[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.9.0-rc5+ (osstest@godello0) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Wed Apr 24 01:10:36 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41364 r8192 d24172 u73728 [ 0.000000] pcpu-alloc: s41364 r8192 d24172 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414612K/524288K available (15360K kernel code, 2252K rwdata, 5964K rodata, 2048K init, 438K bss, 44140K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000512] Console: colour dummy device 80x30 [ 0.000530] printk: legacy console [hvc0] enabled [ 0.299007] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309405] CPU: Testing write buffer coherency: ok [ 0.314347] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.323901] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330332] pid_max: default: 32768 minimum: 301 [ 0.335099] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342382] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350785] /cpus/cpu@0 missing clock-frequency property [ 0.355585] /cpus/cpu@1 missing clock-frequency property [ 0.360980] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367652] xen:grant_table: Grant tables using version 1 layout [ 0.372837] Grant table initialized [ 0.376376] xen:events: Using FIFO-based ABI [ 0.380689] Xen: initializing cpu0 [ 0.384219] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.391960] rcu: Hierarchical SRCU implementation. [ 0.395606] rcu: Max phase no-delay instances is 1000. [ 0.403758] EFI services will not be available. [ 0.407080] smp: Bringing up secondary CPUs ... [ 0.481699] Xen: initializing cpu1 [ 0.481864] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481888] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500823] smp: Brought up 1 node, 2 CPUs [ 0.504513] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510826] CPU: All CPU(s) started in SVC mode. [ 0.516741] devtmpfs: initialized [ 0.529001] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535522] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545229] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553154] pinctrl core: initialized pinctrl subsystem [ 0.559701] DMI not present or invalid. [ 0.563219] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569863] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579113] thermal_sys: Registered thermal governor 'step_wise' [ 0.579276] software IO TLB: area num 2. [ 0.587943] software IO TLB: only able to allocate 8 MB [ 0.595010] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600198] No ATAGs? [ 0.602531] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611196] Serial: AMBA PL011 UART driver [ 0.657939] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686382] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.709717] xen:balloon: Initialising balloon driver [ 0.716138] iommu: Default domain type: Translated [ 0.719551] iommu: DMA domain TLB invalidation policy: strict mode [ 0.728319] SCSI subsystem initialized [ 0.730879] libata version 3.00 loaded. [ 0.731088] usbcore: registered new interface driver usbfs [ 0.736299] usbcore: registered new interface driver hub [ 0.741662] usbcore: registered new device driver usb [ 0.748316] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.751906] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.758155] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.763216] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.768151] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.774191] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.779958] pps_core: LinuxPPS API ver. 1 registered [ 0.784365] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.793589] PTP clock support registered [ 0.797807] EDAC MC: Ver: 3.0.0 [ 0.801383] scmi_core: SCMI protocol bus registered [ 0.807895] vgaarb: loaded [ 0.811226] clocksource: Switched to clocksource arch_sys_counter [ 0.825248] NET: Registered PF_INET protocol family [ 0.828889] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.836825] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.844486] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.852291] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.860117] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.867414] TCP: Hash tables configured (established 4096 bind 4096) [ 0.873775] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.880328] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.887454] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.893600] RPC: Registered named UNIX socket transport module. [ 0.899063] RPC: Registered udp transport module. [ 0.903852] RPC: Registered tcp transport module. [ 0.908611] RPC: Registered tcp-with-tls transport module. [ 0.914179] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.920699] PCI: CLS 0 bytes, default 64 [ 0.926108] Initialise system trusted keyrings [ 0.929413] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.935954] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.941880] Trying to unpack rootfs image as initramfs... [ 0.972844] NFS: Registering the id_resolver key type [ 0.976584] Key type id_resolver registered [ 0.980806] Key type id_legacy registered [ 0.984930] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.991674] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.012630] Key type asymmetric registered [ 1.015361] Asymmetric key parser 'x509' registered [ 1.020364] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.027786] io scheduler mq-deadline registered [ 1.032400] io scheduler kyber registered [ 1.036472] io scheduler bfq registered [ 1.192030] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.198244] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.239850] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.246143] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.282669] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.288885] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.321999] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.328204] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.340529] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.401719] xen:xen_evtchn: Event-channel device installed [ 1.550403] Freeing initrd memory: 11868K [ 1.656480] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.667560] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.675787] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.684670] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.693669] SuperH (H)SCI(F) driver initialized [ 1.697958] STMicroelectronics ASC driver initialized [ 1.702844] STM32 USART driver initialized [ 1.709003] random: crng init done [ 1.711048] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.726847] brd: module loaded [ 1.732854] loop: module loaded [ 1.756449] Invalid max_queues (4), will use default max: 2. [ 1.775011] tun: Universal TUN/TAP device driver, 1.6 [ 1.778866] CAN device driver interface [ 1.784101] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.795157] xen_netfront: Initialising Xen virtual ethernet driver [ 1.800003] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.805635] usbcore: registered new interface driver pegasus [ 1.811366] usbcore: registered new interface driver asix [ 1.816817] usbcore: registered new interface driver ax88179_178a [ 1.822993] usbcore: registered new interface driver cdc_ether [ 1.828882] usbcore: registered new interface driver smsc75xx [ 1.834717] usbcore: registered new interface driver smsc95xx [ 1.840513] usbcore: registered new interface driver net1080 [ 1.846251] usbcore: registered new interface driver cdc_subset [ 1.852262] usbcore: registered new interface driver zaurus [ 1.857875] usbcore: registered new interface driver cdc_ncm [ 1.867228] usbcore: registered new interface driver usb-storage [ 1.877780] i2c_dev: i2c /dev entries driver [ 1.896356] device-mapper: uevent: version 1.0.3 [ 1.899779] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.909417] cpu cpu0: OPP table can't be empty [ 1.914138] failed to register cpuidle driver [ 1.917481] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.925828] sdhci: Secure Digital Host Controller Interface driver [ 1.930847] sdhci: Copyright(c) Pierre Ossman [ 1.938880] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.946643] ledtrig-cpu: registered to indicate activity on CPUs [ 1.952117] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.958726] usbcore: registered new interface driver usbhid [ 1.963471] usbhid: USB HID core driver [ 1.974128] NET: Registered PF_INET6 protocol family [ 1.978680] Segment Routing with IPv6 [ 1.981535] In-situ OAM (IOAM) with IPv6 [ 1.985509] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.992088] NET: Registered PF_PACKET protocol family [ 1.996563] can: controller area network core [ 2.001012] NET: Registered PF_CAN protocol family [ 2.005891] can: raw protocol [ 2.008883] can: broadcast manager protocol [ 2.013184] can: netlink gateway - max_hops=1 [ 2.017871] Key type dns_resolver registered [ 2.022616] ThumbEE CPU extension supported. [ 2.026247] Registering SWP/SWPB emulation handler [ 2.040396] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.047314] Loading compiled-in X.509 certificates [ 2.090438] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.094111] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.101539] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.109062] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.157818] s5m-rtc s5m-rtc: registered as rtc0 [ 2.166670] s5m-rtc s5m-rtc: setting system clock to 2000-01-02T00:00:26 UTC (946771226) [ 2.177592] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.182286] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.186572] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.193386] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.200028] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.206111] clk: Not disabling unused clocks [ 2.209701] PM: genpd: Disabling unused power domains [ 2.218243] Freeing unused kernel image (initmem) memory: 2048K [ 2.224533] Run /init as init process [ 2.226816] with arguments: [ 2.226822] /init [ 2.226828] with environment: [ 2.226834] HOME=/ [ 2.226839] TERM=linux [ 3.485554] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.615471] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.626578] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.723513] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.734573] Synopsys Designware Multimedia Card Interface Driver [ 3.764544] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.770157] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.796859] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.810117] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.824841] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.830450] exynos-ohci 12120000.usb: USB Host Controller [ 3.835977] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.844046] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.891918] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.902297] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.940675] hub 1-0:1.0: USB hub found [ 3.943894] hub 1-0:1.0: 3 ports detected [ 3.966717] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.973026] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.988970] hub 2-0:1.0: USB hub found [ 3.991419] hub 2-0:1.0: 3 ports detected [ 3.991605] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.997371] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 4.017752] VDD_ALIVE_1.0V: Bringing 1000000uV into 1100000-1100000uV [ 4.023538] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 4.023902] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.030318] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 4.044243] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 4.051054] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 4.138995] scsi host0: ahci-dwc [ 4.152802] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 127 lpm-pol 0 [ 4.180936] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.185617] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.195520] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.200621] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.206199] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 128,32 bit host data width,128 deep fifo [ 4.216000] mmc_host mmc0: card is polling. [ 4.220259] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.226478] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.231988] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 129,32 bit host data width,128 deep fifo [ 4.242886] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.254443] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.344794] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.353459] mmc1: new high speed SDHC card at address aaaa [ 4.359803] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.365937] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.374903] mmc0: new DDR MMC card at address 0001 [ 4.380081] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.389556] mmcblk0: p1 p2 p3 p4 [ 4.396445] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.402633] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.410160] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.671393] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.677727] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.683123] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.691576] ata1.00: configured for UDMA/133 [ 4.694874] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.706203] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.712372] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.718519] sd 0:0:0:0: [sda] Write Protect is off [ 4.722526] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.723290] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.732474] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.757940] sda: sda1 sda2 < sda5 > [ 4.760697] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.823157] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.852162] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.856691] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.900041] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.908288] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.914369] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.919728] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.927481] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.937189] hub 3-0:1.0: USB hub found [ 4.939670] hub 3-0:1.0: 1 port detected [ 4.951340] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.966172] hub 4-0:1.0: USB hub found [ 4.969209] hub 4-0:1.0: 1 port detected [ 10.061553] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 10.372236] EXT4-fs (dm-0): mounted filesystem 1ae08b5e-c913-42b7-b7d3-382e09eb027d ro with ordered data mode. Quota mode: disabled. [ 14.346460] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 14.350844] s5p-secss 10830000.sss: s5p-sss driver registered [ 14.430815] mc: Linux media interface: v0.10 [ 14.620935] videodev: Linux video capture interface: v2.00 [ 14.929410] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 14.961435] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 14.981662] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 14.990360] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 15.001739] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 15.025901] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 15.156559] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.187504] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 15.191262] usb3503 usb-hub: switched to HUB mode [ 15.196413] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.200195] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 15.257161] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.275745] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.283125] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.294493] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 15.323484] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 15.541356] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 15.752707] hub 1-3:1.0: USB hub found [ 15.760584] hub 1-3:1.0: 3 ports detected [ 15.817583] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.825373] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.834006] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.845930] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.853610] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.862337] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.091261] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.244073] hub 1-3.2:1.0: USB hub found [ 16.247106] hub 1-3.2:1.0: 4 ports detected [ 16.307949] usbcore: registered new device driver onboard-usb-hub [ 16.442040] hub 1-3.2:1.0: USB hub found [ 16.444971] hub 1-3.2:1.0: 4 ports detected [ 16.458746] hub 1-3.2:1.0: USB hub found [ 16.461705] hub 1-3.2:1.0: 4 ports detected [ 16.801278] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 16.943926] EXT4-fs (dm-0): re-mounted 1ae08b5e-c913-42b7-b7d3-382e09eb027d r/w. Quota mode: disabled. [ 16.965433] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.683342] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 17.687585] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 17.688204] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 66:cb:7e:2e:1f:85 [ 18.564708] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.605406] EXT4-fs (sda1): mounted filesystem 40ee9b74-402e-4f77-964c-8d9298395ce7 r/w with ordered data mode. Quota mode: disabled. [ 18.713042] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 20.499012] xenbr0: port 1(eth0) entered blocking state [ 20.502929] xenbr0: port 1(eth0) entered disabled state [ 20.508185] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 20.514107] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 20.524795] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 22.728554] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 22.734616] xenbr0: port 1(eth0) entered blocking state [ 22.739795] xenbr0: port 1(eth0) entered forwarding state