[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-21-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.90-1 (2024-05-03) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015524K/2097152K available (12288K kernel code, 1714K rwdata, 3748K rodata, 2048K init, 382K bss, 65244K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39974 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002629] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002644] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002659] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002670] Ignoring duplicate/late registration of read_current_timer delay [ 0.003034] Console: colour dummy device 80x30 [ 0.003074] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003088] CPU: Testing write buffer coherency: ok [ 0.003129] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003137] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003143] pid_max: default: 32768 minimum: 301 [ 0.003506] LSM: Security Framework initializing [ 0.003578] landlock: Up and running. [ 0.003583] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003768] AppArmor: AppArmor initialized [ 0.003780] TOMOYO Linux initialized [ 0.003826] LSM support for eBPF active [ 0.004073] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004087] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005505] /cpus/cpu@0 missing clock-frequency property [ 0.005533] /cpus/cpu@1 missing clock-frequency property [ 0.005547] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006507] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006514] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006620] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006625] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006765] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007922] rcu: Hierarchical SRCU implementation. [ 0.007928] rcu: Max phase no-delay instances is 1000. [ 0.010064] EFI services will not be available. [ 0.010409] smp: Bringing up secondary CPUs ... [ 0.011154] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011166] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011299] smp: Brought up 1 node, 2 CPUs [ 0.011308] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011316] CPU: All CPU(s) started in HYP mode. [ 0.011319] CPU: Virtualization extensions available. [ 0.012188] devtmpfs: initialized [ 0.023702] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023941] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023966] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024522] pinctrl core: initialized pinctrl subsystem [ 0.025264] DMI not present or invalid. [ 0.025942] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027503] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.029079] audit: initializing netlink subsys (disabled) [ 0.029285] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030494] thermal_sys: Registered thermal governor 'fair_share' [ 0.030501] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030506] thermal_sys: Registered thermal governor 'step_wise' [ 0.030510] thermal_sys: Registered thermal governor 'user_space' [ 0.030515] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030720] No ATAGs? [ 0.030789] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030796] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031895] Serial: AMBA PL011 UART driver [ 0.081353] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.088625] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091867] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091875] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.098770] iommu: Default domain type: Translated [ 0.098779] iommu: DMA domain TLB invalidation policy: strict mode [ 0.099759] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100293] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100305] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.100949] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.100980] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101185] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.101542] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.101553] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.101940] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102235] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102245] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.102547] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.102664] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.102674] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.102859] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103075] pps_core: LinuxPPS API ver. 1 registered [ 0.103080] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103097] PTP clock support registered [ 0.104624] NetLabel: Initializing [ 0.104630] NetLabel: domain hash size = 128 [ 0.104635] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.104689] NetLabel: unlabeled traffic allowed by default [ 0.104863] vgaarb: loaded [ 0.105350] clocksource: Switched to clocksource mct-frc [ 0.105931] VFS: Disk quotas dquot_6.6.0 [ 0.106014] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.106766] AppArmor: AppArmor Filesystem Enabled [ 0.117028] NET: Registered PF_INET protocol family [ 0.117226] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.118717] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.118819] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.118844] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.118944] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119176] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119404] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.119498] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119540] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119758] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.119796] NET: Registered PF_XDP protocol family [ 0.119810] PCI: CLS 0 bytes, default 64 [ 0.120302] Trying to unpack rootfs image as initramfs... [ 0.120676] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126051] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.191840] Initialise system trusted keyrings [ 0.191930] Key type blacklist registered [ 0.193133] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.201471] zbud: loaded [ 0.204747] integrity: Platform Keyring initialized [ 0.204779] integrity: Machine keyring initialized [ 0.204789] Key type asymmetric registered [ 0.204797] Asymmetric key parser 'x509' registered [ 1.423874] Freeing initrd memory: 25116K [ 1.446273] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.446545] bounce: pool size: 64 pages [ 1.446729] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.446922] io scheduler mq-deadline registered [ 1.452033] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.473096] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473109] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.475513] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.475522] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.476361] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.476371] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.477217] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.477225] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.479572] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.482409] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.485190] Serial: AMBA driver [ 1.485458] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.485946] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.486442] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.567251] printk: console [ttySAC2] enabled [ 2.572079] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.582766] STM32 USART driver initialized [ 2.597235] mousedev: PS/2 mouse device common for all mice [ 2.628438] s5m-rtc s5m-rtc: registered as rtc0 [ 2.637061] s5m-rtc s5m-rtc: setting system clock to 2024-06-23T10:36:26 UTC (1719138986) [ 2.646927] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.654439] ledtrig-cpu: registered to indicate activity on CPUs [ 2.662446] NET: Registered PF_INET6 protocol family [ 2.686649] Segment Routing with IPv6 [ 2.688894] In-situ OAM (IOAM) with IPv6 [ 2.692860] mip6: Mobile IPv6 [ 2.695730] NET: Registered PF_PACKET protocol family [ 2.700899] mpls_gso: MPLS GSO support [ 2.704921] ThumbEE CPU extension supported. [ 2.708756] Registering SWP/SWPB emulation handler [ 2.713973] registered taskstats version 1 [ 2.717624] Loading compiled-in X.509 certificates [ 3.173652] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.180967] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.192049] zswap: loaded using pool lzo/zbud [ 3.196010] Key type .fscrypt registered [ 3.199302] Key type fscrypt-provisioning registered [ 3.223483] Key type encrypted registered [ 3.226081] AppArmor: AppArmor sha1 policy hashing enabled [ 3.231537] ima: No TPM chip found, activating TPM-bypass! [ 3.237005] ima: Allocated hash algorithm: sha256 [ 3.241725] ima: No architecture policies found [ 3.246258] evm: Initialising EVM extended attributes: [ 3.251306] evm: security.selinux [ 3.254595] evm: security.SMACK64 (disabled) [ 3.258845] evm: security.SMACK64EXEC (disabled) [ 3.263449] evm: security.SMACK64TRANSMUTE (disabled) [ 3.268484] evm: security.SMACK64MMAP (disabled) [ 3.273080] evm: security.apparmor [ 3.276468] evm: security.ima [ 3.279416] evm: security.capability [ 3.282984] evm: HMAC attrs: 0x1 [ 3.866752] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.872727] clk: Disabling unused clocks [ 3.885666] Freeing unused kernel image (initmem) memory: 2048K [ 3.890524] Checked W+X mappings: passed, no W+X pages found [ 3.895783] Run /init as init process [ 3.899419] with arguments: [ 3.899427] /init [ 3.899434] with environment: [ 3.899439] HOME=/ [ 3.899445] TERM=linux [ 4.828158] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.839776] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.878332] usbcore: registered new interface driver usbfs [ 4.883043] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.891228] usbcore: registered new interface driver hub [ 4.898183] usbcore: registered new device driver usb [ 4.912616] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 4.919498] Synopsys Designware Multimedia Card Interface Driver [ 4.924231] exynos-ohci 12120000.usb: USB Host Controller [ 4.932684] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.941769] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.966137] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 4.975490] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.980509] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.999354] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.000242] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 5.009424] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 5.029644] SCSI subsystem initialized [ 5.032953] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 5.053385] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.067509] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 5.075091] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.092198] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.109024] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.117329] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 5.123164] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.134610] mmc_host mmc1: card is polling. [ 5.149421] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.160205] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.167040] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.174232] usb usb1: Product: USB Host Controller [ 5.179000] usb usb1: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 5.185505] usb usb1: SerialNumber: 12120000.usb [ 5.190929] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.202458] hub 1-0:1.0: USB hub found [ 5.208081] hub 1-0:1.0: 3 ports detected [ 5.222803] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.229661] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.236824] usb usb2: Product: EHCI Host Controller [ 5.241689] usb usb2: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 5.248216] usb usb2: SerialNumber: 12110000.usb [ 5.257531] hub 2-0:1.0: USB hub found [ 5.259920] hub 2-0:1.0: 3 ports detected [ 5.294893] libata version 3.00 loaded. [ 5.296971] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.307803] mmc0: new high speed SDHC card at address aaaa [ 5.317094] mmcblk0: mmc0:aaaa SU04G 3.69 GiB [ 5.326604] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.351184] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.361071] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.367209] mmc1: new DDR MMC card at address 0001 [ 5.381318] mmcblk1: mmc1:0001 M4G1FB 3.64 GiB [ 5.383301] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.399441] mmcblk1: p1 p2 p3 p4 [ 5.403043] mmcblk1boot0: mmc1:0001 M4G1FB 1.00 MiB [ 5.406897] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.413629] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.422440] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.434978] mmcblk1boot1: mmc1:0001 M4G1FB 1.00 MiB [ 5.440990] mmcblk1rpmb: mmc1:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.449194] scsi host0: ahci-dwc [ 5.451419] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.718389] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.791808] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.925181] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 5.937419] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.942983] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.948835] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.956284] ata1.00: configured for UDMA/133 [ 5.960712] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 6.025514] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.029581] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 6.037259] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.049893] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.057966] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.064157] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.069526] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.077051] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.083673] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.091720] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.098909] usb usb3: Product: xHCI Host Controller [ 6.103769] usb usb3: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.110273] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.115878] hub 3-0:1.0: USB hub found [ 6.117443] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.118928] hub 3-0:1.0: 1 port detected [ 6.126347] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.130989] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.135523] sd 0:0:0:0: [sda] Write Protect is off [ 6.144874] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.148358] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.156543] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.157538] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.163772] usb usb4: Product: xHCI Host Controller [ 6.177974] usb usb4: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.178252] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.184483] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.185579] hub 4-0:1.0: USB hub found [ 6.194185] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.198635] hub 4-0:1.0: 1 port detected [ 6.231297] sda: sda1 sda2 < sda5 > [ 6.235725] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.273218] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 6.599466] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 6.670428] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 6.785976] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 6.893585] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.001194] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.108786] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.116292] Buffer I/O error on dev mmcblk0, logical block 967954, async page read [ 7.229372] random: crng init done [ 7.338539] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.349398] device-mapper: uevent: version 1.0.3 [ 7.354121] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 11.118909] PM: Image not found (code -22) [ 11.660777] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.928292] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.244521] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.788858] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.864785] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.926666] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 16.005106] panfrost 11800000.gpu: clock rate = 533000000 [ 16.118801] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 16.125121] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 16.133373] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 16.144990] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 16.177484] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.201402] usb3503 usb-hub: switched to HUB mode [ 16.204641] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.214424] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 16.246271] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.384747] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.497404] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.525619] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 16.605616] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.694298] usb 2-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.701208] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.710503] hub 2-3:1.0: USB hub found [ 16.713056] hub 2-3:1.0: 3 ports detected [ 16.744522] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.773117] I/O error, dev mmcblk0, sector 7743713 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 17.009558] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.061222] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 17.133076] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.147743] usb 2-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 17.154770] usb 2-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 17.162105] usb 2-3.2: Product: USB2.0 Hub [ 17.175231] hub 2-3.2:1.0: USB hub found [ 17.178268] hub 2-3.2:1.0: 4 ports detected [ 17.247550] I/O error, dev mmcblk0, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.355211] I/O error, dev mmcblk0, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.462840] I/O error, dev mmcblk0, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.477443] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.570620] I/O error, dev mmcblk0, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.578365] Buffer I/O error on dev mmcblk0, logical block 967954, async page read [ 17.612883] usb 2-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.620102] usb 2-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.627520] usb 2-3.2.4: Product: AX88772 [ 17.631699] usb 2-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.636772] usb 2-3.2.4: SerialNumber: 000001 [ 18.204295] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.872035] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.887572] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 18.899492] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, e6:7b:46:c0:2b:d8 [ 18.916159] usbcore: registered new interface driver asix [ 19.809868] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.532638] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.584671] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 21.852529] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 23.462388] audit: type=1400 audit(1719139006.856:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=906 comm="apparmor_parser" [ 23.475979] audit: type=1400 audit(1719139006.860:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=907 comm="apparmor_parser" [ 23.491242] audit: type=1400 audit(1719139006.860:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=907 comm="apparmor_parser" [ 23.641068] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.871994] audit: type=1400 audit(1719139007.264:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=944 comm="apparmor_parser" [ 23.889440] audit: type=1400 audit(1719139007.268:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=944 comm="apparmor_parser" [ 23.902921] audit: type=1400 audit(1719139007.268:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=944 comm="apparmor_parser" [ 24.243665] audit: type=1400 audit(1719139007.632:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=943 comm="apparmor_parser" [ 24.260466] audit: type=1400 audit(1719139007.636:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=943 comm="apparmor_parser" [ 24.277413] audit: type=1400 audit(1719139007.636:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=943 comm="apparmor_parser" [ 24.294966] audit: type=1400 audit(1719139007.636:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=943 comm="apparmor_parser" [ 25.799345] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.805457] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 29.152656] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 29.163676] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 29.171422] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 29.177766] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 29.186536] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 29.195816] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 29.202582] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 29.212001] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.218369] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.227094] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1