[ 0.000000] Linux version 6.10.0-rc3+ (osstest@himrod2) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Wed Jun 12 00:38:16 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000095fff] usable [ 0.000000] Xen: [mem 0x0000000000096000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020069fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SCM/H8SCM, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000011] Xen PV: Detected 6 vCPUS [ 0.037794] tsc: Fast TSC calibration using PIT [ 0.037795] tsc: Detected 3100.806 MHz processor [ 0.037797] tsc: Detected 3101.116 MHz TSC [ 0.038002] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.038006] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.038012] last_pfn = 0x2006a max_arch_pfn = 0x400000000 [ 0.038015] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.038017] MTRRs set to read-only [ 0.038019] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.062233] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.062245] ACPI: Early table checksum verification disabled [ 0.062965] ACPI: RSDP 0x00000000000FA1D0 000024 (v02 ACPIAM) [ 0.062972] ACPI: XSDT 0x00000000DFEA0100 000084 (v01 SMCI 20131125 MSFT 00000097) [ 0.062998] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.063029] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.063039] ACPI: DSDT 0x00000000DFEA0600 005699 (v01 1BA11 1BA11000 00000000 INTL 20051117) [ 0.063049] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.063057] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.063066] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.063076] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.063086] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.063095] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.063105] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.063114] ACPI: SRAT 0x00000000DFEAA6F0 000108 (v02 AMD AGESA 00000001 AMD 00000001) [ 0.063124] ACPI: SSDT 0x00000000DFEAA800 001158 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.063133] ACPI: EINJ 0x00000000DFEAB960 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.063142] ACPI: BERT 0x00000000DFEABAF0 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.063151] ACPI: ERST 0x00000000DFEABB20 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.063160] ACPI: HEST 0x00000000DFEABD30 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.063165] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.063167] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c98] [ 0.063169] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.063170] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.063171] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.063172] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.063174] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.063175] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.063176] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.063177] ACPI: Reserving SRAT table memory at [mem 0xdfeaa6f0-0xdfeaa7f7] [ 0.063178] ACPI: Reserving SSDT table memory at [mem 0xdfeaa800-0xdfeab957] [ 0.063179] ACPI: Reserving EINJ table memory at [mem 0xdfeab960-0xdfeaba8f] [ 0.063180] ACPI: Reserving BERT table memory at [mem 0xdfeabaf0-0xdfeabb1f] [ 0.063182] ACPI: Reserving ERST table memory at [mem 0xdfeabb20-0xdfeabd2f] [ 0.063183] ACPI: Reserving HEST table memory at [mem 0xdfeabd30-0xdfeabdd7] [ 0.063266] APIC: Switched APIC routing to: Xen PV [ 0.065510] Zone ranges: [ 0.065512] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.065514] DMA32 [mem 0x0000000001000000-0x0000000020069fff] [ 0.065516] Normal empty [ 0.065517] Movable zone start for each node [ 0.065518] Early memory node ranges [ 0.065519] node 0: [mem 0x0000000000001000-0x0000000000095fff] [ 0.065521] node 0: [mem 0x0000000000100000-0x0000000020069fff] [ 0.065523] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020069fff] [ 0.065531] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.065607] On node 0, zone DMA: 106 pages in unavailable ranges [ 0.068520] On node 0, zone DMA32: 32662 pages in unavailable ranges [ 0.068527] p2m virtual area at (____ptrval____), size is 40000000 [ 0.275247] Remapped 106 page(s) [ 0.275734] ACPI: PM-Timer IO Port: 0x808 [ 0.275760] CPU topo: CPU limit of 6 reached. Ignoring further CPUs [ 0.275781] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.275784] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.275803] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.275810] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.275819] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.275822] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.275839] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.275843] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.275853] CPU topo: Max. logical packages: 1 [ 0.275854] CPU topo: Max. logical dies: 1 [ 0.275855] CPU topo: Max. dies per package: 1 [ 0.275861] CPU topo: Max. threads per core: 1 [ 0.275862] CPU topo: Num. cores per package: 6 [ 0.275863] CPU topo: Num. threads per package: 6 [ 0.275864] CPU topo: Allowing 6 present CPUs plus 0 hotplug CPUs [ 0.275865] CPU topo: Rejected CPUs 2 [ 0.275879] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.275881] PM: hibernation: Registered nosave memory: [mem 0x00096000-0x000fffff] [ 0.275884] [mem 0x2006a000-0xdfe9dfff] available for PCI devices [ 0.275888] Booting kernel on Xen [ 0.275888] Xen version: 4.19-unstable (preserve-AD) [ 0.275892] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.281875] setup_percpu: NR_CPUS:64 nr_cpumask_bits:6 nr_cpu_ids:6 nr_node_ids:1 [ 0.282630] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u262144 [ 0.282637] pcpu-alloc: s194408 r8192 d30872 u262144 alloc=1*2097152 [ 0.282640] pcpu-alloc: [0] 0 1 2 3 4 5 - - [ 0.282699] xen: PV spinlocks enabled [ 0.282703] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.282706] Kernel