[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc4+ (osstest@himrod1) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Jun 23 16:58:40 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6080K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000511] Console: colour dummy device 80x30 [ 0.000529] printk: legacy console [hvc0] enabled [ 0.299002] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309401] CPU: Testing write buffer coherency: ok [ 0.314342] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.323897] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330309] pid_max: default: 32768 minimum: 301 [ 0.335097] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342377] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350773] /cpus/cpu@0 missing clock-frequency property [ 0.355580] /cpus/cpu@1 missing clock-frequency property [ 0.360976] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367681] xen:grant_table: Grant tables using version 1 layout [ 0.372829] Grant table initialized [ 0.376385] xen:events: Using FIFO-based ABI [ 0.380683] Xen: initializing cpu0 [ 0.384207] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392006] rcu: Hierarchical SRCU implementation. [ 0.395601] rcu: Max phase no-delay instances is 1000. [ 0.403830] EFI services will not be available. [ 0.407151] smp: Bringing up secondary CPUs ... [ 0.481417] Xen: initializing cpu1 [ 0.481580] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481604] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500572] smp: Brought up 1 node, 2 CPUs [ 0.504230] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510518] CPU: All CPU(s) started in SVC mode. [ 0.516441] devtmpfs: initialized [ 0.529057] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535615] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545285] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553179] pinctrl core: initialized pinctrl subsystem [ 0.559811] DMI not present or invalid. [ 0.563323] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569932] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579286] thermal_sys: Registered thermal governor 'step_wise' [ 0.579445] software IO TLB: area num 2. [ 0.588116] software IO TLB: only able to allocate 8 MB [ 0.595186] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600392] No ATAGs? [ 0.602692] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611452] Serial: AMBA PL011 UART driver [ 0.658118] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686603] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.706502] xen:balloon: Initialising balloon driver [ 0.712940] iommu: Default domain type: Translated [ 0.716352] iommu: DMA domain TLB invalidation policy: strict mode [ 0.725532] SCSI subsystem initialized [ 0.728133] libata version 3.00 loaded. [ 0.728349] usbcore: registered new interface driver usbfs [ 0.733531] usbcore: registered new interface driver hub [ 0.738891] usbcore: registered new device driver usb [ 0.745540] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.749132] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.755390] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.760456] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.765378] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.771419] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.777185] pps_core: LinuxPPS API ver. 1 registered [ 0.781591] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.790820] PTP clock support registered [ 0.795035] EDAC MC: Ver: 3.0.0 [ 0.798401] scmi_core: SCMI protocol bus registered [ 0.804971] vgaarb: loaded [ 0.806991] clocksource: Switched to clocksource arch_sys_counter [ 0.820365] NET: Registered PF_INET protocol family [ 0.824005] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.831926] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.839604] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.847415] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.855235] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.862532] TCP: Hash tables configured (established 4096 bind 4096) [ 0.868892] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.875447] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.882577] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.888677] RPC: Registered named UNIX socket transport module. [ 0.894180] RPC: Registered udp transport module. [ 0.898968] RPC: Registered tcp transport module. [ 0.903727] RPC: Registered tcp-with-tls transport module. [ 0.909297] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.915799] PCI: CLS 0 bytes, default 64 [ 0.921235] Initialise system trusted keyrings [ 0.924483] Trying to unpack rootfs image as initramfs... [ 0.957615] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.962986] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.007184] NFS: Registering the id_resolver key type [ 1.010900] Key type id_resolver registered [ 1.015119] Key type id_legacy registered [ 1.019246] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.025976] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.057336] Key type asymmetric registered [ 1.060066] Asymmetric key parser 'x509' registered [ 1.065070] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.072501] io scheduler mq-deadline registered [ 1.077102] io scheduler kyber registered [ 1.081177] io scheduler bfq registered [ 1.209131] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.215335] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.269649] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.275862] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.327671] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.333876] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.377583] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.383787] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.396103] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.448408] xen:xen_evtchn: Event-channel device installed [ 1.567966] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.593194] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.617880] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.645377] Freeing initrd memory: 11856K [ 1.648669] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.658269] SuperH (H)SCI(F) driver initialized [ 1.662001] STMicroelectronics ASC driver initialized [ 1.666854] STM32 USART driver initialized [ 1.672450] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.673028] random: crng init done [ 1.688039] brd: module loaded [ 1.693969] loop: module loaded [ 1.711456] Invalid max_queues (4), will use default max: 2. [ 1.730415] tun: Universal TUN/TAP device driver, 1.6 [ 1.734264] CAN device driver interface [ 1.739496] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.750708] xen_netfront: Initialising Xen virtual ethernet driver [ 1.755556] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.761189] usbcore: registered new interface driver pegasus [ 1.766902] usbcore: registered new interface driver asix [ 1.772390] usbcore: registered new interface driver ax88179_178a [ 1.778570] usbcore: registered new interface driver cdc_ether [ 1.784439] usbcore: registered new interface driver smsc75xx [ 1.790265] usbcore: registered new interface driver smsc95xx [ 1.796065] usbcore: registered new interface driver net1080 [ 1.801805] usbcore: registered new interface driver cdc_subset [ 1.807797] usbcore: registered new interface driver zaurus [ 1.813430] usbcore: registered new interface driver cdc_ncm [ 1.822823] usbcore: registered new interface driver usb-storage [ 1.833397] i2c_dev: i2c /dev entries driver [ 1.852083] device-mapper: uevent: version 1.0.3 [ 1.855500] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.865130] cpu cpu0: OPP table can't be empty [ 1.869876] failed to register cpuidle driver [ 1.873208] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.881554] sdhci: Secure Digital Host Controller Interface driver [ 1.886572] sdhci: Copyright(c) Pierre Ossman [ 1.894640] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.902401] ledtrig-cpu: registered to indicate activity on CPUs [ 1.907853] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.914475] usbcore: registered new interface driver usbhid [ 1.919223] usbhid: USB HID core driver [ 1.930124] NET: Registered PF_INET6 protocol family [ 1.934632] Segment Routing with IPv6 [ 1.937529] In-situ OAM (IOAM) with IPv6 [ 1.941501] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.947928] NET: Registered PF_PACKET protocol family [ 1.952562] can: controller area network core [ 1.957043] NET: Registered PF_CAN protocol family [ 1.961840] can: raw protocol [ 1.964879] can: broadcast manager protocol [ 1.969169] can: netlink gateway - max_hops=1 [ 1.973876] Key type dns_resolver registered [ 1.978566] ThumbEE CPU extension supported. [ 1.982243] Registering SWP/SWPB emulation handler [ 1.996733] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.003645] Loading compiled-in X.509 certificates [ 2.046775] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.050453] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.057615] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.065145] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.106822] s5m-rtc s5m-rtc: registered as rtc0 [ 2.115727] s5m-rtc s5m-rtc: setting system clock to 2024-06-23T20:53:08 UTC (1719175988) [ 2.126794] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.131479] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.135771] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.142632] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.148566] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.154708] clk: Not disabling unused clocks [ 2.158256] PM: genpd: Disabling unused power domains [ 2.166683] Freeing unused kernel image (initmem) memory: 2048K [ 2.173098] Run /init as init process [ 2.175391] with arguments: [ 2.175397] /init [ 2.175404] with environment: [ 2.175409] HOME=/ [ 2.175414] TERM=linux [ 3.435402] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.574232] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.588776] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.595846] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.609511] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.615112] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.691359] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.703548] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.740272] Synopsys Designware Multimedia Card Interface Driver [ 3.740382] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.798366] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.804599] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.812067] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.826180] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.832362] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.835134] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.844004] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.852818] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.859650] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.870107] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.875350] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.880922] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.880939] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.896518] mmc_host mmc0: card is polling. [ 3.902714] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.922168] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.929999] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.935766] exynos-ohci 12120000.usb: USB Host Controller [ 3.942410] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.959511] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.964641] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.970147] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 129,32 bit host data width,128 deep fifo [ 3.988112] hub 1-0:1.0: USB hub found [ 3.990548] hub 1-0:1.0: 3 ports detected [ 3.994694] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.005398] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 4.012339] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 4.044911] scsi host0: ahci-dwc [ 4.063078] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 127 lpm-pol 0 [ 4.097225] hub 2-0:1.0: USB hub found [ 4.099809] hub 2-0:1.0: 3 ports detected [ 4.109196] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.121824] mmc0: new DDR MMC card at address 0001 [ 4.126882] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.135133] mmcblk0: p1 p2 p3 p4 [ 4.146211] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.153759] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.162796] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.202252] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.211282] mmc1: new high speed SDHC card at address aaaa [ 4.220538] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.567030] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.572777] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.578642] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.586342] ata1.00: configured for UDMA/133 [ 4.590708] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.600115] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.606230] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.611743] sd 0:0:0:0: [sda] Write Protect is off [ 4.616386] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.616477] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.625672] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.668823] sda: sda1 sda2 < sda5 > [ 4.671549] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.887143] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.898083] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.902258] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.957933] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.966724] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.972251] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.977652] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.985330] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.992852] hub 3-0:1.0: USB hub found [ 4.995790] hub 3-0:1.0: 1 port detected [ 5.009341] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.017021] hub 4-0:1.0: USB hub found [ 5.020024] hub 4-0:1.0: 1 port detected [ 9.138681] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 9.450437] EXT4-fs (dm-0): mounted filesystem 24206a1e-1c1f-4c61-840d-819579290a47 ro with ordered data mode. Quota mode: disabled. [ 13.477165] usb3503 usb-hub: switched to HUB mode [ 13.480544] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 13.607186] s5p-secss 10830000.sss: s5p-sss driver registered [ 13.627079] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 13.698254] mc: Linux media interface: v0.10 [ 13.847037] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 13.879107] videodev: Linux video capture interface: v2.00 [ 14.072746] hub 1-3:1.0: USB hub found [ 14.082460] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 14.085943] hub 1-3:1.0: 3 ports detected [ 14.102245] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 14.165721] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.178675] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.186075] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.197805] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 14.208918] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 14.287653] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 14.299029] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 14.343001] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 14.351774] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 14.422513] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 14.447394] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 14.528124] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.533261] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 14.635218] hub 1-3.2:1.0: USB hub found [ 14.643692] hub 1-3.2:1.0: 4 ports detected [ 14.977274] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 15.035342] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.043101] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.051843] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.062873] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.071364] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.080072] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.150060] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 15.828936] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 15.843307] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 15.853215] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 6e:d3:ef:cc:bd:65 [ 15.889506] usbcore: registered new device driver onboard-usb-dev [ 15.896610] usb 1-3.2.4: USB disconnect, device number 4 [ 15.900941] asix 1-3.2.4:1.0 eth0: unregister 'asix' usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet [ 16.137757] hub 1-3.2:1.0: USB hub found [ 16.140718] hub 1-3.2:1.0: 4 ports detected [ 16.154772] hub 1-3.2:1.0: USB hub found [ 16.157958] hub 1-3.2:1.0: 4 ports detected [ 16.477036] usb 1-3.2.4: new high-speed USB device number 5 using exynos-ehci [ 17.329099] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:005:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 17.343970] Asix Electronics AX88772A usb-001:005:10: attached PHY driver (mii_bus:phy_addr=usb-001:005:10, irq=POLL) [ 17.353813] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 6e:d3:ef:cc:bd:65 [ 17.452995] asix 1-3.2.4:1.0 enx6ed3efccbd65: renamed from eth0 [ 17.955519] EXT4-fs (dm-0): re-mounted 24206a1e-1c1f-4c61-840d-819579290a47 r/w. Quota mode: disabled. [ 19.265263] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 19.317054] EXT4-fs (sda1): mounted filesystem dd374183-c5f7-4a89-b78c-f39beef35a7d r/w with ordered data mode. Quota mode: disabled. [ 19.413539] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 26.228869] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed