[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-21-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.90-1 (2024-05-03) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015524K/2097152K available (12288K kernel code, 1714K rwdata, 3748K rodata, 2048K init, 382K bss, 65244K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39974 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002620] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002635] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002650] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002661] Ignoring duplicate/late registration of read_current_timer delay [ 0.003026] Console: colour dummy device 80x30 [ 0.003067] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003081] CPU: Testing write buffer coherency: ok [ 0.003123] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003131] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003138] pid_max: default: 32768 minimum: 301 [ 0.003497] LSM: Security Framework initializing [ 0.003570] landlock: Up and running. [ 0.003574] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003758] AppArmor: AppArmor initialized [ 0.003771] TOMOYO Linux initialized [ 0.003816] LSM support for eBPF active [ 0.004059] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004074] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005488] /cpus/cpu@0 missing clock-frequency property [ 0.005516] /cpus/cpu@1 missing clock-frequency property [ 0.005530] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006488] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006495] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006600] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006606] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006749] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007909] rcu: Hierarchical SRCU implementation. [ 0.007915] rcu: Max phase no-delay instances is 1000. [ 0.010045] EFI services will not be available. [ 0.010390] smp: Bringing up secondary CPUs ... [ 0.011135] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011148] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011278] smp: Brought up 1 node, 2 CPUs [ 0.011287] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011295] CPU: All CPU(s) started in HYP mode. [ 0.011299] CPU: Virtualization extensions available. [ 0.012170] devtmpfs: initialized [ 0.023681] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023923] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023948] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024504] pinctrl core: initialized pinctrl subsystem [ 0.025254] DMI not present or invalid. [ 0.025929] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027493] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.029077] audit: initializing netlink subsys (disabled) [ 0.029282] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030491] thermal_sys: Registered thermal governor 'fair_share' [ 0.030499] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030503] thermal_sys: Registered thermal governor 'step_wise' [ 0.030508] thermal_sys: Registered thermal governor 'user_space' [ 0.030513] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030714] No ATAGs? [ 0.030781] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030790] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031885] Serial: AMBA PL011 UART driver [ 0.085344] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.092608] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.095847] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.095856] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.102770] iommu: Default domain type: Translated [ 0.102778] iommu: DMA domain TLB invalidation policy: strict mode [ 0.103759] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.104293] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.104304] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.104952] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.104982] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.105188] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.105550] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.105561] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.105958] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.106253] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.106263] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.106567] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.106685] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.106695] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.106881] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.107098] pps_core: LinuxPPS API ver. 1 registered [ 0.107103] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.107138] PTP clock support registered [ 0.108642] NetLabel: Initializing [ 0.108648] NetLabel: domain hash size = 128 [ 0.108654] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.108707] NetLabel: unlabeled traffic allowed by default [ 0.108885] vgaarb: loaded [ 0.109451] clocksource: Switched to clocksource mct-frc [ 0.110030] VFS: Disk quotas dquot_6.6.0 [ 0.110115] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.110867] AppArmor: AppArmor Filesystem Enabled [ 0.121097] NET: Registered PF_INET protocol family [ 0.121288] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.122782] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.122883] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.122908] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.123008] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.123239] TCP: Hash tables configured (established 8192 bind 8192) [ 0.123477] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.123578] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123620] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123840] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.123877] NET: Registered PF_XDP protocol family [ 0.123887] PCI: CLS 0 bytes, default 64 [ 0.124401] Trying to unpack rootfs image as initramfs... [ 0.124754] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.130180] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.195560] Initialise system trusted keyrings [ 0.195637] Key type blacklist registered [ 0.196848] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.205198] zbud: loaded [ 0.208815] integrity: Platform Keyring initialized [ 0.208847] integrity: Machine keyring initialized [ 0.208857] Key type asymmetric registered [ 0.208864] Asymmetric key parser 'x509' registered [ 1.431141] Freeing initrd memory: 25116K [ 1.453413] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.453728] bounce: pool size: 64 pages [ 1.453912] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.454093] io scheduler mq-deadline registered [ 1.459247] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.480361] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.480373] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.482826] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.482835] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.483656] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.483665] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.484511] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.484520] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.486916] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.489738] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.492506] Serial: AMBA driver [ 1.492732] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.493214] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.493759] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.574574] printk: console [ttySAC2] enabled [ 2.579395] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.590100] STM32 USART driver initialized [ 2.604493] mousedev: PS/2 mouse device common for all mice [ 2.635759] s5m-rtc s5m-rtc: registered as rtc0 [ 2.644390] s5m-rtc s5m-rtc: setting system clock to 2024-06-14T14:33:26 UTC (1718375606) [ 2.654297] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.661809] ledtrig-cpu: registered to indicate activity on CPUs [ 2.669836] NET: Registered PF_INET6 protocol family [ 2.693933] Segment Routing with IPv6 [ 2.696174] In-situ OAM (IOAM) with IPv6 [ 2.700163] mip6: Mobile IPv6 [ 2.703018] NET: Registered PF_PACKET protocol family [ 2.708180] mpls_gso: MPLS GSO support [ 2.712212] ThumbEE CPU extension supported. [ 2.716026] Registering SWP/SWPB emulation handler [ 2.721285] registered taskstats version 1 [ 2.724902] Loading compiled-in X.509 certificates [ 3.181513] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.188831] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.199901] zswap: loaded using pool lzo/zbud [ 3.203895] Key type .fscrypt registered [ 3.207163] Key type fscrypt-provisioning registered [ 3.231504] Key type encrypted registered [ 3.234104] AppArmor: AppArmor sha1 policy hashing enabled [ 3.239571] ima: No TPM chip found, activating TPM-bypass! [ 3.245032] ima: Allocated hash algorithm: sha256 [ 3.249750] ima: No architecture policies found [ 3.254258] evm: Initialising EVM extended attributes: [ 3.259330] evm: security.selinux [ 3.262623] evm: security.SMACK64 (disabled) [ 3.266870] evm: security.SMACK64EXEC (disabled) [ 3.271469] evm: security.SMACK64TRANSMUTE (disabled) [ 3.276504] evm: security.SMACK64MMAP (disabled) [ 3.281104] evm: security.apparmor [ 3.284489] evm: security.ima [ 3.287440] evm: security.capability [ 3.291005] evm: HMAC attrs: 0x1 [ 3.872073] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.878075] clk: Disabling unused clocks [ 3.890953] Freeing unused kernel image (initmem) memory: 2048K [ 3.895832] Checked W+X mappings: passed, no W+X pages found [ 3.901075] Run /init as init process [ 3.904707] with arguments: [ 3.904715] /init [ 3.904721] with environment: [ 3.904726] HOME=/ [ 3.904732] TERM=linux [ 4.829267] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.855372] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.871726] usbcore: registered new interface driver usbfs [ 4.904963] Synopsys Designware Multimedia Card Interface Driver [ 4.906979] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.918380] usbcore: registered new interface driver hub [ 4.926604] usbcore: registered new device driver usb [ 4.939915] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.941492] SCSI subsystem initialized [ 4.946337] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.957371] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.962384] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 5.010662] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 5.015698] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.035210] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.043557] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.052366] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107,32 bit host data width,128 deep fifo [ 5.066353] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.090983] mmc_host mmc1: card is polling. [ 5.121509] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.149963] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 5.169588] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.172061] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.183429] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 5.203326] mmc0: new high speed SDHC card at address aaaa [ 5.215353] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 5.215423] libata version 3.00 loaded. [ 5.236346] mmcblk0: mmc0:aaaa SU04G 3.69 GiB [ 5.241869] exynos-ohci 12120000.usb: USB Host Controller [ 5.244085] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.257754] exynos-ehci 12110000.usb: irq 109, io mem 0x12110000 [ 5.266448] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.278319] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.278953] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.288152] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.291881] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.309430] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.315714] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.316347] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.323385] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.330562] usb usb1: Product: EHCI Host Controller [ 5.339410] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.344265] usb usb1: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 5.344273] usb usb1: SerialNumber: 12110000.usb [ 5.357099] mmc1: new DDR MMC card at address 0001 [ 5.369405] exynos-ohci 12120000.usb: irq 109, io mem 0x12120000 [ 5.390715] mmcblk1: mmc1:0001 M4G1FB 3.64 GiB [ 5.395480] scsi host0: ahci-dwc [ 5.396676] hub 1-0:1.0: USB hub found [ 5.397910] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.402010] hub 1-0:1.0: 3 ports detected [ 5.415836] mmcblk1: p1 p2 p3 p4 [ 5.420397] mmcblk1boot0: mmc1:0001 M4G1FB 1.00 MiB [ 5.441904] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.448761] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.455955] usb usb2: Product: USB Host Controller [ 5.460716] usb usb2: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 5.467209] usb usb2: SerialNumber: 12120000.usb [ 5.476289] mmcblk1boot1: mmc1:0001 M4G1FB 1.00 MiB [ 5.482936] mmcblk1rpmb: mmc1:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.489522] hub 2-0:1.0: USB hub found [ 5.491924] hub 2-0:1.0: 3 ports detected [ 5.783877] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.858045] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.893519] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.899087] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.904936] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.912383] ata1.00: configured for UDMA/133 [ 5.916366] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.984645] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.988806] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.991489] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.006142] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.018551] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.023542] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.028601] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.036306] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.042968] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.050999] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.058186] usb usb3: Product: xHCI Host Controller [ 6.063040] usb usb3: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.069553] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.075105] hub 3-0:1.0: USB hub found [ 6.078319] hub 3-0:1.0: 1 port detected [ 6.082694] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.090309] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.098395] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.105608] usb usb4: Product: xHCI Host Controller [ 6.105817] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.110432] usb usb4: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.126327] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.132056] hub 4-0:1.0: USB hub found [ 6.134986] hub 4-0:1.0: 1 port detected [ 6.138414] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.146328] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.154969] sd 0:0:0:0: [sda] Write Protect is off [ 6.158325] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.158431] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.168177] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.191345] sda: sda1 sda2 < sda5 > [ 6.194218] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.219913] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.328057] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.817263] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 6.891460] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 6.999928] I/O error, dev mmcblk0, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 7.107961] I/O error, dev mmcblk0, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 7.205474] random: crng init done [ 7.216005] I/O error, dev mmcblk0, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 7.318739] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.324176] I/O error, dev mmcblk0, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 7.329715] device-mapper: uevent: version 1.0.3 [ 7.343712] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.438930] I/O error, dev mmcblk0, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 7.546979] I/O error, dev mmcblk0, sector 7744005 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 10.948069] Buffer I/O error on dev mmcblk0, logical block 968000, async page read [ 14.112251] PM: Image not found (code -22) [ 14.647125] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 14.888496] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 15.206931] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 18.603681] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 18.636646] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 18.751371] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 18.823079] panfrost 11800000.gpu: clock rate = 533000000 [ 18.920951] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 18.927263] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 18.935405] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 18.947146] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 18.981500] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 18.997020] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 19.050881] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 19.057515] usb3503 usb-hub: switched to HUB mode [ 19.063887] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 19.184424] blk_print_req_error: 30 callbacks suppressed [ 19.184435] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 19.298052] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 19.385546] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 19.406673] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 19.515005] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 19.551964] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 19.558892] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 19.588015] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 19.601114] hub 1-3:1.0: USB hub found [ 19.603883] hub 1-3:1.0: 3 ports detected [ 19.604039] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 19.676497] OF: graph: no port node found in /soc/hdmi@14530000 [ 19.689423] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 19.695762] exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm]) [ 19.704418] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm]) [ 19.717935] exynos-drm exynos-drm: bound 14500000.dsi (ops exynos_dsi_component_ops [exynosdrm]) [ 19.725549] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops [exynosdrm]) [ 19.734421] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 19.740789] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 19.748380] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1 [ 19.865546] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 19.893554] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 19.937531] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 20.014739] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 20.022259] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 20.029418] usb 1-3.2: Product: USB2.0 Hub [ 20.036034] hub 1-3.2:1.0: USB hub found [ 20.039166] hub 1-3.2:1.0: 4 ports detected [ 20.052586] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 20.160584] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 20.271610] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 20.337569] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 20.379525] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 20.387405] Buffer I/O error on dev mmcblk0, logical block 967954, async page read [ 20.455015] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 20.462136] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 20.469602] usb 1-3.2.4: Product: AX88772 [ 20.473677] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 20.478891] usb 1-3.2.4: SerialNumber: 000001 [ 21.016934] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 21.684056] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 21.699601] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 21.713365] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, f2:80:02:35:6b:18 [ 21.725691] usbcore: registered new interface driver asix [ 22.525271] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 24.337298] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 24.389290] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 24.625973] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 25.855612] audit: type=1400 audit(1718375629.260:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=900 comm="apparmor_parser" [ 25.870039] audit: type=1400 audit(1718375629.264:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=901 comm="apparmor_parser" [ 25.884423] audit: type=1400 audit(1718375629.264:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=901 comm="apparmor_parser" [ 25.942229] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 26.219869] audit: type=1400 audit(1718375629.624:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=943 comm="apparmor_parser" [ 26.239416] audit: type=1400 audit(1718375629.640:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=943 comm="apparmor_parser" [ 26.252864] audit: type=1400 audit(1718375629.644:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=943 comm="apparmor_parser" [ 26.533966] audit: type=1400 audit(1718375629.940:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=942 comm="apparmor_parser" [ 26.550840] audit: type=1400 audit(1718375629.940:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=942 comm="apparmor_parser" [ 26.567753] audit: type=1400 audit(1718375629.940:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=942 comm="apparmor_parser" [ 26.585256] audit: type=1400 audit(1718375629.940:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=942 comm="apparmor_parser" [ 28.103139] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 28.109212] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready