[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc4+ (osstest@himrod1) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Jun 23 16:58:40 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6080K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000513] Console: colour dummy device 80x30 [ 0.000531] printk: legacy console [hvc0] enabled [ 0.299527] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309925] CPU: Testing write buffer coherency: ok [ 0.314866] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.324420] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330852] pid_max: default: 32768 minimum: 301 [ 0.335622] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342900] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.351316] /cpus/cpu@0 missing clock-frequency property [ 0.356104] /cpus/cpu@1 missing clock-frequency property [ 0.361523] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.368209] xen:grant_table: Grant tables using version 1 layout [ 0.373355] Grant table initialized [ 0.376904] xen:events: Using FIFO-based ABI [ 0.381206] Xen: initializing cpu0 [ 0.384730] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392528] rcu: Hierarchical SRCU implementation. [ 0.396126] rcu: Max phase no-delay instances is 1000. [ 0.404344] EFI services will not be available. [ 0.407663] smp: Bringing up secondary CPUs ... [ 0.482011] Xen: initializing cpu1 [ 0.482171] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.482195] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.501161] smp: Brought up 1 node, 2 CPUs [ 0.504824] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.511111] CPU: All CPU(s) started in SVC mode. [ 0.517051] devtmpfs: initialized [ 0.529626] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.536181] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545852] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553791] pinctrl core: initialized pinctrl subsystem [ 0.560381] DMI not present or invalid. [ 0.563900] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.570516] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579884] thermal_sys: Registered thermal governor 'step_wise' [ 0.580043] software IO TLB: area num 2. [ 0.588715] software IO TLB: only able to allocate 8 MB [ 0.595788] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600994] No ATAGs? [ 0.603295] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.612052] Serial: AMBA PL011 UART driver [ 0.658666] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.687153] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.710798] xen:balloon: Initialising balloon driver [ 0.717241] iommu: Default domain type: Translated [ 0.720654] iommu: DMA domain TLB invalidation policy: strict mode [ 0.732423] SCSI subsystem initialized [ 0.734972] libata version 3.00 loaded. [ 0.735202] usbcore: registered new interface driver usbfs [ 0.740408] usbcore: registered new interface driver hub [ 0.745775] usbcore: registered new device driver usb [ 0.752441] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.756036] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.762293] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.767356] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.772289] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.778322] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.784106] pps_core: LinuxPPS API ver. 1 registered [ 0.788495] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.797739] PTP clock support registered [ 0.801946] EDAC MC: Ver: 3.0.0 [ 0.805255] scmi_core: SCMI protocol bus registered [ 0.811887] vgaarb: loaded [ 0.820373] clocksource: Switched to clocksource arch_sys_counter [ 0.834706] NET: Registered PF_INET protocol family [ 0.838349] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.846298] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.853951] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.861754] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.869596] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.876885] TCP: Hash tables configured (established 4096 bind 4096) [ 0.883239] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.889807] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.896917] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.908658] RPC: Registered named UNIX socket transport module. [ 0.913219] RPC: Registered udp transport module. [ 0.917975] RPC: Registered tcp transport module. [ 0.922759] RPC: Registered tcp-with-tls transport module. [ 0.928303] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.934829] PCI: CLS 0 bytes, default 64 [ 0.940273] Initialise system trusted keyrings [ 0.943599] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.950127] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.956000] Trying to unpack rootfs image as initramfs... [ 0.980801] NFS: Registering the id_resolver key type [ 0.984516] Key type id_resolver registered [ 0.988745] Key type id_legacy registered [ 0.992867] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.999621] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.015290] Key type asymmetric registered [ 1.018028] Asymmetric key parser 'x509' registered [ 1.023086] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.030481] io scheduler mq-deadline registered [ 1.035040] io scheduler kyber registered [ 1.039161] io scheduler bfq registered [ 1.182844] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.189080] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.233689] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.239899] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.298574] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.304826] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.335487] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.341767] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.354390] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.390950] xen:xen_evtchn: Event-channel device installed [ 1.475836] Freeing initrd memory: 11856K [ 1.519214] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.530676] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.538845] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.547793] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.556777] SuperH (H)SCI(F) driver initialized [ 1.561095] STMicroelectronics ASC driver initialized [ 1.565942] STM32 USART driver initialized [ 1.580409] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.589046] random: crng init done [ 1.596830] brd: module loaded [ 1.602837] loop: module loaded [ 1.625217] Invalid max_queues (4), will use default max: 2. [ 1.644008] tun: Universal TUN/TAP device driver, 1.6 [ 1.647862] CAN device driver interface [ 1.653053] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.664230] xen_netfront: Initialising Xen virtual ethernet driver [ 1.669099] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.674711] usbcore: registered new interface driver pegasus [ 1.680441] usbcore: registered new interface driver asix [ 1.685895] usbcore: registered new interface driver ax88179_178a [ 1.692067] usbcore: registered new interface driver cdc_ether [ 1.697964] usbcore: registered new interface driver smsc75xx [ 1.703789] usbcore: registered new interface driver smsc95xx [ 1.709591] usbcore: registered new interface driver net1080 [ 1.715335] usbcore: registered new interface driver cdc_subset [ 1.721319] usbcore: registered new interface driver zaurus [ 1.726955] usbcore: registered new interface driver cdc_ncm [ 1.736343] usbcore: registered new interface driver usb-storage [ 1.746870] i2c_dev: i2c /dev entries driver [ 1.765282] device-mapper: uevent: version 1.0.3 [ 1.768710] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.778321] cpu cpu0: OPP table can't be empty [ 1.783070] failed to register cpuidle driver [ 1.786411] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.794769] sdhci: Secure Digital Host Controller Interface driver [ 1.799776] sdhci: Copyright(c) Pierre Ossman [ 1.807866] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.815640] ledtrig-cpu: registered to indicate activity on CPUs [ 1.821137] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.827769] usbcore: registered new interface driver usbhid [ 1.832475] usbhid: USB HID core driver [ 1.843551] NET: Registered PF_INET6 protocol family [ 1.848064] Segment Routing with IPv6 [ 1.850956] In-situ OAM (IOAM) with IPv6 [ 1.854934] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.861470] NET: Registered PF_PACKET protocol family [ 1.865991] can: controller area network core [ 1.870483] NET: Registered PF_CAN protocol family [ 1.875268] can: raw protocol [ 1.878309] can: broadcast manager protocol [ 1.882591] can: netlink gateway - max_hops=1 [ 1.887301] Key type dns_resolver registered [ 1.892039] ThumbEE CPU extension supported. [ 1.895671] Registering SWP/SWPB emulation handler [ 1.910231] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.917155] Loading compiled-in X.509 certificates [ 1.960031] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.963711] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.970954] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.978478] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.020281] s5m-rtc s5m-rtc: registered as rtc0 [ 2.029177] s5m-rtc s5m-rtc: setting system clock to 2024-06-23T21:32:17 UTC (1719178337) [ 2.040243] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.044918] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.049217] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.056019] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.062058] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.068155] clk: Not disabling unused clocks [ 2.071746] PM: genpd: Disabling unused power domains [ 2.080355] Freeing unused kernel image (initmem) memory: 2048K [ 2.086636] Run /init as init process [ 2.088915] with arguments: [ 2.088922] /init [ 2.088928] with environment: [ 2.088934] HOME=/ [ 2.088939] TERM=linux [ 3.342331] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.454607] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.469672] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.475811] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.481522] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.504045] Synopsys Designware Multimedia Card Interface Driver [ 3.540870] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.546471] exynos-ohci 12120000.usb: USB Host Controller [ 3.551989] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.560909] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.568195] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.581489] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.587198] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.640201] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.649114] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.659022] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.682451] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.690011] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.695753] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.704940] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.711855] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.781214] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.786312] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.791887] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.801721] mmc_host mmc0: card is polling. [ 3.806340] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.812138] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.817610] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.827787] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.838494] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.873995] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.878528] scsi host0: ahci-dwc [ 3.882808] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.885735] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 3.905411] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.914899] hub 1-0:1.0: USB hub found [ 3.917511] hub 1-0:1.0: 3 ports detected [ 3.922956] hub 2-0:1.0: USB hub found [ 3.925590] hub 2-0:1.0: 3 ports detected [ 3.938642] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.943412] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.007629] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.016538] mmc0: new DDR MMC card at address 0001 [ 4.021738] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.027857] mmcblk0: p1 p2 p3 p4 [ 4.033900] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.038918] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.044239] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.075522] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.084100] mmc1: new high speed SDHC card at address aaaa [ 4.090064] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.410399] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.416157] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.422020] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.429705] ata1.00: configured for UDMA/133 [ 4.433455] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.442854] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.448986] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.454556] sd 0:0:0:0: [sda] Write Protect is off [ 4.459138] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.459221] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.468390] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.491515] sda: sda1 sda2 < sda5 > [ 4.494227] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.995885] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 5.008219] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.012412] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.025089] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 5.033665] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 5.039429] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.044812] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.052592] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.060617] hub 3-0:1.0: USB hub found [ 5.063209] hub 3-0:1.0: 1 port detected [ 5.068332] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.082498] hub 4-0:1.0: USB hub found [ 5.085197] hub 4-0:1.0: 1 port detected [ 5.360440] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.529236] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.666705] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 5.774939] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 5.883247] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 5.991556] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 6.147351] I/O error, dev mmcblk1, sector 7743712 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0 [ 6.431290] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 6.600843] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 6.715179] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.822936] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.930695] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7.038408] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7.046023] Buffer I/O error on dev mmcblk1, logical block 967954, async page read [ 10.596912] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 10.977350] EXT4-fs (dm-0): mounted filesystem e796c825-b043-4466-8fc2-68b9788da7a1 ro with ordered data mode. Quota mode: disabled. [ 15.093620] s5p-secss 10830000.sss: s5p-sss driver registered [ 15.116678] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.232954] mc: Linux media interface: v0.10 [ 15.388719] videodev: Linux video capture interface: v2.00 [ 15.664303] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 15.673816] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.737290] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.754776] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.762185] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.782719] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 15.788053] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 15.797078] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.804287] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 15.830616] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 15.844908] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 15.874958] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 15.989661] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.000755] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 16.060451] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 16.065910] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 16.084557] usb3503 usb-hub: switched to HUB mode [ 16.087902] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.192701] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 16.301169] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 16.412100] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 16.440633] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.520941] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 16.638956] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.646729] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.655367] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.667580] hub 1-3:1.0: USB hub found [ 16.670195] hub 1-3:1.0: 3 ports detected [ 16.670638] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.683185] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.691897] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.914128] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.990428] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.080095] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.144927] hub 1-3.2:1.0: USB hub found [ 17.148365] hub 1-3.2:1.0: 4 ports detected [ 17.195512] usbcore: registered new device driver onboard-usb-dev [ 17.200884] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.321888] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.333208] hub 1-3.2:1.0: USB hub found [ 17.336162] hub 1-3.2:1.0: 4 ports detected [ 17.350031] hub 1-3.2:1.0: USB hub found [ 17.353010] hub 1-3.2:1.0: 4 ports detected [ 17.429630] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 17.437266] Buffer I/O error on dev mmcblk1, logical block 967954, async page read [ 17.670413] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.854384] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.947231] EXT4-fs (dm-0): re-mounted e796c825-b043-4466-8fc2-68b9788da7a1 r/w. Quota mode: disabled. [ 18.594632] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.598249] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.598819] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 1a:29:c0:21:7d:64 [ 19.659508] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 19.711428] EXT4-fs (sda1): mounted filesystem 59d316ed-b0e6-46e5-b667-053f04789c68 r/w with ordered data mode. Quota mode: disabled. [ 19.811757] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 21.720940] xenbr0: port 1(eth0) entered blocking state [ 21.724808] xenbr0: port 1(eth0) entered disabled state [ 21.730119] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 21.735997] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 21.746792] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.928673] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 23.934714] xenbr0: port 1(eth0) entered blocking state [ 23.939937] xenbr0: port 1(eth0) entered forwarding state