[ 0.000000] Linux version 6.10.0-rc2+ (osstest@himrod2) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Fri Jun 7 02:15:07 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000095fff] usable [ 0.000000] Xen: [mem 0x0000000000096000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020069fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SCM/H8SCM, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000013] Xen PV: Detected 6 vCPUS [ 0.037156] tsc: Fast TSC calibration using PIT [ 0.037158] tsc: Detected 3101.258 MHz processor [ 0.037160] tsc: Detected 3101.136 MHz TSC [ 0.037370] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.037374] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.037381] last_pfn = 0x2006a max_arch_pfn = 0x400000000 [ 0.037386] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.037388] MTRRs set to read-only [ 0.037392] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.062152] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.062179] ACPI: Early table checksum verification disabled [ 0.063686] ACPI: RSDP 0x00000000000FA1D0 000024 (v02 ACPIAM) [ 0.063699] ACPI: XSDT 0x00000000DFEA0100 000084 (v01 SMCI 20131125 MSFT 00000097) [ 0.063743] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.063806] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.063819] ACPI: DSDT 0x00000000DFEA0600 005699 (v01 1BA11 1BA11000 00000000 INTL 20051117) [ 0.063829] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.063839] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.063850] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.063862] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.063873] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.063884] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.063894] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.063906] ACPI: SRAT 0x00000000DFEAA6F0 000108 (v02 AMD AGESA 00000001 AMD 00000001) [ 0.063916] ACPI: SSDT 0x00000000DFEAA800 001158 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.063927] ACPI: EINJ 0x00000000DFEAB960 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.063938] ACPI: BERT 0x00000000DFEABAF0 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.063949] ACPI: ERST 0x00000000DFEABB20 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.063960] ACPI: HEST 0x00000000DFEABD30 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.063965] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.063967] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c98] [ 0.063969] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.063970] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.063971] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.063973] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.063974] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.063975] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.063976] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.063977] ACPI: Reserving SRAT table memory at [mem 0xdfeaa6f0-0xdfeaa7f7] [ 0.063979] ACPI: Reserving SSDT table memory at [mem 0xdfeaa800-0xdfeab957] [ 0.063980] ACPI: Reserving EINJ table memory at [mem 0xdfeab960-0xdfeaba8f] [ 0.063981] ACPI: Reserving BERT table memory at [mem 0xdfeabaf0-0xdfeabb1f] [ 0.063983] ACPI: Reserving ERST table memory at [mem 0xdfeabb20-0xdfeabd2f] [ 0.063984] ACPI: Reserving HEST table memory at [mem 0xdfeabd30-0xdfeabdd7] [ 0.064120] APIC: Switched APIC routing to: Xen PV [ 0.066415] Zone ranges: [ 0.066417] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.066420] DMA32 [mem 0x0000000001000000-0x0000000020069fff] [ 0.066422] Normal empty [ 0.066423] Movable zone start for each node [ 0.066424] Early memory node ranges [ 0.066425] node 0: [mem 0x0000000000001000-0x0000000000095fff] [ 0.066427] node 0: [mem 0x0000000000100000-0x0000000020069fff] [ 0.066430] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020069fff] [ 0.066446] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.066579] On node 0, zone DMA: 106 pages in unavailable ranges [ 0.072306] On node 0, zone DMA32: 32662 pages in unavailable ranges [ 0.072327] p2m virtual area at (____ptrval____), size is 40000000 [ 0.279812] Remapped 106 page(s) [ 0.280334] ACPI: PM-Timer IO Port: 0x808 [ 0.280378] CPU topo: CPU limit of 6 reached. Ignoring further CPUs [ 0.280414] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.280418] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.280443] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.280452] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.280466] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.280472] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.280499] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.280504] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.280518] CPU topo: Max. logical packages: 1 [ 0.280519] CPU topo: Max. logical dies: 1 [ 0.280520] CPU topo: Max. dies per package: 1 [ 0.280529] CPU topo: Max. threads per core: 1 [ 0.280531] CPU topo: Num. cores per package: 6 [ 0.280532] CPU topo: Num. threads per package: 6 [ 0.280532] CPU topo: Allowing 6 present CPUs plus 0 hotplug CPUs [ 0.280534] CPU topo: Rejected CPUs 2 [ 0.280555] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.280558] PM: hibernation: Registered nosave memory: [mem 0x00096000-0x000fffff] [ 0.280561] [mem 0x2006a000-0xdfe9dfff] available for PCI devices [ 0.280566] Booting kernel on Xen [ 0.280568] Xen version: 4.19-unstable (preserve-AD) [ 0.280573] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.286939] setup_percpu: NR_CPUS:64 nr_cpumask_bits:6 nr_cpu_ids:6 nr_node_ids:1 [ 0.288276] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u262144 [ 0.288288] pcpu-alloc: s194408 r8192 d30872 u262144 alloc=1*2097152 [ 0.288293] pcpu-alloc: [0] 0 1 2 3 4 5 - - [ 0.288392] xen: PV spinlocks enabled [ 0.288397] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.288401] Kernel command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.288500] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.288569] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.288710] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.288972] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.288979] mem auto-init: stack:all(zero), heap alloc:off, heap free:off, mlocked free:off [ 0.288983] software IO TLB: area num 8. [ 0.428401] Memory: 385988K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 138044K reserved, 0K cma-reserved) [ 0.428551] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.431723] Dynamic Preempt: voluntary [ 0.431872] rcu: Preemptible hierarchical RCU implementation. [ 0.431874] rcu: RCU event tracing is enabled. [ 0.431875] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.431878] Trampoline variant of Tasks RCU enabled. [ 0.431880] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.431881] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 [ 0.431908] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.438644] NR_IRQS: 4352, nr_irqs: 1016, preallocated irqs: 16 [ 0.438838] xen:events: Using FIFO-based ABI [ 0.438878] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.438885] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.438890] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.438895] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.438900] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.438905] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.438910] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.438915] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.438920] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.438924] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.438930] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.438935] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.438939] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.438948] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.438953] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.438968] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.445027] Console: colour VGA+ 80x25 [ 0.445032] printk: legacy console [tty0] enabled [ 0.458613] printk: legacy console [hvc0] enabled [ 0.459265] ACPI: Core revision 20240322 [ 0.465022] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.465179] Xen: using vcpuop timer interface [ 0.465186] installing Xen timer for CPU 0 [ 0.465440] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cb378b39e7, max_idle_ns: 440795289550 ns [ 0.465640] Calibrating delay loop (skipped), value calculated using timer frequency.. 6202.27 BogoMIPS (lpj=3101136) [ 0.465834] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.466050] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.466158] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.466274] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.466655] Spectre V2 : Mitigation: Retpolines [ 0.466758] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.466901] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.467012] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.467123] RETBleed: Mitigation: untrained return thunk [ 0.467267] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.467412] Speculative Store Bypass: Vulnerable [ 0.467545] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.467643] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.467753] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.467864] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.467973] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.496151] Freeing SMP alternatives memory: 40K [ 0.496311] pid_max: default: 32768 minimum: 301 [ 0.496471] LSM: initializing lsm=capability,selinux [ 0.496596] SELinux: Initializing. [ 0.496709] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.496857] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.497784] cpu 0 spinlock event irq 57 [ 0.497898] VPMU disabled by hypervisor. [ 0.498392] Performance Events: PMU not available due to virtualization, using software events only. [ 0.498646] signal: max sigframe size: 1776 [ 0.498814] rcu: Hierarchical SRCU implementation. [ 0.498925] rcu: Max phase no-delay instances is 400. [ 0.505082] smp: Bringing up secondary CPUs ... [ 0.505421] installing Xen timer for CPU 1 [ 0.505953] installing Xen timer for CPU 2 [ 0.506401] installing Xen timer for CPU 3 [ 0.506831] installing Xen timer for CPU 4 [ 0.507323] installing Xen timer for CPU 5 [ 0.027661] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.507874] cpu 1 spinlock event irq 87 [ 0.027661] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.508727] cpu 2 spinlock event irq 88 [ 0.027661] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.508985] cpu 3 spinlock event irq 89 [ 0.027661] [Firmware Bug]: CPU 4: APIC ID mismatch. CPUID: 0x0004 APIC: 0x0014 [ 0.509755] cpu 4 spinlock event irq 90 [ 0.027661] [Firmware Bug]: CPU 5: APIC ID mismatch. CPUID: 0x0005 APIC: 0x0015 [ 0.510745] cpu 5 spinlock event irq 91 [ 0.511124] smp: Brought up 1 node, 6 CPUs [ 0.512013] devtmpfs: initialized [ 0.512013] x86/mm: Memory block size: 128MB [ 0.513207] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.513207] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.513655] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.513930] PM: RTC time: 02:35:48, date: 2024-06-07 [ 0.514311] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.514469] xen:grant_table: Grant tables using version 1 layout [ 0.514650] Grant table initialized [ 0.515072] audit: initializing netlink subsys (disabled) [ 0.515246] audit: type=2000 audit(1717727748.541:1): state=initialized audit_enabled=0 res=1 [ 0.515668] thermal_sys: Registered thermal governor 'step_wise' [ 0.515672] thermal_sys: Registered thermal governor 'user_space' [ 0.515955] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.516645] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.753943] PCI: Using configuration type 1 for base access [ 0.754337] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.754795] ACPI: Added _OSI(Module Device) [ 0.754831] ACPI: Added _OSI(Processor Device) [ 0.755641] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.755755] ACPI: Added _OSI(Processor Aggregator Device) [ 0.774660] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.779050] xen: registering gsi 9 triggering 0 polarity 1 [ 0.788703] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.789119] ACPI: Interpreter enabled [ 0.789248] ACPI: PM: (supports S0 S1 S4 S5) [ 0.789355] ACPI: Using IOAPIC for interrupt routing [ 0.789536] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.789640] PCI: Using E820 reservations for host bridge windows [ 0.789917] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.801917] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.802038] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.802195] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.802307] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.802452] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.802922] PCI host bridge to bus 0000:00 [ 0.803025] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.803138] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.803254] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.803399] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.803544] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.803641] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.803800] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.804352] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.804864] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.805076] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.805194] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.805309] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.805469] pci 0000:00:09.0: enabling Extended Tags [ 0.805700] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.805990] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.806199] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.806317] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.806430] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.806593] pci 0000:00:0a.0: enabling Extended Tags [ 0.806755] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.807058] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601 conventional PCI endpoint [ 0.807285] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.807414] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.807543] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.807663] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.807791] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.807919] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.808267] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.808455] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.808874] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.809063] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.809453] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.809650] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.809986] pci 0000:00:12.2: supports D1 D2 [ 0.810093] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.810354] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.810541] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.810906] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.811091] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.811493] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.811682] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.812009] pci 0000:00:13.2: supports D1 D2 [ 0.812117] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.812400] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.812938] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.813129] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.813259] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.813390] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.813520] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.813657] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.813819] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.813932] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.814044] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.814170] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.814476] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.814986] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.815238] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.815365] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.815493] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.815773] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.815961] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.816362] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.816749] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.817089] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.817399] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.817757] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.818158] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.818621] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.818691] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.818855] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.818988] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.819348] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.822699] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.823035] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.823230] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.823393] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.823533] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.823913] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.826684] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.826855] pci_bus 