command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.282765] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.282824] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.282895] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.283103] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.283106] mem auto-init: stack:all(zero), heap alloc:off, heap free:off, mlocked free:off [ 0.283109] software IO TLB: area num 8. [ 0.373003] Memory: 385988K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 138044K reserved, 0K cma-reserved) [ 0.373113] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.375521] Dynamic Preempt: voluntary [ 0.375640] rcu: Preemptible hierarchical RCU implementation. [ 0.375642] rcu: RCU event tracing is enabled. [ 0.375642] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.375644] Trampoline variant of Tasks RCU enabled. [ 0.375645] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.375646] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 [ 0.375666] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.382023] NR_IRQS: 4352, nr_irqs: 1016, preallocated irqs: 16 [ 0.382148] xen:events: Using FIFO-based ABI [ 0.382174] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.382180] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.382185] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.382190] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.382195] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.382200] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.382205] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.382209] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.382214] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.382219] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.382224] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.382229] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.382233] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.382238] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.382243] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.382252] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.388146] Console: colour VGA+ 80x25 [ 0.388150] printk: legacy console [tty0] enabled [ 0.401340] printk: legacy console [hvc0] enabled [ 0.401982] ACPI: Core revision 20240322 [ 0.404650] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.404802] Xen: using vcpuop timer interface [ 0.404806] installing Xen timer for CPU 0 [ 0.405031] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cb365ad133, max_idle_ns: 440795264807 ns [ 0.405184] Calibrating delay loop (skipped), value calculated using timer frequency.. 6202.23 BogoMIPS (lpj=3101116) [ 0.405366] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.405594] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.405700] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.405810] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.406191] Spectre V2 : Mitigation: Retpolines [ 0.406291] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.406431] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.406537] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.406643] RETBleed: Mitigation: untrained return thunk [ 0.406745] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.406887] Speculative Store Bypass: Vulnerable [ 0.407002] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.407179] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.407187] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.407295] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.407401] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.428406] Freeing SMP alternatives memory: 40K [ 0.428525] pid_max: default: 32768 minimum: 301 [ 0.428651] LSM: initializing lsm=capability,selinux [ 0.428760] SELinux: Initializing. [ 0.428888] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.429028] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.430307] cpu 0 spinlock event irq 57 [ 0.430417] VPMU disabled by hypervisor. [ 0.430892] Performance Events: PMU not available due to virtualization, using software events only. [ 0.431189] signal: max sigframe size: 1776 [ 0.431341] rcu: Hierarchical SRCU implementation. [ 0.431442] rcu: Max phase no-delay instances is 400. [ 0.436847] smp: Bringing up secondary CPUs ... [ 0.437137] installing Xen timer for CPU 1 [ 0.437505] installing Xen timer for CPU 2 [ 0.437873] installing Xen timer for CPU 3 [ 0.438234] installing Xen timer for CPU 4 [ 0.438625] installing Xen timer for CPU 5 [ 0.023926] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.438820] cpu 1 spinlock event irq 87 [ 0.023926] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.439255] cpu 2 spinlock event irq 88 [ 0.023926] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.439546] cpu 3 spinlock event irq 89 [ 0.023926] [Firmware Bug]: CPU 4: APIC ID mismatch. CPUID: 0x0004 APIC: 0x0014 [ 0.440255] cpu 4 spinlock event irq 90 [ 0.023926] [Firmware Bug]: CPU 5: APIC ID mismatch. CPUID: 0x0005 APIC: 0x0015 [ 0.440506] cpu 5 spinlock event irq 91 [ 0.441253] smp: Brought up 1 node, 6 CPUs [ 0.441527] devtmpfs: initialized [ 0.441527] x86/mm: Memory block size: 128MB [ 0.442403] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.442442] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.442593] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.442822] PM: RTC time: 01:13:05, date: 2024-06-12 [ 0.443348] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.443479] xen:grant_table: Grant tables using version 1 layout [ 0.443622] Grant table initialized [ 0.444016] audit: initializing netlink subsys (disabled) [ 0.444195] audit: type=2000 audit(1718154785.890:1): state=initialized audit_enabled=0 res=1 [ 0.444290] thermal_sys: Registered thermal governor 'step_wise' [ 0.444290] thermal_sys: Registered thermal governor 'user_space' [ 0.444433] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.445188] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.520060] PCI: Using configuration type 1 for base access [ 0.520236] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.520399] ACPI: Added _OSI(Module Device) [ 0.520399] ACPI: Added _OSI(Processor Device) [ 0.520436] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.521191] ACPI: Added _OSI(Processor Aggregator Device) [ 0.526245] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.526787] xen: registering gsi 9 triggering 0 polarity 1 [ 0.530279] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.530639] ACPI: Interpreter enabled [ 0.530754] ACPI: PM: (supports S0 S1 S4 S5) [ 0.530857] ACPI: Using IOAPIC for interrupt routing [ 0.531005] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.531150] PCI: Using E820 reservations for host bridge windows [ 0.531345] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.540885] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.541007] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.541156] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.541187] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.541331] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.541731] PCI host bridge to bus 0000:00 [ 0.541831] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.541946] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.542054] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.542186] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.542325] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.542462] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.542619] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.543130] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.543527] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.543733] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.543894] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.544006] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.544161] pci 0000:00:09.0: enabling Extended Tags [ 0.544299] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.544571] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.544786] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.544900] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.545011] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.545205] pci 0000:00:0a.0: enabling Extended Tags [ 0.545419] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.545718] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601 conventional PCI endpoint [ 0.545902] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.546027] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.546151] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.546209] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.546333] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.546465] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.546816] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.546999] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.547369] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.547553] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.547954] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.548137] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.548401] pci 0000:00:12.2: supports D1 D2 [ 0.548500] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.548763] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.548945] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.549322] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.549504] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.549902] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.550084] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.550402] pci 0000:00:13.2: supports D1 D2 [ 0.550509] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.550789] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.551280] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.551462] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.551586] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.551713] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.551849] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.551974] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.552129] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.552186] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.552292] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.552399] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.552691] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.553169] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.553270] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.553395] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.553519] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.553788] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.553971] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.554360] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.554779] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.555079] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.555347] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.555695] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.556085] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.556501] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.556689] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.556847] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.556980] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.557344] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.560228] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.560518] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.560706] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.560864] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.560999] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.561366] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.564226] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.564386] pci_bus 0000:03: extended config space not accessible [ 0.564555] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.564743] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.565211] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.565342] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.565610] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.565987] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.566115] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.566187] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.566333] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.566478] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.566622] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.566836] pci_bus 0000:00: on NUMA node 0 [ 0.567283] xen: registering gsi 13 triggering 1 polarity 0 [ 0.567688] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.567859] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.568029] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.568213] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.568382] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.568550] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.568718] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.568885] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.569089] xen:balloon: Initialising balloon driver [ 0.569267] iommu: Default domain type: Translated [ 0.569371] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.569563] SCSI subsystem initialized [ 0.569671] libata version 3.00 loaded. [ 0.569671] ACPI: bus type USB registered [ 0.569671] usbcore: registered new interface driver usbfs [ 0.569671] usbcore: registered new interface driver hub [ 0.570190] usbcore: registered new device driver usb [ 0.570312] pps_core: LinuxPPS API ver. 1 registered [ 0.570415] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.570563] PTP clock support registered [ 0.570681] Advanced Linux Sound Architecture Driver Initialized. [ 0.571225] NetLabel: Initializing [ 0.571324] NetLabel: domain hash size = 128 [ 0.571422] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.571543] NetLabel: unlabeled traffic allowed by default [ 0.571669] PCI: Using ACPI for IRQ routing [ 0.596460] PCI: pci_cache_line_size set to 64 bytes [ 0.596614] e820: reserve RAM buffer [mem 0x00096000-0x0009ffff] [ 0.596617] e820: reserve RAM buffer [mem 0x2006a000-0x23ffffff] [ 0.596640] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.596640] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.596640] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.596640] vgaarb: loaded [ 0.597405] clocksource: Switched to clocksource tsc-early [ 0.597610] VFS: Disk quotas dquot_6.6.0 [ 0.597724] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.597868] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.598017] pnp: PnP ACPI init [ 0.598189] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.598415] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.598804] xen: registering gsi 8 triggering 1 polarity 0 [ 0.598981] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.599291] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.599405] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.599822] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.599929] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.600035] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.600140] system 00:05: [io 0x040b] has been reserved [ 0.600258] system 00:05: [io 0x04d6] has been reserved [ 0.600361] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.600466] system 00:05: [io 0x0c14] has been reserved [ 0.600569] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.600675] system 00:05: [io 0x0c52] has been reserved [ 0.600783] system 00:05: [io 0x0c6c] has been reserved [ 0.600908] system 00:05: [io 0x0c6f] has been reserved [ 0.601011] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.601117] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.601239] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.601345] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.601451] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.601557] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.601661] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.601767] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.601872] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.601977] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.602082] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.602205] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.602314] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.602423] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.602757] xen: registering gsi 4 triggering 1 polarity 0 [ 0.602760] Already setup the GSI :4 [ 0.602857] pnp 00:06: [dma 0 disabled] [ 0.603125] xen: registering gsi 3 triggering 1 polarity 0 [ 0.603131] pnp 00:07: [dma 0 disabled] [ 0.603287] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.603613] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.603791] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.603902] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.604011] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.604121] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.604387] pnp: PnP ACPI: found 10 devices [ 0.622967] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.623100] NET: Registered PF_INET protocol family [ 0.623267] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.623644] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.623789] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.623930] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.624076] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.624251] TCP: Hash tables configured (established 4096 bind 4096) [ 0.624401] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.624534] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.624684] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.624966] RPC: Registered named UNIX socket transport module. [ 0.625073] RPC: Registered udp transport module. [ 0.625172] RPC: Registered tcp transport module. [ 0.625287] RPC: Registered tcp-with-tls transport module. [ 0.625390] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.625850] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.625958] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.626073] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.626214] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.626319] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.626432] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.626557] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.626667] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.626781] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.626931] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.627037] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.627177] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.627309] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.627418] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.627527] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.627630] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.627737] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.627840] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.627947] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.628052] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.628159] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.628278] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.628386] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.628498] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.628618] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.628852] xen: registering gsi 16 triggering 0 polarity 1 [ 0.628873] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.278347] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 634330 usecs [ 1.278568] xen: registering gsi 16 triggering 0 polarity 1 [ 1.278577] Already setup the GSI :16 [ 1.302349] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 23275 usecs [ 1.302573] xen: registering gsi 17 triggering 0 polarity 1 [ 1.302617] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.302775] xen: registering gsi 18 triggering 0 polarity 1 [ 1.302791] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.326349] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23071 usecs [ 1.326568] xen: registering gsi 18 triggering 0 polarity 1 [ 1.326576] Already setup the GSI :18 [ 1.350347] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 23272 usecs [ 1.350571] xen: registering gsi 19 triggering 0 polarity 1 [ 1.350608] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.350785] xen: registering gsi 18 triggering 0 polarity 1 [ 1.350789] Already setup the GSI :18 [ 1.374338] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 23049 usecs [ 1.374543] PCI: CLS 64 bytes, default 64 [ 1.374678] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.374797] software IO TLB: mapped [mem 0x000000001b200000-0x000000001f200000] (64MB) [ 1.374971] Unpacking initramfs... [ 1.374999] kvm_intel: VMX not supported by CPU 0 [ 1.375182] kvm_amd: SVM not supported by CPU 0 [ 1.375320] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cb365ad133, max_idle_ns: 440795264807 ns [ 1.378836] clocksource: Switched to clocksource tsc [ 1.438008] Initialise system trusted keyrings [ 1.438271] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.438606] NFS: Registering the id_resolver key type [ 1.438724] Key type id_resolver registered [ 1.438829] Key type id_legacy registered [ 1.439045] 9p: Installing v9fs 9p2000 file system support [ 1.462350] Key type asymmetric registered [ 1.462480] Asymmetric key parser 'x509' registered [ 1.462629] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.462791] io scheduler mq-deadline registered [ 1.462899] io scheduler kyber registered [ 1.463903] xen: registering gsi 53 triggering 0 polarity 1 [ 1.463970] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.464290] xen: registering gsi 54 triggering 0 polarity 1 [ 1.464309] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.464665] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.464863] ACPI: button: Power Button [PWRB] [ 1.465025] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.465246] ACPI: button: Power Button [PWRF] [ 1.467666] ACPI: \_PR_.P001: Found 2 idle states [ 1.469325] ACPI: \_PR_.P002: Found 2 idle states [ 1.469490] ACPI: \_PR_.P003: Found 2 idle states [ 1.469672] ACPI: \_PR_.P004: Found 2 idle states [ 1.469840] ACPI: \_PR_.P005: Found 2 idle states [ 1.470035] ACPI: \_PR_.P006: Found 2 idle states [ 1.470670] xen:xen_evtchn: Event-channel device installed [ 1.470886] xen_pciback: backend is vpci [ 1.471700] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.472157] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.472973] hpet_acpi_add: no address or irqs in _CRS [ 1.473160] Non-volatile memory driver v1.3 [ 1.476105] loop: module loaded [ 1.483337] ahci 0000:00:11.0: version 3.0 [ 1.483449] xen: registering gsi 22 triggering 0 polarity 1 [ 1.483491] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.483642] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.483789] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.483897] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.485204] scsi host0: ahci [ 1.485575] scsi host1: ahci [ 1.485895] scsi host2: ahci [ 1.486231] scsi host3: ahci [ 1.486381] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.486524] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.486666] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.486817] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.487400] tun: Universal TUN/TAP device driver, 1.6 [ 1.487607] e100: Intel(R) PRO/100 Network Driver [ 1.487709] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.487831] sky2: driver version 1.30 [ 1.487997] xen_netfront: Initialising Xen virtual ethernet driver [ 1.488330] xen: registering gsi 16 triggering 0 polarity 1 [ 1.488336] Already setup the GSI :16 [ 1.488490] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.488496] xen: registering gsi 17 triggering 0 polarity 1 [ 1.488557] xen: registering gsi 19 triggering 0 polarity 1 [ 1.488566] Already setup the GSI :19 [ 1.488666] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 1.488711] Already setup the GSI :17 [ 1.488900] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.540424] Freeing initrd memory: 20192K [ 1.545141] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.545290] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.545427] usb usb1: Product: OHCI PCI host controller [ 1.545530] usb usb1: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.545636] usb usb1: SerialNumber: 0000:00:12.0 [ 1.545965] hub 1-0:1.0: USB hub found [ 1.546094] hub 1-0:1.0: 3 ports detected [ 1.546389] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.546486] xen: registering gsi 16 triggering 0 polarity 1 [ 1.546518] Already setup the GSI :16 [ 1.546632] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2 [ 1.546778] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.546960] ehci-pci 0000:00:13.2: debug port 1 [ 1.547156] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.554013] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.554293] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.554437] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.554574] usb usb2: Product: EHCI Host Controller [ 1.554675] usb usb2: Manufacturer: Linux 6.10.0-rc3+ ehci_hcd [ 1.554793] usb usb2: SerialNumber: 0000:00:13.2 [ 1.555093] hub 2-0:1.0: USB hub found [ 1.555218] hub 2-0:1.0: 6 ports detected [ 1.614142] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.614361] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 3 [ 1.614504] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.614666] ehci-pci 0000:00:12.2: debug port 1 [ 1.614854] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.621979] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.622145] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.622287] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.622423] usb usb3: Product: EHCI Host Controller [ 1.622527] usb usb3: Manufacturer: Linux 6.10.0-rc3+ ehci_hcd [ 1.622646] usb usb3: SerialNumber: 0000:00:12.2 [ 1.622894] hub 3-0:1.0: USB hub found [ 1.623018] hub 3-0:1.0: 6 ports detected [ 1.675024] hub 1-0:1.0: USB hub found [ 1.675180] hub 1-0:1.0: 3 ports detected [ 1.675400] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.675616] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.675796] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.731069] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.731217] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.731354] usb usb4: Product: OHCI PCI host controller [ 1.731456] usb usb4: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.731560] usb usb4: SerialNumber: 0000:00:12.1 [ 1.731837] hub 4-0:1.0: USB hub found [ 1.731973] hub 4-0:1.0: 3 ports detected [ 1.732290] xen: registering gsi 18 triggering 0 polarity 1 [ 1.732295] Already setup the GSI :18 [ 1.732426] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.732628] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.732822] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 1.789037] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.789185] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.789322] usb usb5: Product: OHCI PCI host controller [ 1.789424] usb usb5: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.789527] usb usb5: SerialNumber: 0000:00:13.0 [ 1.789840] hub 5-0:1.0: USB hub found [ 1.789997] hub 5-0:1.0: 3 ports detected [ 1.790337] xen: registering gsi 18 triggering 0 polarity 1 [ 1.790342] Already setup the GSI :18 [ 1.790473] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 1.790651] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 1.790825] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 1.794848] ata3: SATA link down (SStatus 0 SControl 300) [ 1.795003] ata4: SATA link down (SStatus 0 SControl 300) [ 1.847069] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.847216] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.847353] usb usb6: Product: OHCI PCI host controller [ 1.847456] usb usb6: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.847560] usb usb6: SerialNumber: 0000:00:13.1 [ 1.847821] hub 6-0:1.0: USB hub found [ 1.847950] hub 6-0:1.0: 3 ports detected [ 1.848306] xen: registering gsi 18 triggering 0 polarity 1 [ 1.848311] Already setup the GSI :18 [ 1.848440] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 1.848617] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 1.848790] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 1.904068] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.904215] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.904352] usb usb7: Product: OHCI PCI host controller [ 1.904454] usb usb7: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.904557] usb usb7: SerialNumber: 0000:00:14.5 [ 1.904842] hub 7-0:1.0: USB hub found [ 1.905013] hub 7-0:1.0: 2 ports detected [ 1.905378] usbcore: registered new interface driver usblp [ 1.905506] usbcore: registered new interface driver usb-storage [ 1.905648] i8042: PNP: No PS/2 controller found. [ 1.905749] i8042: Probing ports directly. [ 1.908639] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.908745] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.909162] rtc_cmos 00:02: RTC can wake from S4 [ 1.909665] rtc_cmos 00:02: registered as rtc0 [ 1.909807] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 1.909986] device-mapper: uevent: version 1.0.3 [ 1.910164] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.910322] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 1.910476] hid: raw HID events driver (C) Jiri Kosina [ 1.910778] usbcore: registered new interface driver usbhid [ 1.910882] usbhid: USB HID core driver [ 1.911379] Initializing XFRM netlink socket [ 1.911512] NET: Registered PF_INET6 protocol family [ 1.912017] Segment Routing with IPv6 [ 1.912126] In-situ OAM (IOAM) with IPv6 [ 1.912257] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.912507] NET: Registered PF_PACKET protocol family [ 1.912633] 9pnet: Installing 9P2000 support [ 1.912749] Key type dns_resolver registered [ 1.912861] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 1.913475] IPI shorthand broadcast: enabled [ 1.917859] sched_clock: Marking stable (1894004986, 22926881)->(1922776459, -5844592) [ 1.918312] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.918648] registered taskstats version 1 [ 1.918748] Loading compiled-in X.509 certificates [ 1.922406] PM: Magic number: 12:172:205 [ 1.922566] printk: legacy console [netcon0] enabled [ 1.922708] netconsole: network logging started [ 1.922919] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 1.932590] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 1.932984] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 1.933769] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 1.933957] ALSA device list: [ 1.934054] No soundcards found. [ 1.948992] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.949135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.950458] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 1.950890] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA [ 1.952442] ata1.00: configured for UDMA/133 [ 1.952720] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 1.953545] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.953584] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.953821] sd 0:0:0:0: [sda] Write Protect is off [ 1.953925] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.953959] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.954140] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 1.954551] ata2.00: ATAPI: ATAPI iHAS124 E, 4L07, max UDMA/100 [ 1.955427] ata2.00: configured for UDMA/100 [ 1.956956] scsi 1:0:0:0: CD-ROM ATAPI iHAS124 E 4L07 PQ: 0 ANSI: 5 [ 1.980046] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.980202] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.986324] sda: sda1 sda2 < sda5 > [ 1.986729] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.986789] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.986954] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.988598] Freeing unused kernel image (initmem) memory: 2680K [ 1.988731] Write protecting the kernel read-only data: 24576k [ 2.000138] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.092959] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.107649] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.107764] Run /init as init process [ 2.107860] with arguments: [ 2.107862] /init [ 2.107863] placeholder [ 2.107864] with environment: [ 2.107866] HOME=/ [ 2.107867] TERM=linux [ 2.257997] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.258158] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.258269] usb 6-2: Product: Hermon USB hidmouse Device [ 2.258372] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.264495] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.264840] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.268557] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.320394] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.357109] e1000e: Intel(R) PRO/1000 Network Driver [ 2.357236] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.357466] xen: registering gsi 48 triggering 0 polarity 1 [ 2.357532] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.357761] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.400794] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.444874] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f6 [ 2.445041] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.445231] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 2.445507] xen: registering gsi 47 triggering 0 polarity 1 [ 2.445538] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.445717] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.493081] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.540033] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f7 [ 2.540190] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.540378] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 2.542176] e1000e 0000:01:00.0 enx0cc47a0a48f6: renamed from eth0 [ 2.542503] e1000e 0000:02:00.0 enx0cc47a0a48f7: renamed from eth1 [ 2.646960] random: crng init done [ 3.273836] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.279196] EXT4-fs (dm-0): mounted filesystem 24dda781-3e93-4f7e-9e63-32379b951c52 ro with ordered data mode. Quota mode: none. [ 6.857105] EXT4-fs (dm-0): re-mounted 24dda781-3e93-4f7e-9e63-32379b951c52 r/w. Quota mode: none. [ 7.740375] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 7.756240] EXT4-fs (sda1): mounted filesystem d02bf9b3-e9b8-4070-98b6-4333116216ff r/w with ordered data mode. Quota mode: none. [ 7.823617] Adding 1949692k swap on /dev/mapper/rimava1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 9.375345] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 9.375526] xenbr0: port 1(enx0cc47a0a48f6) entered disabled state [ 9.375639] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered allmulticast mode [ 9.375792] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered promiscuous mode [ 12.482000] e1000e 0000:01:00.0 enx0cc47a0a48f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 12.482512] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 12.482621] xenbr0: port 1(enx0cc47a0a48f6) entered forwarding state