[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-20-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.85-1 (2024-04-11) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015528K/2097152K available (12288K kernel code, 1714K rwdata, 3744K rodata, 2048K init, 382K bss, 65240K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39967 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000018] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002621] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002636] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002651] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002662] Ignoring duplicate/late registration of read_current_timer delay [ 0.003025] Console: colour dummy device 80x30 [ 0.003065] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003079] CPU: Testing write buffer coherency: ok [ 0.003118] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003127] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003133] pid_max: default: 32768 minimum: 301 [ 0.003494] LSM: Security Framework initializing [ 0.003565] landlock: Up and running. [ 0.003570] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003758] AppArmor: AppArmor initialized [ 0.003771] TOMOYO Linux initialized [ 0.003817] LSM support for eBPF active [ 0.004064] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004079] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005480] /cpus/cpu@0 missing clock-frequency property [ 0.005509] /cpus/cpu@1 missing clock-frequency property [ 0.005523] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006481] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006488] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006592] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006598] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006738] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007900] rcu: Hierarchical SRCU implementation. [ 0.007905] rcu: Max phase no-delay instances is 1000. [ 0.010027] EFI services will not be available. [ 0.010373] smp: Bringing up secondary CPUs ... [ 0.011113] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011124] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011257] smp: Brought up 1 node, 2 CPUs [ 0.011266] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011274] CPU: All CPU(s) started in HYP mode. [ 0.011278] CPU: Virtualization extensions available. [ 0.012136] devtmpfs: initialized [ 0.023497] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023736] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023760] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024317] pinctrl core: initialized pinctrl subsystem [ 0.025043] DMI not present or invalid. [ 0.025722] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027277] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028804] audit: initializing netlink subsys (disabled) [ 0.029009] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030191] thermal_sys: Registered thermal governor 'fair_share' [ 0.030198] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030203] thermal_sys: Registered thermal governor 'step_wise' [ 0.030208] thermal_sys: Registered thermal governor 'user_space' [ 0.030212] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030414] No ATAGs? [ 0.030480] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030489] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031578] Serial: AMBA PL011 UART driver [ 0.081005] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.088031] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091821] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091829] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.098681] iommu: Default domain type: Translated [ 0.098690] iommu: DMA domain TLB invalidation policy: strict mode [ 0.099660] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100196] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100207] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.100852] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.100882] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101087] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.101444] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.101455] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.101844] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102134] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102144] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.102444] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.102563] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.102572] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.102756] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.102972] pps_core: LinuxPPS API ver. 1 registered [ 0.102977] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.102993] PTP clock support registered [ 0.104538] NetLabel: Initializing [ 0.104544] NetLabel: domain hash size = 128 [ 0.104549] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.104603] NetLabel: unlabeled traffic allowed by default [ 0.104777] vgaarb: loaded [ 0.105810] clocksource: Switched to clocksource mct-frc [ 0.106384] VFS: Disk quotas dquot_6.6.0 [ 0.106468] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107278] AppArmor: AppArmor Filesystem Enabled [ 0.117417] NET: Registered PF_INET protocol family [ 0.117608] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.119085] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.119185] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.119210] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119312] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119543] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119784] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.119876] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119918] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120128] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.120165] NET: Registered PF_XDP protocol family [ 0.120176] PCI: CLS 0 bytes, default 64 [ 0.120691] Trying to unpack rootfs image as initramfs... [ 0.121034] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126571] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.191309] Initialise system trusted keyrings [ 0.191433] Key type blacklist registered [ 0.192639] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.200852] zbud: loaded [ 0.202263] integrity: Platform Keyring initialized [ 0.202325] integrity: Machine keyring initialized [ 0.202334] Key type asymmetric registered [ 0.202340] Asymmetric key parser 'x509' registered [ 1.421416] Freeing initrd memory: 25112K [ 1.443818] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.444087] bounce: pool size: 64 pages [ 1.444267] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.444433] io scheduler mq-deadline registered [ 1.449539] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.470500] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.470511] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.472881] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.472891] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473694] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473704] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.474578] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474588] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.476900] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.479730] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.482536] Serial: AMBA driver [ 1.482761] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.483245] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.483714] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.564532] printk: console [ttySAC2] enabled [ 2.569365] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.580014] STM32 USART driver initialized [ 2.594448] mousedev: PS/2 mouse device common for all mice [ 2.625627] s5m-rtc s5m-rtc: registered as rtc0 [ 2.634257] s5m-rtc s5m-rtc: setting system clock to 2024-04-24T23:01:53 UTC (1713999713) [ 2.644112] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.651555] ledtrig-cpu: registered to indicate activity on CPUs [ 2.659610] NET: Registered PF_INET6 protocol family [ 2.683809] Segment Routing with IPv6 [ 2.686108] In-situ OAM (IOAM) with IPv6 [ 2.690003] mip6: Mobile IPv6 [ 2.692869] NET: Registered PF_PACKET protocol family [ 2.698055] mpls_gso: MPLS GSO support [ 2.702087] ThumbEE CPU extension supported. [ 2.705901] Registering SWP/SWPB emulation handler [ 2.711137] registered taskstats version 1 [ 2.714773] Loading compiled-in X.509 certificates [ 3.174456] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.181779] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.192845] zswap: loaded using pool lzo/zbud [ 3.196808] Key type .fscrypt registered [ 3.200104] Key type fscrypt-provisioning registered [ 3.224296] Key type encrypted registered [ 3.226889] AppArmor: AppArmor sha1 policy hashing enabled [ 3.232345] ima: No TPM chip found, activating TPM-bypass! [ 3.237831] ima: Allocated hash algorithm: sha256 [ 3.242552] ima: No architecture policies found [ 3.247041] evm: Initialising EVM extended attributes: [ 3.252115] evm: security.selinux [ 3.255404] evm: security.SMACK64 (disabled) [ 3.259655] evm: security.SMACK64EXEC (disabled) [ 3.264254] evm: security.SMACK64TRANSMUTE (disabled) [ 3.269289] evm: security.SMACK64MMAP (disabled) [ 3.273890] evm: security.apparmor [ 3.277260] evm: security.ima [ 3.280226] evm: security.capability [ 3.283790] evm: HMAC attrs: 0x1 [ 3.870826] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.896444] Freeing unused kernel image (initmem) memory: 2048K [ 3.901319] Checked W+X mappings: passed, no W+X pages found [ 3.906564] Run /init as init process [ 3.910198] with arguments: [ 3.910205] /init [ 3.910212] with environment: [ 3.910218] HOME=/ [ 3.910223] TERM=linux [ 4.847404] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.855927] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.872529] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.880378] Synopsys Designware Multimedia Card Interface Driver [ 4.891264] usbcore: registered new interface driver usbfs [ 4.911852] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.911988] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.925267] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.930575] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.937222] usbcore: registered new interface driver hub [ 4.941511] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.947687] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.968026] usbcore: registered new device driver usb [ 4.989951] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107,32 bit host data width,128 deep fifo [ 5.001799] SCSI subsystem initialized [ 5.011560] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.026762] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.042313] mmc_host mmc0: card is polling. [ 5.060559] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.068461] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.122254] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 5.129236] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 5.134943] exynos-ohci 12120000.usb: USB Host Controller [ 5.140446] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 5.158013] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.177465] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 5.184295] exynos-ohci 12120000.usb: irq 109, io mem 0x12120000 [ 5.190044] libata version 3.00 loaded. [ 5.196219] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.202238] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.204835] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.212743] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.232816] mmc0: new DDR MMC card at address 0001 [ 5.245425] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.253319] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.256485] mmc1: new high speed SDHC card at address aaaa [ 5.262283] exynos-ehci 12110000.usb: irq 109, io mem 0x12110000 [ 5.265987] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.268950] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.276126] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.281879] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.287744] usb usb1: Product: USB Host Controller [ 5.298502] usb usb1: Manufacturer: Linux 6.1.0-20-armmp-lpae ohci_hcd [ 5.305003] usb usb1: SerialNumber: 12120000.usb [ 5.313557] mmcblk0: p1 p2 p3 p4 [ 5.320033] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.325669] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.334521] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.349722] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.368662] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.375466] scsi host0: ahci-dwc [ 5.380564] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.398180] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.440048] hub 1-0:1.0: USB hub found [ 5.442675] hub 1-0:1.0: 3 ports detected [ 5.447897] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.454764] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.461933] usb usb2: Product: EHCI Host Controller [ 5.466779] usb usb2: Manufacturer: Linux 6.1.0-20-armmp-lpae ehci_hcd [ 5.473294] usb usb2: SerialNumber: 12110000.usb [ 5.499755] hub 2-0:1.0: USB hub found [ 5.502215] hub 2-0:1.0: 3 ports detected [ 5.861883] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.867452] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.873303] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.880748] ata1.00: configured for UDMA/133 [ 5.884542] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.905174] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.974078] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.978186] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.986994] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 5.995224] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.001463] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.006834] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.014290] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 6.024061] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.030826] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.038741] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.045931] usb usb3: Product: xHCI Host Controller [ 6.050782] usb usb3: Manufacturer: Linux 6.1.0-20-armmp-lpae xhci-hcd [ 6.057300] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.062847] hub 3-0:1.0: USB hub found [ 6.065930] hub 3-0:1.0: 1 port detected [ 6.070366] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.078262] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.085454] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.090660] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.098801] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.098833] sd 0:0:0:0: [sda] Write Protect is off [ 6.105977] usb usb4: Product: xHCI Host Controller [ 6.105984] usb usb4: Manufacturer: Linux 6.1.0-20-armmp-lpae xhci-hcd [ 6.105991] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.106987] hub 4-0:1.0: USB hub found [ 6.110756] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.115653] hub 4-0:1.0: 1 port detected [ 6.122797] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.127161] I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.130844] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.183161] sda: sda1 sda2 < sda5 > [ 6.186715] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.234703] I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.342766] I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.450808] I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.558845] I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.666893] I/O error, dev mmcblk1, sector 7744005 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.774935] I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.882976] I/O error, dev mmcblk1, sector 7744007 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 6.991013] I/O error, dev mmcblk1, sector 7744008 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 7.112324] I/O error, dev mmcblk1, sector 7744010 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 7.201834] random: crng init done [ 7.311136] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.322014] device-mapper: uevent: version 1.0.3 [ 7.329876] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 9.534599] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 12.655215] PM: Image not found (code -22) [ 13.211317] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 13.491327] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 13.839694] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 17.405343] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 17.484677] panfrost 11800000.gpu: clock rate = 533000000 [ 17.506508] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 17.527068] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 17.639261] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 17.645620] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 17.653723] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 17.665439] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 17.760459] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 17.762028] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 17.831463] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.859898] usb3503 usb-hub: switched to HUB mode [ 17.863199] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 17.941261] blk_print_req_error: 20 callbacks suppressed [ 17.941278] I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.059402] I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.167588] I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.193929] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 18.244215] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 18.253733] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 18.275719] I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.314992] OF: graph: no port node found in /soc/hdmi@14530000 [ 18.322837] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 18.329053] exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm]) [ 18.337545] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm]) [ 18.351304] exynos-drm exynos-drm: bound 14500000.dsi (ops exynos_dsi_component_ops [exynosdrm]) [ 18.359096] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops [exynosdrm]) [ 18.367347] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 18.374173] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 18.375579] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1 [ 18.380871] usb 2-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 18.395383] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 18.402958] I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.413427] hub 2-3:1.0: USB hub found [ 18.418626] hub 2-3:1.0: 3 ports detected [ 18.527140] I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.635621] I/O error, dev mmcblk1, sector 7744007 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 18.741857] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 18.776088] I/O error, dev mmcblk1, sector 7744012 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 18.865583] usb 2-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 18.872655] usb 2-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 18.879922] usb 2-3.2: Product: USB2.0 Hub [ 18.884243] I/O error, dev mmcblk1, sector 7744013 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 18.896384] hub 2-3.2:1.0: USB hub found [ 18.899496] hub 2-3.2:1.0: 4 ports detected [ 19.006063] I/O error, dev mmcblk1, sector 7744015 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 19.198402] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 19.312703] usb 2-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 19.320228] usb 2-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 19.327508] usb 2-3.2.4: Product: AX88772 [ 19.331485] usb 2-3.2.4: Manufacturer: ASIX Elec. Corp. [ 19.336672] usb 2-3.2.4: SerialNumber: 000001 [ 19.739745] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 20.416495] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 20.432541] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 20.446424] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 52:df:11:fe:74:b6 [ 20.458817] usbcore: registered new interface driver asix [ 21.239133] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 21.828432] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 23.862445] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 23.914364] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 24.093162] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 25.443497] audit: type=1400 audit(1713999735.452:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=899 comm="apparmor_parser" [ 25.460142] audit: type=1400 audit(1713999735.456:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=899 comm="apparmor_parser" [ 25.475823] audit: type=1400 audit(1713999735.468:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=898 comm="apparmor_parser" [ 25.642161] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 25.841995] audit: type=1400 audit(1713999735.852:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=941 comm="apparmor_parser" [ 25.861122] audit: type=1400 audit(1713999735.868:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=941 comm="apparmor_parser" [ 25.874566] audit: type=1400 audit(1713999735.868:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=941 comm="apparmor_parser" [ 26.184776] audit: type=1400 audit(1713999736.192:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=940 comm="apparmor_parser" [ 26.201565] audit: type=1400 audit(1713999736.196:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=940 comm="apparmor_parser" [ 26.218551] audit: type=1400 audit(1713999736.200:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=940 comm="apparmor_parser" [ 26.243168] audit: type=1400 audit(1713999736.252:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=940 comm="apparmor_parser" [ 27.783811] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 27.789911] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready