95fd0000-0x95fd00a7] [ 0.022073] ACPI: Reserving ERST table memory at [mem 0x95fce000-0x95fce22f] [ 0.022073] ACPI: Reserving BERT table memory at [mem 0x95fcd000-0x95fcd02f] [ 0.022074] ACPI: Reserving EINJ table memory at [mem 0x95fcc000-0x95fcc14f] [ 0.022205] APIC: Switched APIC routing to: Xen PV [ 0.025292] Zone ranges: [ 0.025295] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.025298] DMA32 [mem 0x0000000001000000-0x0000000020060fff] [ 0.025299] Normal empty [ 0.025300] Movable zone start for each node [ 0.025301] Early memory node ranges [ 0.025302] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.025304] node 0: [mem 0x0000000000100000-0x0000000020060fff] [ 0.025306] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020060fff] [ 0.025314] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.025395] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.028708] On node 0, zone DMA32: 32671 pages in unavailable ranges [ 0.028715] p2m virtual area at (____ptrval____), size is 40000000 [ 0.121232] Remapped 97 page(s) [ 0.121767] ACPI: PM-Timer IO Port: 0x1808 [ 0.121838] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.121880] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.121898] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.121903] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.121929] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.121934] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.121944] ACPI: SPCR: SPCR table version 1 [ 0.121947] ACPI: SPCR: console: uart,io,0x3f8,115200 [ 0.121951] CPU topo: 8 possible CPUs exceed the limit of 4 [ 0.121959] CPU topo: Max. logical packages: 1 [ 0.121960] CPU topo: Max. logical dies: 1 [ 0.121961] CPU topo: Max. dies per package: 1 [ 0.121968] CPU topo: Max. threads per core: 1 [ 0.121970] CPU topo: Num. cores per package: 4 [ 0.121970] CPU topo: Num. threads per package: 4 [ 0.121971] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.121988] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.121991] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] [ 0.121994] [mem 0x20061000-0x9573efff] available for PCI devices [ 0.121999] Booting kernel on Xen [ 0.122000] Xen version: 4.19-unstable (preserve-AD) [ 0.122004] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.127945] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.128816] percpu: Embedded 57 pages/cpu s194344 r8192 d30936 u524288 [ 0.128823] pcpu-alloc: s194344 r8192 d30936 u524288 alloc=1*2097152 [ 0.128827] pcpu-alloc: [0] 0 1 2 3 [ 0.128897] xen: PV spinlocks enabled [ 0.128904] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.128908] Kernel command line: placeholder root=/dev/mapper/godello1--vg-root ro console=hvc0 [ 0.128980] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.129004] random: crng init done [ 0.129166] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.129252] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.129845] Built 1 zonelists, mobility grouping on. Total pages: 129006 [ 0.129851] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.129856] software IO TLB: area num 4. [ 0.214774] Memory: 388568K/524284K available (16384K kernel code, 2741K rwdata, 6044K rodata, 2664K init, 1908K bss, 135464K reserved, 0K cma-reserved) [ 0.214921] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.217357] Dynamic Preempt: voluntary [ 0.217490] rcu: Preemptible hierarchical RCU implementation. [ 0.217490] rcu: RCU event tracing is enabled. [ 0.217491] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.217493] Trampoline variant of Tasks RCU enabled. [ 0.217494] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.217495] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.217508] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.225948] NR_IRQS: 4352, nr_irqs: 456, preallocated irqs: 16 [ 0.226101] xen:events: Using FIFO-based ABI [ 0.226129] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.226136] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.226141] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.226147] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.226153] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.226159] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.226164] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.226170] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.226175] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.226183] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.226189] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.226194] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.226200] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.226206] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.226211] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.226222] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.235415] Console: colour VGA+ 80x25 [ 0.235420] printk: legacy console [tty0] enabled [ 0.255926] printk: legacy console [hvc0] enabled [ 0.257024] ACPI: Core revision 20230628 [ 0.276536] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.276741] Xen: using vcpuop timer interface [ 0.276752] installing Xen timer for CPU 0 [ 0.276953] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2c94d83b270, max_idle_ns: 440795286026 ns [ 0.277141] Calibrating delay loop (skipped), value calculated using timer frequency.. 6185.67 BogoMIPS (lpj=3092836) [ 0.277477] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024 [ 0.277615] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4 [ 0.277768] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.278151] Spectre V2 : Mitigation: Retpolines [ 0.278284] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.278452] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.278597] Spectre V2 : Enabling Restricted Speculation for firmware calls [ 0.278738] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.278914] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.279099] MDS: Mitigation: Clear CPU buffers [ 0.279143] MMIO Stale Data: Unknown: No mitigations [ 0.279283] SRBDS: Unknown: Dependent on hypervisor status [ 0.279444] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.279617] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.279761] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.279904] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.280041] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.302280] Freeing SMP alternatives memory: 40K [ 0.302449] pid_max: default: 32768 minimum: 301 [ 0.302618] LSM: initializing lsm=capability,selinux [ 0.302773] SELinux: Initializing. [ 0.302942] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.303118] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.304226] cpu 0 spinlock event irq 25 [ 0.304372] VPMU disabled by hypervisor. [ 0.304869] Performance Events: unsupported p6 CPU model 60 no PMU driver, software events only. [ 0.305049] signal: max sigframe size: 1776 [ 0.305207] rcu: Hierarchical SRCU implementation. [ 0.305347] rcu: Max phase no-delay instances is 400. [ 0.305884] smp: Bringing up secondary CPUs ... [ 0.306228] installing Xen timer for CPU 1 [ 0.306651] installing Xen timer for CPU 2 [ 0.307036] installing Xen timer for CPU 3 [ 0.051912] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0002 [ 0.307226] cpu 1 spinlock event irq 45 [ 0.051912] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0004 [ 0.307509] cpu 2 spinlock event irq 46 [ 0.051912] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0006 [ 0.308188] cpu 3 spinlock event irq 47 [ 0.309179] smp: Brought up 1 node, 4 CPUs [ 0.309544] devtmpfs: initialized [ 0.309544] x86/mm: Memory block size: 128MB [ 0.310258] ACPI: PM: Registering ACPI NVS region [mem 0x95bbf000-0x95fbefff] (4194304 bytes) [ 0.310434] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.310616] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.310877] PM: RTC time: 01:56:41, date: 2024-04-24 [ 0.311252] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.311426] xen:grant_table: Grant tables using version 1 layout [ 0.311583] Grant table initialized [ 0.311863] audit: initializing netlink subsys (disabled) [ 0.312037] audit: type=2000 audit(1713923801.895:1): state=initialized audit_enabled=0 res=1 [ 0.312193] thermal_sys: Registered thermal governor 'step_wise' [ 0.312195] thermal_sys: Registered thermal governor 'user_space' [ 0.312374] Simple Boot Flag at 0x44 set to 0x1 [ 0.312674] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.312991] PCI: ECAM [mem 0xf0000000-0xf7ffffff] (base 0xf0000000) for domain 0000 [bus 00-7f] [ 0.313146] PCI: ECAM [mem 0xf0000000-0xf7ffffff] reserved as E820 entry [ 0.359749] PCI: Using configuration type 1 for base access [ 0.359959] PCI: Dell System detected, enabling pci=bfsort. [ 0.360219] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.361188] ACPI: Added _OSI(Module Device) [ 0.361313] ACPI: Added _OSI(Processor Device) [ 0.361450] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.361588] ACPI: Added _OSI(Processor Aggregator Device) [ 0.372239] ACPI: 6 ACPI AML tables successfully acquired and loaded [ 0.373006] xen: registering gsi 9 triggering 0 polarity 0 [ 0.373565] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.381375] ACPI: Dynamic OEM Table Load: [ 0.381522] ACPI: SSDT 0xFFFF888003598000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120816) [ 0.382388] ACPI: Dynamic OEM Table Load: [ 0.382534] ACPI: SSDT 0xFFFF8880036D4800 0005AA (v01 PmRef ApIst 00003000 INTL 20120816) [ 0.383326] ACPI: Dynamic OEM Table Load: [ 0.383462] ACPI: SSDT 0xFFFF888003568000 000119 (v01 PmRef ApCst 00003000 INTL 20120816) [ 0.384533] ACPI: _OSC evaluated successfully for all CPUs [ 0.384828] ACPI: Interpreter enabled [ 0.384982] ACPI: PM: (supports S0 S4 S5) [ 0.385117] ACPI: Using IOAPIC for interrupt routing [ 0.385166] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.385347] PCI: Using E820 reservations for host bridge windows [ 0.385750] ACPI: Enabled 11 GPEs in block 00 to 3F [ 0.393540] acpi ABCD0000:00: ACPI dock station (docks/bays count: 1) [ 0.401515] ACPI: \_TZ_.FN00: New power resource [ 0.401696] ACPI: \_TZ_.FN01: New power resource [ 0.401871] ACPI: \_TZ_.FN02: New power resource [ 0.402042] ACPI: \_TZ_.FN03: New power resource [ 0.402178] ACPI: \_TZ_.FN04: New power resource [ 0.403026] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e]) [ 0.403144] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.404111] acpi PNP0A08:00: _OSC: OS now controls [PME PCIeCapability LTR] [ 0.404141] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration [ 0.404787] PCI host bridge to bus 0000:00 [ 0.404925] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.405070] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.405142] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.405320] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xfeafffff window] [ 0.405492] pci_bus 0000:00: root bus resource [bus 00-7e] [ 0.405669] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000 conventional PCI endpoint [ 0.406257] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330 conventional PCI endpoint [ 0.406507] pci 0000:00:14.0: BAR 0 [mem 0xa2b00000-0xa2b0ffff 64bit] [ 0.406920] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 0.407299] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320 conventional PCI endpoint [ 0.407531] pci 0000:00:1a.0: BAR 0 [mem 0xa2b12000-0xa2b123ff] [ 0.407984] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 0.408322] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400 PCIe Root Port [ 0.408612] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.408809] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.409208] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.409432] pci 0000:00:1c.0: Enabling MPC IRBNCE [ 0.409576] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled [ 0.410155] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400 PCIe Root Port [ 0.410447] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.410609] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.410792] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.411186] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.411402] pci 0000:00:1c.2: Enabling MPC IRBNCE [ 0.411544] pci 0000:00:1c.2: Intel PCH root port ACS workaround enabled [ 0.412038] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320 conventional PCI endpoint [ 0.412204] pci 0000:00:1d.0: BAR 0 [mem 0xa2b11000-0xa2b113ff] [ 0.412659] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 0.412992] pci 0000:00:1f.0: [8086:8c52] type 00 class 0x060100 conventional PCI endpoint [ 0.413657] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601 conventional PCI endpoint [ 0.413889] pci 0000:00:1f.2: BAR 0 [io 0x3048-0x304f] [ 0.414057] pci 0000:00:1f.2: BAR 1 [io 0x3054-0x3057] [ 0.414176] pci 0000:00:1f.2: BAR 2 [io 0x3040-0x3047] [ 0.414347] pci 0000:00:1f.2: BAR 3 [io 0x3050-0x3053] [ 0.414510] pci 0000:00:1f.2: BAR 4 [io 0x3020-0x303f] [ 0.414678] pci 0000:00:1f.2: BAR 5 [mem 0xa2b10000-0xa2b107ff] [ 0.414983] pci 0000:00:1f.2: PME# supported from D3hot [ 0.415283] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500 conventional PCI endpoint [ 0.415525] pci 0000:00:1f.3: BAR 0 [mem 0xa2b13000-0xa2b130ff 64bit] [ 0.415754] pci 0000:00:1f.3: BAR 4 [io 0x3000-0x301f] [ 0.416356] pci 0000:01:00.0: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.416686] pci 0000:01:00.0: BAR 0 [mem 0xa2a30000-0xa2a3ffff 64bit pref] [ 0.416948] pci 0000:01:00.0: BAR 2 [mem 0xa2a40000-0xa2a4ffff 64bit pref] [ 0.417253] pci 0000:01:00.0: BAR 4 [mem 0xa2a50000-0xa2a5ffff 64bit pref] [ 0.417496] pci 0000:01:00.0: ROM [mem 0x00000000-0x0003ffff pref] [ 0.418063] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.418792] pci 0000:01:00.1: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.419241] pci 0000:01:00.1: BAR 0 [mem 0xa2a00000-0xa2a0ffff 64bit pref] [ 0.419497] pci 0000:01:00.1: BAR 2 [mem 0xa2a10000-0xa2a1ffff 64bit pref] [ 0.419757] pci 0000:01:00.1: BAR 4 [mem 0xa2a20000-0xa2a2ffff 64bit pref] [ 0.419993] pci 0000:01:00.1: ROM [mem 0x00000000-0x0003ffff pref] [ 0.420560] pci 0000:01:00.1: PME# supported from D0 D3hot D3cold [ 0.421333] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.422085] pci 0000:02:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Upstream Port [ 0.423241] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.423605] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.424070] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.425850] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.427368] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.428856] pci 0000:03:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.430244] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.430639] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.431126] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.433088] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold [ 0.434858] pci 0000:03:01.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.436376] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.436789] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.439392] pci 0000:03:01.0: PME# supported from D0 D3hot D3cold [ 0.442804] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.444620] pci 0000:04:00.0: [1912:0012] type 01 class 0x060400 PCIe to PCI/PCI-X bridge [ 0.446009] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.446404] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.446900] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.450259] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.451834] pci_bus 0000:05: extended config space not accessible [ 0.452223] pci 0000:05:00.0: [102b:0534] type 00 class 0x030000 conventional PCI endpoint [ 0.452882] pci 0000:05:00.0: BAR 0 [mem 0xa1000000-0xa1ffffff pref] [ 0.453293] pci 0000:05:00.0: BAR 1 [mem 0xa2800000-0xa2803fff] [ 0.453695] pci 0000:05:00.0: BAR 2 [mem 0xa2000000-0xa27fffff] [ 0.455140] pci 0000:05:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.458606] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.460719] pci 0000:06:00.0: [1912:0011] type 00 class 0x050000 conventional PCI endpoint [ 0.461375] pci 0000:06:00.0: BAR 0 [mem 0xa2901000-0xa2901fff] [ 0.461780] pci 0000:06:00.0: BAR 1 [mem 0xa2900000-0xa290007f] [ 0.464185] pci 0000:06:00.0: PME# supported from D3hot [ 0.465183] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.466694] pci_bus 0000:00: on NUMA node 0 [ 0.466897] xen: registering gsi 13 triggering 1 polarity 0 [ 0.467917] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.468129] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.468212] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.468448] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.468665] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.468807] ACPI: PCI: Interrupt link LNKE disabled [ 0.469008] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.469141] ACPI: PCI: Interrupt link LNKF disabled [ 0.469357] ACPI: PCI: Interrupt link LNKG configured for IRQ 0 [ 0.469500] ACPI: PCI: Interrupt link LNKG disabled [ 0.469708] ACPI: PCI: Interrupt link LNKH configured for IRQ 11 [ 0.470369] xen:balloon: Initialising balloon driver [ 0.470522] iommu: Default domain type: Translated [ 0.470522] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.470526] SCSI subsystem initialized [ 0.471155] libata version 3.00 loaded. [ 0.471175] ACPI: bus type USB registered [ 0.471324] usbcore: registered new interface driver usbfs [ 0.471468] usbcore: registered new interface driver hub [ 0.471612] usbcore: registered new device driver usb [ 0.471763] pps_core: LinuxPPS API ver. 1 registered [ 0.471902] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.472075] PTP clock support registered [ 0.472180] Advanced Linux Sound Architecture Driver Initialized. [ 0.472468] NetLabel: Initializing [ 0.472610] NetLabel: domain hash size = 128 [ 0.472745] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.472897] NetLabel: unlabeled traffic allowed by default [ 0.473168] PCI: Using ACPI for IRQ routing [ 0.489183] PCI: pci_cache_line_size set to 64 bytes [ 0.489818] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] [ 0.489820] e820: reserve RAM buffer [mem 0x20061000-0x23ffffff] [ 0.489840] pci 0000:05:00.0: vgaarb: setting as boot VGA device [ 0.489840] pci 0000:05:00.0: vgaarb: bridge control possible [ 0.489840] pci 0000:05:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.490141] vgaarb: loaded [ 0.490352] clocksource: Switched to clocksource tsc-early [ 0.490550] VFS: Disk quotas dquot_6.6.0 [ 0.490691] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.490848] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.491027] pnp: PnP ACPI init [ 0.491078] system 00:00: [io 0x0680-0x069f] has been reserved [ 0.491225] system 00:00: [io 0xffff] has been reserved [ 0.491364] system 00:00: [io 0xffff] has been reserved [ 0.491505] system 00:00: [io 0xffff] has been reserved [ 0.491645] system 00:00: [io 0x1800-0x18fe] has been reserved [ 0.491788] system 00:00: [io 0x164e-0x164f] has been reserved [ 0.491959] system 00:01: [io 0x0800-0x087f] has been reserved [ 0.491959] xen: registering gsi 8 triggering 1 polarity 0 [ 0.492199] system 00:03: [io 0x1854-0x1857] has been reserved [ 0.492638] xen: registering gsi 3 triggering 1 polarity 0 [ 0.492890] xen: registering gsi 4 triggering 1 polarity 0 [ 0.492893] Already setup the GSI :4 [ 0.493202] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.493350] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved [ 0.493494] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.493638] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.493780] system 00:06: [mem 0xf0000000-0xf7ffffff] has been reserved [ 0.493924] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved [ 0.494070] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved [ 0.494220] system 00:06: [mem 0xff000000-0xffffffff] could not be reserved [ 0.494366] system 00:06: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.494510] system 00:06: [mem 0xa0000000-0xa0000fff] has been reserved [ 0.494654] system 00:06: [mem 0xa0020000-0xa002ffff] has been reserved [ 0.495643] pnp: PnP ACPI: found 7 devices [ 0.515807] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.515998] NET: Registered PF_INET protocol family [ 0.516171] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.516494] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.516672] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.516841] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.517020] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.517223] TCP: Hash tables configured (established 4096 bind 4096) [ 0.517395] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.517559] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.517727] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.518040] RPC: Registered named UNIX socket transport module. [ 0.518193] RPC: Registered udp transport module. [ 0.518407] RPC: Registered tcp transport module. [ 0.518550] RPC: Registered tcp-with-tls transport module. [ 0.518691] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.519125] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff]: assigned [ 0.519311] pci 0000:01:00.0: ROM [mem 0xa0100000-0xa013ffff pref]: assigned [ 0.519459] pci 0000:01:00.1: ROM [mem 0xa0140000-0xa017ffff pref]: assigned [ 0.519606] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.519758] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff] [ 0.519912] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.520106] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.520398] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.520635] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.521002] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.521296] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.521535] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.521915] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.522208] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.522707] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.522987] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.523221] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.523634] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.523785] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.523939] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.524131] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.524282] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.524426] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.524564] pci_bus 0000:00: resource 7 [mem 0xa0000000-0xfeafffff window] [ 0.524715] pci_bus 0000:01: resource 1 [mem 0xa0100000-0xa01fffff] [ 0.524859] pci_bus 0000:01: resource 2 [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.525024] pci_bus 0000:02: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.525173] pci_bus 0000:02: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.525338] pci_bus 0000:03: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.525481] pci_bus 0000:03: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.525650] pci_bus 0000:04: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.525787] pci_bus 0000:04: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.525960] pci_bus 0000:05: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.526098] pci_bus 0000:05: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.526280] pci_bus 0000:06: resource 1 [mem 0xa2900000-0xa29fffff] [ 0.526541] xen: registering gsi 16 triggering 0 polarity 1 [ 0.526560] xen: --> pirq=16 -> irq=16 (gsi=16) [ 0.527998] xen: registering gsi 16 triggering 0 polarity 1 [ 0.528002] Already setup the GSI :16 [ 0.540256] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x7c0 took 12017 usecs [ 0.540505] xen: registering gsi 23 triggering 0 polarity 1 [ 0.540526] xen: --> pirq=23 -> irq=23 (gsi=23) [ 0.552268] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x7c0 took 11534 usecs [ 0.552749] PCI: CLS 64 bytes, default 64 [ 0.552898] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.552945] Unpacking initramfs... [ 0.553037] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 0.555373] kvm_intel: VMX not supported by CPU 0 [ 0.555516] kvm_amd: CPU 0 isn't AMD or Hygon [ 0.555655] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c94d83b270, max_idle_ns: 440795286026 ns [ 0.556348] clocksource: Switched to clocksource tsc [ 0.558669] Initialise system trusted keyrings [ 0.558901] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 0.559179] NFS: Registering the id_resolver key type [ 0.559325] Key type id_resolver registered [ 0.559461] Key type id_legacy registered [ 0.559640] 9p: Installing v9fs 9p2000 file system support [ 0.572051] Key type asymmetric registered [ 0.572198] Asymmetric key parser 'x509' registered [ 0.572353] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.572534] io scheduler mq-deadline registered [ 0.572674] io scheduler kyber registered [ 0.573165] xen: registering gsi 16 triggering 0 polarity 1 [ 0.573172] Already setup the GSI :16 [ 0.573516] pcieport 0000:00:1c.0: PME: Signaling with IRQ 50 [ 0.573883] xen: registering gsi 18 triggering 0 polarity 1 [ 0.573899] xen: --> pirq=18 -> irq=18 (gsi=18) [ 0.574090] pcieport 0000:00:1c.2: PME: Signaling with IRQ 51 [ 0.578482] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.578715] ACPI: button: Power Button [PWRF] [ 0.579233] Monitor-Mwait will be used to enter C-1 state [ 0.579243] Monitor-Mwait will be used to enter C-2 state [ 0.579248] ACPI: \_PR_.CPU0: Found 2 idle states [ 0.579564] ACPI: \_PR_.CPU1: Found 2 idle states [ 0.579935] ACPI: \_PR_.CPU2: Found 2 idle states [ 0.580437] ACPI: \_PR_.CPU3: Found 2 idle states [ 0.581000] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.581145] ACPI: thermal: Thermal Zone [TZ00] (28 C) [ 0.581503] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.581648] ACPI: thermal: Thermal Zone [TZ01] (30 C) [ 0.582009] xen:xen_evtchn: Event-channel device installed [ 0.582234] xen_pciback: backend is vpci [ 0.582785] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.583076] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 0.583785] hpet_acpi_add: no address or irqs in _CRS [ 0.583988] Non-volatile memory driver v1.3 [ 0.585340] loop: module loaded [ 0.588893] ahci 0000:00:1f.2: version 3.0 [ 0.589003] xen: registering gsi 19 triggering 0 polarity 1 [ 0.589027] xen: --> pirq=19 -> irq=19 (gsi=19) [ 0.589199] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled [ 0.589374] ahci 0000:00:1f.2: AHCI vers 0001.0300, 32 command slots, 6 Gbps, SATA mode [ 0.589624] ahci 0000:00:1f.2: 3/6 ports implemented (port mask 0x31) [ 0.589767] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst [ 0.596406] scsi host0: ahci [ 0.596738] scsi host1: ahci [ 0.597016] scsi host2: ahci [ 0.597278] scsi host3: ahci [ 0.597532] scsi host4: ahci [ 0.597783] scsi host5: ahci [ 0.597962] ata1: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10100 irq 53 lpm-pol 0 [ 0.598140] ata2: DUMMY [ 0.598268] ata3: DUMMY [ 0.598397] ata4: DUMMY [ 0.598523] ata5: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10300 irq 53 lpm-pol 0 [ 0.598698] ata6: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10380 irq 53 lpm-pol 0 [ 0.599062] tun: Universal TUN/TAP device driver, 1.6 [ 0.599394] xen: registering gsi 16 triggering 0 polarity 1 [ 0.599400] Already setup the GSI :16 [ 0.630546] Freeing initrd memory: 20116K [ 0.633616] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:88 [ 0.633805] tg3 0000:01:00.0 eth0: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.633994] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.634168] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.634716] xen: registering gsi 17 triggering 0 polarity 1 [ 0.634740] xen: --> pirq=17 -> irq=17 (gsi=17) [ 0.682389] tg3 0000:01:00.1 eth1: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:8a [ 0.682575] tg3 0000:01:00.1 eth1: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.682754] tg3 0000:01:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.682936] tg3 0000:01:00.1 eth1: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.683381] e100: Intel(R) PRO/100 Network Driver [ 0.683520] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.683671] sky2: driver version 1.30 [ 0.683827] xen_netfront: Initialising Xen virtual ethernet driver [ 0.684259] xen: registering gsi 16 triggering 0 polarity 1 [ 0.684265] Already setup the GSI :16 [ 0.684289] xen: registering gsi 16 triggering 0 polarity 1 [ 0.684322] xen: registering gsi 23 triggering 0 polarity 1 [ 0.684325] Already setup the GSI :23 [ 0.684384] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 0.684461] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.684535] Already