[ 0.000000] Linux version 6.10.0-rc4+ (osstest@pinot1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Sat Jun 22 14:11:52 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/pinot1--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000099fff] usable [ 0.000000] Xen: [mem 0x000000000009a800-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020065fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000f6000000-0x00000000f6003fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SML/H8SML, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 2/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000011] Xen PV: Detected 4 vCPUS [ 0.039085] tsc: Fast TSC calibration using PIT [ 0.039086] tsc: Detected 2799.903 MHz processor [ 0.039088] tsc: Detected 2800.020 MHz TSC [ 0.039313] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.039317] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.039325] last_pfn = 0x20066 max_arch_pfn = 0x400000000 [ 0.039328] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.039330] MTRRs set to read-only [ 0.039333] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.065360] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.065383] ACPI: Early table checksum verification disabled [ 0.066521] ACPI: RSDP 0x00000000000FA1C0 000024 (v02 ACPIAM) [ 0.066532] ACPI: XSDT 0x00000000DFEA0100 00007C (v01 SMCI 20131125 MSFT 00000097) [ 0.066558] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.066599] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.066611] ACPI: DSDT 0x00000000DFEA0600 00562B (v01 1CF11 1CF11000 00000000 INTL 20051117) [ 0.066622] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.066632] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.066643] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.066653] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.066664] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.066675] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.066686] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.066696] ACPI: SSDT 0x00000000DFEAA6F0 000B9C (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.066707] ACPI: EINJ 0x00000000DFEAB290 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.066717] ACPI: BERT 0x00000000DFEAB420 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.066727] ACPI: ERST 0x00000000DFEAB450 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.066738] ACPI: HEST 0x00000000DFEAB660 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.066743] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.066745] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c2a] [ 0.066747] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.066748] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.066750] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.066751] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.066752] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.066754] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.066755] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.066756] ACPI: Reserving SSDT table memory at [mem 0xdfeaa6f0-0xdfeab28b] [ 0.066757] ACPI: Reserving EINJ table memory at [mem 0xdfeab290-0xdfeab3bf] [ 0.066758] ACPI: Reserving BERT table memory at [mem 0xdfeab420-0xdfeab44f] [ 0.066760] ACPI: Reserving ERST table memory at [mem 0xdfeab450-0xdfeab65f] [ 0.066761] ACPI: Reserving HEST table memory at [mem 0xdfeab660-0xdfeab707] [ 0.066879] APIC: Switched APIC routing to: Xen PV [ 0.069201] Zone ranges: [ 0.069203] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.069206] DMA32 [mem 0x0000000001000000-0x0000000020065fff] [ 0.069208] Normal empty [ 0.069210] Movable zone start for each node [ 0.069211] Early memory node ranges [ 0.069211] node 0: [mem 0x0000000000001000-0x0000000000099fff] [ 0.069214] node 0: [mem 0x0000000000100000-0x0000000020065fff] [ 0.069216] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020065fff] [ 0.069227] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.069363] On node 0, zone DMA: 102 pages in unavailable ranges [ 0.073466] On node 0, zone DMA32: 32666 pages in unavailable ranges [ 0.073478] p2m virtual area at (____ptrval____), size is 40000000 [ 0.293798] Remapped 102 page(s) [ 0.294323] ACPI: PM-Timer IO Port: 0x808 [ 0.294357] CPU topo: CPU limit of 4 reached. Ignoring further CPUs [ 0.294388] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.294392] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.294414] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.294422] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.294435] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.294439] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.294461] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.294465] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.294478] CPU topo: Max. logical packages: 1 [ 0.294479] CPU topo: Max. logical dies: 1 [ 0.294480] CPU topo: Max. dies per package: 1 [ 0.294487] CPU topo: Max. threads per core: 1 [ 0.294488] CPU topo: Num. cores per package: 4 [ 0.294489] CPU topo: Num. threads per package: 4 [ 0.294490] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.294491] CPU topo: Rejected CPUs 4 [ 0.294510] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.294513] PM: hibernation: Registered nosave memory: [mem 0x0009a000-0x0009afff] [ 0.294514] PM: hibernation: Registered nosave memory: [mem 0x0009b000-0x000fffff] [ 0.294517] [mem 0x20066000-0xdfe9dfff] available for PCI devices [ 0.294522] Booting kernel on Xen [ 0.294523] Xen version: 4.19-unstable (preserve-AD) [ 0.294528] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.300967] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.301888] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.301899] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.301904] pcpu-alloc: [0] 0 1 2 3 [ 0.301975] xen: PV spinlocks enabled [ 0.301980] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.301984] Kernel command line: placeholder root=/dev/mapper/pinot1--vg-root ro console=hvc0 [ 0.302061] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.302262] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.302360] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.302570] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.302575] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.302578] software IO TLB: area num 4. [ 0.408725] Memory: 386444K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137588K reserved, 0K cma-reserved) [ 0.408849] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.411640] Dynamic Preempt: voluntary [ 0.411755] rcu: Preemptible hierarchical RCU implementation. [ 0.411756] rcu: RCU event tracing is enabled. [ 0.411757] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.411759] Trampoline variant of Tasks RCU enabled. [ 0.411761] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.411762] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.411781] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.418626] NR_IRQS: 4352, nr_irqs: 1000, preallocated irqs: 16 [ 0.418782] xen:events: Using FIFO-based ABI [ 0.418811] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.418822] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.418828] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.418834] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.418839] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.418844] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.418849] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.418854] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.418859] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.418865] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.418870] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.418875] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.418880] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.418886] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.418891] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.418902] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.424991] Console: colour VGA+ 80x25 [ 0.424996] printk: legacy console [tty0] enabled [ 0.438837] printk: legacy console [hvc0] enabled [ 0.439535] ACPI: Core revision 20240322 [ 0.443522] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.443681] Xen: using vcpuop timer interface [ 0.443687] installing Xen timer for CPU 0 [ 0.443931] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x285c53933e6, max_idle_ns: 440795231913 ns [ 0.444091] Calibrating delay loop (skipped), value calculated using timer frequency.. 5600.04 BogoMIPS (lpj=2800020) [ 0.444284] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.444523] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.444633] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.444775] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.445101] Spectre V2 : Mitigation: Retpolines [ 0.445204] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.445347] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.445457] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.445567] RETBleed: Mitigation: untrained return thunk [ 0.445673] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.445818] Speculative Store Bypass: Vulnerable [ 0.445943] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.446093] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.446227] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.446341] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.446451] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.472008] Freeing SMP alternatives memory: 40K [ 0.472098] pid_max: default: 32768 minimum: 301 [ 0.472280] LSM: initializing lsm=capability,selinux [ 0.472392] SELinux: Initializing. [ 0.472547] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.472692] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.474219] cpu 0 spinlock event irq 57 [ 0.474347] VPMU disabled by hypervisor. [ 0.474849] Performance Events: PMU not available due to virtualization, using software events only. [ 0.475011] signal: max sigframe size: 1776 [ 0.475155] rcu: Hierarchical SRCU implementation. [ 0.475284] rcu: Max phase no-delay instances is 400. [ 0.481257] smp: Bringing up secondary CPUs ... [ 0.481601] installing Xen timer for CPU 1 [ 0.482013] installing Xen timer for CPU 2 [ 0.482363] installing Xen timer for CPU 3 [ 0.026181] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.482617] cpu 1 spinlock event irq 77 [ 0.026181] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.483290] cpu 2 spinlock event irq 78 [ 0.026181] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.484264] cpu 3 spinlock event irq 79 [ 0.485366] smp: Brought up 1 node, 4 CPUs [ 0.486273] devtmpfs: initialized [ 0.486273] x86/mm: Memory block size: 128MB [ 0.487188] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.487364] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.487559] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.487789] PM: RTC time: 15:00:56, date: 2024-06-22 [ 0.488230] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.488372] xen:grant_table: Grant tables using version 1 layout [ 0.488500] Grant table initialized [ 0.488856] audit: initializing netlink subsys (disabled) [ 0.489097] audit: type=2000 audit(1719068457.075:1): state=initialized audit_enabled=0 res=1 [ 0.489244] thermal_sys: Registered thermal governor 'step_wise' [ 0.489244] thermal_sys: Registered thermal governor 'user_space' [ 0.489366] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.490241] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.663306] PCI: Using configuration type 1 for base access [ 0.663599] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.664301] ACPI: Added _OSI(Module Device) [ 0.664517] ACPI: Added _OSI(Processor Device) [ 0.664792] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.665123] ACPI: Added _OSI(Processor Aggregator Device) [ 0.684790] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.688307] xen: registering gsi 9 triggering 0 polarity 1 [ 0.692676] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.694750] ACPI: Interpreter enabled [ 0.695102] ACPI: PM: (supports S0 S1 S4 S5) [ 0.695364] ACPI: Using IOAPIC for interrupt routing [ 0.695920] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.696107] PCI: Using E820 reservations for host bridge windows [ 0.697502] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.729242] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.729378] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.729534] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.729649] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.729819] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.730290] PCI host bridge to bus 0000:00 [ 0.730393] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.730506] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.730659] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.730801] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.730967] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.731093] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.731254] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.731822] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.732389] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.732606] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.732729] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.732844] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.733008] pci 0000:00:09.0: enabling Extended Tags [ 0.733218] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.733578] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.733798] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.733916] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.734031] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.734144] pci 0000:00:0a.0: enabling Extended Tags [ 0.734370] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.734742] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f conventional PCI endpoint [ 0.734932] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.735062] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.735116] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.735245] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.735373] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.735507] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.735689] pci 0000:00:11.0: set SATA to AHCI mode [ 0.736014] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.736136] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.736533] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.736745] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.737153] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.737349] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.737689] pci 0000:00:12.2: supports D1 D2 [ 0.737792] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.738092] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.738282] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.738714] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.738903] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.739332] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.739526] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.739860] pci 0000:00:13.2: supports D1 D2 [ 0.739971] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.740272] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.740811] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.740999] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.741116] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.741245] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.741412] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.741570] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.741731] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.741842] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.741951] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.742062] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.742289] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.742865] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.743099] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.743227] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.743349] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.743640] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.743829] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.744286] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.744648] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.744963] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.745267] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.745663] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.745978] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.746427] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.746621] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.746791] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.746924] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.747294] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.750152] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.750544] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.750782] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.750948] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.751097] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.751547] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.754142] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.754317] pci_bus 0000:03: extended config space not accessible [ 0.754563] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.754817] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.754954] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.755088] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.755339] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.756481] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.756884] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.757115] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.758117] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.758476] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.758812] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.759299] pci_bus 0000:00: on NUMA node 0 [ 0.761544] xen: registering gsi 13 triggering 1 polarity 0 [ 0.763591] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.764144] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.764730] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.765293] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.765889] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.766377] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.766965] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.767174] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.767504] xen:balloon: Initialising balloon driver [ 0.768393] iommu: Default domain type: Translated [ 0.768685] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.769226] SCSI subsystem initialized [ 0.769549] libata version 3.00 loaded. [ 0.769549] ACPI: bus type USB registered [ 0.770216] usbcore: registered new interface driver usbfs [ 0.770537] usbcore: registered new interface driver hub [ 0.770879] usbcore: registered new device driver usb [ 0.771224] pps_core: LinuxPPS API ver. 1 registered [ 0.771500] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.771835] PTP clock support registered [ 0.772313] Advanced Linux Sound Architecture Driver Initialized. [ 0.774688] NetLabel: Initializing [ 0.774907] NetLabel: domain hash size = 128 [ 0.775107] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.775508] NetLabel: unlabeled traffic allowed by default [ 0.775890] PCI: Using ACPI for IRQ routing [ 0.850522] PCI: pci_cache_line_size set to 64 bytes [ 0.850712] e820: reserve RAM buffer [mem 0x0009a000-0x0009ffff] [ 0.850717] e820: reserve RAM buffer [mem 0x20066000-0x23ffffff] [ 0.850786] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.850786] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.850786] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.851093] vgaarb: loaded [ 0.852160] clocksource: Switched to clocksource tsc-early [ 0.852638] VFS: Disk quotas dquot_6.6.0 [ 0.852768] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.852951] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.853068] pnp: PnP ACPI init [ 0.853505] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.853771] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.854284] xen: registering gsi 8 triggering 1 polarity 0 [ 0.854550] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.854885] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.855008] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.855561] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.855680] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.855796] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.855911] system 00:05: [io 0x040b] has been reserved [ 0.856022] system 00:05: [io 0x04d6] has been reserved [ 0.856166] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.856282] system 00:05: [io 0x0c14] has been reserved [ 0.856395] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.856511] system 00:05: [io 0x0c52] has been reserved [ 0.856622] system 00:05: [io 0x0c6c] has been reserved [ 0.856735] system 00:05: [io 0x0c6f] has been reserved [ 0.856884] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.856999] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.857123] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.857239] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.857381] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.857496] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.857611] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.857731] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.857846] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.857962] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.858076] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.858238] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.858357] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.858475] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.858899] xen: registering gsi 4 triggering 1 polarity 0 [ 0.858904] Already setup the GSI :4 [ 0.859009] pnp 00:06: [dma 0 disabled] [ 0.859363] xen: registering gsi 3 triggering 1 polarity 0 [ 0.859374] pnp 00:07: [dma 0 disabled] [ 0.859555] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.860005] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.860213] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.860335] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.860454] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.860573] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.860868] pnp: PnP ACPI: found 10 devices [ 0.884701] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.884890] NET: Registered PF_INET protocol family [ 0.885098] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.885562] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.885719] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.885871] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.886045] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.886254] TCP: Hash tables configured (established 4096 bind 4096) [ 0.886436] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.886560] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.886752] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.888546] RPC: Registered named UNIX socket transport module. [ 0.888672] RPC: Registered udp transport module. [ 0.888789] RPC: Registered tcp transport module. [ 0.888899] RPC: Registered tcp-with-tls transport module. [ 0.889010] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.889960] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.890084] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.890250] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.890403] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.890519] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.890644] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.890783] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.890905] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.891030] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.891210] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.891328] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.891445] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.891604] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.891722] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.891841] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.891954] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.892071] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.892192] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.892309] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.892426] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.892544] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.892660] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.892800] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.892930] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.893049] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.893389] xen: registering gsi 16 triggering 0 polarity 1 [ 0.893435] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.557321] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 648482 usecs [ 1.557555] xen: registering gsi 16 triggering 0 polarity 1 [ 1.557565] Already setup the GSI :16 [ 1.582574] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 24484 usecs [ 1.583229] xen: registering gsi 17 triggering 0 polarity 1 [ 1.583286] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.583471] xen: registering gsi 18 triggering 0 polarity 1 [ 1.583488] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.607312] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23335 usecs [ 1.607573] xen: registering gsi 18 triggering 0 polarity 1 [ 1.607584] Already setup the GSI :18 [ 1.631816] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 23725 usecs [ 1.632264] xen: registering gsi 19 triggering 0 polarity 1 [ 1.632313] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.632515] xen: registering gsi 18 triggering 0 polarity 1 [ 1.632519] Already setup the GSI :18 [ 1.657596] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 24533 usecs [ 1.658205] PCI: CLS 64 bytes, default 64 [ 1.658351] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.658433] Unpacking initramfs... [ 1.658460] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 1.658794] kvm_intel: VMX not supported by CPU 1 [ 1.659027] kvm_amd: SVM not supported by CPU 1 [ 1.659205] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x285c53933e6, max_idle_ns: 440795231913 ns [ 1.659412] clocksource: Switched to clocksource tsc [ 1.665525] Initialise system trusted keyrings [ 1.666118] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.666568] NFS: Registering the id_resolver key type [ 1.666874] Key type id_resolver registered [ 1.667163] Key type id_legacy registered [ 1.667875] 9p: Installing v9fs 9p2000 file system support [ 1.692839] Key type asymmetric registered [ 1.693244] Asymmetric key parser 'x509' registered [ 1.693707] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.694137] io scheduler mq-deadline registered [ 1.694546] io scheduler kyber registered [ 1.695559] xen: registering gsi 53 triggering 0 polarity 1 [ 1.695615] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.695965] xen: registering gsi 54 triggering 0 polarity 1 [ 1.695993] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.696505] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.696743] ACPI: button: Power Button [PWRB] [ 1.696909] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.697139] ACPI: button: Power Button [PWRF] [ 1.699464] ACPI: \_PR_.P001: Found 2 idle states [ 1.699708] ACPI: \_PR_.P002: Found 2 idle states [ 1.699903] ACPI: \_PR_.P003: Found 2 idle states [ 1.700067] ACPI: \_PR_.P004: Found 2 idle states [ 1.701089] xen:xen_evtchn: Event-channel device installed [ 1.701415] xen_pciback: backend is vpci [ 1.702677] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.703113] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.705671] hpet_acpi_add: no address or irqs in _CRS [ 1.705872] Non-volatile memory driver v1.3 [ 1.715356] loop: module loaded [ 1.736203] ahci 0000:00:11.0: version 3.0 [ 1.736370] xen: registering gsi 22 triggering 0 polarity 1 [ 1.736426] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.736630] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.736797] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.736976] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.738799] scsi host0: ahci [ 1.739365] scsi host1: ahci [ 1.739973] scsi host2: ahci [ 1.740387] scsi host3: ahci [ 1.740592] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.740749] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.740901] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.741098] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.741762] tun: Universal TUN/TAP device driver, 1.6 [ 1.742034] e100: Intel(R) PRO/100 Network Driver [ 1.742148] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.742291] sky2: driver version 1.30 [ 1.742504] xen_netfront: Initialising Xen virtual ethernet driver [ 1.742991] xen: registering gsi 16 triggering 0 polarity 1 [ 1.743004] Already setup the GSI :16 [ 1.743212] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.743439] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 1.743563] xen: registering gsi 17 triggering 0 polarity 1 [ 1.743615] Already setup the GSI :17 [ 1.743700] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.744696] xen: registering gsi 19 triggering 0 polarity 1 [ 1.744720] Already setup the GSI :19 [ 1.799483] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.799661] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.799808] usb usb1: Product: OHCI PCI host controller [ 1.799920] usb usb1: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 1.800034] usb usb1: SerialNumber: 0000:00:12.0 [ 1.800661] hub 1-0:1.0: USB hub found [ 1.800785] hub 1-0:1.0: 3 ports detected [ 1.801329] xen: registering gsi 16 triggering 0 polarity 1 [ 1.801339] Already setup the GSI :16 [ 1.802150] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.802431] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 1.802580] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.802748] ehci-pci 0000:00:12.2: debug port 1 [ 1.803008] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.809281] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.810095] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.810371] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.810514] usb usb2: Product: EHCI Host Controller [ 1.810620] usb usb2: Manufacturer: Linux 6.10.0-rc4+ ehci_hcd [ 1.810728] usb usb2: SerialNumber: 0000:00:12.2 [ 1.811092] hub 2-0:1.0: USB hub found [ 1.811234] hub 2-0:1.0: 6 ports detected [ 1.863554] hub 1-0:1.0: USB hub found [ 1.864015] hub 1-0:1.0: 3 ports detected [ 1.865338] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.865668] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 1.865842] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.866023] ehci-pci 0000:00:13.2: debug port 1 [ 1.866298] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.873248] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.873543] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.873741] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.873881] usb usb3: Product: EHCI Host Controller [ 1.873987] usb usb3: Manufacturer: Linux 6.10.0-rc4+ ehci_hcd [ 1.874134] usb usb3: SerialNumber: 0000:00:13.2 [ 1.874514] hub 3-0:1.0: USB hub found [ 1.874654] hub 3-0:1.0: 6 ports detected [ 1.875262] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.875525] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.875770] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.897150] Freeing initrd memory: 20192K [ 1.931733] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.931901] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.932041] usb usb4: Product: OHCI PCI host controller [ 1.932146] usb usb4: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 1.932270] usb usb4: SerialNumber: 0000:00:12.1 [ 1.933030] hub 4-0:1.0: USB hub found [ 1.933643] hub 4-0:1.0: 3 ports detected [ 1.934364] xen: registering gsi 18 triggering 0 polarity 1 [ 1.934375] Already setup the GSI :18 [ 1.934536] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.934818] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.935052] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 1.991509] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.991683] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.991825] usb usb5: Product: OHCI PCI host controller [ 1.991931] usb usb5: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 1.992079] usb usb5: SerialNumber: 0000:00:13.0 [ 1.992508] hub 5-0:1.0: USB hub found [ 1.992669] hub 5-0:1.0: 3 ports detected [ 1.993421] xen: registering gsi 18 triggering 0 polarity 1 [ 1.993432] Already setup the GSI :18 [ 1.993596] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 1.993845] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 1.994046] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 2.049503] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.049692] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.049832] usb usb6: Product: OHCI PCI host controller [ 2.049936] usb usb6: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.050043] usb usb6: SerialNumber: 0000:00:13.1 [ 2.050408] hub 6-0:1.0: USB hub found [ 2.050551] hub 6-0:1.0: 3 ports detected [ 2.051074] xen: registering gsi 18 triggering 0 polarity 1 [ 2.051082] Already setup the GSI :18 [ 2.051186] ata4: SATA link down (SStatus 0 SControl 300) [ 2.051281] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 2.051346] ata3: SATA link down (SStatus 0 SControl 300) [ 2.051491] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 2.051735] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 2.107368] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.107521] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.107661] usb usb7: Product: OHCI PCI host controller [ 2.107767] usb usb7: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.107874] usb usb7: SerialNumber: 0000:00:14.5 [ 2.108156] hub 7-0:1.0: USB hub found [ 2.108318] hub 7-0:1.0: 2 ports detected [ 2.108702] usbcore: registered new interface driver usblp [ 2.108832] usbcore: registered new interface driver usb-storage [ 2.108978] i8042: PNP: No PS/2 controller found. [ 2.109082] i8042: Probing ports directly. [ 2.112343] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.112452] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.112876] rtc_cmos 00:02: RTC can wake from S4 [ 2.113432] rtc_cmos 00:02: registered as rtc0 [ 2.113577] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 2.113731] device-mapper: uevent: version 1.0.3 [ 2.113940] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 2.114130] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 2.114292] hid: raw HID events driver (C) Jiri Kosina [ 2.114621] usbcore: registered new interface driver usbhid [ 2.114727] usbhid: USB HID core driver [ 2.115231] Initializing XFRM netlink socket [ 2.115366] NET: Registered PF_INET6 protocol family [ 2.116063] Segment Routing with IPv6 [ 2.116178] In-situ OAM (IOAM) with IPv6 [ 2.116331] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.116589] NET: Registered PF_PACKET protocol family [ 2.116720] 9pnet: Installing 9P2000 support [ 2.116910] Key type dns_resolver registered [ 2.117025] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 2.117530] IPI shorthand broadcast: enabled [ 2.122108] sched_clock: Marking stable (2096003521, 25181356)->(2137391606, -16206729) [ 2.122632] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.122935] registered taskstats version 1 [ 2.123037] Loading compiled-in X.509 certificates [ 2.125271] PM: Magic number: 12:206:33 [ 2.125456] printk: legacy console [netcon0] enabled [ 2.125561] netconsole: network logging started [ 2.125762] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.136149] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.136594] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.136758] ALSA device list: [ 2.136855] No soundcards found. [ 2.139238] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 2.212247] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.212387] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.213050] ata2.00: ATA-9: WDC WD1003FZEX-00MK2A0, 01.01A01, max UDMA/133 [ 2.213571] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 2.213808] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 2.214359] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 2.214552] ata2.00: configured for UDMA/133 [ 2.216237] ata1.00: configured for UDMA/133 [ 2.216474] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 2.217328] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.217339] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.217607] sd 0:0:0:0: [sda] Write Protect is off [ 2.217722] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.217753] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.217877] scsi 1:0:0:0: Direct-Access ATA WDC WD1003FZEX-0 1A01 PQ: 0 ANSI: 5 [ 2.218083] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 2.218822] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 2.218893] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.219118] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 2.219292] sd 1:0:0:0: [sdb] Write Protect is off [ 2.219433] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.219491] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.219726] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 2.241962] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.256411] sdb: sdb1 sdb2 < sdb5 > [ 2.256769] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.258381] Freeing unused kernel image (initmem) memory: 2680K [ 2.258539] Write protecting the kernel read-only data: 24576k [ 2.270941] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.364251] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.384330] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.384491] Run /init as init process [ 2.384590] with arguments: [ 2.384592] /init [ 2.384593] placeholder [ 2.384594] with environment: [ 2.384596] HOME=/ [ 2.384597] TERM=linux [ 2.530344] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.530516] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.530641] usb 6-2: Product: Hermon USB hidmouse Device [ 2.530756] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.536871] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.537227] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.540776] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.592528] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.654841] e1000e: Intel(R) PRO/1000 Network Driver [ 2.655012] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.656606] xen: registering gsi 48 triggering 0 polarity 1 [ 2.656644] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.656900] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.701150] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.745065] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e9:2a [ 2.745236] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.745427] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.745650] xen: registering gsi 47 triggering 0 polarity 1 [ 2.745677] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.745869] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.793300] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.795241] random: crng init done [ 2.838139] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e9:2b [ 2.838339] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.838531] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.840565] e1000e 0000:01:00.0 enx002590aee92a: renamed from eth0 [ 2.841135] e1000e 0000:02:00.0 enx002590aee92b: renamed from eth1 [ 3.536239] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.548354] EXT4-fs (dm-0): mounted filesystem 021b9819-2f1b-4b09-89ea-52a2bdb1ed1d ro with ordered data mode. Quota mode: none. [ 7.298112] EXT4-fs (dm-0): re-mounted 021b9819-2f1b-4b09-89ea-52a2bdb1ed1d r/w. Quota mode: none. [ 8.120312] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 8.128780] EXT4-fs (sdb1): mounted filesystem df605573-76f2-4c11-b265-e5365c9a3015 r/w with ordered data mode. Quota mode: none. [ 8.205224] Adding 1949692k swap on /dev/mapper/pinot1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 9.715131] xenbr0: port 1(enx002590aee92a) entered blocking state [ 9.715374] xenbr0: port 1(enx002590aee92a) entered disabled state [ 9.715493] e1000e 0000:01:00.0 enx002590aee92a: entered allmulticast mode [ 9.715675] e1000e 0000:01:00.0 enx002590aee92a: entered promiscuous mode [ 12.840261] e1000e 0000:01:00.0 enx002590aee92a: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 12.840804] xenbr0: port 1(enx002590aee92a) entered blocking state [ 12.840915] xenbr0: port 1(enx002590aee92a) entered forwarding state