0000:03: extended config space not accessible [ 0.827033] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.827228] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.827666] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.827839] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.828090] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.828517] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.828648] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.828793] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.828939] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.829086] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.829270] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.829494] pci_bus 0000:00: on NUMA node 0 [ 0.830150] xen: registering gsi 13 triggering 1 polarity 0 [ 0.830674] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.830867] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.831061] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.831247] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.831447] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.831642] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.831834] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.832021] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.832306] xen:balloon: Initialising balloon driver [ 0.833243] iommu: Default domain type: Translated [ 0.833525] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.834153] SCSI subsystem initialized [ 0.834465] libata version 3.00 loaded. [ 0.834465] ACPI: bus type USB registered [ 0.834664] usbcore: registered new interface driver usbfs [ 0.834784] usbcore: registered new interface driver hub [ 0.834899] usbcore: registered new device driver usb [ 0.835029] pps_core: LinuxPPS API ver. 1 registered [ 0.835134] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.835297] PTP clock support registered [ 0.835959] Advanced Linux Sound Architecture Driver Initialized. [ 0.838406] NetLabel: Initializing [ 0.838663] NetLabel: domain hash size = 128 [ 0.838978] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.839383] NetLabel: unlabeled traffic allowed by default [ 0.839867] PCI: Using ACPI for IRQ routing [ 0.881934] PCI: pci_cache_line_size set to 64 bytes [ 0.882135] e820: reserve RAM buffer [mem 0x00096000-0x0009ffff] [ 0.882144] e820: reserve RAM buffer [mem 0x2006a000-0x23ffffff] [ 0.882248] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.882248] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.882248] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.882642] vgaarb: loaded [ 0.885879] clocksource: Switched to clocksource tsc-early [ 0.886510] VFS: Disk quotas dquot_6.6.0 [ 0.886630] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.886684] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.886866] pnp: PnP ACPI init [ 0.887362] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.887657] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.888210] xen: registering gsi 8 triggering 1 polarity 0 [ 0.888485] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.888845] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.888967] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.889509] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.889626] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.889751] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.889865] system 00:05: [io 0x040b] has been reserved [ 0.889978] system 00:05: [io 0x04d6] has been reserved [ 0.890091] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.890206] system 00:05: [io 0x0c14] has been reserved [ 0.890318] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.890436] system 00:05: [io 0x0c52] has been reserved [ 0.890548] system 00:05: [io 0x0c6c] has been reserved [ 0.890669] system 00:05: [io 0x0c6f] has been reserved [ 0.890780] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.890896] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.891026] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.891141] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.891257] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.891371] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.891486] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.891601] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.891724] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.891840] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.891955] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.892070] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.892187] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.892344] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.892779] xen: registering gsi 4 triggering 1 polarity 0 [ 0.892783] Already setup the GSI :4 [ 0.892889] pnp 00:06: [dma 0 disabled] [ 0.893253] xen: registering gsi 3 triggering 1 polarity 0 [ 0.893260] pnp 00:07: [dma 0 disabled] [ 0.893448] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.893938] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.894138] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.894257] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.894376] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.894495] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.894803] pnp: PnP ACPI: found 10 devices [ 0.916928] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.917136] NET: Registered PF_INET protocol family [ 0.917375] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.917860] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.918019] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.918171] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.918339] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.918553] TCP: Hash tables configured (established 4096 bind 4096) [ 0.918786] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.918943] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.919128] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.919523] RPC: Registered named UNIX socket transport module. [ 0.919651] RPC: Registered udp transport module. [ 0.919760] RPC: Registered tcp transport module. [ 0.919869] RPC: Registered tcp-with-tls transport module. [ 0.919985] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.920764] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.920893] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.921025] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.921166] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.921289] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.921433] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.921574] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.921707] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.921836] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.922007] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.922126] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.922247] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.922369] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.922489] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.922610] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.922747] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.922872] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.922982] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.923095] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.923211] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.923329] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.923445] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.923560] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.923687] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.923805] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.924131] xen: registering gsi 16 triggering 0 polarity 1 [ 0.924194] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.574838] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 635553 usecs [ 1.575130] xen: registering gsi 16 triggering 0 polarity 1 [ 1.575147] Already setup the GSI :16 [ 1.599839] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 24193 usecs [ 1.600096] xen: registering gsi 17 triggering 0 polarity 1 [ 1.600201] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.600409] xen: registering gsi 18 triggering 0 polarity 1 [ 1.600430] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.624899] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23970 usecs [ 1.625188] xen: registering gsi 18 triggering 0 polarity 1 [ 1.625206] Already setup the GSI :18 [ 1.649839] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 24147 usecs [ 1.650097] xen: registering gsi 19 triggering 0 polarity 1 [ 1.650179] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.650412] xen: registering gsi 18 triggering 0 polarity 1 [ 1.650416] Already setup the GSI :18 [ 1.674904] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 23974 usecs [ 1.675168] PCI: CLS 64 bytes, default 64 [ 1.675341] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.675461] software IO TLB: mapped [mem 0x000000001b200000-0x000000001f200000] (64MB) [ 1.675694] Unpacking initramfs... [ 1.675795] kvm_intel: VMX not supported by CPU 0 [ 1.676328] kvm_amd: SVM not supported by CPU 0 [ 1.676740] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cb378b39e7, max_idle_ns: 440795289550 ns [ 1.677246] clocksource: Switched to clocksource tsc [ 1.687562] Initialise system trusted keyrings [ 1.687978] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.688539] NFS: Registering the id_resolver key type [ 1.688659] Key type id_resolver registered [ 1.688776] Key type id_legacy registered [ 1.689049] 9p: Installing v9fs 9p2000 file system support [ 1.712943] Key type asymmetric registered [ 1.713110] Asymmetric key parser 'x509' registered [ 1.713295] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.713505] io scheduler mq-deadline registered [ 1.713609] io scheduler kyber registered [ 1.715572] xen: registering gsi 53 triggering 0 polarity 1 [ 1.715831] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.717742] xen: registering gsi 54 triggering 0 polarity 1 [ 1.717778] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.718165] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.718380] ACPI: button: Power Button [PWRB] [ 1.718529] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.718796] ACPI: button: Power Button [PWRF] [ 1.721885] ACPI: \_PR_.P001: Found 2 idle states [ 1.723655] ACPI: \_PR_.P002: Found 2 idle states [ 1.723830] ACPI: \_PR_.P003: Found 2 idle states [ 1.724003] ACPI: \_PR_.P004: Found 2 idle states [ 1.724166] ACPI: \_PR_.P005: Found 2 idle states [ 1.724368] ACPI: \_PR_.P006: Found 2 idle states [ 1.725496] xen:xen_evtchn: Event-channel device installed [ 1.725767] xen_pciback: backend is vpci [ 1.727094] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.727518] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.728429] hpet_acpi_add: no address or irqs in _CRS [ 1.728614] Non-volatile memory driver v1.3 [ 1.747142] loop: module loaded [ 1.762591] ahci 0000:00:11.0: version 3.0 [ 1.762810] xen: registering gsi 22 triggering 0 polarity 1 [ 1.762869] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.763101] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.763271] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.763388] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.765363] scsi host0: ahci [ 1.766170] scsi host1: ahci [ 1.767616] scsi host2: ahci [ 1.768090] scsi host3: ahci [ 1.768270] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.768419] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.768566] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.768719] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.769436] tun: Universal TUN/TAP device driver, 1.6 [ 1.769790] e100: Intel(R) PRO/100 Network Driver [ 1.769902] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.770023] sky2: driver version 1.30 [ 1.770218] xen_netfront: Initialising Xen virtual ethernet driver [ 1.770750] xen: registering gsi 16 triggering 0 polarity 1 [ 1.770773] Already setup the GSI :16 [ 1.770975] xen: registering gsi 17 triggering 0 polarity 1 [ 1.771004] Already setup the GSI :17 [ 1.771016] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.771405] xen: registering gsi 19 triggering 0 polarity 1 [ 1.771410] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 1.771440] Already setup the GSI :19 [ 1.771841] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.827922] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.828112] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.828262] usb usb1: Product: OHCI PCI host controller [ 1.828384] usb usb1: Manufacturer: Linux 6.10.0-rc2+ ohci_hcd [ 1.828495] usb usb1: SerialNumber: 0000:00:12.0 [ 1.829161] hub 1-0:1.0: USB hub found [ 1.829784] hub 1-0:1.0: 3 ports detected [ 1.832289] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.832611] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 1.832746] xen: registering gsi 16 triggering 0 polarity 1 [ 1.832778] Already setup the GSI :16 [ 1.832782] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.833056] ehci-pci 0000:00:12.2: debug port 1 [ 1.833299] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.839698] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.840141] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.840327] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.840476] usb usb2: Product: EHCI Host Controller [ 1.840593] usb usb2: Manufacturer: Linux 6.10.0-rc2+ ehci_hcd [ 1.840732] usb usb2: SerialNumber: 0000:00:12.2 [ 1.841260] hub 2-0:1.0: USB hub found [ 1.841400] hub 2-0:1.0: 6 ports detected [ 1.889147] Freeing initrd memory: 20192K [ 1.894042] hub 1-0:1.0: USB hub found [ 1.894258] hub 1-0:1.0: 3 ports detected [ 1.894831] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.895272] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 1.895422] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.895593] ehci-pci 0000:00:13.2: debug port 1 [ 1.895880] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.902727] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.903380] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.903540] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.903721] usb usb3: Product: EHCI Host Controller [ 1.903839] usb usb3: Manufacturer: Linux 6.10.0-rc2+ ehci_hcd [ 1.903963] usb usb3: SerialNumber: 0000:00:13.2 [ 1.904497] hub 3-0:1.0: USB hub found [ 1.904667] hub 3-0:1.0: 6 ports detected [ 1.905530] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.906434] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.907209] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.963593] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.964089] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.964406] usb usb4: Product: OHCI PCI host controller [ 1.964770] usb usb4: Manufacturer: Linux 6.10.0-rc2+ ohci_hcd [ 1.965094] usb usb4: SerialNumber: 0000:00:12.1 [ 1.966157] hub 4-0:1.0: USB hub found [ 1.966291] hub 4-0:1.0: 3 ports detected [ 1.966885] xen: registering gsi 18 triggering 0 polarity 1 [ 1.966904] Already setup the GSI :18 [ 1.967090] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.967462] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.967737] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 2.023989] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.024173] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.024314] usb usb5: Product: OHCI PCI host controller [ 2.024420] usb usb5: Manufacturer: Linux 6.10.0-rc2+ ohci_hcd [ 2.024529] usb usb5: SerialNumber: 0000:00:13.0 [ 2.025012] hub 5-0:1.0: USB hub found [ 2.025149] hub 5-0:1.0: 3 ports detected [ 2.025721] xen: registering gsi 18 triggering 0 polarity 1 [ 2.025734] Already setup the GSI :18 [ 2.025910] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 2.026173] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 2.026387] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 2.079341] ata4: SATA link down (SStatus 0 SControl 300) [ 2.079530] ata3: SATA link down (SStatus 0 SControl 300) [ 2.082357] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.082899] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.083235] usb usb6: Product: OHCI PCI host controller [ 2.083564] usb usb6: Manufacturer: Linux 6.10.0-rc2+ ohci_hcd [ 2.083968] usb usb6: SerialNumber: 0000:00:13.1 [ 2.085385] hub 6-0:1.0: USB hub found [ 2.085860] hub 6-0:1.0: 3 ports detected [ 2.088226] xen: registering gsi 18 triggering 0 polarity 1 [ 2.088265] Already setup the GSI :18 [ 2.088961] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 2.089806] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 2.090418] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 2.147496] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.147981] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.148307] usb usb7: Product: OHCI PCI host controller [ 2.148613] usb usb7: Manufacturer: Linux 6.10.0-rc2+ ohci_hcd [ 2.149002] usb usb7: SerialNumber: 0000:00:14.5 [ 2.150329] hub 7-0:1.0: USB hub found [ 2.150851] hub 7-0:1.0: 2 ports detected [ 2.152759] usbcore: registered new interface driver usblp [ 2.153212] usbcore: registered new interface driver usb-storage [ 2.153785] i8042: PNP: No PS/2 controller found. [ 2.154111] i8042: Probing ports directly. [ 2.158036] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.158181] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.158960] rtc_cmos 00:02: RTC can wake from S4 [ 2.159566] rtc_cmos 00:02: registered as rtc0 [ 2.159757] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 2.159931] device-mapper: uevent: version 1.0.3 [ 2.160123] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 2.160281] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 2.160452] hid: raw HID events driver (C) Jiri Kosina [ 2.160856] usbcore: registered new interface driver usbhid [ 2.160964] usbhid: USB HID core driver [ 2.161652] Initializing XFRM netlink socket [ 2.161800] NET: Registered PF_INET6 protocol family [ 2.162698] Segment Routing with IPv6 [ 2.162816] In-situ OAM (IOAM) with IPv6 [ 2.162961] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.163340] NET: Registered PF_PACKET protocol family [ 2.163526] 9pnet: Installing 9P2000 support [ 2.163673] Key type dns_resolver registered [ 2.163801] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 2.164775] IPI shorthand broadcast: enabled [ 2.169353] sched_clock: Marking stable (2142004391, 26661962)->(2184188046, -15521693) [ 2.170560] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.171097] registered taskstats version 1 [ 2.171201] Loading compiled-in X.509 certificates [ 2.175086] PM: Magic number: 12:762:560 [ 2.175367] printk: legacy console [netcon0] enabled [ 2.175515] netconsole: network logging started [ 2.175836] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.192162] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.192984] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.193178] ALSA device list: [ 2.193304] No soundcards found. [ 2.194232] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 2.232812] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.235181] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 2.235999] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA [ 2.238046] ata1.00: configured for UDMA/133 [ 2.238488] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 2.239834] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.240198] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.240757] sd 0:0:0:0: [sda] Write Protect is off [ 2.240787] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.240870] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.241344] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.242110] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 2.243938] ata2.00: ATAPI: ATAPI iHAS124 E, 4L07, max UDMA/100 [ 2.244873] ata2.00: configured for UDMA/100 [ 2.246642] scsi 1:0:0:0: CD-ROM ATAPI iHAS124 E 4L07 PQ: 0 ANSI: 5 [ 2.283455] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.283657] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.284067] sda: sda1 sda2 < sda5 > [ 2.285099] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.294851] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.295068] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.299390] Freeing unused kernel image (initmem) memory: 2680K [ 2.299590] Write protecting the kernel read-only data: 24576k [ 2.315154] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.392819] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.423673] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.423842] Run /init as init process [ 2.423944] with arguments: [ 2.423945] /init [ 2.423947] placeholder [ 2.423948] with environment: [ 2.423950] HOME=/ [ 2.423951] TERM=linux [ 2.555788] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.555986] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.556107] usb 6-2: Product: Hermon USB hidmouse Device [ 2.556222] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.562225] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.562521] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.566213] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.618067] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.730836] e1000e: Intel(R) PRO/1000 Network Driver [ 2.730963] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.731222] xen: registering gsi 48 triggering 0 polarity 1 [ 2.731264] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.731489] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.774495] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.818484] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f6 [ 2.818645] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.818858] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 2.819079] xen: registering gsi 47 triggering 0 polarity 1 [ 2.819106] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.819290] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.865760] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.912801] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f7 [ 2.912957] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.913145] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 2.914823] e1000e 0000:01:00.0 enx0cc47a0a48f6: renamed from eth0 [ 2.915118] e1000e 0000:02:00.0 enx0cc47a0a48f7: renamed from eth1 [ 3.067696] random: crng init done [ 3.731201] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.736464] EXT4-fs (dm-0): mounted filesystem d6946d58-2aca-47eb-b112-50860a6b93d8 ro with ordered data mode. Quota mode: none. [ 7.505833] EXT4-fs (dm-0): re-mounted d6946d58-2aca-47eb-b112-50860a6b93d8 r/w. Quota mode: none. [ 9.109086] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 9.152273] EXT4-fs (sda1): mounted filesystem d521699e-ca68-4f36-a4dd-3c1becc59d13 r/w with ordered data mode. Quota mode: none. [ 9.235155] Adding 1949692k swap on /dev/mapper/rimava1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 10.741855] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 10.742027] xenbr0: port 1(enx0cc47a0a48f6) entered disabled state [ 10.742141] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered allmulticast mode [ 10.742293] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered promiscuous mode [ 13.962730] e1000e 0000:01:00.0 enx0cc47a0a48f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 13.963276] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 13.963385] xenbr0: port 1(enx0cc47a0a48f6) entered forwarding state