[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc2+ (osstest@himrod0) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Fri Jun 7 19:24:18 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off, mlocked free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6080K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000014] Switching to timer-based delay loop, resolution 41ns [ 0.000522] Console: colour dummy device 80x30 [ 0.000541] printk: legacy console [hvc0] enabled [ 0.300753] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.311150] CPU: Testing write buffer coherency: ok [ 0.316092] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.325646] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.332059] pid_max: default: 32768 minimum: 301 [ 0.336846] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.344145] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.352529] /cpus/cpu@0 missing clock-frequency property [ 0.357329] /cpus/cpu@1 missing clock-frequency property [ 0.362723] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.369440] xen:grant_table: Grant tables using version 1 layout [ 0.374600] Grant table initialized [ 0.378130] xen:events: Using FIFO-based ABI [ 0.382431] Xen: initializing cpu0 [ 0.385955] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.393728] rcu: Hierarchical SRCU implementation. [ 0.397350] rcu: Max phase no-delay instances is 1000. [ 0.405590] EFI services will not be available. [ 0.408910] smp: Bringing up secondary CPUs ... [ 0.483032] Xen: initializing cpu1 [ 0.483190] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.483213] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.502183] smp: Brought up 1 node, 2 CPUs [ 0.505850] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.512137] CPU: All CPU(s) started in SVC mode. [ 0.518050] devtmpfs: initialized [ 0.530316] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.536867] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.546540] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.554423] pinctrl core: initialized pinctrl subsystem [ 0.561061] DMI not present or invalid. [ 0.564568] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.571180] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.580502] thermal_sys: Registered thermal governor 'step_wise' [ 0.580660] software IO TLB: area num 2. [ 0.589333] software IO TLB: only able to allocate 8 MB [ 0.596405] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.601607] No ATAGs? [ 0.603908] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.612605] Serial: AMBA PL011 UART driver [ 0.659228] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.687733] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.711018] xen:balloon: Initialising balloon driver [ 0.717454] iommu: Default domain type: Translated [ 0.720872] iommu: DMA domain TLB invalidation policy: strict mode [ 0.729600] SCSI subsystem initialized [ 0.732153] libata version 3.00 loaded. [ 0.732362] usbcore: registered new interface driver usbfs [ 0.737575] usbcore: registered new interface driver hub [ 0.742938] usbcore: registered new device driver usb [ 0.749606] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.753201] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.759445] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.764519] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.769445] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.775486] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.781282] pps_core: LinuxPPS API ver. 1 registered [ 0.785659] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.794882] PTP clock support registered [ 0.799100] EDAC MC: Ver: 3.0.0 [ 0.802443] scmi_core: SCMI protocol bus registered [ 0.808993] vgaarb: loaded [ 0.814910] clocksource: Switched to clocksource arch_sys_counter [ 0.829084] NET: Registered PF_INET protocol family [ 0.832730] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.840653] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.848324] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.856128] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.863954] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.871270] TCP: Hash tables configured (established 4096 bind 4096) [ 0.877612] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.884165] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.891313] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.903080] RPC: Registered named UNIX socket transport module. [ 0.907635] RPC: Registered udp transport module. [ 0.912395] RPC: Registered tcp transport module. [ 0.917184] RPC: Registered tcp-with-tls transport module. [ 0.922724] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.929249] PCI: CLS 0 bytes, default 64 [ 0.934655] Initialise system trusted keyrings [ 0.938005] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.944507] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.950402] Trying to unpack rootfs image as initramfs... [ 0.985588] NFS: Registering the id_resolver key type [ 0.989301] Key type id_resolver registered [ 0.993529] Key type id_legacy registered [ 0.997658] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.004386] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.016823] Key type asymmetric registered [ 1.019552] Asymmetric key parser 'x509' registered [ 1.024554] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.031996] io scheduler mq-deadline registered [ 1.036583] io scheduler kyber registered [ 1.040665] io scheduler bfq registered [ 1.181467] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.187724] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.217397] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.223635] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.257224] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.263432] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.301777] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.308021] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.320930] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.387665] xen:xen_evtchn: Event-channel device installed [ 1.487299] Freeing initrd memory: 11856K [ 1.523843] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.535157] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.543313] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.552234] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.561271] SuperH (H)SCI(F) driver initialized [ 1.565561] STMicroelectronics ASC driver initialized [ 1.570422] STM32 USART driver initialized [ 1.584951] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.593777] random: crng init done [ 1.612078] brd: module loaded [ 1.618052] loop: module loaded [ 1.641501] Invalid max_queues (4), will use default max: 2. [ 1.660103] tun: Universal TUN/TAP device driver, 1.6 [ 1.663967] CAN device driver interface [ 1.669120] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.680280] xen_netfront: Initialising Xen virtual ethernet driver [ 1.685151] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.690751] usbcore: registered new interface driver pegasus [ 1.696489] usbcore: registered new interface driver asix [ 1.701963] usbcore: registered new interface driver ax88179_178a [ 1.708121] usbcore: registered new interface driver cdc_ether [ 1.714010] usbcore: registered new interface driver smsc75xx [ 1.719835] usbcore: registered new interface driver smsc95xx [ 1.725661] usbcore: registered new interface driver net1080 [ 1.731374] usbcore: registered new interface driver cdc_subset [ 1.737369] usbcore: registered new interface driver zaurus [ 1.743004] usbcore: registered new interface driver cdc_ncm [ 1.752420] usbcore: registered new interface driver usb-storage [ 1.762939] i2c_dev: i2c /dev entries driver [ 1.781403] device-mapper: uevent: version 1.0.3 [ 1.784825] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.794443] cpu cpu0: OPP table can't be empty [ 1.799182] failed to register cpuidle driver [ 1.802543] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.810944] sdhci: Secure Digital Host Controller Interface driver [ 1.815917] sdhci: Copyright(c) Pierre Ossman [ 1.824064] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.831890] ledtrig-cpu: registered to indicate activity on CPUs [ 1.837359] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.843986] usbcore: registered new interface driver usbhid [ 1.848704] usbhid: USB HID core driver [ 1.859618] NET: Registered PF_INET6 protocol family [ 1.864130] Segment Routing with IPv6 [ 1.867021] In-situ OAM (IOAM) with IPv6 [ 1.870993] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.877437] NET: Registered PF_PACKET protocol family [ 1.882058] can: controller area network core [ 1.886538] NET: Registered PF_CAN protocol family [ 1.891356] can: raw protocol [ 1.894377] can: broadcast manager protocol [ 1.898663] can: netlink gateway - max_hops=1 [ 1.903367] Key type dns_resolver registered [ 1.908085] ThumbEE CPU extension supported. [ 1.911739] Registering SWP/SWPB emulation handler [ 1.926138] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.933005] Loading compiled-in X.509 certificates [ 1.976972] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.980569] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.987246] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.995379] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.036863] s5m-rtc s5m-rtc: registered as rtc0 [ 2.045727] s5m-rtc s5m-rtc: setting system clock to 2024-06-07T22:30:21 UTC (1717799421) [ 2.056756] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.061348] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.065796] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.072493] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.078434] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.084577] clk: Not disabling unused clocks [ 2.088149] PM: genpd: Disabling unused power domains [ 2.096791] Freeing unused kernel image (initmem) memory: 2048K [ 2.103080] Run /init as init process [ 2.105402] with arguments: [ 2.105409] /init [ 2.105415] with environment: [ 2.105420] HOME=/ [ 2.105425] TERM=linux [ 3.457916] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.472444] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.487863] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.574404] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.582353] Synopsys Designware Multimedia Card Interface Driver [ 3.591184] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.597418] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.604937] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.637614] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.637772] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.645615] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.650229] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.662695] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.676056] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.681676] exynos-ohci 12120000.usb: USB Host Controller [ 3.687225] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.695123] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.701984] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.710854] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.717694] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.736438] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.765440] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.770529] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.776104] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 125,32 bit host data width,128 deep fifo [ 3.785880] mmc_host mmc0: card is polling. [ 3.790345] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.796697] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.802679] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.811455] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.821411] exynos-ehci 12110000.usb: irq 126, io mem 0x12110000 [ 3.827769] exynos-ohci 12120000.usb: irq 126, io mem 0x12120000 [ 3.828349] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.843274] scsi host0: ahci-dwc [ 3.851126] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 3.861766] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.884793] hub 1-0:1.0: USB hub found [ 3.887669] hub 1-0:1.0: 3 ports detected [ 3.903907] hub 2-0:1.0: USB hub found [ 3.906765] hub 2-0:1.0: 3 ports detected [ 3.922170] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.926911] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.969376] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.978383] mmc0: new DDR MMC card at address 0001 [ 3.983393] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 3.989565] mmcblk0: p1 p2 p3 p4 [ 3.992606] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 3.997910] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.002616] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.047861] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.056358] mmc1: new high speed SDHC card at address aaaa [ 4.062556] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.364943] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.370756] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.376563] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.384282] ata1.00: configured for UDMA/133 [ 4.387837] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.397011] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.403191] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.408571] sd 0:0:0:0: [sda] Write Protect is off [ 4.413331] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.413403] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.422599] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.442580] sda: sda1 sda2 < sda5 > [ 4.445574] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.960738] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.969012] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.973157] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.992782] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 5.001263] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 5.007163] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.012450] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.020256] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.027803] hub 3-0:1.0: USB hub found [ 5.030631] hub 3-0:1.0: 1 port detected [ 5.035366] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.043436] hub 4-0:1.0: USB hub found [ 5.046670] hub 4-0:1.0: 1 port detected [ 5.203236] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.373820] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.482584] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.590739] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.698851] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.806996] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.915128] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.023224] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.131339] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.239439] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.648230] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.755983] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7.364334] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 10.819892] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.149497] EXT4-fs (dm-0): mounted filesystem 6223ae94-78a6-4df8-873a-f4e87c76b379 ro with ordered data mode. Quota mode: disabled. [ 14.998256] s5p-secss 10830000.sss: s5p-sss driver registered [ 15.040595] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.049884] mc: Linux media interface: v0.10 [ 15.220355] videodev: Linux video capture interface: v2.00 [ 15.487618] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.586236] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 15.640446] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 15.665440] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 15.669749] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.669855] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.683370] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 15.701299] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 15.731938] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.745920] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.753307] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.780840] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 15.786764] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 15.797201] blk_print_req_error: 6 callbacks suppressed [ 15.797216] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.829680] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 15.864990] usb3503 usb-hub: switched to HUB mode [ 15.868345] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.888984] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 15.909663] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 15.914498] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.028856] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.137003] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.225003] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.245239] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.353493] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.437551] hub 1-3:1.0: USB hub found [ 16.441235] hub 1-3:1.0: 3 ports detected [ 16.461656] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.517386] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.525139] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.533814] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.544984] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.553360] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.562099] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.570007] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.764946] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.917711] hub 1-3.2:1.0: USB hub found [ 16.920726] hub 1-3.2:1.0: 4 ports detected [ 16.959490] usbcore: registered new device driver onboard-usb-dev [ 16.982891] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.090645] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.099127] hub 1-3.2:1.0: USB hub found [ 17.102684] hub 1-3.2:1.0: 4 ports detected [ 17.115144] hub 1-3.2:1.0: USB hub found [ 17.118030] hub 1-3.2:1.0: 4 ports detected [ 17.434966] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.589173] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.699120] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 18.246902] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.261274] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.271179] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 7a:9e:9e:c9:e7:15 [ 18.975918] EXT4-fs (dm-0): re-mounted 6223ae94-78a6-4df8-873a-f4e87c76b379 r/w. Quota mode: disabled. [ 20.389268] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.437944] EXT4-fs (sda1): mounted filesystem bccf038b-390d-4635-a153-c46011f66db2 r/w with ordered data mode. Quota mode: disabled. [ 20.533362] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 23.012426] xenbr0: port 1(eth0) entered blocking state [ 23.016333] xenbr0: port 1(eth0) entered disabled state [ 23.021602] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 23.027480] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 23.038145] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 25.292276] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.298320] xenbr0: port 1(eth0) entered blocking state [ 25.303511] xenbr0: port 1(eth0) entered forwarding state [ 27.526769] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed