[ 0.000000] Linux version 6.10.0-rc3+ (osstest@himrod2) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Sun Jun 16 07:57:32 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/pinot0--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000099fff] usable [ 0.000000] Xen: [mem 0x000000000009a800-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020065fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000f6000000-0x00000000f6003fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SML/H8SML, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 2/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000011] Xen PV: Detected 4 vCPUS [ 0.038443] tsc: Fast TSC calibration using PIT [ 0.038444] tsc: Detected 2799.972 MHz processor [ 0.038446] tsc: Detected 2799.986 MHz TSC [ 0.038662] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.038666] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.038673] last_pfn = 0x20066 max_arch_pfn = 0x400000000 [ 0.038676] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.038679] MTRRs set to read-only [ 0.038681] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.064684] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.064707] ACPI: Early table checksum verification disabled [ 0.065815] ACPI: RSDP 0x00000000000FA1C0 000024 (v02 ACPIAM) [ 0.065826] ACPI: XSDT 0x00000000DFEA0100 00007C (v01 SMCI 20131125 MSFT 00000097) [ 0.065861] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.065908] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.065920] ACPI: DSDT 0x00000000DFEA0600 00562B (v01 1CF11 1CF11000 00000000 INTL 20051117) [ 0.065931] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.065941] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.065952] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.065963] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.065974] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.065984] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.065995] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.066006] ACPI: SSDT 0x00000000DFEAA6F0 000B9C (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.066017] ACPI: EINJ 0x00000000DFEAB290 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.066027] ACPI: BERT 0x00000000DFEAB420 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.066038] ACPI: ERST 0x00000000DFEAB450 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.066048] ACPI: HEST 0x00000000DFEAB660 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.066054] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.066056] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c2a] [ 0.066057] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.066059] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.066060] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.066062] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.066063] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.066064] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.066065] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.066067] ACPI: Reserving SSDT table memory at [mem 0xdfeaa6f0-0xdfeab28b] [ 0.066068] ACPI: Reserving EINJ table memory at [mem 0xdfeab290-0xdfeab3bf] [ 0.066069] ACPI: Reserving BERT table memory at [mem 0xdfeab420-0xdfeab44f] [ 0.066070] ACPI: Reserving ERST table memory at [mem 0xdfeab450-0xdfeab65f] [ 0.066072] ACPI: Reserving HEST table memory at [mem 0xdfeab660-0xdfeab707] [ 0.066200] APIC: Switched APIC routing to: Xen PV [ 0.068594] Zone ranges: [ 0.068597] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.068599] DMA32 [mem 0x0000000001000000-0x0000000020065fff] [ 0.068602] Normal empty [ 0.068603] Movable zone start for each node [ 0.068604] Early memory node ranges [ 0.068604] node 0: [mem 0x0000000000001000-0x0000000000099fff] [ 0.068607] node 0: [mem 0x0000000000100000-0x0000000020065fff] [ 0.068609] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020065fff] [ 0.068621] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.068714] On node 0, zone DMA: 102 pages in unavailable ranges [ 0.072750] On node 0, zone DMA32: 32666 pages in unavailable ranges [ 0.072763] p2m virtual area at (____ptrval____), size is 40000000 [ 0.293233] Remapped 102 page(s) [ 0.293759] ACPI: PM-Timer IO Port: 0x808 [ 0.293794] CPU topo: CPU limit of 4 reached. Ignoring further CPUs [ 0.293824] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.293827] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.293850] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.293858] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.293870] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.293875] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.293897] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.293901] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.293913] CPU topo: Max. logical packages: 1 [ 0.293914] CPU topo: Max. logical dies: 1 [ 0.293915] CPU topo: Max. dies per package: 1 [ 0.293923] CPU topo: Max. threads per core: 1 [ 0.293924] CPU topo: Num. cores per package: 4 [ 0.293925] CPU topo: Num. threads per package: 4 [ 0.293926] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.293927] CPU topo: Rejected CPUs 4 [ 0.293945] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.293948] PM: hibernation: Registered nosave memory: [mem 0x0009a000-0x0009afff] [ 0.293950] PM: hibernation: Registered nosave memory: [mem 0x0009b000-0x000fffff] [ 0.293952] [mem 0x20066000-0xdfe9dfff] available for PCI devices [ 0.293957] Booting kernel on Xen [ 0.293958] Xen version: 4.19-unstable (preserve-AD) [ 0.293963] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.300391] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.301323] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.301333] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.301338] pcpu-alloc: [0] 0 1 2 3 [ 0.301415] xen: PV spinlocks enabled [ 0.301420] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.301423] Kernel command line: placeholder root=/dev/mapper/pinot0--vg-root ro console=hvc0 [ 0.301502] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.301717] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.301819] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.302028] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.302033] mem auto-init: stack:all(zero), heap alloc:off, heap free:off, mlocked free:off [ 0.302037] software IO TLB: area num 4. [ 0.408371] Memory: 386444K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137588K reserved, 0K cma-reserved) [ 0.408492] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.411344] Dynamic Preempt: voluntary [ 0.411459] rcu: Preemptible hierarchical RCU implementation. [ 0.411460] rcu: RCU event tracing is enabled. [ 0.411461] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.411463] Trampoline variant of Tasks RCU enabled. [ 0.411464] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.411466] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.411485] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.418307] NR_IRQS: 4352, nr_irqs: 1000, preallocated irqs: 16 [ 0.418466] xen:events: Using FIFO-based ABI [ 0.418497] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.418503] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.418509] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.418514] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.418519] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.418524] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.418530] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.418534] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.418542] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.418547] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.418553] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.418558] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.418564] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.418569] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.418574] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.418585] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.424728] Console: colour VGA+ 80x25 [ 0.424733] printk: legacy console [tty0] enabled [ 0.438491] printk: legacy console [hvc0] enabled [ 0.439162] ACPI: Core revision 20240322 [ 0.443229] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.443386] Xen: using vcpuop timer interface [ 0.443391] installing Xen timer for CPU 0 [ 0.443634] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x285c335c9f5, max_idle_ns: 440795236380 ns [ 0.443794] Calibrating delay loop (skipped), value calculated using timer frequency.. 5599.97 BogoMIPS (lpj=2799986) [ 0.443986] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.444231] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.444340] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.444455] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.444803] Spectre V2 : Mitigation: Retpolines [ 0.444906] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.445049] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.445159] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.445268] RETBleed: Mitigation: untrained return thunk [ 0.445374] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.445518] Speculative Store Bypass: Vulnerable [ 0.445666] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.445795] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.445904] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.446015] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.446125] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.471690] Freeing SMP alternatives memory: 40K [ 0.471799] pid_max: default: 32768 minimum: 301 [ 0.471955] LSM: initializing lsm=capability,selinux [ 0.472066] SELinux: Initializing. [ 0.472218] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.472391] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.473925] cpu 0 spinlock event irq 57 [ 0.474038] VPMU disabled by hypervisor. [ 0.474538] Performance Events: PMU not available due to virtualization, using software events only. [ 0.474798] signal: max sigframe size: 1776 [ 0.474957] rcu: Hierarchical SRCU implementation. [ 0.475061] rcu: Max phase no-delay instances is 400. [ 0.481014] smp: Bringing up secondary CPUs ... [ 0.481340] installing Xen timer for CPU 1 [ 0.481839] installing Xen timer for CPU 2 [ 0.482248] installing Xen timer for CPU 3 [ 0.026200] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.482941] cpu 1 spinlock event irq 77 [ 0.026200] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.483886] cpu 2 spinlock event irq 78 [ 0.026200] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.484130] cpu 3 spinlock event irq 79 [ 0.485006] smp: Brought up 1 node, 4 CPUs [ 0.486329] devtmpfs: initialized [ 0.486329] x86/mm: Memory block size: 128MB [ 0.486871] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.487219] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.487577] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.488015] PM: RTC time: 09:13:32, date: 2024-06-16 [ 0.488529] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.488907] xen:grant_table: Grant tables using version 1 layout [ 0.489296] Grant table initialized [ 0.491033] audit: initializing netlink subsys (disabled) [ 0.491850] audit: type=2000 audit(1718529212.181:1): state=initialized audit_enabled=0 res=1 [ 0.493069] thermal_sys: Registered thermal governor 'step_wise' [ 0.493080] thermal_sys: Registered thermal governor 'user_space' [ 0.493939] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.494197] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.746264] PCI: Using configuration type 1 for base access [ 0.747978] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.749018] ACPI: Added _OSI(Module Device) [ 0.749018] ACPI: Added _OSI(Processor Device) [ 0.749096] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.749352] ACPI: Added _OSI(Processor Aggregator Device) [ 0.757395] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.757790] xen: registering gsi 9 triggering 0 polarity 1 [ 0.763973] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.765058] ACPI: Interpreter enabled [ 0.765192] ACPI: PM: (supports S0 S1 S4 S5) [ 0.765303] ACPI: Using IOAPIC for interrupt routing [ 0.765477] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.765659] PCI: Using E820 reservations for host bridge windows [ 0.765972] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.778180] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.778307] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.778477] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.778596] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.778744] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.779121] PCI host bridge to bus 0000:00 [ 0.779238] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.779357] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.779475] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.779624] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.779781] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.779935] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.780131] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.780754] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.781254] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.781489] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.781616] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.781739] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.781856] pci 0000:00:09.0: enabling Extended Tags [ 0.782109] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.782447] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.782683] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.782810] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.782933] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.783112] pci 0000:00:0a.0: enabling Extended Tags [ 0.783363] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.783713] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f conventional PCI endpoint [ 0.783844] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.783983] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.784122] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.784260] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.784398] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.784538] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.784742] pci 0000:00:11.0: set SATA to AHCI mode [ 0.785041] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.785243] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.785669] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.785871] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.786371] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.786573] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.786948] pci 0000:00:12.2: supports D1 D2 [ 0.787080] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.787377] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.787580] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.788045] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.788270] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.788718] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.788845] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.789229] pci 0000:00:13.2: supports D1 D2 [ 0.789339] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.789680] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.790219] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.790434] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.790599] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.790737] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.790821] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.790960] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.791134] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.791252] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.791369] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.791487] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.791859] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.792409] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.792660] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.792798] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.792958] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.793278] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.793481] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.793930] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.794327] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.794701] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.794998] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.795394] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.795742] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.796179] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.796386] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.796583] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.796726] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.797124] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.797589] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.797911] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.798118] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.798339] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.798483] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.798908] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.801835] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.802014] pci_bus 0000:03: extended config space not accessible [ 0.802192] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.802430] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.802579] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.802723] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.802939] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.803366] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.803507] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.803795] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.803948] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.804103] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.804258] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.804490] pci_bus 0000:00: on NUMA node 0 [ 0.805047] xen: registering gsi 13 triggering 1 polarity 0 [ 0.805550] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.805750] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.805879] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.806076] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.806273] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.806508] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.806699] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.806867] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.807136] xen:balloon: Initialising balloon driver [ 0.807266] iommu: Default domain type: Translated [ 0.807796] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.808020] SCSI subsystem initialized [ 0.808164] libata version 3.00 loaded. [ 0.808164] ACPI: bus type USB registered [ 0.808164] usbcore: registered new interface driver usbfs [ 0.808164] usbcore: registered new interface driver hub [ 0.808804] usbcore: registered new device driver usb [ 0.808938] pps_core: LinuxPPS API ver. 1 registered [ 0.809049] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.809231] PTP clock support registered [ 0.809385] Advanced Linux Sound Architecture Driver Initialized. [ 0.810155] NetLabel: Initializing [ 0.810261] NetLabel: domain hash size = 128 [ 0.810370] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.810537] NetLabel: unlabeled traffic allowed by default [ 0.810808] PCI: Using ACPI for IRQ routing [ 0.841158] PCI: pci_cache_line_size set to 64 bytes [ 0.841354] e820: reserve RAM buffer [mem 0x0009a000-0x0009ffff] [ 0.841358] e820: reserve RAM buffer [mem 0x20066000-0x23ffffff] [ 0.841385] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.841385] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.841385] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.841795] vgaarb: loaded [ 0.843617] clocksource: Switched to clocksource tsc-early [ 0.843742] VFS: Disk quotas dquot_6.6.0 [ 0.843742] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.843742] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.843742] pnp: PnP ACPI init [ 0.843894] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.843981] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.843981] xen: registering gsi 8 triggering 1 polarity 0 [ 0.844947] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.845275] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.845397] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.845918] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.846062] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.846178] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.846295] system 00:05: [io 0x040b] has been reserved [ 0.846408] system 00:05: [io 0x04d6] has been reserved [ 0.846522] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.846637] system 00:05: [io 0x0c14] has been reserved [ 0.846773] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.846898] system 00:05: [io 0x0c52] has been reserved [ 0.847011] system 00:05: [io 0x0c6c] has been reserved [ 0.847123] system 00:05: [io 0x0c6f] has been reserved [ 0.847261] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.847376] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.847491] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.847607] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.847722] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.847846] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.847961] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.848082] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.848204] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.848319] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.848448] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.848564] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.848681] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.848808] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.849205] xen: registering gsi 4 triggering 1 polarity 0 [ 0.849209] Already setup the GSI :4 [ 0.849315] pnp 00:06: [dma 0 disabled] [ 0.849693] xen: registering gsi 3 triggering 1 polarity 0 [ 0.849704] pnp 00:07: [dma 0 disabled] [ 0.849889] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.850296] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.850492] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.850613] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.850732] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.850923] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.851217] pnp: PnP ACPI: found 10 devices [ 0.874660] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.874850] NET: Registered PF_INET protocol family [ 0.875041] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.875498] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.875654] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.875882] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.876092] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.876288] TCP: Hash tables configured (established 4096 bind 4096) [ 0.876453] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.876601] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.876763] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.877212] RPC: Registered named UNIX socket transport module. [ 0.877330] RPC: Registered udp transport module. [ 0.877439] RPC: Registered tcp transport module. [ 0.877548] RPC: Registered tcp-with-tls transport module. [ 0.877659] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.878412] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.878565] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.878694] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.878851] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.878991] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.879117] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.879257] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.879379] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.879506] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.879672] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.879789] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.879914] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.880058] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.880204] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.880322] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.880435] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.880550] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.880663] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.880780] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.880904] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.881023] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.881139] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.881254] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.881409] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.881528] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.881865] xen: registering gsi 16 triggering 0 polarity 1 [ 0.881921] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.544993] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 647700 usecs [ 1.545250] xen: registering gsi 16 triggering 0 polarity 1 [ 1.545262] Already setup the GSI :16 [ 1.570008] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 24239 usecs [ 1.570271] xen: registering gsi 17 triggering 0 polarity 1 [ 1.570336] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.570546] xen: registering gsi 18 triggering 0 polarity 1 [ 1.570567] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.595010] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23947 usecs [ 1.595270] xen: registering gsi 18 triggering 0 polarity 1 [ 1.595281] Already setup the GSI :18 [ 1.619994] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 24207 usecs [ 1.620261] xen: registering gsi 19 triggering 0 polarity 1 [ 1.620321] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.620553] xen: registering gsi 18 triggering 0 polarity 1 [ 1.620557] Already setup the GSI :18 [ 1.644996] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 23926 usecs [ 1.645239] PCI: CLS 64 bytes, default 64 [ 1.645399] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.645514] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 1.645691] Unpacking initramfs... [ 1.645733] kvm_intel: VMX not supported by CPU 0 [ 1.645943] kvm_amd: SVM not supported by CPU 0 [ 1.646056] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x285c335c9f5, max_idle_ns: 440795236380 ns [ 1.646407] clocksource: Switched to clocksource tsc [ 1.704231] Initialise system trusted keyrings [ 1.705061] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.705548] NFS: Registering the id_resolver key type [ 1.705662] Key type id_resolver registered [ 1.705763] Key type id_legacy registered [ 1.705935] 9p: Installing v9fs 9p2000 file system support [ 1.737331] Key type asymmetric registered [ 1.737681] Asymmetric key parser 'x509' registered [ 1.738100] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.738547] io scheduler mq-deadline registered [ 1.738798] io scheduler kyber registered [ 1.740320] xen: registering gsi 53 triggering 0 polarity 1 [ 1.740459] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.742060] xen: registering gsi 54 triggering 0 polarity 1 [ 1.742182] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.744539] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.745123] ACPI: button: Power Button [PWRB] [ 1.745630] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.746369] ACPI: button: Power Button [PWRF] [ 1.749297] ACPI: \_PR_.P001: Found 2 idle states [ 1.749833] ACPI: \_PR_.P002: Found 2 idle states [ 1.750380] ACPI: \_PR_.P003: Found 2 idle states [ 1.750836] ACPI: \_PR_.P004: Found 2 idle states [ 1.752517] xen:xen_evtchn: Event-channel device installed [ 1.752756] xen_pciback: backend is vpci [ 1.755013] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.755608] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.758099] hpet_acpi_add: no address or irqs in _CRS [ 1.758538] Non-volatile memory driver v1.3 [ 1.768028] loop: module loaded [ 1.790555] ahci 0000:00:11.0: version 3.0 [ 1.790703] xen: registering gsi 22 triggering 0 polarity 1 [ 1.790741] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.790921] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.791078] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.791189] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.792773] scsi host0: ahci [ 1.793248] scsi host1: ahci [ 1.793660] scsi host2: ahci [ 1.794417] scsi host3: ahci [ 1.795070] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.795444] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.795801] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.796146] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.797158] tun: Universal TUN/TAP device driver, 1.6 [ 1.797429] e100: Intel(R) PRO/100 Network Driver [ 1.797534] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.797673] sky2: driver version 1.30 [ 1.798047] xen_netfront: Initialising Xen virtual ethernet driver [ 1.799242] xen: registering gsi 17 triggering 0 polarity 1 [ 1.799252] Already setup the GSI :17 [ 1.799296] xen: registering gsi 16 triggering 0 polarity 1 [ 1.799343] xen: registering gsi 19 triggering 0 polarity 1 [ 1.799350] Already setup the GSI :19 [ 1.799484] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.799486] Already setup the GSI :16 [ 1.800242] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 1 [ 1.800615] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.801065] ehci-pci 0000:00:13.2: debug port 1 [ 1.801449] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.809249] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.809754] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.809931] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.810078] usb usb1: Product: EHCI Host Controller [ 1.810242] usb usb1: Manufacturer: Linux 6.10.0-rc3+ ehci_hcd [ 1.810356] usb usb1: SerialNumber: 0000:00:13.2 [ 1.810988] hub 1-0:1.0: USB hub found [ 1.811131] hub 1-0:1.0: 6 ports detected [ 1.811566] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.811792] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 2 [ 1.812035] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.867413] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.867594] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.867735] usb usb2: Product: OHCI PCI host controller [ 1.867843] usb usb2: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.867953] usb usb2: SerialNumber: 0000:00:12.0 [ 1.868315] hub 2-0:1.0: USB hub found [ 1.868497] hub 2-0:1.0: 3 ports detected [ 1.868939] xen: registering gsi 16 triggering 0 polarity 1 [ 1.868947] Already setup the GSI :16 [ 1.869074] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.869470] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 3 [ 1.869847] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.870246] ehci-pci 0000:00:12.2: debug port 1 [ 1.870478] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.877261] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.877768] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.877945] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.878094] usb usb3: Product: EHCI Host Controller [ 1.878252] usb usb3: Manufacturer: Linux 6.10.0-rc3+ ehci_hcd [ 1.878371] usb usb3: SerialNumber: 0000:00:12.2 [ 1.878961] hub 3-0:1.0: USB hub found [ 1.879119] hub 3-0:1.0: 6 ports detected [ 1.906730] Freeing initrd memory: 20192K [ 1.931467] hub 2-0:1.0: USB hub found [ 1.931668] hub 2-0:1.0: 3 ports detected [ 1.932811] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.933353] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.933556] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.989472] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.989646] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.989786] usb usb4: Product: OHCI PCI host controller [ 1.989891] usb usb4: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 1.989999] usb usb4: SerialNumber: 0000:00:12.1 [ 1.990357] hub 4-0:1.0: USB hub found [ 1.990511] hub 4-0:1.0: 3 ports detected [ 1.990975] xen: registering gsi 18 triggering 0 polarity 1 [ 1.990984] Already setup the GSI :18 [ 1.991140] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.991378] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.991603] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 2.047351] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.047513] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.047653] usb usb5: Product: OHCI PCI host controller [ 2.047758] usb usb5: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 2.047864] usb usb5: SerialNumber: 0000:00:13.0 [ 2.048171] hub 5-0:1.0: USB hub found [ 2.048310] hub 5-0:1.0: 3 ports detected [ 2.048781] xen: registering gsi 18 triggering 0 polarity 1 [ 2.048788] Already setup the GSI :18 [ 2.048933] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 2.049127] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 2.049341] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 2.105315] ata4: SATA link down (SStatus 0 SControl 300) [ 2.105469] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.105569] ata3: SATA link down (SStatus 0 SControl 300) [ 2.105674] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.105923] usb usb6: Product: OHCI PCI host controller [ 2.106027] usb usb6: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 2.106134] usb usb6: SerialNumber: 0000:00:13.1 [ 2.106428] hub 6-0:1.0: USB hub found [ 2.106563] hub 6-0:1.0: 3 ports detected [ 2.107085] xen: registering gsi 18 triggering 0 polarity 1 [ 2.107091] Already setup the GSI :18 [ 2.107252] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 2.107465] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 2.107671] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 2.163358] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.163507] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.163646] usb usb7: Product: OHCI PCI host controller [ 2.163751] usb usb7: Manufacturer: Linux 6.10.0-rc3+ ohci_hcd [ 2.163897] usb usb7: SerialNumber: 0000:00:14.5 [ 2.164172] hub 7-0:1.0: USB hub found [ 2.164297] hub 7-0:1.0: 2 ports detected [ 2.164607] usbcore: registered new interface driver usblp [ 2.164737] usbcore: registered new interface driver usb-storage [ 2.164882] i8042: PNP: No PS/2 controller found. [ 2.164984] i8042: Probing ports directly. [ 2.168189] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.168309] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.168627] rtc_cmos 00:02: RTC can wake from S4 [ 2.169170] rtc_cmos 00:02: registered as rtc0 [ 2.169353] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 2.169523] device-mapper: uevent: version 1.0.3 [ 2.169701] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 2.169853] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 2.170010] hid: raw HID events driver (C) Jiri Kosina [ 2.170342] usbcore: registered new interface driver usbhid [ 2.170448] usbhid: USB HID core driver [ 2.170941] Initializing XFRM netlink socket [ 2.171094] NET: Registered PF_INET6 protocol family [ 2.171621] Segment Routing with IPv6 [ 2.171734] In-situ OAM (IOAM) with IPv6 [ 2.171868] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.172126] NET: Registered PF_PACKET protocol family [ 2.172299] 9pnet: Installing 9P2000 support [ 2.172421] Key type dns_resolver registered [ 2.172536] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 2.173021] IPI shorthand broadcast: enabled [ 2.177540] sched_clock: Marking stable (2152005402, 25200439)->(2190804611, -13598770) [ 2.178023] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.178319] registered taskstats version 1 [ 2.178420] Loading compiled-in X.509 certificates [ 2.180551] PM: Magic number: 12:323:222 [ 2.180710] printk: legacy console [netcon0] enabled [ 2.180815] netconsole: network logging started [ 2.181022] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.191458] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.191847] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.192004] ALSA device list: [ 2.194308] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 2.194489] No soundcards found. [ 2.259274] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.259433] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.260122] ata2.00: ATA-9: WDC WD1003FZEX-00MK2A0, 01.01A01, max UDMA/133 [ 2.260701] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 2.260948] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 2.261377] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 2.261825] ata2.00: configured for UDMA/133 [ 2.263270] ata1.00: configured for UDMA/133 [ 2.263532] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 2.264060] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.264087] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.264365] sd 0:0:0:0: [sda] Write Protect is off [ 2.264481] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.264495] scsi 1:0:0:0: Direct-Access ATA WDC WD1003FZEX-0 1A01 PQ: 0 ANSI: 5 [ 2.264512] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.264828] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 2.265001] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 2.265179] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.265351] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 2.265496] sd 1:0:0:0: [sdb] Write Protect is off [ 2.265600] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.265622] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.265806] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 2.289939] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.294642] sda: sda1 sda2 < sda5 > [ 2.295017] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.296616] Freeing unused kernel image (initmem) memory: 2680K [ 2.296747] Write protecting the kernel read-only data: 24576k [ 2.309301] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.355246] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.424985] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.425138] Run /init as init process [ 2.425258] with arguments: [ 2.425259] /init [ 2.425265] placeholder [ 2.425266] with environment: [ 2.425268] HOME=/ [ 2.425269] TERM=linux [ 2.518352] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.518511] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.518624] usb 6-2: Product: Hermon USB hidmouse Device [ 2.518730] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.524813] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.525155] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.528767] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.580551] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.700231] e1000e: Intel(R) PRO/1000 Network Driver [ 2.700395] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.700660] xen: registering gsi 48 triggering 0 polarity 1 [ 2.700703] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.700923] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.745052] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.789054] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e8:ac [ 2.789254] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.789445] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.789676] xen: registering gsi 47 triggering 0 polarity 1 [ 2.789702] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.789891] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.837286] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.882153] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e8:ad [ 2.882317] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.882541] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.884565] e1000e 0000:01:00.0 enx002590aee8ac: renamed from eth0 [ 2.885150] e1000e 0000:02:00.0 enx002590aee8ad: renamed from eth1 [ 2.889241] random: crng init done [ 3.550175] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.555671] EXT4-fs (dm-0): mounted filesystem 0460cf8b-ec98-494e-b2f5-f7a969c7312a ro with ordered data mode. Quota mode: none. [ 8.044029] EXT4-fs (dm-0): re-mounted 0460cf8b-ec98-494e-b2f5-f7a969c7312a r/w. Quota mode: none. [ 9.570566] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 9.585159] EXT4-fs (sda1): mounted filesystem bc549f1e-f2a2-4893-b8a0-0a7f8cc4275c r/w with ordered data mode. Quota mode: none. [ 9.665395] Adding 1949692k swap on /dev/mapper/pinot0--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 11.311080] xenbr0: port 1(enx002590aee8ac) entered blocking state [ 11.311245] xenbr0: port 1(enx002590aee8ac) entered disabled state [ 11.311362] e1000e 0000:01:00.0 enx002590aee8ac: entered allmulticast mode [ 11.311520] e1000e 0000:01:00.0 enx002590aee8ac: entered promiscuous mode [ 14.532247] e1000e 0000:01:00.0 enx002590aee8ac: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 14.532818] xenbr0: port 1(enx002590aee8ac) entered blocking state [ 14.532929] xenbr0: port 1(enx002590aee8ac) entered forwarding state