[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc3+ (osstest@himrod2) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Fri Jun 14 19:16:51 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off, mlocked free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6080K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000012] Switching to timer-based delay loop, resolution 41ns [ 0.000517] Console: colour dummy device 80x30 [ 0.000535] printk: legacy console [hvc0] enabled [ 0.300747] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.311145] CPU: Testing write buffer coherency: ok [ 0.316087] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.325641] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.332053] pid_max: default: 32768 minimum: 301 [ 0.336840] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.344140] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.352521] /cpus/cpu@0 missing clock-frequency property [ 0.357324] /cpus/cpu@1 missing clock-frequency property [ 0.362719] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.369435] xen:grant_table: Grant tables using version 1 layout [ 0.374573] Grant table initialized [ 0.378125] xen:events: Using FIFO-based ABI [ 0.382426] Xen: initializing cpu0 [ 0.385949] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.393746] rcu: Hierarchical SRCU implementation. [ 0.397345] rcu: Max phase no-delay instances is 1000. [ 0.405568] EFI services will not be available. [ 0.408887] smp: Bringing up secondary CPUs ... [ 0.483097] Xen: initializing cpu1 [ 0.483255] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.483278] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.502260] smp: Brought up 1 node, 2 CPUs [ 0.505914] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.512202] CPU: All CPU(s) started in SVC mode. [ 0.518118] devtmpfs: initialized [ 0.530699] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.537255] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.546925] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.554843] pinctrl core: initialized pinctrl subsystem [ 0.561455] DMI not present or invalid. [ 0.564970] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.571583] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.580954] thermal_sys: Registered thermal governor 'step_wise' [ 0.581114] software IO TLB: area num 2. [ 0.589787] software IO TLB: only able to allocate 8 MB [ 0.596860] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.602066] No ATAGs? [ 0.604365] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.613110] Serial: AMBA PL011 UART driver [ 0.659873] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.688348] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.712167] xen:balloon: Initialising balloon driver [ 0.718622] iommu: Default domain type: Translated [ 0.722037] iommu: DMA domain TLB invalidation policy: strict mode [ 0.730851] SCSI subsystem initialized [ 0.733390] libata version 3.00 loaded. [ 0.733618] usbcore: registered new interface driver usbfs [ 0.738839] usbcore: registered new interface driver hub [ 0.744192] usbcore: registered new device driver usb [ 0.750912] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.754504] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.760767] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.765825] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.770755] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.776794] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.782598] pps_core: LinuxPPS API ver. 1 registered [ 0.786963] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.796194] PTP clock support registered [ 0.800413] EDAC MC: Ver: 3.0.0 [ 0.803687] scmi_core: SCMI protocol bus registered [ 0.818586] vgaarb: loaded [ 0.821471] clocksource: Switched to clocksource arch_sys_counter [ 0.835844] NET: Registered PF_INET protocol family [ 0.839487] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.847412] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.855084] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.862888] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.870727] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.878012] TCP: Hash tables configured (established 4096 bind 4096) [ 0.884373] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.890940] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.898049] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.904203] RPC: Registered named UNIX socket transport module. [ 0.909657] RPC: Registered udp transport module. [ 0.914449] RPC: Registered tcp transport module. [ 0.919203] RPC: Registered tcp-with-tls transport module. [ 0.924773] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.931274] PCI: CLS 0 bytes, default 64 [ 0.936725] Initialise system trusted keyrings [ 0.940038] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.946567] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.952462] Trying to unpack rootfs image as initramfs... [ 0.983399] NFS: Registering the id_resolver key type [ 0.987122] Key type id_resolver registered [ 0.991356] Key type id_legacy registered [ 0.995481] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.002211] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.023175] Key type asymmetric registered [ 1.025916] Asymmetric key parser 'x509' registered [ 1.030939] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.038369] io scheduler mq-deadline registered [ 1.042943] io scheduler kyber registered [ 1.047036] io scheduler bfq registered [ 1.174309] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.180523] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.228356] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.234598] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.262234] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.268437] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.314061] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.320287] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.332691] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.392904] xen:xen_evtchn: Event-channel device installed [ 1.492192] Freeing initrd memory: 11856K [ 1.601981] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.613059] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.621256] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.630183] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.639140] SuperH (H)SCI(F) driver initialized [ 1.643484] STMicroelectronics ASC driver initialized [ 1.648325] STM32 USART driver initialized [ 1.656335] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.665101] random: crng init done [ 1.672865] brd: module loaded [ 1.678761] loop: module loaded [ 1.714007] Invalid max_queues (4), will use default max: 2. [ 1.733004] tun: Universal TUN/TAP device driver, 1.6 [ 1.736860] CAN device driver interface [ 1.742093] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.753423] xen_netfront: Initialising Xen virtual ethernet driver [ 1.758282] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.763905] usbcore: registered new interface driver pegasus [ 1.769623] usbcore: registered new interface driver asix [ 1.775097] usbcore: registered new interface driver ax88179_178a [ 1.781264] usbcore: registered new interface driver cdc_ether [ 1.787203] usbcore: registered new interface driver smsc75xx [ 1.793001] usbcore: registered new interface driver smsc95xx [ 1.798782] usbcore: registered new interface driver net1080 [ 1.804524] usbcore: registered new interface driver cdc_subset [ 1.810501] usbcore: registered new interface driver zaurus [ 1.816164] usbcore: registered new interface driver cdc_ncm [ 1.825700] usbcore: registered new interface driver usb-storage [ 1.836426] i2c_dev: i2c /dev entries driver [ 1.855468] device-mapper: uevent: version 1.0.3 [ 1.858895] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.868536] cpu cpu0: OPP table can't be empty [ 1.873253] failed to register cpuidle driver [ 1.876593] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.884954] sdhci: Secure Digital Host Controller Interface driver [ 1.889958] sdhci: Copyright(c) Pierre Ossman [ 1.898113] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.905955] ledtrig-cpu: registered to indicate activity on CPUs [ 1.911386] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.918115] usbcore: registered new interface driver usbhid [ 1.922765] usbhid: USB HID core driver [ 1.933798] NET: Registered PF_INET6 protocol family [ 1.938298] Segment Routing with IPv6 [ 1.941144] In-situ OAM (IOAM) with IPv6 [ 1.945224] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.951665] NET: Registered PF_PACKET protocol family [ 1.956232] can: controller area network core [ 1.960683] NET: Registered PF_CAN protocol family [ 1.965550] can: raw protocol [ 1.968551] can: broadcast manager protocol [ 1.972838] can: netlink gateway - max_hops=1 [ 1.977546] Key type dns_resolver registered [ 1.982279] ThumbEE CPU extension supported. [ 1.985914] Registering SWP/SWPB emulation handler [ 2.000360] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.007273] Loading compiled-in X.509 certificates [ 2.050012] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.053679] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.061123] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.068699] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.110151] s5m-rtc s5m-rtc: registered as rtc0 [ 2.119057] s5m-rtc s5m-rtc: setting system clock to 2024-06-15T00:48:37 UTC (1718412517) [ 2.130112] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.134794] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.139087] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.145958] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.151783] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.157933] clk: Not disabling unused clocks [ 2.161520] PM: genpd: Disabling unused power domains [ 2.169957] Freeing unused kernel image (initmem) memory: 2048K [ 2.176245] Run /init as init process [ 2.178524] with arguments: [ 2.178530] /init [ 2.178537] with environment: [ 2.178542] HOME=/ [ 2.178547] TERM=linux [ 3.445864] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.584969] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.625782] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.656147] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.689851] Synopsys Designware Multimedia Card Interface Driver [ 3.712050] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.721823] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.726925] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.728641] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.732495] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 125,32 bit host data width,128 deep fifo [ 3.739399] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.749720] mmc_host mmc0: card is polling. [ 3.754543] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.759620] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.792818] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.804911] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.811151] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.821619] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.842487] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.847564] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.853153] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.862847] exynos-ehci 12110000.usb: irq 126, io mem 0x12110000 [ 3.869073] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.875871] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.884665] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.891511] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.904381] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.911809] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.959419] hub 1-0:1.0: USB hub found [ 3.984669] hub 1-0:1.0: 3 ports detected [ 3.988440] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.000423] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 4.006122] exynos-ohci 12120000.usb: USB Host Controller [ 4.011566] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 4.019504] scsi host0: ahci-dwc [ 4.022963] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 4.032839] exynos-ohci 12120000.usb: irq 126, io mem 0x12120000 [ 4.117338] hub 2-0:1.0: USB hub found [ 4.120239] hub 2-0:1.0: 3 ports detected [ 4.123907] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.134431] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.139469] mmc0: new DDR MMC card at address 0001 [ 4.140325] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.144938] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.159613] mmcblk0: p1 p2 p3 p4 [ 4.164713] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.172500] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.180585] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.199852] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.208490] mmc1: new high speed SDHC card at address aaaa [ 4.214381] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.531503] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.537364] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.543128] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.550887] ata1.00: configured for UDMA/133 [ 4.554360] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.563610] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.569740] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.575186] sd 0:0:0:0: [sda] Write Protect is off [ 4.579894] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.579975] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.589165] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.626397] sda: sda1 sda2 < sda5 > [ 4.629380] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.149804] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 5.158108] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.162309] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.183478] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 5.191783] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 5.197777] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.203208] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.210877] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.218674] hub 3-0:1.0: USB hub found [ 5.221596] hub 3-0:1.0: 1 port detected [ 5.226393] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.234471] hub 4-0:1.0: USB hub found [ 5.237502] hub 4-0:1.0: 1 port detected [ 5.377902] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.520324] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.629033] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.737177] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.845304] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.953445] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.061554] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.169625] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.277714] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.385824] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.794583] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.902341] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7.510733] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 11.037018] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.333316] EXT4-fs (dm-0): mounted filesystem 9499a42e-4cc5-4a46-b942-b4966095f7e2 ro with ordered data mode. Quota mode: disabled. [ 15.099113] s5p-secss 10830000.sss: s5p-sss driver registered [ 15.117656] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.129356] mc: Linux media interface: v0.10 [ 15.304393] videodev: Linux video capture interface: v2.00 [ 15.425721] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 15.486192] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.504513] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.516835] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.524221] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.537835] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.539263] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 15.552676] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 15.638721] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 15.645155] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 15.650839] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 15.656597] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 15.718441] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.830724] blk_print_req_error: 6 callbacks suppressed [ 15.830737] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.881798] usb3503 usb-hub: switched to HUB mode [ 15.885150] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.963227] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.072904] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.180983] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.252949] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.290371] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.313008] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 16.346027] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 16.354770] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 16.400521] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.508609] hub 1-3:1.0: USB hub found [ 16.511720] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.528648] hub 1-3:1.0: 3 ports detected [ 16.620754] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.700950] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.708712] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.717427] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.728429] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.737065] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.745692] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.961517] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.057378] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.125084] hub 1-3.2:1.0: USB hub found [ 17.128044] hub 1-3.2:1.0: 4 ports detected [ 17.160361] usbcore: registered new device driver onboard-usb-dev [ 17.165174] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.294214] hub 1-3.2:1.0: USB hub found [ 17.297168] hub 1-3.2:1.0: 4 ports detected [ 17.310097] hub 1-3.2:1.0: USB hub found [ 17.313106] hub 1-3.2:1.0: 4 ports detected [ 17.631502] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.775026] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 17.785691] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.215240] EXT4-fs (dm-0): re-mounted 9499a42e-4cc5-4a46-b942-b4966095f7e2 r/w. Quota mode: disabled. [ 18.533555] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.548046] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.557966] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 92:f2:80:0b:02:cc [ 20.328642] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.377489] EXT4-fs (sda1): mounted filesystem f753cd5f-232f-4012-bf5c-a1c339b92398 r/w with ordered data mode. Quota mode: disabled. [ 20.472743] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 22.184275] xenbr0: port 1(eth0) entered blocking state [ 22.188140] xenbr0: port 1(eth0) entered disabled state [ 22.193507] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 22.199330] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 22.210199] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.410076] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 24.416130] xenbr0: port 1(eth0) entered blocking state [ 24.421313] xenbr0: port 1(eth0) entered forwarding state