[ 0.000000] Linux version 6.10.0-rc4+ (osstest@himrod1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Thu Jun 20 04:16:49 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/godello0--vg-root ro console=hvc0 [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009efff] usable [ 0.000000] Xen: [mem 0x000000000009f000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020060fff] usable [ 0.000000] Xen: [mem 0x000000009573f000-0x0000000095bbefff] reserved [ 0.000000] Xen: [mem 0x0000000095bbf000-0x0000000095fbefff] ACPI NVS [ 0.000000] Xen: [mem 0x0000000095fbf000-0x0000000095ffefff] ACPI data [ 0.000000] Xen: [mem 0x0000000096000000-0x000000009fffffff] reserved [ 0.000000] Xen: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved [ 0.000000] Xen: [mem 0x00000000feb00000-0x00000000feb03fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fed10000-0x00000000fed19fff] reserved [ 0.000000] Xen: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] Xen: [mem 0x00000000fed90000-0x00000000fed90fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: Dell Inc. PowerEdge R220/081N4V, BIOS 1.1.4 05/06/2014 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000022] Xen PV: Detected 4 vCPUS [ 0.000487] tsc: Detected 3092.838 MHz processor [ 0.000812] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000817] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000824] last_pfn = 0x20061 max_arch_pfn = 0x400000000 [ 0.000828] MTRR map: 4 entries (0 fixed + 4 variable; max 20), built from 10 variable MTRRs [ 0.000830] MTRRs set to read-only [ 0.000834] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.000888] Kernel/User page tables isolation: disabled on XEN PV. [ 0.020170] RAMDISK: [mem 0x04000000-0x053a4fff] [ 0.020185] ACPI: Early table checksum verification disabled [ 0.021774] ACPI: RSDP 0x00000000000FE020 000024 (v02 DELL ) [ 0.021787] ACPI: XSDT 0x0000000095FCF188 0000E4 (v01 DELL PE_SC3 00000001 01000013) [ 0.021853] ACPI: FACP 0x0000000095FF7000 00010C (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.021927] ACPI: DSDT 0x0000000095FDF000 012335 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.021944] ACPI: FACS 0x0000000095FBD000 000040 [ 0.021958] ACPI: UEFI 0x0000000095FFD000 000236 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021972] ACPI: UEFI 0x0000000095FFC000 000042 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.021984] ACPI: ASF! 0x0000000095FFB000 0000A5 (v32 DELL PE_SC3 00000001 DELL 00040000) [ 0.021996] ACPI: ASPT 0x0000000095FFA000 000034 (v07 DELL PE_SC3 00000001 DELL 00040000) [ 0.022008] ACPI: BOOT 0x0000000095FF9000 000028 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022022] ACPI: DBGP 0x0000000095FF8000 000034 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022036] ACPI: HPET 0x0000000095FF6000 000038 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022050] ACPI: APIC 0x0000000095FF5000 000092 (v03 DELL PE_SC3 00000001 DELL 00040000) [ 0.022065] ACPI: MCFG 0x0000000095FF4000 00003C (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022079] ACPI: SLIC 0x0000000095FF3000 000176 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022092] ACPI: SSDT 0x0000000095FDC000 002028 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.022107] ACPI: SPMI 0x0000000095FDA000 000040 (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.022121] ACPI: SSDT 0x0000000095FD9000 000533 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022134] ACPI: SSDT 0x0000000095FD8000 000ACE (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022149] ACPI: SSDT 0x0000000095FD4000 003492 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022164] ACPI: SPCR 0x0000000095FF2000 000050 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022177] ACPI: RMAD 0x0000000095FD3000 000080 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022191] ACPI: SSDT 0x0000000095FD2000 000514 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.022205] ACPI: FPDT 0x0000000095FD1000 000044 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022218] ACPI: HEST 0x0000000095FD0000 0000A8 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022232] ACPI: ERST 0x0000000095FCE000 000230 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022247] ACPI: BERT 0x0000000095FCD000 000030 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022259] ACPI: EINJ 0x0000000095FCC000 000150 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022267] ACPI: Reserving FACP table memory at [mem 0x95ff7000-0x95ff710b] [ 0.022268] ACPI: Reserving DSDT table memory at [mem 0x95fdf000-0x95ff1334] [ 0.022269] ACPI: Reserving FACS table memory at [mem 0x95fbd000-0x95fbd03f] [ 0.022270] ACPI: Reserving UEFI table memory at [mem 0x95ffd000-0x95ffd235] [ 0.022271] ACPI: Reserving UEFI table memory at [mem 0x95ffc000-0x95ffc041] [ 0.022271] ACPI: Reserving ASF! table memory at [mem 0x95ffb000-0x95ffb0a4] [ 0.022272] ACPI: Reserving ASPT table memory at [mem 0x95ffa000-0x95ffa033] [ 0.022273] ACPI: Reserving BOOT table memory at [mem 0x95ff9000-0x95ff9027] [ 0.022274] ACPI: Reserving DBGP table memory at [mem 0x95ff8000-0x95ff8033] [ 0.022274] ACPI: Reserving HPET table memory at [mem 0x95ff6000-0x95ff6037] [ 0.022275] ACPI: Reserving APIC table memory at [mem 0x95ff5000-0x95ff5091] [ 0.022276] ACPI: Reserving MCFG table memory at [mem 0x95ff4000-0x95ff403b] [ 0.022276] ACPI: Reserving SLIC table memory at [mem 0x95ff3000-0x95ff3175] [ 0.022277] ACPI: Reserving SSDT table memory at [mem 0x95fdc000-0x95fde027] [ 0.022278] ACPI: Reserving SPMI table memory at [mem 0x95fda000-0x95fda03f] [ 0.022278] ACPI: Reserving SSDT table memory at [mem 0x95fd9000-0x95fd9532] [ 0.022279] ACPI: Reserving SSDT table memory at [mem 0x95fd8000-0x95fd8acd] [ 0.022280] ACPI: Reserving SSDT table memory at [mem 0x95fd4000-0x95fd7491] [ 0.022281] ACPI: Reserving SPCR table memory at [mem 0x95ff2000-0x95ff204f] [ 0.022282] ACPI: Reserving RMAD table memory at [mem 0x95fd3000-0x95fd307f] [ 0.022282] ACPI: Reserving SSDT table memory at [mem 0x95fd2000-0x95fd2513] [ 0.022283] ACPI: Reserving FPDT table memory at [mem 0x95fd1000-0x95fd1043] [ 0.022284] ACPI: Reserving HEST table memory at [mem 0x95fd0000-0x95fd00a7] [ 0.022285] ACPI: Reserving ERST table memory at [mem 0x95fce000-0x95fce22f] [ 0.022285] ACPI: Reserving BERT table memory at [mem 0x95fcd000-0x95fcd02f] [ 0.022286] ACPI: Reserving EINJ table memory at [mem 0x95fcc000-0x95fcc14f] [ 0.022420] APIC: Switched APIC routing to: Xen PV [ 0.025566] Zone ranges: [ 0.025569] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.025572] DMA32 [mem 0x0000000001000000-0x0000000020060fff] [ 0.025573] Normal empty [ 0.025575] Movable zone start for each node [ 0.025576] Early memory node ranges [ 0.025576] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.025579] node 0: [mem 0x0000000000100000-0x0000000020060fff] [ 0.025581] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020060fff] [ 0.025590] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.025669] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.028963] On node 0, zone DMA32: 32671 pages in unavailable ranges [ 0.028968] p2m virtual area at (____ptrval____), size is 40000000 [ 0.121552] Remapped 97 page(s) [ 0.122286] ACPI: PM-Timer IO Port: 0x1808 [ 0.122363] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.122403] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.122419] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.122425] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.122452] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.122458] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.122468] ACPI: SPCR: SPCR table version 1 [ 0.122472] ACPI: SPCR: console: uart,io,0x3f8,115200 [ 0.122476] CPU topo: 8 possible CPUs exceed the limit of 4 [ 0.122486] CPU topo: Max. logical packages: 1 [ 0.122487] CPU topo: Max. logical dies: 1 [ 0.122488] CPU topo: Max. dies per package: 1 [ 0.122495] CPU topo: Max. threads per core: 1 [ 0.122496] CPU topo: Num. cores per package: 4 [ 0.122497] CPU topo: Num. threads per package: 4 [ 0.122497] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.122515] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.122517] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] [ 0.122519] [mem 0x20061000-0x9573efff] available for PCI devices [ 0.122532] Booting kernel on Xen [ 0.122533] Xen version: 4.19-unstable (preserve-AD) [ 0.122538] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.128549] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.129450] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.129457] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.129460] pcpu-alloc: [0] 0 1 2 3 [ 0.129530] xen: PV spinlocks enabled [ 0.129537] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.129541] Kernel command line: placeholder root=/dev/mapper/godello0--vg-root ro console=hvc0 [ 0.129612] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.129636] random: crng init done [ 0.129800] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.129884] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.130488] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.130494] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.130499] software IO TLB: area num 4. [ 0.215641] Memory: 386520K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137512K reserved, 0K cma-reserved) [ 0.215773] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.218272] Dynamic Preempt: voluntary [ 0.218402] rcu: Preemptible hierarchical RCU implementation. [ 0.218402] rcu: RCU event tracing is enabled. [ 0.218404] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.218405] Trampoline variant of Tasks RCU enabled. [ 0.218406] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.218407] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.218426] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.226968] NR_IRQS: 4352, nr_irqs: 456, preallocated irqs: 16 [ 0.227120] xen:events: Using FIFO-based ABI [ 0.227159] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.227166] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.227172] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.227177] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.227183] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.227188] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.227196] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.227201] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.227207] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.227212] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.227218] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.227224] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.227229] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.227235] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.227241] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.227252] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.236486] Console: colour VGA+ 80x25 [ 0.236491] printk: legacy console [tty0] enabled [ 0.257150] printk: legacy console [hvc0] enabled [ 0.258297] ACPI: Core revision 20240322 [ 0.277832] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.278038] Xen: using vcpuop timer interface [ 0.278049] installing Xen timer for CPU 0 [ 0.278250] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2c94d9afcf4, max_idle_ns: 440795231738 ns [ 0.278437] Calibrating delay loop (skipped), value calculated using timer frequency.. 6185.67 BogoMIPS (lpj=3092838) [ 0.278772] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024 [ 0.278916] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4 [ 0.279458] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.279638] Spectre V2 : Mitigation: Retpolines [ 0.279776] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.279950] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.280095] Spectre V2 : Enabling Restricted Speculation for firmware calls [ 0.280242] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.280418] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.280441] MDS: Mitigation: Clear CPU buffers [ 0.280580] MMIO Stale Data: Unknown: No mitigations [ 0.280719] SRBDS: Unknown: Dependent on hypervisor status [ 0.280878] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.281054] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.281197] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.281337] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.281438] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.304165] Freeing SMP alternatives memory: 40K [ 0.304337] pid_max: default: 32768 minimum: 301 [ 0.304469] LSM: initializing lsm=capability,selinux [ 0.304613] SELinux: Initializing. [ 0.304787] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.304968] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.305528] cpu 0 spinlock event irq 25 [ 0.305673] VPMU disabled by hypervisor. [ 0.306206] Performance Events: unsupported p6 CPU model 60 no PMU driver, software events only. [ 0.306389] signal: max sigframe size: 1776 [ 0.306499] rcu: Hierarchical SRCU implementation. [ 0.306639] rcu: Max phase no-delay instances is 400. [ 0.307186] smp: Bringing up secondary CPUs ... [ 0.307526] installing Xen timer for CPU 1 [ 0.307949] installing Xen timer for CPU 2 [ 0.308336] installing Xen timer for CPU 3 [ 0.052178] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0002 [ 0.308520] cpu 1 spinlock event irq 45 [ 0.052178] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0004 [ 0.308812] cpu 2 spinlock event irq 46 [ 0.052178] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0006 [ 0.309487] cpu 3 spinlock event irq 47 [ 0.310487] smp: Brought up 1 node, 4 CPUs [ 0.310809] devtmpfs: initialized [ 0.310809] x86/mm: Memory block size: 128MB [ 0.311558] ACPI: PM: Registering ACPI NVS region [mem 0x95bbf000-0x95fbefff] (4194304 bytes) [ 0.311729] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.311911] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.312180] PM: RTC time: 04:34:07, date: 2024-06-20 [ 0.312555] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.312728] xen:grant_table: Grant tables using version 1 layout [ 0.312918] Grant table initialized [ 0.313202] audit: initializing netlink subsys (disabled) [ 0.313381] audit: type=2000 audit(1718858048.008:1): state=initialized audit_enabled=0 res=1 [ 0.313533] thermal_sys: Registered thermal governor 'step_wise' [ 0.313533] thermal_sys: Registered thermal governor 'user_space' [ 0.313664] Simple Boot Flag at 0x44 set to 0x1 [ 0.313965] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.314490] PCI: ECAM [mem 0xf0000000-0xf7ffffff] (base 0xf0000000) for domain 0000 [bus 00-7f] [ 0.314767] PCI: ECAM [mem 0xf0000000-0xf7ffffff] reserved as E820 entry [ 0.362640] PCI: Using configuration type 1 for base access [ 0.362954] PCI: Dell System detected, enabling pci=bfsort. [ 0.363356] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.363641] ACPI: Added _OSI(Module Device) [ 0.363641] ACPI: Added _OSI(Processor Device) [ 0.363771] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.364440] ACPI: Added _OSI(Processor Aggregator Device) [ 0.375151] ACPI: 6 ACPI AML tables successfully acquired and loaded [ 0.375932] xen: registering gsi 9 triggering 0 polarity 0 [ 0.376548] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.379785] ACPI: Dynamic OEM Table Load: [ 0.379930] ACPI: SSDT 0xFFFF88800399E000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120816) [ 0.380807] ACPI: Dynamic OEM Table Load: [ 0.380943] ACPI: SSDT 0xFFFF888003ADC800 0005AA (v01 PmRef ApIst 00003000 INTL 20120816) [ 0.381758] ACPI: Dynamic OEM Table Load: [ 0.381899] ACPI: SSDT 0xFFFF888003981200 000119 (v01 PmRef ApCst 00003000 INTL 20120816) [ 0.382974] ACPI: _OSC evaluated successfully for all CPUs [ 0.383271] ACPI: Interpreter enabled [ 0.383423] ACPI: PM: (supports S0 S4 S5) [ 0.383438] ACPI: Using IOAPIC for interrupt routing [ 0.383602] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.383788] PCI: Using E820 reservations for host bridge windows [ 0.384171] ACPI: Enabled 11 GPEs in block 00 to 3F [ 0.391903] acpi ABCD0000:00: ACPI dock station (docks/bays count: 1) [ 0.399884] ACPI: \_TZ_.FN00: New power resource [ 0.400065] ACPI: \_TZ_.FN01: New power resource [ 0.400238] ACPI: \_TZ_.FN02: New power resource [ 0.400412] ACPI: \_TZ_.FN03: New power resource [ 0.400476] ACPI: \_TZ_.FN04: New power resource [ 0.401330] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e]) [ 0.401441] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.402407] acpi PNP0A08:00: _OSC: OS now controls [PME PCIeCapability LTR] [ 0.402438] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration [ 0.403094] PCI host bridge to bus 0000:00 [ 0.403231] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.403382] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.403438] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.403610] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xfeafffff window] [ 0.403782] pci_bus 0000:00: root bus resource [bus 00-7e] [ 0.403962] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000 conventional PCI endpoint [ 0.404555] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330 conventional PCI endpoint [ 0.404798] pci 0000:00:14.0: BAR 0 [mem 0xa2b00000-0xa2b0ffff 64bit] [ 0.405229] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 0.405604] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320 conventional PCI endpoint [ 0.405836] pci 0000:00:1a.0: BAR 0 [mem 0xa2b12000-0xa2b123ff] [ 0.406301] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 0.406631] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400 PCIe Root Port [ 0.406921] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.407121] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.407524] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.407738] pci 0000:00:1c.0: Enabling MPC IRBNCE [ 0.407884] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled [ 0.408382] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400 PCIe Root Port [ 0.408565] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.408727] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.408909] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.409316] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.409520] pci 0000:00:1c.2: Enabling MPC IRBNCE [ 0.409663] pci 0000:00:1c.2: Intel PCH root port ACS workaround enabled [ 0.410157] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320 conventional PCI endpoint [ 0.410390] pci 0000:00:1d.0: BAR 0 [mem 0xa2b11000-0xa2b113ff] [ 0.410768] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 0.411102] pci 0000:00:1f.0: [8086:8c52] type 00 class 0x060100 conventional PCI endpoint [ 0.411807] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601 conventional PCI endpoint [ 0.412038] pci 0000:00:1f.2: BAR 0 [io 0x3048-0x304f] [ 0.412210] pci 0000:00:1f.2: BAR 1 [io 0x3054-0x3057] [ 0.412379] pci 0000:00:1f.2: BAR 2 [io 0x3040-0x3047] [ 0.412473] pci 0000:00:1f.2: BAR 3 [io 0x3050-0x3053] [ 0.412643] pci 0000:00:1f.2: BAR 4 [io 0x3020-0x303f] [ 0.412884] pci 0000:00:1f.2: BAR 5 [mem 0xa2b10000-0xa2b107ff] [ 0.413196] pci 0000:00:1f.2: PME# supported from D3hot [ 0.413498] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500 conventional PCI endpoint [ 0.413747] pci 0000:00:1f.3: BAR 0 [mem 0xa2b13000-0xa2b130ff 64bit] [ 0.413979] pci 0000:00:1f.3: BAR 4 [io 0x3000-0x301f] [ 0.414583] pci 0000:01:00.0: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.414914] pci 0000:01:00.0: BAR 0 [mem 0xa2a30000-0xa2a3ffff 64bit pref] [ 0.415179] pci 0000:01:00.0: BAR 2 [mem 0xa2a40000-0xa2a4ffff 64bit pref] [ 0.415498] pci 0000:01:00.0: BAR 4 [mem 0xa2a50000-0xa2a5ffff 64bit pref] [ 0.415737] pci 0000:01:00.0: ROM [mem 0x00000000-0x0003ffff pref] [ 0.416308] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.417123] pci 0000:01:00.1: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.417501] pci 0000:01:00.1: BAR 0 [mem 0xa2a00000-0xa2a0ffff 64bit pref] [ 0.417768] pci 0000:01:00.1: BAR 2 [mem 0xa2a10000-0xa2a1ffff 64bit pref] [ 0.418029] pci 0000:01:00.1: BAR 4 [mem 0xa2a20000-0xa2a2ffff 64bit pref] [ 0.418263] pci 0000:01:00.1: ROM [mem 0x00000000-0x0003ffff pref] [ 0.418907] pci 0000:01:00.1: PME# supported from D0 D3hot D3cold [ 0.419687] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.421059] pci 0000:02:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Upstream Port [ 0.422352] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.422668] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.423123] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.425007] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.426583] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.428103] pci 0000:03:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.429473] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.429868] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.430364] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.432396] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold [ 0.434255] pci 0000:03:01.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.435662] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.436062] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.438689] pci 0000:03:01.0: PME# supported from D0 D3hot D3cold [ 0.442104] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.443924] pci 0000:04:00.0: [1912:0012] type 01 class 0x060400 PCIe to PCI/PCI-X bridge [ 0.445303] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.445698] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.446218] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.449556] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.451133] pci_bus 0000:05: extended config space not accessible [ 0.451518] pci 0000:05:00.0: [102b:0534] type 00 class 0x030000 conventional PCI endpoint [ 0.452179] pci 0000:05:00.0: BAR 0 [mem 0xa1000000-0xa1ffffff pref] [ 0.452553] pci 0000:05:00.0: BAR 1 [mem 0xa2800000-0xa2803fff] [ 0.452966] pci 0000:05:00.0: BAR 2 [mem 0xa2000000-0xa27fffff] [ 0.454437] pci 0000:05:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.457904] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.460158] pci 0000:06:00.0: [1912:0011] type 00 class 0x050000 conventional PCI endpoint [ 0.460825] pci 0000:06:00.0: BAR 0 [mem 0xa2901000-0xa2901fff] [ 0.461235] pci 0000:06:00.0: BAR 1 [mem 0xa2900000-0xa290007f] [ 0.463629] pci 0000:06:00.0: PME# supported from D3hot [ 0.464640] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.466375] pci_bus 0000:00: on NUMA node 0 [ 0.466585] xen: registering gsi 13 triggering 1 polarity 0 [ 0.467588] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.467797] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.468009] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.468219] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.468420] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.468438] ACPI: PCI: Interrupt link LNKE disabled [ 0.468649] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.468792] ACPI: PCI: Interrupt link LNKF disabled [ 0.469002] ACPI: PCI: Interrupt link LNKG configured for IRQ 0 [ 0.469139] ACPI: PCI: Interrupt link LNKG disabled [ 0.469350] ACPI: PCI: Interrupt link LNKH configured for IRQ 11 [ 0.469953] xen:balloon: Initialising balloon driver [ 0.470107] iommu: Default domain type: Translated [ 0.470107] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.470492] SCSI subsystem initialized [ 0.470639] libata version 3.00 loaded. [ 0.470639] ACPI: bus type USB registered [ 0.470639] usbcore: registered new interface driver usbfs [ 0.470761] usbcore: registered new interface driver hub [ 0.470910] usbcore: registered new device driver usb [ 0.471062] pps_core: LinuxPPS API ver. 1 registered [ 0.471441] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.471621] PTP clock support registered [ 0.471785] Advanced Linux Sound Architecture Driver Initialized. [ 0.471785] NetLabel: Initializing [ 0.471904] NetLabel: domain hash size = 128 [ 0.472440] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.472594] NetLabel: unlabeled traffic allowed by default [ 0.472768] PCI: Using ACPI for IRQ routing [ 0.490133] PCI: pci_cache_line_size set to 64 bytes [ 0.490779] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] [ 0.490781] e820: reserve RAM buffer [mem 0x20061000-0x23ffffff] [ 0.490802] pci 0000:05:00.0: vgaarb: setting as boot VGA device [ 0.490802] pci 0000:05:00.0: vgaarb: bridge control possible [ 0.490898] pci 0000:05:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.491438] vgaarb: loaded [ 0.491651] clocksource: Switched to clocksource tsc-early [ 0.491849] VFS: Disk quotas dquot_6.6.0 [ 0.491988] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.492154] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.492332] pnp: PnP ACPI init [ 0.492372] system 00:00: [io 0x0680-0x069f] has been reserved [ 0.492518] system 00:00: [io 0xffff] has been reserved [ 0.492659] system 00:00: [io 0xffff] has been reserved [ 0.492798] system 00:00: [io 0xffff] has been reserved [ 0.492938] system 00:00: [io 0x1800-0x18fe] has been reserved [ 0.493081] system 00:00: [io 0x164e-0x164f] has been reserved [ 0.493256] system 00:01: [io 0x0800-0x087f] has been reserved [ 0.493256] xen: registering gsi 8 triggering 1 polarity 0 [ 0.493495] system 00:03: [io 0x1854-0x1857] has been reserved [ 0.493920] xen: registering gsi 3 triggering 1 polarity 0 [ 0.494151] xen: registering gsi 4 triggering 1 polarity 0 [ 0.494154] Already setup the GSI :4 [ 0.494460] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.494606] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved [ 0.494750] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.494892] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.495036] system 00:06: [mem 0xf0000000-0xf7ffffff] has been reserved [ 0.495179] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved [ 0.495319] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved [ 0.495470] system 00:06: [mem 0xff000000-0xffffffff] could not be reserved [ 0.495617] system 00:06: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.495758] system 00:06: [mem 0xa0000000-0xa0000fff] has been reserved [ 0.495900] system 00:06: [mem 0xa0020000-0xa002ffff] has been reserved [ 0.496859] pnp: PnP ACPI: found 7 devices [ 0.518572] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.518735] NET: Registered PF_INET protocol family [ 0.518904] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.519229] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.519407] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.519607] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.519801] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.519993] TCP: Hash tables configured (established 4096 bind 4096) [ 0.520146] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.520291] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.520472] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.520786] RPC: Registered named UNIX socket transport module. [ 0.520931] RPC: Registered udp transport module. [ 0.521068] RPC: Registered tcp transport module. [ 0.521205] RPC: Registered tcp-with-tls transport module. [ 0.521345] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.521793] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff]: assigned [ 0.521972] pci 0000:01:00.0: ROM [mem 0xa0100000-0xa013ffff pref]: assigned [ 0.522119] pci 0000:01:00.1: ROM [mem 0xa0140000-0xa017ffff pref]: assigned [ 0.522260] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.522416] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff] [ 0.522617] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.522805] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.523087] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.523327] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.523719] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.524000] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.524240] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.524619] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.524894] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.525395] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.525681] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.525914] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.526335] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.526502] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.526658] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.526848] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.526992] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.527130] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.527271] pci_bus 0000:00: resource 7 [mem 0xa0000000-0xfeafffff window] [ 0.527416] pci_bus 0000:01: resource 1 [mem 0xa0100000-0xa01fffff] [ 0.527565] pci_bus 0000:01: resource 2 [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.527738] pci_bus 0000:02: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.527881] pci_bus 0000:02: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.528053] pci_bus 0000:03: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.528199] pci_bus 0000:03: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.528370] pci_bus 0000:04: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.528510] pci_bus 0000:04: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.528682] pci_bus 0000:05: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.528825] pci_bus 0000:05: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.528998] pci_bus 0000:06: resource 1 [mem 0xa2900000-0xa29fffff] [ 0.529265] xen: registering gsi 16 triggering 0 polarity 1 [ 0.529285] xen: --> pirq=16 -> irq=16 (gsi=16) [ 0.530718] xen: registering gsi 16 triggering 0 polarity 1 [ 0.530722] Already setup the GSI :16 [ 0.542561] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x7c0 took 11611 usecs [ 0.542804] xen: registering gsi 23 triggering 0 polarity 1 [ 0.542826] xen: --> pirq=23 -> irq=23 (gsi=23) [ 0.554564] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x7c0 took 11530 usecs [ 0.555056] PCI: CLS 64 bytes, default 64 [ 0.555226] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.555273] Unpacking initramfs... [ 0.555370] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 0.557751] kvm_intel: VMX not supported by CPU 0 [ 0.557895] kvm_amd: CPU 0 isn't AMD or Hygon [ 0.558034] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c94d9afcf4, max_idle_ns: 440795231738 ns [ 0.559338] clocksource: Switched to clocksource tsc [ 0.562430] Initialise system trusted keyrings [ 0.562646] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 0.562938] NFS: Registering the id_resolver key type [ 0.563083] Key type id_resolver registered [ 0.563234] Key type id_legacy registered [ 0.563409] 9p: Installing v9fs 9p2000 file system support [ 0.575757] Key type asymmetric registered [ 0.575909] Asymmetric key parser 'x509' registered [ 0.576072] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.576259] io scheduler mq-deadline registered [ 0.576396] io scheduler kyber registered [ 0.576753] xen: registering gsi 16 triggering 0 polarity 1 [ 0.576761] Already setup the GSI :16 [ 0.577114] pcieport 0000:00:1c.0: PME: Signaling with IRQ 50 [ 0.577513] xen: registering gsi 18 triggering 0 polarity 1 [ 0.577529] xen: --> pirq=18 -> irq=18 (gsi=18) [ 0.577696] pcieport 0000:00:1c.2: PME: Signaling with IRQ 51 [ 0.582058] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.582302] ACPI: button: Power Button [PWRF] [ 0.582810] Monitor-Mwait will be used to enter C-1 state [ 0.582820] Monitor-Mwait will be used to enter C-2 state [ 0.582825] ACPI: \_PR_.CPU0: Found 2 idle states [ 0.583238] ACPI: \_PR_.CPU1: Found 2 idle states [ 0.583608] ACPI: \_PR_.CPU2: Found 2 idle states [ 0.583932] ACPI: \_PR_.CPU3: Found 2 idle states [ 0.584489] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.584634] ACPI: thermal: Thermal Zone [TZ00] (28 C) [ 0.584997] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.585140] ACPI: thermal: Thermal Zone [TZ01] (30 C) [ 0.585512] xen:xen_evtchn: Event-channel device installed [ 0.585724] xen_pciback: backend is vpci [ 0.586291] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.586592] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 0.587308] hpet_acpi_add: no address or irqs in _CRS [ 0.587508] Non-volatile memory driver v1.3 [ 0.588922] loop: module loaded [ 0.592617] ahci 0000:00:1f.2: version 3.0 [ 0.592710] xen: registering gsi 19 triggering 0 polarity 1 [ 0.592735] xen: --> pirq=19 -> irq=19 (gsi=19) [ 0.592905] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled [ 0.593086] ahci 0000:00:1f.2: AHCI vers 0001.0300, 32 command slots, 6 Gbps, SATA mode [ 0.593275] ahci 0000:00:1f.2: 3/6 ports implemented (port mask 0x31) [ 0.593420] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst [ 0.599695] scsi host0: ahci [ 0.599994] scsi host1: ahci [ 0.600288] scsi host2: ahci [ 0.600595] scsi host3: ahci [ 0.600860] scsi host4: ahci [ 0.601126] scsi host5: ahci [ 0.601304] ata1: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10100 irq 53 lpm-pol 0 [ 0.601481] ata2: DUMMY [ 0.601613] ata3: DUMMY [ 0.601743] ata4: DUMMY [ 0.601869] ata5: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10300 irq 53 lpm-pol 0 [ 0.602048] ata6: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10380 irq 53 lpm-pol 0 [ 0.602456] tun: Universal TUN/TAP device driver, 1.6 [ 0.602794] xen: registering gsi 16 triggering 0 polarity 1 [ 0.602801] Already setup the GSI :16 [ 0.633202] Freeing initrd memory: 20116K [ 0.636094] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:58 [ 0.636293] tg3 0000:01:00.0 eth0: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.636522] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.636697] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.637306] xen: registering gsi 17 triggering 0 polarity 1 [ 0.637331] xen: --> pirq=17 -> irq=17 (gsi=17) [ 0.687911] tg3 0000:01:00.1 eth1: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:5a [ 0.688098] tg3 0000:01:00.1 eth1: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.688287] tg3 0000:01:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.688462] tg3 0000:01:00.1 eth1: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.688894] e100: Intel(R) PRO/100 Network Driver [ 0.689033] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.689197] sky2: driver version 1.30 [ 0.689358] xen_netfront: Initialising Xen virtual ethernet driver [ 0.689774] xen: registering gsi 16 triggering 0 polarity 1 [ 0.689780] Already setup the GSI :16 [ 0.689787] xen: registering gsi 16 triggering 0 polarity 1 [ 0.689824] xen: registering gsi 23 triggering 0 polarity 1 [ 0.689829] Already setup the GSI :23 [ 0.689893] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 0.689971] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.690052] Already setup the GSI :16 [ 0.690090] ehci-pci 0000:00:1d.0: debug port 2 [ 0.694643] ehci-pci 0000:00:1d.0: irq 23, io mem 0xa2b11000 [ 0.701203] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 0.701419] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.701597] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.701768] usb usb1: Product: EHCI Host Controller [ 0.701906] usb usb1: Manufacturer: Linux 6.10.0-rc4+ ehci_hcd [ 0.702044] usb usb1: SerialNumber: 0000:00:1d.0 [ 0.702348] hub 1-0:1.0: USB hub found [ 0.702497] hub 1-0:1.0: 2 ports detected [ 0.702822] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 0.703041] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 2 [ 0.703266] ehci-pci 0000:00:1a.0: debug port 2 [ 0.707391] ehci-pci 0000:00:1a.0: irq 16, io mem 0xa2b12000 [ 0.714246] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 0.714459] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.714628] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.714801] usb usb2: Product: EHCI Host Controller [ 0.714939] usb usb2: Manufacturer: Linux 6.10.0-rc4+ ehci_hcd [ 0.715082] usb usb2: SerialNumber: 0000:00:1a.0 [ 0.715380] hub 2-0:1.0: USB hub found [ 0.715535] hub 2-0:1.0: 2 ports detected [ 0.715853] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.716086] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 0.717363] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810 [ 0.717807] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.718017] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 0.718202] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [ 0.718568] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.718785] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.718958] usb usb3: Product: xHCI Host Controller [ 0.719098] usb usb3: Manufacturer: Linux 6.10.0-rc4+ xhci-hcd [ 0.719253] usb usb3: SerialNumber: 0000:00:14.0 [ 0.719563] hub 3-0:1.0: USB hub found [ 0.719730] hub 3-0:1.0: 10 ports detected [ 0.723291] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.10 [ 0.723471] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.723643] usb usb4: Product: xHCI Host Controller [ 0.723782] usb usb4: Manufacturer: Linux 6.10.0-rc4+ xhci-hcd [ 0.723925] usb usb4: SerialNumber: 0000:00:14.0 [ 0.724177] hub 4-0:1.0: USB hub found [ 0.724343] hub 4-0:1.0: 2 ports detected [ 0.724892] usbcore: registered new interface driver usblp [ 0.725046] usbcore: registered new interface driver usb-storage [ 0.725223] i8042: PNP: No PS/2 controller found. [ 0.725471] rtc_cmos 00:02: RTC can wake from S4 [ 0.726068] rtc_cmos 00:02: registered as rtc0 [ 0.726259] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram [ 0.726438] device-mapper: uevent: version 1.0.3 [ 0.726503] xen: registering gsi 18 triggering 0 polarity 1 [ 0.726578] Already setup the GSI :18 [ 0.726647] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 0.726807] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 0.726895] intel_pstate: CPU model not supported [ 0.727174] hid: raw HID events driver (C) Jiri Kosina [ 0.727415] usbcore: registered new interface driver usbhid [ 0.727554] usbhid: USB HID core driver [ 0.727952] Initializing XFRM netlink socket [ 0.728123] NET: Registered PF_INET6 protocol family [ 0.728557] Segment Routing with IPv6 [ 0.728700] In-situ OAM (IOAM) with IPv6 [ 0.728858] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.729091] NET: Registered PF_PACKET protocol family [ 0.729262] 9pnet: Installing 9P2000 support [ 0.729411] Key type dns_resolver registered [ 0.731856] IPI shorthand broadcast: enabled [ 0.732212] i2c i2c-0: Successfully instantiated SPD at 0x51 [ 0.734012] sched_clock: Marking stable (682004367, 51178939)->(742573676, -9390370) [ 0.734479] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.734750] registered taskstats version 1 [ 0.734887] Loading compiled-in X.509 certificates [ 0.736017] PM: Magic number: 12:952:565 [ 0.736229] printk: legacy console [netcon0] enabled [ 0.736369] netconsole: network logging started [ 0.736709] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 0.745248] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 0.745553] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 0.747889] ALSA device list: [ 0.748025] No soundcards found. [ 0.748588] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 0.908241] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.944228] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 0.952230] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 0.953567] ata1.00: ATA-8: TOSHIBA MG03ACA100, FL1D, max UDMA/100 [ 0.954427] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.955911] ata1.00: configured for UDMA/100 [ 0.956209] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MG03ACA1 FL1D PQ: 0 ANSI: 5 [ 0.956938] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 0.956979] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 0.957267] sd 0:0:0:0: [sda] Write Protect is off [ 0.957397] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 0.957416] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.957621] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 0.961225] usb 3-9: new high-speed USB device number 2 using xhci_hcd [ 1.072781] usb 1-1: New USB device found, idVendor=8087, idProduct=8000, bcdDevice= 0.05 [ 1.072952] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.073402] hub 1-1:1.0: USB hub found [ 1.073610] hub 1-1:1.0: 6 ports detected [ 1.080576] usb 2-1: New USB device found, idVendor=8087, idProduct=8008, bcdDevice= 0.05 [ 1.080749] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.081109] hub 2-1:1.0: USB hub found [ 1.081331] hub 2-1:1.0: 4 ports detected [ 1.088230] usb 3-9: New USB device found, idVendor=0624, idProduct=0248, bcdDevice= 0.00 [ 1.088402] usb 3-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.088539] usb 3-9: Product: Gadget USB HUB [ 1.088665] usb 3-9: Manufacturer: no manufacturer [ 1.088797] usb 3-9: SerialNumber: 0123456789 [ 1.089753] hub 3-9:1.0: USB hub found [ 1.089988] hub 3-9:1.0: 6 ports detected [ 1.143445] sda: sda1 sda2 < sda5 > [ 1.143904] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.268353] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.271230] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GTA0N, A3B0, max UDMA/100 [ 1.275948] ata5.00: configured for UDMA/100 [ 1.281076] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW GTA0N A3B0 PQ: 0 ANSI: 5 [ 1.299789] sr 4:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.299970] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.308676] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 1.308768] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 1.384277] usb 3-9.1: new high-speed USB device number 3 using xhci_hcd [ 1.471369] usb 3-9.1: New USB device found, idVendor=0624, idProduct=0249, bcdDevice= 0.00 [ 1.471550] usb 3-9.1: New USB device strings: Mfr=4, Product=5, SerialNumber=6 [ 1.471724] usb 3-9.1: Product: Keyboard/Mouse Function [ 1.471863] usb 3-9.1: Manufacturer: Avocent [ 1.472001] usb 3-9.1: SerialNumber: 20120917 [ 1.479004] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.0/0003:0624:0249.0001/input/input1 [ 1.531540] hid-generic 0003:0624:0249.0001: input,hidraw0: USB HID v1.00 Keyboard [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input0 [ 1.532836] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.1/0003:0624:0249.0002/input/input2 [ 1.533200] hid-generic 0003:0624:0249.0002: input,hidraw1: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input1 [ 1.534135] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.2/0003:0624:0249.0003/input/input3 [ 1.534453] hid-generic 0003:0624:0249.0003: input,hidraw2: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input2 [ 1.620422] ata6: SATA link down (SStatus 0 SControl 300) [ 1.621797] Freeing unused kernel image (initmem) memory: 2680K [ 1.621960] Write protecting the kernel read-only data: 24576k [ 1.636201] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 1.837323] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.837510] Run /init as init process [ 1.837651] with arguments: [ 1.837652] /init [ 1.837653] placeholder [ 1.837654] with environment: [ 1.837655] HOME=/ [ 1.837656] TERM=linux [ 2.067133] tg3 0000:01:00.0 enx549f3505fd58: renamed from eth0 [ 2.068941] tg3 0000:01:00.1 enx549f3505fd5a: renamed from eth1 [ 2.742942] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 2.747298] EXT4-fs (dm-0): mounted filesystem a3509b34-5633-459e-ad8e-743ff5bc20ce ro with ordered data mode. Quota mode: none. [ 6.400811] EXT4-fs (dm-0): re-mounted a3509b34-5633-459e-ad8e-743ff5bc20ce r/w. Quota mode: none. [ 7.504913] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 7.518297] EXT4-fs (sda1): mounted filesystem 69424bc6-ea79-4a7b-95aa-de47430cf6bc r/w with ordered data mode. Quota mode: none. [ 7.583699] Adding 1949692k swap on /dev/mapper/godello0--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 9.101283] xenbr0: port 1(enx549f3505fd58) entered blocking state [ 9.101470] xenbr0: port 1(enx549f3505fd58) entered disabled state [ 9.101623] tg3 0000:01:00.0 enx549f3505fd58: entered allmulticast mode [ 9.101801] tg3 0000:01:00.0 enx549f3505fd58: entered promiscuous mode [ 12.754924] tg3 0000:01:00.0 enx549f3505fd58: Link is up at 1000 Mbps, full duplex [ 12.755174] tg3 0000:01:00.0 enx549f3505fd58: Flow control is off for TX and off for RX [ 12.755349] tg3 0000:01:00.0 enx549f3505fd58: EEE is disabled [ 12.755584] xenbr0: port 1(enx549f3505fd58) entered blocking state [ 12.755731] xenbr0: port 1(enx549f3505fd58) entered forwarding state