[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-21-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.90-1 (2024-05-03) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015524K/2097152K available (12288K kernel code, 1714K rwdata, 3748K rodata, 2048K init, 382K bss, 65244K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39974 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002620] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002635] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002650] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002661] Ignoring duplicate/late registration of read_current_timer delay [ 0.003028] Console: colour dummy device 80x30 [ 0.003068] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003083] CPU: Testing write buffer coherency: ok [ 0.003125] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003133] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003141] pid_max: default: 32768 minimum: 301 [ 0.003500] LSM: Security Framework initializing [ 0.003572] landlock: Up and running. [ 0.003577] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003764] AppArmor: AppArmor initialized [ 0.003776] TOMOYO Linux initialized [ 0.003822] LSM support for eBPF active [ 0.004066] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004080] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005487] /cpus/cpu@0 missing clock-frequency property [ 0.005515] /cpus/cpu@1 missing clock-frequency property [ 0.005529] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006489] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006496] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006601] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006606] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006746] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007907] rcu: Hierarchical SRCU implementation. [ 0.007913] rcu: Max phase no-delay instances is 1000. [ 0.010035] EFI services will not be available. [ 0.010381] smp: Bringing up secondary CPUs ... [ 0.011125] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011137] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011269] smp: Brought up 1 node, 2 CPUs [ 0.011278] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011285] CPU: All CPU(s) started in HYP mode. [ 0.011289] CPU: Virtualization extensions available. [ 0.012159] devtmpfs: initialized [ 0.023665] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023908] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023933] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024491] pinctrl core: initialized pinctrl subsystem [ 0.025238] DMI not present or invalid. [ 0.025911] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027477] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.029056] audit: initializing netlink subsys (disabled) [ 0.029262] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030467] thermal_sys: Registered thermal governor 'fair_share' [ 0.030475] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030479] thermal_sys: Registered thermal governor 'step_wise' [ 0.030484] thermal_sys: Registered thermal governor 'user_space' [ 0.030488] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030692] No ATAGs? [ 0.030760] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030769] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031870] Serial: AMBA PL011 UART driver [ 0.085292] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.092575] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.095836] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.095844] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.102744] iommu: Default domain type: Translated [ 0.102752] iommu: DMA domain TLB invalidation policy: strict mode [ 0.103735] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.104270] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.104282] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.104931] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.104961] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.105168] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.105526] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.105536] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.105925] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.106215] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.106225] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.106527] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.106645] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.106654] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.106840] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.107054] pps_core: LinuxPPS API ver. 1 registered [ 0.107059] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.107076] PTP clock support registered [ 0.108599] NetLabel: Initializing [ 0.108606] NetLabel: domain hash size = 128 [ 0.108611] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.108665] NetLabel: unlabeled traffic allowed by default [ 0.108841] vgaarb: loaded [ 0.109426] clocksource: Switched to clocksource mct-frc [ 0.110008] VFS: Disk quotas dquot_6.6.0 [ 0.110091] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.110848] AppArmor: AppArmor Filesystem Enabled [ 0.121060] NET: Registered PF_INET protocol family [ 0.121262] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.122751] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.122854] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.122880] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.122981] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.123212] TCP: Hash tables configured (established 8192 bind 8192) [ 0.123444] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.123537] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123579] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123802] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.123840] NET: Registered PF_XDP protocol family [ 0.123852] PCI: CLS 0 bytes, default 64 [ 0.124364] Trying to unpack rootfs image as initramfs... [ 0.124711] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.130119] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.195583] Initialise system trusted keyrings [ 0.195657] Key type blacklist registered [ 0.196884] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.205132] zbud: loaded [ 0.208749] integrity: Platform Keyring initialized [ 0.208792] integrity: Machine keyring initialized [ 0.208800] Key type asymmetric registered [ 0.208808] Asymmetric key parser 'x509' registered [ 1.431010] Freeing initrd memory: 25116K [ 1.453229] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.453537] bounce: pool size: 64 pages [ 1.453725] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.453925] io scheduler mq-deadline registered [ 1.459061] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.480225] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.480237] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.482678] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.482688] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.483511] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.483520] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.484367] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.484375] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.486749] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.489570] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.492359] Serial: AMBA driver [ 1.492589] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.493077] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.493602] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.574417] printk: console [ttySAC2] enabled [ 2.579238] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.589919] STM32 USART driver initialized [ 2.604352] mousedev: PS/2 mouse device common for all mice [ 2.635596] s5m-rtc s5m-rtc: registered as rtc0 [ 2.644222] s5m-rtc s5m-rtc: setting system clock to 2024-06-22T20:27:07 UTC (1719088027) [ 2.654126] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.661630] ledtrig-cpu: registered to indicate activity on CPUs [ 2.669643] NET: Registered PF_INET6 protocol family [ 2.693901] Segment Routing with IPv6 [ 2.696147] In-situ OAM (IOAM) with IPv6 [ 2.700135] mip6: Mobile IPv6 [ 2.702990] NET: Registered PF_PACKET protocol family [ 2.708152] mpls_gso: MPLS GSO support [ 2.712184] ThumbEE CPU extension supported. [ 2.715998] Registering SWP/SWPB emulation handler [ 2.721272] registered taskstats version 1 [ 2.724874] Loading compiled-in X.509 certificates [ 3.181482] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.188795] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.199867] zswap: loaded using pool lzo/zbud [ 3.203861] Key type .fscrypt registered [ 3.207128] Key type fscrypt-provisioning registered [ 3.231377] Key type encrypted registered [ 3.233974] AppArmor: AppArmor sha1 policy hashing enabled [ 3.239464] ima: No TPM chip found, activating TPM-bypass! [ 3.244905] ima: Allocated hash algorithm: sha256 [ 3.249613] ima: No architecture policies found [ 3.254128] evm: Initialising EVM extended attributes: [ 3.259199] evm: security.selinux [ 3.262488] evm: security.SMACK64 (disabled) [ 3.266742] evm: security.SMACK64EXEC (disabled) [ 3.271344] evm: security.SMACK64TRANSMUTE (disabled) [ 3.276376] evm: security.SMACK64MMAP (disabled) [ 3.280976] evm: security.apparmor [ 3.284361] evm: security.ima [ 3.287312] evm: security.capability [ 3.290877] evm: HMAC attrs: 0x1 [ 3.874439] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.880406] clk: Disabling unused clocks [ 3.893329] Freeing unused kernel image (initmem) memory: 2048K [ 3.898205] Checked W+X mappings: passed, no W+X pages found [ 3.903447] Run /init as init process [ 3.907076] with arguments: [ 3.907083] /init [ 3.907090] with environment: [ 3.907095] HOME=/ [ 3.907101] TERM=linux [ 4.836324] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.847006] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.859825] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.872001] usbcore: registered new interface driver usbfs [ 4.876534] usbcore: registered new interface driver hub [ 4.882531] usbcore: registered new device driver usb [ 4.891852] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 4.897389] exynos-ehci 12110000.usb: EHCI Host Controller [ 4.902892] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 4.920498] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 4.924492] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 4.942210] Synopsys Designware Multimedia Card Interface Driver [ 4.948132] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 4.953077] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 4.961045] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.968213] usb usb1: Product: EHCI Host Controller [ 4.973067] usb usb1: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 4.979588] usb usb1: SerialNumber: 12110000.usb [ 4.989177] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.995019] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.996361] exynos-ohci 12120000.usb: USB Host Controller [ 5.010030] hub 1-0:1.0: USB hub found [ 5.013556] hub 1-0:1.0: 3 ports detected [ 5.021408] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.039401] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 5.044430] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 5.050033] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 5.056240] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.061751] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.091243] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.110430] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.111434] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.133769] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.140609] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.147799] usb usb2: Product: USB Host Controller [ 5.152570] usb usb2: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 5.153526] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.159076] usb usb2: SerialNumber: 12120000.usb [ 5.185795] mmc_host mmc1: card is polling. [ 5.213488] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.236719] hub 2-0:1.0: USB hub found [ 5.239158] hub 2-0:1.0: 3 ports detected [ 5.252899] SCSI subsystem initialized [ 5.290743] libata version 3.00 loaded. [ 5.297564] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.314999] mmc0: new high speed SDHC card at address aaaa [ 5.323900] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.332075] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.338145] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.341834] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.346707] mmcblk0: mmc0:aaaa SU04G 3.69 GiB [ 5.363763] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.369463] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.378225] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.392789] scsi host0: ahci-dwc [ 5.393633] mmc1: new DDR MMC card at address 0001 [ 5.395178] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.425584] mmcblk1: mmc1:0001 M4G1FB 3.64 GiB [ 5.451333] mmcblk1: p1 p2 p3 p4 [ 5.460946] mmcblk1boot0: mmc1:0001 M4G1FB 1.00 MiB [ 5.478798] mmcblk1boot1: mmc1:0001 M4G1FB 1.00 MiB [ 5.496005] mmcblk1rpmb: mmc1:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.810592] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.884722] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.885521] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.900008] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.905864] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.913315] ata1.00: configured for UDMA/133 [ 5.917150] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.983747] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.987832] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.996744] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.004968] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.014714] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.018773] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.026505] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.029519] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.042501] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.050586] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.057737] usb usb3: Product: xHCI Host Controller [ 6.062595] usb usb3: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.069115] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.075297] hub 3-0:1.0: USB hub found [ 6.077740] hub 3-0:1.0: 1 port detected [ 6.082191] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.083276] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.090371] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.097156] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.105413] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.110677] sd 0:0:0:0: [sda] Write Protect is off [ 6.117787] usb usb4: Product: xHCI Host Controller [ 6.122558] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.127421] usb usb4: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.127516] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.133937] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.134966] hub 4-0:1.0: USB hub found [ 6.143140] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.147897] hub 4-0:1.0: 1 port detected [ 6.162148] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.189000] sda: sda1 sda2 < sda5 > [ 6.193572] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.251663] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.359738] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.519494] I/O error, dev mmcblk0, sector 7743712 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 6.636757] I/O error, dev mmcblk0, sector 7743714 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 6.914455] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 6.987797] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 7.101916] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.209518] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.217450] random: crng init done [ 7.317125] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.327692] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.338567] device-mapper: uevent: version 1.0.3 [ 7.343305] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.424752] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.432273] Buffer I/O error on dev mmcblk0, logical block 967954, async page read [ 11.143014] PM: Image not found (code -22) [ 11.681294] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.941565] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.262021] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.777504] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.812579] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.845922] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.906924] panfrost 11800000.gpu: clock rate = 533000000 [ 16.003085] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 16.009400] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 16.017584] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 16.029279] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 16.049497] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 16.109486] usb3503 usb-hub: switched to HUB mode [ 16.112735] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.161464] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.231659] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.366909] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.437506] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.475314] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.583650] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.602066] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.608950] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.619647] hub 1-3:1.0: USB hub found [ 16.622333] hub 1-3:1.0: 3 ports detected [ 16.691808] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.779014] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.850443] I/O error, dev mmcblk0, sector 7743712 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 16.929815] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.971900] I/O error, dev mmcblk0, sector 7743714 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 17.059286] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 17.066348] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 17.073581] usb 1-3.2: Product: USB2.0 Hub [ 17.083685] I/O error, dev mmcblk0, sector 7743715 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 17.098661] hub 1-3.2:1.0: USB hub found [ 17.102316] hub 1-3.2:1.0: 4 ports detected [ 17.369610] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 17.401574] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.443173] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.523900] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.531173] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.538655] usb 1-3.2.4: Product: AX88772 [ 17.542694] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.547881] usb 1-3.2.4: SerialNumber: 000001 [ 17.558202] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.666206] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.787275] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.795223] Buffer I/O error on dev mmcblk0, logical block 967954, async page read [ 18.096618] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.792223] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.807891] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.822427] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 82:ea:76:bf:8a:24 [ 18.834042] usbcore: registered new interface driver asix [ 19.600296] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.923676] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.975712] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 22.225051] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 23.363920] audit: type=1400 audit(1719088047.520:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=880 comm="apparmor_parser" [ 23.379610] audit: type=1400 audit(1719088047.520:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=880 comm="apparmor_parser" [ 23.395034] audit: type=1400 audit(1719088047.536:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=879 comm="apparmor_parser" [ 23.737763] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.777555] audit: type=1400 audit(1719088047.936:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=921 comm="apparmor_parser" [ 23.797132] audit: type=1400 audit(1719088047.952:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=921 comm="apparmor_parser" [ 23.810586] audit: type=1400 audit(1719088047.952:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=921 comm="apparmor_parser" [ 24.106089] audit: type=1400 audit(1719088048.264:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=919 comm="apparmor_parser" [ 24.125519] audit: type=1400 audit(1719088048.264:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=919 comm="apparmor_parser" [ 24.141401] audit: type=1400 audit(1719088048.264:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=919 comm="apparmor_parser" [ 24.158944] audit: type=1400 audit(1719088048.264:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=919 comm="apparmor_parser" [ 25.895404] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.901511] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.899973] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.911105] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.918841] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.925577] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.934166] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.948373] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.961688] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.990617] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.996341] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.002878] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1