setup the GSI :16 [ 0.684571] ehci-pci 0000:00:1d.0: debug port 2 [ 0.689124] ehci-pci 0000:00:1d.0: irq 23, io mem 0xa2b11000 [ 0.695936] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 0.696152] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.09 [ 0.696326] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.696499] usb usb1: Product: EHCI Host Controller [ 0.696639] usb usb1: Manufacturer: Linux 6.9.0-rc5+ ehci_hcd [ 0.696781] usb usb1: SerialNumber: 0000:00:1d.0 [ 0.697118] hub 1-0:1.0: USB hub found [ 0.697272] hub 1-0:1.0: 2 ports detected [ 0.697604] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 0.697842] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 2 [ 0.698062] ehci-pci 0000:00:1a.0: debug port 2 [ 0.702210] ehci-pci 0000:00:1a.0: irq 16, io mem 0xa2b12000 [ 0.708982] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 0.709186] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.09 [ 0.709357] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.709529] usb usb2: Product: EHCI Host Controller [ 0.709671] usb usb2: Manufacturer: Linux 6.9.0-rc5+ ehci_hcd [ 0.709824] usb usb2: SerialNumber: 0000:00:1a.0 [ 0.710148] hub 2-0:1.0: USB hub found [ 0.710299] hub 2-0:1.0: 2 ports detected [ 0.710604] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.710817] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 0.712088] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810 [ 0.712527] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.712775] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 0.712961] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [ 0.713197] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.09 [ 0.713377] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.713550] usb usb3: Product: xHCI Host Controller [ 0.713690] usb usb3: Manufacturer: Linux 6.9.0-rc5+ xhci-hcd [ 0.713834] usb usb3: SerialNumber: 0000:00:14.0 [ 0.714178] hub 3-0:1.0: USB hub found [ 0.714351] hub 3-0:1.0: 10 ports detected [ 0.717665] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.09 [ 0.717852] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.718037] usb usb4: Product: xHCI Host Controller [ 0.718178] usb usb4: Manufacturer: Linux 6.9.0-rc5+ xhci-hcd [ 0.718322] usb usb4: SerialNumber: 0000:00:14.0 [ 0.718637] hub 4-0:1.0: USB hub found [ 0.718789] hub 4-0:1.0: 2 ports detected [ 0.719334] usbcore: registered new interface driver usblp [ 0.719486] usbcore: registered new interface driver usb-storage [ 0.719646] i8042: PNP: No PS/2 controller found. [ 0.719884] rtc_cmos 00:02: RTC can wake from S4 [ 0.720497] rtc_cmos 00:02: registered as rtc0 [ 0.720684] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram [ 0.720853] device-mapper: uevent: version 1.0.3 [ 0.720938] xen: registering gsi 18 triggering 0 polarity 1 [ 0.720995] Already setup the GSI :18 [ 0.721070] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 0.721224] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 0.721308] intel_pstate: CPU model not supported [ 0.721587] hid: raw HID events driver (C) Jiri Kosina [ 0.721821] usbcore: registered new interface driver usbhid [ 0.721973] usbhid: USB HID core driver [ 0.722368] Initializing XFRM netlink socket [ 0.722519] NET: Registered PF_INET6 protocol family [ 0.722972] Segment Routing with IPv6 [ 0.723123] In-situ OAM (IOAM) with IPv6 [ 0.723289] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.723562] NET: Registered PF_PACKET protocol family [ 0.723764] 9pnet: Installing 9P2000 support [ 0.723923] Key type dns_resolver registered [ 0.724291] IPI shorthand broadcast: enabled [ 0.726490] sched_clock: Marking stable (675003585, 50912029)->(735644730, -9729116) [ 0.726541] i2c i2c-0: Successfully instantiated SPD at 0x51 [ 0.727005] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.727263] registered taskstats version 1 [ 0.727402] Loading compiled-in X.509 certificates [ 0.728591] PM: Magic number: 4:784:913 [ 0.728793] printk: legacy console [netcon0] enabled [ 0.728943] netconsole: network logging started [ 0.729272] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 0.737556] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 0.737895] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 0.740059] ALSA device list: [ 0.740196] No soundcards found. [ 0.740783] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 0.907304] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.935020] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 0.950980] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 0.955260] ata1.00: ATA-8: TOSHIBA MG03ACA100, FL1D, max UDMA/100 [ 0.956151] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.957520] ata1.00: configured for UDMA/100 [ 0.957791] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MG03ACA1 FL1D PQ: 0 ANSI: 5 [ 0.958289] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 0.958290] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 0.958330] sd 0:0:0:0: [sda] Write Protect is off [ 0.958727] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 0.958767] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.959017] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 0.959926] usb 3-9: new high-speed USB device number 2 using xhci_hcd [ 1.063674] usb 1-1: New USB device found, idVendor=8087, idProduct=8000, bcdDevice= 0.05 [ 1.063844] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.064305] hub 1-1:1.0: USB hub found [ 1.064598] hub 1-1:1.0: 6 ports detected [ 1.079662] usb 2-1: New USB device found, idVendor=8087, idProduct=8008, bcdDevice= 0.05 [ 1.079828] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.080324] hub 2-1:1.0: USB hub found [ 1.080586] hub 2-1:1.0: 4 ports detected [ 1.086684] usb 3-9: New USB device found, idVendor=0624, idProduct=0248, bcdDevice= 0.00 [ 1.086850] usb 3-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.087007] usb 3-9: Product: Gadget USB HUB [ 1.087131] usb 3-9: Manufacturer: no manufacturer [ 1.087264] usb 3-9: SerialNumber: 0123456789 [ 1.088246] hub 3-9:1.0: USB hub found [ 1.088482] hub 3-9:1.0: 6 ports detected [ 1.145961] sda: sda1 sda2 < sda5 > [ 1.146445] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.267252] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.270116] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GTA0N, A3B0, max UDMA/100 [ 1.275026] ata5.00: configured for UDMA/100 [ 1.280120] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW GTA0N A3B0 PQ: 0 ANSI: 5 [ 1.309431] sr 4:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.309614] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.322398] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 1.322482] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 1.383021] usb 3-9.1: new high-speed USB device number 3 using xhci_hcd [ 1.469988] usb 3-9.1: New USB device found, idVendor=0624, idProduct=0249, bcdDevice= 0.00 [ 1.470169] usb 3-9.1: New USB device strings: Mfr=4, Product=5, SerialNumber=6 [ 1.470344] usb 3-9.1: Product: Keyboard/Mouse Function [ 1.470488] usb 3-9.1: Manufacturer: Avocent [ 1.470625] usb 3-9.1: SerialNumber: 20120917 [ 1.477501] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.0/0003:0624:0249.0001/input/input1 [ 1.529201] hid-generic 0003:0624:0249.0001: input,hidraw0: USB HID v1.00 Keyboard [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input0 [ 1.530177] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.1/0003:0624:0249.0002/input/input2 [ 1.530578] hid-generic 0003:0624:0249.0002: input,hidraw1: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input1 [ 1.531560] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.2/0003:0624:0249.0003/input/input3 [ 1.531875] hid-generic 0003:0624:0249.0003: input,hidraw2: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input2 [ 1.627024] ata6: SATA link down (SStatus 0 SControl 300) [ 1.628426] Freeing unused kernel image (initmem) memory: 2664K [ 1.628574] Write protecting the kernel read-only data: 22528k [ 1.640624] Freeing unused kernel image (rodata/data gap) memory: 100K [ 1.844802] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.845000] Run /init as init process [ 1.845141] with arguments: [ 1.845142] /init [ 1.845143] placeholder [ 1.845143] with environment: [ 1.845144] HOME=/ [ 1.845145] TERM=linux [ 2.070757] tg3 0000:01:00.1 enx549f3505fd8a: renamed from eth1 [ 2.073170] tg3 0000:01:00.0 enx549f3505fd88: renamed from eth0 [ 2.778726] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.012641] EXT4-fs (dm-0): mounted filesystem 232edbbe-eb0b-4be1-89bb-d33bba68a4e8 ro with ordered data mode. Quota mode: none. [ 6.559872] EXT4-fs (dm-0): re-mounted 232edbbe-eb0b-4be1-89bb-d33bba68a4e8 r/w. Quota mode: none. [ 7.329059] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 7.339754] EXT4-fs (sda1): mounted filesystem 84a0108c-7d4a-4442-80c0-9ca5503cafef r/w with ordered data mode. Quota mode: none. [ 7.396757] Adding 1949692k swap on /dev/mapper/godello1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 8.927358] xenbr0: port 1(enx549f3505fd88) entered blocking state [ 8.927543] xenbr0: port 1(enx549f3505fd88) entered disabled state [ 8.927694] tg3 0000:01:00.0 enx549f3505fd88: entered allmulticast mode [ 8.927869] tg3 0000:01:00.0 enx549f3505fd88: entered promiscuous mode [ 12.635533] tg3 0000:01:00.0 enx549f3505fd88: Link is up at 1000 Mbps, full duplex [ 12.635786] tg3 0000:01:00.0 enx549f3505fd88: Flow control is off for TX and off for RX [ 12.635962] tg3 0000:01:00.0 enx549f3505fd88: EEE is disabled [ 12.636190] xenbr0: port 1(enx549f3505fd88) entered blocking state [ 12.636336] xenbr0: port 1(enx549f3505fd88) entered forwarding state