[ 0.000000] Linux version 6.10.0-rc4+ (osstest@himrod1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Sun Jun 23 16:53:02 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000095fff] usable [ 0.000000] Xen: [mem 0x0000000000096000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020069fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SCM/H8SCM, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000014] Xen PV: Detected 6 vCPUS [ 0.037802] tsc: Fast TSC calibration using PIT [ 0.037804] tsc: Detected 3101.087 MHz processor [ 0.037806] tsc: Detected 3101.110 MHz TSC [ 0.038021] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.038025] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.038031] last_pfn = 0x2006a max_arch_pfn = 0x400000000 [ 0.038036] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.038038] MTRRs set to read-only [ 0.038042] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.062674] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.062703] ACPI: Early table checksum verification disabled [ 0.064224] ACPI: RSDP 0x00000000000FA1D0 000024 (v02 ACPIAM) [ 0.064238] ACPI: XSDT 0x00000000DFEA0100 000084 (v01 SMCI 20131125 MSFT 00000097) [ 0.064281] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.064344] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.064356] ACPI: DSDT 0x00000000DFEA0600 005699 (v01 1BA11 1BA11000 00000000 INTL 20051117) [ 0.064367] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.064377] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.064388] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.064400] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.064450] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.064461] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.064473] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.064484] ACPI: SRAT 0x00000000DFEAA6F0 000108 (v02 AMD AGESA 00000001 AMD 00000001) [ 0.064495] ACPI: SSDT 0x00000000DFEAA800 001158 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.064506] ACPI: EINJ 0x00000000DFEAB960 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.064517] ACPI: BERT 0x00000000DFEABAF0 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.064528] ACPI: ERST 0x00000000DFEABB20 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.064539] ACPI: HEST 0x00000000DFEABD30 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.064545] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.064547] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c98] [ 0.064548] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.064550] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.064551] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.064552] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.064553] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.064554] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.064556] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.064557] ACPI: Reserving SRAT table memory at [mem 0xdfeaa6f0-0xdfeaa7f7] [ 0.064558] ACPI: Reserving SSDT table memory at [mem 0xdfeaa800-0xdfeab957] [ 0.064559] ACPI: Reserving EINJ table memory at [mem 0xdfeab960-0xdfeaba8f] [ 0.064560] ACPI: Reserving BERT table memory at [mem 0xdfeabaf0-0xdfeabb1f] [ 0.064561] ACPI: Reserving ERST table memory at [mem 0xdfeabb20-0xdfeabd2f] [ 0.064563] ACPI: Reserving HEST table memory at [mem 0xdfeabd30-0xdfeabdd7] [ 0.064700] APIC: Switched APIC routing to: Xen PV [ 0.066905] Zone ranges: [ 0.066908] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.066910] DMA32 [mem 0x0000000001000000-0x0000000020069fff] [ 0.066913] Normal empty [ 0.066914] Movable zone start for each node [ 0.066916] Early memory node ranges [ 0.066916] node 0: [mem 0x0000000000001000-0x0000000000095fff] [ 0.066919] node 0: [mem 0x0000000000100000-0x0000000020069fff] [ 0.066922] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020069fff] [ 0.066938] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.067075] On node 0, zone DMA: 106 pages in unavailable ranges [ 0.072660] On node 0, zone DMA32: 32662 pages in unavailable ranges [ 0.072679] p2m virtual area at (____ptrval____), size is 40000000 [ 0.280140] Remapped 106 page(s) [ 0.280655] ACPI: PM-Timer IO Port: 0x808 [ 0.280697] CPU topo: CPU limit of 6 reached. Ignoring further CPUs [ 0.280731] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.280736] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.280762] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.280771] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.280783] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.280790] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.280816] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.280821] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.280836] CPU topo: Max. logical packages: 1 [ 0.280838] CPU topo: Max. logical dies: 1 [ 0.280839] CPU topo: Max. dies per package: 1 [ 0.280846] CPU topo: Max. threads per core: 1 [ 0.280847] CPU topo: Num. cores per package: 6 [ 0.280848] CPU topo: Num. threads per package: 6 [ 0.280849] CPU topo: Allowing 6 present CPUs plus 0 hotplug CPUs [ 0.280850] CPU topo: Rejected CPUs 2 [ 0.280870] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.280873] PM: hibernation: Registered nosave memory: [mem 0x00096000-0x000fffff] [ 0.280877] [mem 0x2006a000-0xdfe9dfff] available for PCI devices [ 0.280881] Booting kernel on Xen [ 0.280883] Xen version: 4.19-unstable (preserve-AD) [ 0.280890] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.287233] setup_percpu: NR_CPUS:64 nr_cpumask_bits:6 nr_cpu_ids:6 nr_node_ids:1 [ 0.288571] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u262144 [ 0.288581] pcpu-alloc: s194408 r8192 d30872 u262144 alloc=1*2097152 [ 0.288587] pcpu-alloc: [0] 0 1 2 3 4 5 - - [ 0.288685] xen: PV spinlocks enabled [ 0.288691] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.288695] Kernel command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.288789] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.288857] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.288983] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.289248] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.289255] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.289259] software IO TLB: area num 8. [ 0.428781] Memory: 385988K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 138044K reserved, 0K cma-reserved) [ 0.428930] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.432043] Dynamic Preempt: voluntary [ 0.432194] rcu: Preemptible hierarchical RCU implementation. [ 0.432195] rcu: RCU event tracing is enabled. [ 0.432196] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.432199] Trampoline variant of Tasks RCU enabled. [ 0.432201] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.432202] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 [ 0.432229] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.438949] NR_IRQS: 4352, nr_irqs: 1016, preallocated irqs: 16 [ 0.439129] xen:events: Using FIFO-based ABI [ 0.439167] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.439174] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.439187] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.439192] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.439198] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.439203] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.439208] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.439212] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.439217] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.439222] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.439227] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.439232] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.439237] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.439243] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.439248] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.439263] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.445254] Console: colour VGA+ 80x25 [ 0.445260] printk: legacy console [tty0] enabled [ 0.458776] printk: legacy console [hvc0] enabled [ 0.459454] ACPI: Core revision 20240322 [ 0.465011] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.465169] Xen: using vcpuop timer interface [ 0.465176] installing Xen timer for CPU 0 [ 0.465430] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cb3604f57e, max_idle_ns: 440795281302 ns [ 0.465589] Calibrating delay loop (skipped), value calculated using timer frequency.. 6202.22 BogoMIPS (lpj=3101110) [ 0.465791] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.466011] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.466119] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.466236] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.466601] Spectre V2 : Mitigation: Retpolines [ 0.466703] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.466846] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.466955] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.467065] RETBleed: Mitigation: untrained return thunk [ 0.467172] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.467321] Speculative Store Bypass: Vulnerable [ 0.467477] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.467591] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.467700] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.467809] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.467919] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.495909] Freeing SMP alternatives memory: 40K [ 0.496063] pid_max: default: 32768 minimum: 301 [ 0.496203] LSM: initializing lsm=capability,selinux [ 0.496332] SELinux: Initializing. [ 0.496497] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.496594] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.497730] cpu 0 spinlock event irq 57 [ 0.497844] VPMU disabled by hypervisor. [ 0.498337] Performance Events: PMU not available due to virtualization, using software events only. [ 0.498497] signal: max sigframe size: 1776 [ 0.498660] rcu: Hierarchical SRCU implementation. [ 0.498766] rcu: Max phase no-delay instances is 400. [ 0.504829] smp: Bringing up secondary CPUs ... [ 0.505168] installing Xen timer for CPU 1 [ 0.505658] installing Xen timer for CPU 2 [ 0.506076] installing Xen timer for CPU 3 [ 0.506448] installing Xen timer for CPU 4 [ 0.506837] installing Xen timer for CPU 5 [ 0.027316] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.507067] cpu 1 spinlock event irq 87 [ 0.027316] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.507704] cpu 2 spinlock event irq 88 [ 0.027316] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.508830] cpu 3 spinlock event irq 89 [ 0.027316] [Firmware Bug]: CPU 4: APIC ID mismatch. CPUID: 0x0004 APIC: 0x0014 [ 0.509636] cpu 4 spinlock event irq 90 [ 0.027316] [Firmware Bug]: CPU 5: APIC ID mismatch. CPUID: 0x0005 APIC: 0x0015 [ 0.509882] cpu 5 spinlock event irq 91 [ 0.510781] smp: Brought up 1 node, 6 CPUs [ 0.511604] devtmpfs: initialized [ 0.511769] x86/mm: Memory block size: 128MB [ 0.512937] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.512937] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.513596] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.513996] PM: RTC time: 19:42:21, date: 2024-06-23 [ 0.514467] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.514840] xen:grant_table: Grant tables using version 1 layout [ 0.515586] Grant table initialized [ 0.518478] audit: initializing netlink subsys (disabled) [ 0.518734] audit: type=2000 audit(1719171742.120:1): state=initialized audit_enabled=0 res=1 [ 0.520081] thermal_sys: Registered thermal governor 'step_wise' [ 0.520097] thermal_sys: Registered thermal governor 'user_space' [ 0.523614] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.524484] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 1.136350] PCI: Using configuration type 1 for base access [ 1.137165] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 1.138683] ACPI: Added _OSI(Module Device) [ 1.138774] ACPI: Added _OSI(Processor Device) [ 1.138876] ACPI: Added _OSI(3.0 _SCP Extensions) [ 1.138980] ACPI: Added _OSI(Processor Aggregator Device) [ 1.147614] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 1.152622] xen: registering gsi 9 triggering 0 polarity 1 [ 1.156635] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 1.157406] ACPI: Interpreter enabled [ 1.157714] ACPI: PM: (supports S0 S1 S4 S5) [ 1.157932] ACPI: Using IOAPIC for interrupt routing [ 1.158127] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.158276] PCI: Using E820 reservations for host bridge windows [ 1.158559] ACPI: Enabled 4 GPEs in block 00 to 1F [ 1.186183] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 1.186326] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 1.186484] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 1.186590] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 1.186734] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 1.187255] PCI host bridge to bus 0000:00 [ 1.187359] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 1.187475] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 1.187590] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 1.187733] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 1.187876] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 1.188066] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.188234] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 1.188807] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 1.189339] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 1.189550] pci 0000:00:09.0: PCI bridge to [bus 01] [ 1.189604] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 1.189719] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 1.189881] pci 0000:00:09.0: enabling Extended Tags [ 1.190108] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 1.190400] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 1.190654] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 1.190772] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 1.190892] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 1.191082] pci 0000:00:0a.0: enabling Extended Tags [ 1.191305] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 1.191620] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601 conventional PCI endpoint [ 1.191808] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 1.191977] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 1.192110] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 1.192238] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 1.192367] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 1.192495] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 1.192831] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 1.193020] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 1.193441] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 1.193631] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 1.194036] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 1.194228] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 1.194552] pci 0000:00:12.2: supports D1 D2 [ 1.194590] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 1.194855] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 1.195043] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 1.195426] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 1.195615] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 1.196017] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 1.196205] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 1.196529] pci 0000:00:13.2: supports D1 D2 [ 1.196589] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 1.196875] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 1.197391] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 1.197579] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 1.197612] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 1.197739] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 1.197866] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 1.197993] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 1.198157] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 1.198269] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 1.198378] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 1.198489] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 1.198776] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 1.199274] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 1.199502] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 1.199606] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 1.199728] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 1.200012] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 1.200203] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 1.200612] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 1.200993] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 1.201345] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 1.201657] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 1.202007] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 1.202380] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 1.202844] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 1.203035] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 1.203204] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 1.203337] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 1.203698] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.206645] pci 0000:00:09.0: PCI bridge to [bus 01] [ 1.206978] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 1.207176] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 1.207351] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 1.207487] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 1.207856] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 1.210649] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 1.210855] pci_bus 0000:03: extended config space not accessible [ 1.211047] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 1.211241] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 1.211390] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 1.211616] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 1.211865] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 1.212332] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 1.212464] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 1.212590] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 1.212735] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 1.212883] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 1.213068] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 1.213288] pci_bus 0000:00: on NUMA node 0 [ 1.213987] xen: registering gsi 13 triggering 1 polarity 0 [ 1.214503] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 1.214673] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 1.214905] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 1.215107] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 1.215300] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 1.215489] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 1.215674] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 1.215865] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 1.216157] xen:balloon: Initialising balloon driver [ 1.216712] iommu: Default domain type: Translated [ 1.216847] iommu: DMA domain TLB invalidation policy: lazy mode [ 1.217124] SCSI subsystem initialized [ 1.217238] libata version 3.00 loaded. [ 1.217238] ACPI: bus type USB registered [ 1.217617] usbcore: registered new interface driver usbfs [ 1.217733] usbcore: registered new interface driver hub [ 1.217850] usbcore: registered new device driver usb [ 1.217982] pps_core: LinuxPPS API ver. 1 registered [ 1.218095] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.218260] PTP clock support registered [ 1.218656] Advanced Linux Sound Architecture Driver Initialized. [ 1.219101] NetLabel: Initializing [ 1.219201] NetLabel: domain hash size = 128 [ 1.219303] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 1.219431] NetLabel: unlabeled traffic allowed by default [ 1.219661] PCI: Using ACPI for IRQ routing [ 1.245178] PCI: pci_cache_line_size set to 64 bytes [ 1.245354] e820: reserve RAM buffer [mem 0x00096000-0x0009ffff] [ 1.245358] e820: reserve RAM buffer [mem 0x2006a000-0x23ffffff] [ 1.245391] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 1.245391] pci 0000:03:04.0: vgaarb: bridge control possible [ 1.245391] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 1.245590] vgaarb: loaded [ 1.248505] clocksource: Switched to clocksource tsc-early [ 1.248505] VFS: Disk quotas dquot_6.6.0 [ 1.248846] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.248874] hugetlbfs: disabling because there are no supported hugepage sizes [ 1.249854] pnp: PnP ACPI init [ 1.250298] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 1.250552] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 1.251049] xen: registering gsi 8 triggering 1 polarity 0 [ 1.251299] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 1.251661] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 1.251777] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 1.252287] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 1.252398] system 00:05: [io 0x0550-0x0551] has been reserved [ 1.252507] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 1.252629] system 00:05: [io 0x040b] has been reserved [ 1.252737] system 00:05: [io 0x04d6] has been reserved [ 1.252844] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 1.252952] system 00:05: [io 0x0c14] has been reserved [ 1.253059] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 1.253168] system 00:05: [io 0x0c52] has been reserved [ 1.253275] system 00:05: [io 0x0c6c] has been reserved [ 1.253422] system 00:05: [io 0x0c6f] has been reserved [ 1.253532] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 1.253653] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 1.253764] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 1.253873] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 1.253987] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 1.254097] system 00:05: [io 0x0800-0x089f] has been reserved [ 1.254206] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 1.254316] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 1.254424] system 00:05: [io 0x0900-0x090f] has been reserved [ 1.254534] system 00:05: [io 0x0910-0x091f] has been reserved [ 1.254655] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 1.254804] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 1.254916] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 1.255027] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 1.255425] xen: registering gsi 4 triggering 1 polarity 0 [ 1.255429] Already setup the GSI :4 [ 1.255530] pnp 00:06: [dma 0 disabled] [ 1.255887] xen: registering gsi 3 triggering 1 polarity 0 [ 1.255895] pnp 00:07: [dma 0 disabled] [ 1.256065] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 1.256517] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 1.256722] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 1.256836] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 1.256949] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 1.257063] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 1.257346] pnp: PnP ACPI: found 10 devices [ 1.283041] PM-Timer failed consistency check (0xffffff) - aborting. [ 1.283261] NET: Registered PF_INET protocol family [ 1.283506] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.284005] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.284157] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.284303] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.284467] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 1.284692] TCP: Hash tables configured (established 4096 bind 4096) [ 1.284929] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.285057] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.285262] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.285690] RPC: Registered named UNIX socket transport module. [ 1.286036] RPC: Registered udp transport module. [ 1.286355] RPC: Registered tcp transport module. [ 1.286631] RPC: Registered tcp-with-tls transport module. [ 1.286738] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.287447] pci 0000:00:09.0: PCI bridge to [bus 01] [ 1.287688] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 1.287808] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 1.287977] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 1.288086] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 1.288202] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 1.288332] pci 0000:00:14.4: PCI bridge to [bus 03] [ 1.288446] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 1.288563] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 1.288734] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 1.288844] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 1.288952] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 1.289064] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 1.289176] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 1.289329] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 1.289437] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 1.289548] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 1.289665] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 1.289777] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 1.289889] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 1.290002] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 1.290114] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 1.290224] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 1.290338] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 1.290450] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 1.291544] xen: registering gsi 16 triggering 0 polarity 1 [ 1.291682] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.941901] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 635602 usecs [ 1.942163] xen: registering gsi 16 triggering 0 polarity 1 [ 1.942177] Already setup the GSI :16 [ 1.966896] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 24209 usecs [ 1.967180] xen: registering gsi 17 triggering 0 polarity 1 [ 1.967256] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.967451] xen: registering gsi 18 triggering 0 polarity 1 [ 1.967478] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.991915] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23944 usecs [ 1.992169] xen: registering gsi 18 triggering 0 polarity 1 [ 1.992184] Already setup the GSI :18 [ 2.016873] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 24181 usecs [ 2.017152] xen: registering gsi 19 triggering 0 polarity 1 [ 2.017220] xen: --> pirq=19 -> irq=19 (gsi=19) [ 2.017440] xen: registering gsi 18 triggering 0 polarity 1 [ 2.017444] Already setup the GSI :18 [ 2.042093] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 24112 usecs [ 2.042771] PCI: CLS 64 bytes, default 64 [ 2.042917] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 2.043026] software IO TLB: mapped [mem 0x000000001b200000-0x000000001f200000] (64MB) [ 2.043277] kvm_intel: VMX not supported by CPU 0 [ 2.043383] kvm_amd: SVM not supported by CPU 0 [ 2.043491] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cb3604f57e, max_idle_ns: 440795281302 ns [ 2.043632] Unpacking initramfs... [ 2.043925] clocksource: Switched to clocksource tsc [ 2.062333] Initialise system trusted keyrings [ 2.063131] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 2.064227] NFS: Registering the id_resolver key type [ 2.064893] Key type id_resolver registered [ 2.065547] Key type id_legacy registered [ 2.066293] 9p: Installing v9fs 9p2000 file system support [ 2.087563] Key type asymmetric registered [ 2.088000] Asymmetric key parser 'x509' registered [ 2.088666] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.089203] io scheduler mq-deadline registered [ 2.089667] io scheduler kyber registered [ 2.091856] xen: registering gsi 53 triggering 0 polarity 1 [ 2.092051] xen: --> pirq=53 -> irq=53 (gsi=53) [ 2.094660] xen: registering gsi 54 triggering 0 polarity 1 [ 2.094833] xen: --> pirq=54 -> irq=54 (gsi=54) [ 2.097998] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 2.098849] ACPI: button: Power Button [PWRB] [ 2.099668] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 2.100708] ACPI: button: Power Button [PWRF] [ 2.103709] ACPI: \_PR_.P001: Found 2 idle states [ 2.104237] ACPI: \_PR_.P002: Found 2 idle states [ 2.106779] ACPI: \_PR_.P003: Found 2 idle states [ 2.107669] ACPI: \_PR_.P004: Found 2 idle states [ 2.108640] ACPI: \_PR_.P005: Found 2 idle states [ 2.109621] ACPI: \_PR_.P006: Found 2 idle states [ 2.112473] xen:xen_evtchn: Event-channel device installed [ 2.113922] xen_pciback: backend is vpci [ 2.117309] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.117972] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.119404] hpet_acpi_add: no address or irqs in _CRS [ 2.119612] Non-volatile memory driver v1.3 [ 2.124031] loop: module loaded [ 2.135729] ahci 0000:00:11.0: version 3.0 [ 2.135973] xen: registering gsi 22 triggering 0 polarity 1 [ 2.136069] xen: --> pirq=22 -> irq=22 (gsi=22) [ 2.136385] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 2.136546] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 2.136659] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 2.138542] scsi host0: ahci [ 2.139082] scsi host1: ahci [ 2.139646] scsi host2: ahci [ 2.140121] scsi host3: ahci [ 2.140296] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 2.140458] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 2.140604] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 2.140748] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 2.141565] tun: Universal TUN/TAP device driver, 1.6 [ 2.141871] e100: Intel(R) PRO/100 Network Driver [ 2.141977] e100: Copyright(c) 1999-2006 Intel Corporation [ 2.142103] sky2: driver version 1.30 [ 2.142269] xen_netfront: Initialising Xen virtual ethernet driver [ 2.142760] xen: registering gsi 16 triggering 0 polarity 1 [ 2.142780] Already setup the GSI :16 [ 2.142951] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 2.143162] xen: registering gsi 17 triggering 0 polarity 1 [ 2.143181] Already setup the GSI :17 [ 2.143181] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 2.143282] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 2.144149] xen: registering gsi 19 triggering 0 polarity 1 [ 2.144218] Already setup the GSI :19 [ 2.199777] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.199967] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.200109] usb usb1: Product: OHCI PCI host controller [ 2.200222] usb usb1: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.200356] usb usb1: SerialNumber: 0000:00:12.0 [ 2.200913] hub 1-0:1.0: USB hub found [ 2.201088] hub 1-0:1.0: 3 ports detected [ 2.201821] xen: registering gsi 16 triggering 0 polarity 1 [ 2.201836] Already setup the GSI :16 [ 2.201845] ehci-pci 0000:00:12.2: EHCI Host Controller [ 2.202235] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 2.202397] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 2.202569] ehci-pci 0000:00:12.2: debug port 1 [ 2.202812] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 2.210400] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 2.210781] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 2.210930] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.211072] usb usb2: Product: EHCI Host Controller [ 2.211177] usb usb2: Manufacturer: Linux 6.10.0-rc4+ ehci_hcd [ 2.211290] usb usb2: SerialNumber: 0000:00:12.2 [ 2.211848] hub 2-0:1.0: USB hub found [ 2.212011] hub 2-0:1.0: 6 ports detected [ 2.264668] hub 1-0:1.0: USB hub found [ 2.264861] hub 1-0:1.0: 3 ports detected [ 2.265363] ehci-pci 0000:00:13.2: EHCI Host Controller [ 2.265675] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 2.265825] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 2.265996] ehci-pci 0000:00:13.2: debug port 1 [ 2.266288] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 2.273377] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 2.273851] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 2.274042] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.274184] usb usb3: Product: EHCI Host Controller [ 2.274296] usb usb3: Manufacturer: Linux 6.10.0-rc4+ ehci_hcd [ 2.274431] usb usb3: SerialNumber: 0000:00:13.2 [ 2.274898] hub 3-0:1.0: USB hub found [ 2.275038] hub 3-0:1.0: 6 ports detected [ 2.275685] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 2.276010] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 2.276232] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 2.332807] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.332998] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.333140] usb usb4: Product: OHCI PCI host controller [ 2.333254] usb usb4: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.333394] usb usb4: SerialNumber: 0000:00:12.1 [ 2.333988] hub 4-0:1.0: USB hub found [ 2.334156] hub 4-0:1.0: 3 ports detected [ 2.334826] xen: registering gsi 18 triggering 0 polarity 1 [ 2.334841] Already setup the GSI :18 [ 2.335074] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 2.335398] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 2.335649] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 2.369676] Freeing initrd memory: 20192K [ 2.391746] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.391920] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.392060] usb usb5: Product: OHCI PCI host controller [ 2.392172] usb usb5: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.392294] usb usb5: SerialNumber: 0000:00:13.0 [ 2.393152] hub 5-0:1.0: USB hub found [ 2.393762] hub 5-0:1.0: 3 ports detected [ 2.396222] xen: registering gsi 18 triggering 0 polarity 1 [ 2.396261] Already setup the GSI :18 [ 2.396991] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 2.397918] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 2.398671] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 2.448423] ata4: SATA link down (SStatus 0 SControl 300) [ 2.448938] ata3: SATA link down (SStatus 0 SControl 300) [ 2.454498] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.454671] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.454812] usb usb6: Product: OHCI PCI host controller [ 2.454918] usb usb6: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.455060] usb usb6: SerialNumber: 0000:00:13.1 [ 2.455569] hub 6-0:1.0: USB hub found [ 2.455684] hub 6-0:1.0: 3 ports detected [ 2.456245] xen: registering gsi 18 triggering 0 polarity 1 [ 2.456258] Already setup the GSI :18 [ 2.456465] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 2.456835] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 2.457053] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 2.512489] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.512649] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.512787] usb usb7: Product: OHCI PCI host controller [ 2.512890] usb usb7: Manufacturer: Linux 6.10.0-rc4+ ohci_hcd [ 2.512995] usb usb7: SerialNumber: 0000:00:14.5 [ 2.513348] hub 7-0:1.0: USB hub found [ 2.513469] hub 7-0:1.0: 2 ports detected [ 2.513843] usbcore: registered new interface driver usblp [ 2.513971] usbcore: registered new interface driver usb-storage [ 2.514114] i8042: PNP: No PS/2 controller found. [ 2.514214] i8042: Probing ports directly. [ 2.517303] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.517422] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.517791] rtc_cmos 00:02: RTC can wake from S4 [ 2.518300] rtc_cmos 00:02: registered as rtc0 [ 2.518460] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 2.518652] device-mapper: uevent: version 1.0.3 [ 2.518855] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 2.519006] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 2.519158] hid: raw HID events driver (C) Jiri Kosina [ 2.519478] usbcore: registered new interface driver usbhid [ 2.519582] usbhid: USB HID core driver [ 2.520080] Initializing XFRM netlink socket [ 2.520216] NET: Registered PF_INET6 protocol family [ 2.520868] Segment Routing with IPv6 [ 2.520984] In-situ OAM (IOAM) with IPv6 [ 2.521120] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.521417] NET: Registered PF_PACKET protocol family [ 2.521545] 9pnet: Installing 9P2000 support [ 2.521661] Key type dns_resolver registered [ 2.521774] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 2.522479] IPI shorthand broadcast: enabled [ 2.526864] sched_clock: Marking stable (2500003979, 26316347)->(2573338427, -47018101) [ 2.527395] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.527742] registered taskstats version 1 [ 2.527841] Loading compiled-in X.509 certificates [ 2.529882] PM: Magic number: 12:429:749 [ 2.531553] tty ttyS0: hash matches [ 2.531691] printk: legacy console [netcon0] enabled [ 2.531793] netconsole: network logging started [ 2.531998] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.541821] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.542232] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.542397] ALSA device list: [ 2.542495] No soundcards found. [ 2.543242] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 2.609452] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.609595] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.610864] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 2.611278] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA [ 2.612732] ata2.00: ATAPI: ATAPI iHAS124 E, 4L07, max UDMA/100 [ 2.613624] ata2.00: configured for UDMA/100 [ 2.613735] ata1.00: configured for UDMA/133 [ 2.613983] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 2.614567] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.614631] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.614866] sd 0:0:0:0: [sda] Write Protect is off [ 2.614988] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.615012] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.615196] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 2.615551] scsi 1:0:0:0: CD-ROM ATAPI iHAS124 E 4L07 PQ: 0 ANSI: 5 [ 2.639733] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.639885] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.640260] sda: sda1 sda2 < sda5 > [ 2.640650] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.653953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.654078] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.655900] Freeing unused kernel image (initmem) memory: 2680K [ 2.656035] Write protecting the kernel read-only data: 24576k [ 2.667849] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.769351] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.775854] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.775975] Run /init as init process [ 2.776071] with arguments: [ 2.776073] /init [ 2.776074] placeholder [ 2.776075] with environment: [ 2.776076] HOME=/ [ 2.776078] TERM=linux [ 2.931422] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.931581] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.931693] usb 6-2: Product: Hermon USB hidmouse Device [ 2.931797] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.937981] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.938503] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.941907] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.993707] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 3.025989] e1000e: Intel(R) PRO/1000 Network Driver [ 3.026113] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.026403] xen: registering gsi 48 triggering 0 polarity 1 [ 3.026445] xen: --> pirq=48 -> irq=48 (gsi=48) [ 3.026719] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 3.070143] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 3.114162] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f6 [ 3.114313] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 3.114513] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 3.114716] xen: registering gsi 47 triggering 0 polarity 1 [ 3.114742] xen: --> pirq=47 -> irq=47 (gsi=47) [ 3.114924] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 3.161338] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 3.208368] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f7 [ 3.208515] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 3.208703] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 3.210679] e1000e 0000:01:00.0 enx0cc47a0a48f6: renamed from eth0 [ 3.210951] e1000e 0000:02:00.0 enx0cc47a0a48f7: renamed from eth1 [ 3.334356] random: crng init done [ 3.983995] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.989256] EXT4-fs (dm-0): mounted filesystem 5617cafe-6799-45c1-bd7b-e809989eda3f ro with ordered data mode. Quota mode: none. [ 8.310941] EXT4-fs (dm-0): re-mounted 5617cafe-6799-45c1-bd7b-e809989eda3f r/w. Quota mode: none. [ 9.780125] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 9.798377] EXT4-fs (sda1): mounted filesystem 2b78bb18-4808-46c3-a218-e9343ca6a1a7 r/w with ordered data mode. Quota mode: none. [ 9.874163] Adding 1949692k swap on /dev/mapper/rimava1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 11.435299] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 11.435462] xenbr0: port 1(enx0cc47a0a48f6) entered disabled state [ 11.435590] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered allmulticast mode [ 11.435745] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered promiscuous mode [ 14.491388] e1000e 0000:01:00.0 enx0cc47a0a48f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 14.491940] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 14.492049] xenbr0: port 1(enx0cc47a0a48f6) entered forwarding state