[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-20-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.85-1 (2024-04-11) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015528K/2097152K available (12288K kernel code, 1714K rwdata, 3744K rodata, 2048K init, 382K bss, 65240K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39967 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000018] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002618] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002632] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002646] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002658] Ignoring duplicate/late registration of read_current_timer delay [ 0.003021] Console: colour dummy device 80x30 [ 0.003061] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003075] CPU: Testing write buffer coherency: ok [ 0.003116] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003124] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003130] pid_max: default: 32768 minimum: 301 [ 0.003490] LSM: Security Framework initializing [ 0.003562] landlock: Up and running. [ 0.003567] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003755] AppArmor: AppArmor initialized [ 0.003767] TOMOYO Linux initialized [ 0.003810] LSM support for eBPF active [ 0.004061] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004075] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005486] /cpus/cpu@0 missing clock-frequency property [ 0.005513] /cpus/cpu@1 missing clock-frequency property [ 0.005527] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006480] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006487] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006591] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006597] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006737] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007892] rcu: Hierarchical SRCU implementation. [ 0.007898] rcu: Max phase no-delay instances is 1000. [ 0.010003] EFI services will not be available. [ 0.010350] smp: Bringing up secondary CPUs ... [ 0.011093] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011104] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011233] smp: Brought up 1 node, 2 CPUs [ 0.011241] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011249] CPU: All CPU(s) started in HYP mode. [ 0.011253] CPU: Virtualization extensions available. [ 0.012124] devtmpfs: initialized [ 0.023491] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023730] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023754] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024296] pinctrl core: initialized pinctrl subsystem [ 0.025027] DMI not present or invalid. [ 0.025710] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027275] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028813] audit: initializing netlink subsys (disabled) [ 0.029019] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030208] thermal_sys: Registered thermal governor 'fair_share' [ 0.030216] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030221] thermal_sys: Registered thermal governor 'step_wise' [ 0.030225] thermal_sys: Registered thermal governor 'user_space' [ 0.030229] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030431] No ATAGs? [ 0.030499] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030507] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031593] Serial: AMBA PL011 UART driver [ 0.081012] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.088039] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091815] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091823] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.098687] iommu: Default domain type: Translated [ 0.098696] iommu: DMA domain TLB invalidation policy: strict mode [ 0.099680] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100215] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100226] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.100865] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.100896] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101100] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.101456] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.101466] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.101853] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102139] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102149] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.102445] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.102563] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.102572] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.102755] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.102970] pps_core: LinuxPPS API ver. 1 registered [ 0.102975] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.102990] PTP clock support registered [ 0.104501] NetLabel: Initializing [ 0.104508] NetLabel: domain hash size = 128 [ 0.104513] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.104568] NetLabel: unlabeled traffic allowed by default [ 0.104741] vgaarb: loaded [ 0.105706] clocksource: Switched to clocksource mct-frc [ 0.106283] VFS: Disk quotas dquot_6.6.0 [ 0.106367] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107182] AppArmor: AppArmor Filesystem Enabled [ 0.117192] NET: Registered PF_INET protocol family [ 0.117383] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.119036] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.119139] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.119163] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119262] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119493] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119732] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.119833] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119874] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120090] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.120129] NET: Registered PF_XDP protocol family [ 0.120140] PCI: CLS 0 bytes, default 64 [ 0.120640] Trying to unpack rootfs image as initramfs... [ 0.120992] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126399] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.191621] Initialise system trusted keyrings [ 0.191703] Key type blacklist registered [ 0.192919] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.201171] zbud: loaded [ 0.202465] integrity: Platform Keyring initialized [ 0.202508] integrity: Machine keyring initialized [ 0.202518] Key type asymmetric registered [ 0.202527] Asymmetric key parser 'x509' registered [ 1.422312] Freeing initrd memory: 25112K [ 1.444524] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.444796] bounce: pool size: 64 pages [ 1.444978] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.445146] io scheduler mq-deadline registered [ 1.450358] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.471372] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.471383] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473774] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473784] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.474606] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474615] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.475445] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.475453] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.477805] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.480585] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.483377] Serial: AMBA driver [ 1.483602] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.484084] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.484576] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.565384] printk: console [ttySAC2] enabled [ 2.570203] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.580851] STM32 USART driver initialized [ 2.595297] mousedev: PS/2 mouse device common for all mice [ 2.626475] s5m-rtc s5m-rtc: registered as rtc0 [ 2.635078] s5m-rtc s5m-rtc: setting system clock to 2024-04-24T19:33:29 UTC (1713987209) [ 2.644903] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.652348] ledtrig-cpu: registered to indicate activity on CPUs [ 2.660400] NET: Registered PF_INET6 protocol family [ 2.684609] Segment Routing with IPv6 [ 2.686877] In-situ OAM (IOAM) with IPv6 [ 2.690835] mip6: Mobile IPv6 [ 2.693672] NET: Registered PF_PACKET protocol family [ 2.698875] mpls_gso: MPLS GSO support [ 2.702899] ThumbEE CPU extension supported. [ 2.706711] Registering SWP/SWPB emulation handler [ 2.711967] registered taskstats version 1 [ 2.715586] Loading compiled-in X.509 certificates [ 3.174547] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.181883] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.192962] zswap: loaded using pool lzo/zbud [ 3.196881] Key type .fscrypt registered [ 3.200222] Key type fscrypt-provisioning registered [ 3.224456] Key type encrypted registered [ 3.227034] AppArmor: AppArmor sha1 policy hashing enabled [ 3.232544] ima: No TPM chip found, activating TPM-bypass! [ 3.237997] ima: Allocated hash algorithm: sha256 [ 3.242700] ima: No architecture policies found [ 3.247243] evm: Initialising EVM extended attributes: [ 3.252286] evm: security.selinux [ 3.255577] evm: security.SMACK64 (disabled) [ 3.259824] evm: security.SMACK64EXEC (disabled) [ 3.264425] evm: security.SMACK64TRANSMUTE (disabled) [ 3.269459] evm: security.SMACK64MMAP (disabled) [ 3.274059] evm: security.apparmor [ 3.277430] evm: security.ima [ 3.280395] evm: security.capability [ 3.283960] evm: HMAC attrs: 0x1 [ 3.871209] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.896901] Freeing unused kernel image (initmem) memory: 2048K [ 3.901786] Checked W+X mappings: passed, no W+X pages found [ 3.907022] Run /init as init process [ 3.910655] with arguments: [ 3.910663] /init [ 3.910669] with environment: [ 3.910675] HOME=/ [ 3.910680] TERM=linux [ 4.830268] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.891398] usbcore: registered new interface driver usbfs [ 4.900849] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.913302] Synopsys Designware Multimedia Card Interface Driver [ 4.924300] usbcore: registered new interface driver hub [ 4.928433] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.937115] usbcore: registered new device driver usb [ 4.946406] phy phy-12130000.phy.1: phy_power_on was called before phy_init [ 4.957767] phy phy-12130000.phy.1: phy_power_on was called before phy_init [ 4.962550] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.963490] exynos-ohci 12120000.usb: USB Host Controller [ 4.982399] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 4.982511] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 5.000119] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.024268] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 5.036727] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 5.041767] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 5.047208] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 5.053548] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.062427] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.067068] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.070184] SCSI subsystem initialized [ 5.077114] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 5.080970] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.111956] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.120093] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.134306] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.141150] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.148367] usb usb1: Product: USB Host Controller [ 5.153115] usb usb1: Manufacturer: Linux 6.1.0-20-armmp-lpae ohci_hcd [ 5.159616] usb usb1: SerialNumber: 12120000.usb [ 5.166437] mmc_host mmc0: card is polling. [ 5.182514] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.192445] hub 1-0:1.0: USB hub found [ 5.195982] hub 1-0:1.0: 3 ports detected [ 5.197938] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.209847] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.216691] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.223874] usb usb2: Product: EHCI Host Controller [ 5.228726] usb usb2: Manufacturer: Linux 6.1.0-20-armmp-lpae ehci_hcd [ 5.235247] usb usb2: SerialNumber: 12110000.usb [ 5.243483] hub 2-0:1.0: USB hub found [ 5.245932] hub 2-0:1.0: 3 ports detected [ 5.267611] libata version 3.00 loaded. [ 5.289770] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.298842] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.316411] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.324775] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.333696] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.345523] mmc1: new high speed SDHC card at address aaaa [ 5.346731] mmc0: new DDR MMC card at address 0001 [ 5.365078] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.366007] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.370777] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.383995] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.394155] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.405268] mmcblk0: p1 p2 p3 p4 [ 5.409192] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.417891] scsi host0: ahci-dwc [ 5.425222] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.436511] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.442959] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.897111] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.905747] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.912138] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.917989] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.925443] ata1.00: configured for UDMA/133 [ 5.929185] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.967335] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.986152] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.990229] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.998376] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.007243] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.013458] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.018676] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.026320] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.033228] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.041074] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.048256] usb usb3: Product: xHCI Host Controller [ 6.053119] usb usb3: Manufacturer: Linux 6.1.0-20-armmp-lpae xhci-hcd [ 6.059623] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.066328] hub 3-0:1.0: USB hub found [ 6.068670] hub 3-0:1.0: 1 port detected [ 6.074297] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.081062] I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.090514] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.098580] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.105768] usb usb4: Product: xHCI Host Controller [ 6.110628] usb usb4: Manufacturer: Linux 6.1.0-20-armmp-lpae xhci-hcd [ 6.117146] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.123907] hub 4-0:1.0: USB hub found [ 6.126280] hub 4-0:1.0: 1 port detected [ 6.127190] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.137600] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.146575] sd 0:0:0:0: [sda] Write Protect is off [ 6.149934] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.150018] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.159058] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.190426] I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.198414] sda: sda1 sda2 < sda5 > [ 6.202668] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.298485] I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.406530] I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.514591] I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.622665] I/O error, dev mmcblk1, sector 7744005 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.740033] I/O error, dev mmcblk1, sector 7744007 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.862012] I/O error, dev mmcblk1, sector 7744010 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 6.979332] I/O error, dev mmcblk1, sector 7744012 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 7.087354] I/O error, dev mmcblk1, sector 7744013 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 7.221729] random: crng init done [ 7.330736] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.341559] device-mapper: uevent: version 1.0.3 [ 7.346297] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 8.524970] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 8.599241] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 8.960433] Buffer I/O error on dev mmcblk1, logical block 968001, async page read [ 12.095650] PM: Image not found (code -22) [ 12.631746] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.889265] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 13.203183] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 16.721552] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 16.779601] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 16.936258] panfrost 11800000.gpu: clock rate = 533000000 [ 16.945918] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 17.037808] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 17.044108] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 17.052339] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 17.064002] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 17.077950] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 17.113744] usb3503 usb-hub: switched to HUB mode [ 17.116986] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 17.209018] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 17.279289] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.387884] blk_print_req_error: 14 callbacks suppressed [ 17.387912] I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.437900] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 17.501457] I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.609939] I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.622863] usb 2-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 17.630229] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 17.651060] hub 2-3:1.0: USB hub found [ 17.653939] hub 2-3:1.0: 3 ports detected [ 17.718233] I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.756711] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 17.768033] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 17.826736] OF: graph: no port node found in /soc/hdmi@14530000 [ 17.836915] I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.838176] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 17.852607] exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm]) [ 17.861349] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm]) [ 17.873449] exynos-drm exynos-drm: bound 14500000.dsi (ops exynos_dsi_component_ops [exynosdrm]) [ 17.881164] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops [exynosdrm]) [ 17.890464] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 17.896468] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 17.903268] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1 [ 17.973792] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 18.009842] I/O error, dev mmcblk1, sector 7744013 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 18.100374] usb 2-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 18.107450] usb 2-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 18.115022] usb 2-3.2: Product: USB2.0 Hub [ 18.119029] I/O error, dev mmcblk1, sector 7744014 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 18.137044] hub 2-3.2:1.0: USB hub found [ 18.140166] hub 2-3.2:1.0: 4 ports detected [ 18.228383] I/O error, dev mmcblk1, sector 7744015 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 18.336631] I/O error, dev mmcblk1, sector 7744016 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 2 [ 18.433806] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 18.444883] I/O error, dev mmcblk1, sector 7744017 op 0x0:(READ) flags 0x80700 phys_seg 12 prio class 2 [ 18.556118] usb 2-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 18.563814] usb 2-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 18.570822] usb 2-3.2.4: Product: AX88772 [ 18.575278] usb 2-3.2.4: Manufacturer: ASIX Elec. Corp. [ 18.580101] usb 2-3.2.4: SerialNumber: 000001 [ 19.089230] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 19.828343] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 19.843898] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 19.855834] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 1e:1c:76:1d:22:7e [ 19.866490] usbcore: registered new interface driver asix [ 20.466210] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 21.048535] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 23.504772] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 23.567988] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 23.824546] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 25.093554] audit: type=1400 audit(1713987231.420:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=903 comm="apparmor_parser" [ 25.138858] audit: type=1400 audit(1713987231.468:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=904 comm="apparmor_parser" [ 25.153233] audit: type=1400 audit(1713987231.480:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=904 comm="apparmor_parser" [ 25.350011] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 25.529490] audit: type=1400 audit(1713987231.856:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=944 comm="apparmor_parser" [ 25.548520] audit: type=1400 audit(1713987231.872:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=944 comm="apparmor_parser" [ 25.561943] audit: type=1400 audit(1713987231.876:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=944 comm="apparmor_parser" [ 25.773075] audit: type=1400 audit(1713987232.100:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=937 comm="apparmor_parser" [ 25.789688] audit: type=1400 audit(1713987232.104:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=937 comm="apparmor_parser" [ 25.806796] audit: type=1400 audit(1713987232.108:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=937 comm="apparmor_parser" [ 25.824331] audit: type=1400 audit(1713987232.116:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=937 comm="apparmor_parser" [ 27.495782] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 27.501844] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready