[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-21-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.90-1 (2024-05-03) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015524K/2097152K available (12288K kernel code, 1714K rwdata, 3748K rodata, 2048K init, 382K bss, 65244K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39974 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000018] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002624] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002640] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002654] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002666] Ignoring duplicate/late registration of read_current_timer delay [ 0.003030] Console: colour dummy device 80x30 [ 0.003071] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003085] CPU: Testing write buffer coherency: ok [ 0.003125] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003133] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003140] pid_max: default: 32768 minimum: 301 [ 0.003498] LSM: Security Framework initializing [ 0.003571] landlock: Up and running. [ 0.003576] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003760] AppArmor: AppArmor initialized [ 0.003772] TOMOYO Linux initialized [ 0.003817] LSM support for eBPF active [ 0.004062] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004076] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005484] /cpus/cpu@0 missing clock-frequency property [ 0.005512] /cpus/cpu@1 missing clock-frequency property [ 0.005525] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006483] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006490] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006595] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006600] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006739] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007896] rcu: Hierarchical SRCU implementation. [ 0.007901] rcu: Max phase no-delay instances is 1000. [ 0.010027] EFI services will not be available. [ 0.010373] smp: Bringing up secondary CPUs ... [ 0.011118] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011130] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011272] smp: Brought up 1 node, 2 CPUs [ 0.011281] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011288] CPU: All CPU(s) started in HYP mode. [ 0.011293] CPU: Virtualization extensions available. [ 0.012164] devtmpfs: initialized [ 0.023680] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023920] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023945] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024512] pinctrl core: initialized pinctrl subsystem [ 0.025257] DMI not present or invalid. [ 0.025934] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027491] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.029064] audit: initializing netlink subsys (disabled) [ 0.029271] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030482] thermal_sys: Registered thermal governor 'fair_share' [ 0.030490] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030494] thermal_sys: Registered thermal governor 'step_wise' [ 0.030498] thermal_sys: Registered thermal governor 'user_space' [ 0.030503] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030708] No ATAGs? [ 0.030775] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030783] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031888] Serial: AMBA PL011 UART driver [ 0.085343] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.092608] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.095836] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.095845] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.102741] iommu: Default domain type: Translated [ 0.102750] iommu: DMA domain TLB invalidation policy: strict mode [ 0.103749] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.104285] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.104297] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.104944] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.104974] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.105179] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.105534] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.105545] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.105932] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.106221] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.106231] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.106532] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.106650] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.106659] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.106845] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.107058] pps_core: LinuxPPS API ver. 1 registered [ 0.107063] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.107079] PTP clock support registered [ 0.108594] NetLabel: Initializing [ 0.108599] NetLabel: domain hash size = 128 [ 0.108604] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.108659] NetLabel: unlabeled traffic allowed by default [ 0.108832] vgaarb: loaded [ 0.109331] clocksource: Switched to clocksource mct-frc [ 0.109914] VFS: Disk quotas dquot_6.6.0 [ 0.109999] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.110752] AppArmor: AppArmor Filesystem Enabled [ 0.120970] NET: Registered PF_INET protocol family [ 0.121172] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.122664] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.122766] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.122791] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.122890] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.123121] TCP: Hash tables configured (established 8192 bind 8192) [ 0.123355] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.123447] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123489] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123714] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.123749] NET: Registered PF_XDP protocol family [ 0.123760] PCI: CLS 0 bytes, default 64 [ 0.124280] Trying to unpack rootfs image as initramfs... [ 0.124619] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.130064] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.196087] Initialise system trusted keyrings [ 0.196178] Key type blacklist registered [ 0.197434] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.205690] zbud: loaded [ 0.208843] integrity: Platform Keyring initialized [ 0.208889] integrity: Machine keyring initialized [ 0.208899] Key type asymmetric registered [ 0.208906] Asymmetric key parser 'x509' registered [ 1.430970] Freeing initrd memory: 25116K [ 1.453236] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.453544] bounce: pool size: 64 pages [ 1.453730] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.453912] io scheduler mq-deadline registered [ 1.459058] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.480182] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.480193] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.482641] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.482651] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.483479] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.483488] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.484324] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.484332] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.486725] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.489545] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.492317] Serial: AMBA driver [ 1.492546] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.493031] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.493567] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.574376] printk: console [ttySAC2] enabled [ 2.579202] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.589898] STM32 USART driver initialized [ 2.604281] mousedev: PS/2 mouse device common for all mice [ 2.635539] s5m-rtc s5m-rtc: registered as rtc0 [ 2.644166] s5m-rtc s5m-rtc: setting system clock to 2024-06-22T16:30:15 UTC (1719073815) [ 2.654076] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.661578] ledtrig-cpu: registered to indicate activity on CPUs [ 2.669606] NET: Registered PF_INET6 protocol family [ 2.693772] Segment Routing with IPv6 [ 2.696010] In-situ OAM (IOAM) with IPv6 [ 2.700004] mip6: Mobile IPv6 [ 2.702855] NET: Registered PF_PACKET protocol family [ 2.708017] mpls_gso: MPLS GSO support [ 2.712052] ThumbEE CPU extension supported. [ 2.715864] Registering SWP/SWPB emulation handler [ 2.721127] registered taskstats version 1 [ 2.724738] Loading compiled-in X.509 certificates [ 3.181459] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.188781] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.199858] zswap: loaded using pool lzo/zbud [ 3.203810] Key type .fscrypt registered [ 3.207106] Key type fscrypt-provisioning registered [ 3.231494] Key type encrypted registered [ 3.234090] AppArmor: AppArmor sha1 policy hashing enabled [ 3.239557] ima: No TPM chip found, activating TPM-bypass! [ 3.245018] ima: Allocated hash algorithm: sha256 [ 3.249734] ima: No architecture policies found [ 3.254246] evm: Initialising EVM extended attributes: [ 3.259315] evm: security.selinux [ 3.262607] evm: security.SMACK64 (disabled) [ 3.266855] evm: security.SMACK64EXEC (disabled) [ 3.271454] evm: security.SMACK64TRANSMUTE (disabled) [ 3.276489] evm: security.SMACK64MMAP (disabled) [ 3.281089] evm: security.apparmor [ 3.284474] evm: security.ima [ 3.287426] evm: security.capability [ 3.290991] evm: HMAC attrs: 0x1 [ 3.874692] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.880664] clk: Disabling unused clocks [ 3.893607] Freeing unused kernel image (initmem) memory: 2048K [ 3.898461] Checked W+X mappings: passed, no W+X pages found [ 3.903724] Run /init as init process [ 3.907361] with arguments: [ 3.907369] /init [ 3.907375] with environment: [ 3.907381] HOME=/ [ 3.907387] TERM=linux [ 4.854491] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.868594] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.882279] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.906496] usbcore: registered new interface driver usbfs [ 4.910617] usbcore: registered new interface driver hub [ 4.944636] Synopsys Designware Multimedia Card Interface Driver [ 4.952801] SCSI subsystem initialized [ 4.979128] usbcore: registered new device driver usb [ 4.983771] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.990023] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 5.013094] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 5.018123] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 5.025418] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 5.028909] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.030434] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.081693] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107,32 bit host data width,128 deep fifo [ 5.115013] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.130265] mmc_host mmc0: card is polling. [ 5.150745] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.159144] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.188820] phy phy-12130000.phy.1: phy_power_on was called before phy_init [ 5.195676] phy phy-12130000.phy.1: phy_power_on was called before phy_init [ 5.203360] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.209635] exynos-ohci 12120000.usb: USB Host Controller [ 5.231467] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 5.233981] libata version 3.00 loaded. [ 5.246681] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 5.260112] exynos-ohci 12120000.usb: irq 109, io mem 0x12120000 [ 5.264999] exynos-ehci 12110000.usb: irq 109, io mem 0x12110000 [ 5.274518] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.278207] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.293023] mmc1: new high speed SDHC card at address aaaa [ 5.299846] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.306894] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.309692] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.314348] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.323170] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.333589] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.337919] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.340507] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.348723] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.357556] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.364765] usb usb1: Product: USB Host Controller [ 5.378665] usb usb1: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 5.385164] usb usb1: SerialNumber: 12120000.usb [ 5.415012] mmc0: new DDR MMC card at address 0001 [ 5.415132] scsi host0: ahci-dwc [ 5.422977] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.435119] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.450551] mmcblk0: p1 p2 p3 p4 [ 5.460216] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.485967] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.500097] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.508209] hub 1-0:1.0: USB hub found [ 5.510610] hub 1-0:1.0: 3 ports detected [ 5.530931] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.537797] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.544959] usb usb2: Product: EHCI Host Controller [ 5.549814] usb usb2: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 5.556323] usb usb2: SerialNumber: 12110000.usb [ 5.561721] hub 2-0:1.0: USB hub found [ 5.564674] hub 2-0:1.0: 3 ports detected [ 5.786037] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.859313] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.905381] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.910945] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.916795] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.924233] ata1.00: configured for UDMA/133 [ 5.928011] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.992736] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.020078] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.024172] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 6.032835] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.041216] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.047467] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.052669] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.060370] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.066941] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.075008] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.082212] usb usb3: Product: xHCI Host Controller [ 6.087064] usb usb3: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.093567] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.100869] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.100977] hub 3-0:1.0: USB hub found [ 6.112611] hub 3-0:1.0: 1 port detected [ 6.113515] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.118716] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.123935] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.132187] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.145485] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.145548] sd 0:0:0:0: [sda] Write Protect is off [ 6.152653] usb usb4: Product: xHCI Host Controller [ 6.152661] usb usb4: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.157424] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.162284] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.168905] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.176609] hub 4-0:1.0: USB hub found [ 6.182865] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.186462] hub 4-0:1.0: 1 port detected [ 6.208948] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.216979] sda: sda1 sda2 < sda5 > [ 6.221114] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.317039] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.481582] I/O error, dev mmcblk1, sector 7743713 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 6.590205] I/O error, dev mmcblk1, sector 7743714 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 6.698218] I/O error, dev mmcblk1, sector 7743715 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 6.976175] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 7.050286] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 7.164367] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.271976] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.289353] random: crng init done [ 7.379586] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.404768] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.415604] device-mapper: uevent: version 1.0.3 [ 7.421419] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.487271] Buffer I/O error on dev mmcblk1, logical block 967954, async page read [ 11.248576] PM: Image not found (code -22) [ 11.786054] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.021460] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.354944] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 16.042575] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 16.076021] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 16.199149] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 16.325052] panfrost 11800000.gpu: clock rate = 533000000 [ 16.373381] usb3503 usb-hub: switched to HUB mode [ 16.376626] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.452703] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 16.459016] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 16.467165] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 16.478876] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 16.487322] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 16.668449] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.701502] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 16.759491] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.868632] blk_print_req_error: 1 callbacks suppressed [ 16.868643] I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 16.886168] usb 2-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.892921] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.904592] hub 2-3:1.0: USB hub found [ 16.907483] hub 2-3:1.0: 3 ports detected [ 16.981960] I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.079669] OF: graph: no port node found in /soc/hdmi@14530000 [ 17.090084] I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.197392] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.203041] I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.312534] I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.328478] usb 2-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 17.335573] usb 2-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 17.342832] usb 2-3.2: Product: USB2.0 Hub [ 17.353750] hub 2-3.2:1.0: USB hub found [ 17.356587] hub 2-3.2:1.0: 4 ports detected [ 17.420896] I/O error, dev mmcblk1, sector 7744005 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.529235] I/O error, dev mmcblk1, sector 7744006 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.638313] I/O error, dev mmcblk1, sector 7744007 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 2 [ 17.665398] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.746466] I/O error, dev mmcblk1, sector 7744008 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 17.783906] usb 2-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.791180] usb 2-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.798662] usb 2-3.2.4: Product: AX88772 [ 17.802691] usb 2-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.807860] usb 2-3.2.4: SerialNumber: 000001 [ 17.854723] I/O error, dev mmcblk1, sector 7744009 op 0x0:(READ) flags 0x80700 phys_seg 13 prio class 2 [ 18.448900] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 19.135986] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 19.151536] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 19.165466] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 46:1c:52:45:d6:ed [ 19.180714] usbcore: registered new interface driver asix [ 20.781639] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 21.346960] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 23.659376] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 23.711287] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 23.938456] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 25.244265] audit: type=1400 audit(1719073836.964:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=898 comm="apparmor_parser" [ 25.260665] audit: type=1400 audit(1719073836.964:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=897 comm="apparmor_parser" [ 25.274359] audit: type=1400 audit(1719073836.964:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=898 comm="apparmor_parser" [ 25.335661] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 25.628823] audit: type=1400 audit(1719073837.348:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=941 comm="apparmor_parser" [ 25.647952] audit: type=1400 audit(1719073837.364:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=941 comm="apparmor_parser" [ 25.661380] audit: type=1400 audit(1719073837.368:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=941 comm="apparmor_parser" [ 25.949916] audit: type=1400 audit(1719073837.672:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=940 comm="apparmor_parser" [ 25.966543] audit: type=1400 audit(1719073837.672:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=940 comm="apparmor_parser" [ 25.983659] audit: type=1400 audit(1719073837.672:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=940 comm="apparmor_parser" [ 26.001208] audit: type=1400 audit(1719073837.672:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=940 comm="apparmor_parser" [ 27.495043] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 27.501096] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 29.408686] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 29.419591] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 29.427432] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 29.433825] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 29.442347] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 29.451837] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 29.458686] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 29.467758] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.474311] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.486230] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1