[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc4+ (osstest@himrod1) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Jun 23 16:58:40 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6080K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000518] Console: colour dummy device 80x30 [ 0.000536] printk: legacy console [hvc0] enabled [ 0.299532] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309930] CPU: Testing write buffer coherency: ok [ 0.314872] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.324425] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330839] pid_max: default: 32768 minimum: 301 [ 0.335626] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342907] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.351300] /cpus/cpu@0 missing clock-frequency property [ 0.356109] /cpus/cpu@1 missing clock-frequency property [ 0.361503] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.368213] xen:grant_table: Grant tables using version 1 layout [ 0.373360] Grant table initialized [ 0.376915] xen:events: Using FIFO-based ABI [ 0.381212] Xen: initializing cpu0 [ 0.384750] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392505] rcu: Hierarchical SRCU implementation. [ 0.396130] rcu: Max phase no-delay instances is 1000. [ 0.404327] EFI services will not be available. [ 0.407644] smp: Bringing up secondary CPUs ... [ 0.483047] Xen: initializing cpu1 [ 0.483215] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.483238] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.502153] smp: Brought up 1 node, 2 CPUs [ 0.505810] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.512097] CPU: All CPU(s) started in SVC mode. [ 0.518012] devtmpfs: initialized [ 0.530605] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.537158] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.546830] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.554713] pinctrl core: initialized pinctrl subsystem [ 0.561379] DMI not present or invalid. [ 0.564875] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.571508] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.580886] thermal_sys: Registered thermal governor 'step_wise' [ 0.581044] software IO TLB: area num 2. [ 0.589719] software IO TLB: only able to allocate 8 MB [ 0.596790] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.602009] No ATAGs? [ 0.604299] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.613043] Serial: AMBA PL011 UART driver [ 0.659764] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.688270] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.711501] xen:balloon: Initialising balloon driver [ 0.717995] iommu: Default domain type: Translated [ 0.721412] iommu: DMA domain TLB invalidation policy: strict mode [ 0.730192] SCSI subsystem initialized [ 0.732735] libata version 3.00 loaded. [ 0.732969] usbcore: registered new interface driver usbfs [ 0.738194] usbcore: registered new interface driver hub [ 0.743543] usbcore: registered new device driver usb [ 0.750224] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.753819] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.760083] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.765139] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.770083] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.776107] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.781920] pps_core: LinuxPPS API ver. 1 registered [ 0.786279] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.795508] PTP clock support registered [ 0.799723] EDAC MC: Ver: 3.0.0 [ 0.803005] scmi_core: SCMI protocol bus registered [ 0.817921] vgaarb: loaded [ 0.821739] clocksource: Switched to clocksource arch_sys_counter [ 0.836070] NET: Registered PF_INET protocol family [ 0.839710] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.847639] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.855310] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.863113] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.870948] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.878238] TCP: Hash tables configured (established 4096 bind 4096) [ 0.884599] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.891148] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.898272] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.909927] RPC: Registered named UNIX socket transport module. [ 0.914489] RPC: Registered udp transport module. [ 0.919247] RPC: Registered tcp transport module. [ 0.924033] RPC: Registered tcp-with-tls transport module. [ 0.929576] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.936106] PCI: CLS 0 bytes, default 64 [ 0.941574] Initialise system trusted keyrings [ 0.944991] Trying to unpack rootfs image as initramfs... [ 0.971986] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.977387] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.992082] NFS: Registering the id_resolver key type [ 0.995788] Key type id_resolver registered [ 1.000016] Key type id_legacy registered [ 1.004160] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.010873] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.052772] Key type asymmetric registered [ 1.055531] Asymmetric key parser 'x509' registered [ 1.060515] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.067953] io scheduler mq-deadline registered [ 1.072534] io scheduler kyber registered [ 1.076638] io scheduler bfq registered [ 1.199525] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.205767] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.253474] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.259680] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.304109] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.310310] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.363078] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.369304] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.381657] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.454578] xen:xen_evtchn: Event-channel device installed [ 1.585068] Freeing initrd memory: 11856K [ 1.631500] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.642578] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.650778] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.659680] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.668692] SuperH (H)SCI(F) driver initialized [ 1.672992] STMicroelectronics ASC driver initialized [ 1.677926] STM32 USART driver initialized [ 1.683459] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.684054] random: crng init done [ 1.698979] brd: module loaded [ 1.705098] loop: module loaded [ 1.722670] Invalid max_queues (4), will use default max: 2. [ 1.741500] tun: Universal TUN/TAP device driver, 1.6 [ 1.745384] CAN device driver interface [ 1.750485] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.761785] xen_netfront: Initialising Xen virtual ethernet driver [ 1.766643] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.772288] usbcore: registered new interface driver pegasus [ 1.777986] usbcore: registered new interface driver asix [ 1.783484] usbcore: registered new interface driver ax88179_178a [ 1.789617] usbcore: registered new interface driver cdc_ether [ 1.795533] usbcore: registered new interface driver smsc75xx [ 1.801340] usbcore: registered new interface driver smsc95xx [ 1.807175] usbcore: registered new interface driver net1080 [ 1.812894] usbcore: registered new interface driver cdc_subset [ 1.818868] usbcore: registered new interface driver zaurus [ 1.824530] usbcore: registered new interface driver cdc_ncm [ 1.833942] usbcore: registered new interface driver usb-storage [ 1.844596] i2c_dev: i2c /dev entries driver [ 1.863257] device-mapper: uevent: version 1.0.3 [ 1.866684] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.876299] cpu cpu0: OPP table can't be empty [ 1.881021] failed to register cpuidle driver [ 1.884419] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.892778] sdhci: Secure Digital Host Controller Interface driver [ 1.897753] sdhci: Copyright(c) Pierre Ossman [ 1.905819] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.913613] ledtrig-cpu: registered to indicate activity on CPUs [ 1.919009] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.925738] usbcore: registered new interface driver usbhid [ 1.930389] usbhid: USB HID core driver [ 1.941316] NET: Registered PF_INET6 protocol family [ 1.945935] Segment Routing with IPv6 [ 1.948664] In-situ OAM (IOAM) with IPv6 [ 1.952742] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.959086] NET: Registered PF_PACKET protocol family [ 1.963784] can: controller area network core [ 1.968199] NET: Registered PF_CAN protocol family [ 1.973046] can: raw protocol [ 1.976068] can: broadcast manager protocol [ 1.980324] can: netlink gateway - max_hops=1 [ 1.985079] Key type dns_resolver registered [ 1.989752] ThumbEE CPU extension supported. [ 1.993472] Registering SWP/SWPB emulation handler [ 2.007970] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.014885] Loading compiled-in X.509 certificates [ 2.058541] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.062207] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.069173] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.076943] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.126296] s5m-rtc s5m-rtc: registered as rtc0 [ 2.135218] s5m-rtc s5m-rtc: setting system clock to 2000-01-02T00:00:23 UTC (946771223) [ 2.146237] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.150840] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.155274] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.162019] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.167846] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.174034] clk: Not disabling unused clocks [ 2.177520] PM: genpd: Disabling unused power domains [ 2.186122] Freeing unused kernel image (initmem) memory: 2048K [ 2.192487] Run /init as init process [ 2.194772] with arguments: [ 2.194779] /init [ 2.194784] with environment: [ 2.194789] HOME=/ [ 2.194795] TERM=linux [ 3.459294] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.549561] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.561917] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.631687] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.644472] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.650068] exynos-ohci 12120000.usb: USB Host Controller [ 3.655602] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 3.668600] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.674276] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.679797] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 3.687625] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.695298] Synopsys Designware Multimedia Card Interface Driver [ 3.714810] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.762917] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.768975] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.785322] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.791758] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.798496] hub 1-0:1.0: USB hub found [ 3.799019] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.808612] hub 1-0:1.0: 3 ports detected [ 3.808621] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.821479] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.826739] hub 2-0:1.0: USB hub found [ 3.828351] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.841922] hub 2-0:1.0: 3 ports detected [ 3.884950] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.925464] scsi host0: ahci-dwc [ 3.932465] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 126 lpm-pol 0 [ 3.940915] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.984372] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.989469] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.995035] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 4.005055] mmc_host mmc0: card is polling. [ 4.009150] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.015284] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.020784] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 128,32 bit host data width,128 deep fifo [ 4.036610] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.057396] s2mps11-clk s5m8767-clk: DMA mask not set [ 4.061674] VDD_ALIVE_1.0V: Bringing 1000000uV into 1100000-1100000uV [ 4.097929] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.101841] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.115617] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.196318] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.205653] mmc0: new DDR MMC card at address 0001 [ 4.210267] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.216403] mmcblk0: p1 p2 p3 p4 [ 4.223254] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.228584] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.241147] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.337917] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.353123] mmc1: new high speed SDHC card at address aaaa [ 4.366707] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.451858] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.459328] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.464706] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.475345] ata1.00: configured for UDMA/133 [ 4.487918] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.502042] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.508165] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.514101] sd 0:0:0:0: [sda] Write Protect is off [ 4.518322] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.518632] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.527825] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.546730] sda: sda1 sda2 < sda5 > [ 4.552964] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.762662] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.770940] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.775251] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.784111] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.792629] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.798542] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.803942] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.811648] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.819273] hub 3-0:1.0: USB hub found [ 4.822133] hub 3-0:1.0: 1 port detected [ 4.826876] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.835234] hub 4-0:1.0: USB hub found [ 4.838075] hub 4-0:1.0: 1 port detected [ 5.181782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.351005] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.495980] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 5.604331] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 5.712704] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 5.821005] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 6.197734] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 6.340595] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 6.454999] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.562761] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.670479] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.778236] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.785856] Buffer I/O error on dev mmcblk1, logical block 967954, async page read [ 11.308820] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.665905] EXT4-fs (dm-0): mounted filesystem 51a24ed0-37c6-4696-809b-7445c386eecb ro with ordered data mode. Quota mode: disabled. [ 15.358636] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 15.365114] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 15.828873] s5p-secss 10830000.sss: s5p-sss driver registered [ 15.834231] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.899131] mc: Linux media interface: v0.10 [ 15.953294] videodev: Linux video capture interface: v2.00 [ 16.078791] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 16.094872] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 16.199694] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.227887] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.235326] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.263794] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 16.288390] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 16.459490] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 16.465475] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 16.471647] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 16.477752] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 16.502319] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.681854] usb3503 usb-hub: switched to HUB mode [ 16.685575] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.707406] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.844963] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 16.954237] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 16.991923] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 17.063132] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 17.171839] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 0 [ 17.192560] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 17.414589] hub 2-3:1.0: USB hub found [ 17.420761] hub 2-3:1.0: 3 ports detected [ 17.463682] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.471397] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.480115] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.490951] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.499691] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.508416] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.631802] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 17.751801] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.800982] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.905036] hub 2-3.2:1.0: USB hub found [ 17.908066] hub 2-3.2:1.0: 4 ports detected [ 17.912403] I/O error, dev mmcblk1, sector 7744000 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 17.986074] usbcore: registered new device driver onboard-usb-dev [ 18.021488] I/O error, dev mmcblk1, sector 7744001 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 18.122707] hub 2-3.2:1.0: USB hub found [ 18.125761] hub 2-3.2:1.0: 4 ports detected [ 18.129868] I/O error, dev mmcblk1, sector 7744002 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 18.146526] hub 2-3.2:1.0: USB hub found [ 18.149474] hub 2-3.2:1.0: 4 ports detected [ 18.239216] I/O error, dev mmcblk1, sector 7744003 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 18.347432] I/O error, dev mmcblk1, sector 7744004 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 18.455628] I/O error, dev mmcblk1, sector 7744005 op 0x0:(READ) flags 0x80700 phys_seg 14 prio class 0 [ 18.471782] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 18.624966] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 19.313711] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 19.328206] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 19.338098] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 12:da:bf:ab:ca:52 [ 20.720116] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 20.871533] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 21.681016] Buffer I/O error on dev mmcblk1, logical block 968000, async page read [ 22.102703] EXT4-fs (dm-0): re-mounted 51a24ed0-37c6-4696-809b-7445c386eecb r/w. Quota mode: disabled. [ 23.481729] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 23.533559] EXT4-fs (sda1): mounted filesystem 4d7302ca-8918-41eb-970f-05d4e8662a3f r/w with ordered data mode. Quota mode: disabled. [ 23.645045] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 25.470897] xenbr0: port 1(eth0) entered blocking state [ 25.474814] xenbr0: port 1(eth0) entered disabled state [ 25.480091] asix 2-3.2.4:1.0 eth0: entered allmulticast mode [ 25.485979] asix 2-3.2.4:1.0 eth0: entered promiscuous mode [ 25.496958] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 27.669465] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 27.675542] xenbr0: port 1(eth0) entered blocking state [ 27.680706] xenbr0: port 1(eth0) entered forwarding state