[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-21-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.90-1 (2024-05-03) [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Cubietech Cubietruck [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000048600000, size 96 MiB [ 0.000000] OF: reserved mem: initialized node default-pool, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/cubietruck--gleizes--vg-root console=ttyS0,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 1933500K/2097152K available (12288K kernel code, 1714K rwdata, 3748K rodata, 2048K init, 382K bss, 65348K reserved, 98304K cma-reserved, 1310720K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39974 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000017] Switching to timer-based delay loop, resolution 41ns [ 0.001572] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.002622] Can't get timer clock [ 0.003520] Console: colour dummy device 80x30 [ 0.003613] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003636] CPU: Testing write buffer coherency: ok [ 0.003709] pid_max: default: 32768 minimum: 301 [ 0.004271] LSM: Security Framework initializing [ 0.004379] landlock: Up and running. [ 0.004385] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.004674] AppArmor: AppArmor initialized [ 0.004689] TOMOYO Linux initialized [ 0.004731] LSM support for eBPF active [ 0.005068] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005097] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.007549] /cpus/cpu@0 missing clock-frequency property [ 0.007600] /cpus/cpu@1 missing clock-frequency property [ 0.007614] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.009125] cblist_init_generic: Setting adjustable number of callback queues. [ 0.009144] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.009328] cblist_init_generic: Setting adjustable number of callback queues. [ 0.009336] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.009586] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.010851] rcu: Hierarchical SRCU implementation. [ 0.010865] rcu: Max phase no-delay instances is 1000. [ 0.013416] EFI services will not be available. [ 0.014233] smp: Bringing up secondary CPUs ... [ 0.015621] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.015859] smp: Brought up 1 node, 2 CPUs [ 0.015877] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.015887] CPU: All CPU(s) started in HYP mode. [ 0.015890] CPU: Virtualization extensions available. [ 0.018030] devtmpfs: initialized [ 0.027452] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 [ 0.027861] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.027915] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.033318] pinctrl core: initialized pinctrl subsystem [ 0.034679] DMI not present or invalid. [ 0.035767] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.037952] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.039278] audit: initializing netlink subsys (disabled) [ 0.039816] audit: type=2000 audit(0.036:1): state=initialized audit_enabled=0 res=1 [ 0.041612] thermal_sys: Registered thermal governor 'fair_share' [ 0.041629] thermal_sys: Registered thermal governor 'bang_bang' [ 0.041634] thermal_sys: Registered thermal governor 'step_wise' [ 0.041640] thermal_sys: Registered thermal governor 'user_space' [ 0.041644] thermal_sys: Registered thermal governor 'power_allocator' [ 0.041902] No ATAGs? [ 0.042065] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.042080] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.043573] Serial: AMBA PL011 UART driver [ 0.051787] platform 1c0c000.lcd-controller: Fixed dependency cycle(s) with /soc/hdmi@1c16000 [ 0.051874] platform 1c0c000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.051942] platform 1c0c000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.052352] platform 1c0d000.lcd-controller: Fixed dependency cycle(s) with /soc/hdmi@1c16000 [ 0.052423] platform 1c0d000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.052539] platform 1c0d000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.055420] platform 1c0d000.lcd-controller: Fixed dependency cycle(s) with /soc/hdmi@1c16000 [ 0.055579] platform 1c0c000.lcd-controller: Fixed dependency cycle(s) with /soc/hdmi@1c16000 [ 0.055780] platform 1c16000.hdmi: Fixed dependency cycle(s) with /soc/lcd-controller@1c0d000 [ 0.055957] platform 1c16000.hdmi: Fixed dependency cycle(s) with /soc/lcd-controller@1c0c000 [ 0.059290] platform 1c20800.pinctrl: Fixed dependency cycle(s) with /soc/pinctrl@1c20800/clk-out-a-pin [ 0.065438] platform 1e00000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.065516] platform 1e00000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.065921] platform 1e20000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.065983] platform 1e20000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.066453] platform 1e20000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.066594] platform 1e00000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.066738] platform 1c0d000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.066853] platform 1c0c000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e40000 [ 0.066990] platform 1e40000.display-backend: Fixed dependency cycle(s) with /soc/lcd-controller@1c0d000 [ 0.067099] platform 1e40000.display-backend: Fixed dependency cycle(s) with /soc/lcd-controller@1c0c000 [ 0.067223] platform 1e40000.display-backend: Fixed dependency cycle(s) with /soc/display-frontend@1e20000 [ 0.067346] platform 1e40000.display-backend: Fixed dependency cycle(s) with /soc/display-frontend@1e00000 [ 0.067869] platform 1e20000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.068008] platform 1e00000.display-frontend: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.068120] platform 1c0d000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.068288] platform 1c0c000.lcd-controller: Fixed dependency cycle(s) with /soc/display-backend@1e60000 [ 0.068394] platform 1e60000.display-backend: Fixed dependency cycle(s) with /soc/lcd-controller@1c0d000 [ 0.068494] platform 1e60000.display-backend: Fixed dependency cycle(s) with /soc/lcd-controller@1c0c000 [ 0.068653] platform 1e60000.display-backend: Fixed dependency cycle(s) with /soc/display-frontend@1e20000 [ 0.068853] platform 1e60000.display-backend: Fixed dependency cycle(s) with /soc/display-frontend@1e00000 [ 0.072072] platform 1c16000.hdmi: Fixed dependency cycle(s) with /hdmi-connector [ 0.072259] platform hdmi-connector: Fixed dependency cycle(s) with /soc/hdmi@1c16000 [ 0.081119] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.085590] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.085612] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.094460] iommu: Default domain type: Translated [ 0.094480] iommu: DMA domain TLB invalidation policy: strict mode [ 0.096019] pps_core: LinuxPPS API ver. 1 registered [ 0.096116] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.096154] PTP clock support registered [ 0.098465] NetLabel: Initializing [ 0.098482] NetLabel: domain hash size = 128 [ 0.098491] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.098595] NetLabel: unlabeled traffic allowed by default [ 0.099051] vgaarb: loaded [ 0.100269] clocksource: Switched to clocksource arch_sys_counter [ 0.101312] VFS: Disk quotas dquot_6.6.0 [ 0.101483] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.102795] AppArmor: AppArmor Filesystem Enabled [ 0.119859] NET: Registered PF_INET protocol family [ 0.120427] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.123428] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.123617] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.123670] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.124179] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.124618] TCP: Hash tables configured (established 8192 bind 8192) [ 0.125235] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.125458] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.125565] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.126023] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.126091] NET: Registered PF_XDP protocol family [ 0.126120] PCI: CLS 0 bytes, default 64 [ 0.127007] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.127118] Trying to unpack rootfs image as initramfs... [ 0.138716] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [ 0.211072] Initialise system trusted keyrings [ 0.211208] Key type blacklist registered [ 0.213403] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.224166] zbud: loaded [ 0.226585] integrity: Platform Keyring initialized [ 0.226679] integrity: Machine keyring initialized [ 0.226696] Key type asymmetric registered [ 0.226710] Asymmetric key parser 'x509' registered [ 3.219315] Freeing initrd memory: 25116K [ 3.264405] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 3.264927] bounce: pool size: 64 pages [ 3.265268] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 3.265712] io scheduler mq-deadline registered [ 3.303765] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 3.307764] Serial: AMBA driver [ 3.309766] STM32 USART driver initialized [ 3.314025] mousedev: PS/2 mouse device common for all mice [ 3.317409] sunxi-rtc 1c20d00.rtc: registered as rtc0 [ 3.317466] sunxi-rtc 1c20d00.rtc: setting system clock to 2024-06-24T01:47:13 UTC (1719193633) [ 3.321294] ledtrig-cpu: registered to indicate activity on CPUs [ 3.325145] NET: Registered PF_INET6 protocol family [ 3.368106] Segment Routing with IPv6 [ 3.368231] In-situ OAM (IOAM) with IPv6 [ 3.368452] mip6: Mobile IPv6 [ 3.368493] NET: Registered PF_PACKET protocol family [ 3.368824] mpls_gso: MPLS GSO support [ 3.368995] ThumbEE CPU extension supported. [ 3.369017] Registering SWP/SWPB emulation handler [ 3.369700] registered taskstats version 1 [ 3.369753] Loading compiled-in X.509 certificates [ 4.258068] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 4.258253] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 4.260073] zswap: loaded using pool lzo/zbud [ 4.261384] Key type .fscrypt registered [ 4.261402] Key type fscrypt-provisioning registered [ 4.302092] Key type encrypted registered [ 4.302129] AppArmor: AppArmor sha1 policy hashing enabled [ 4.302214] ima: No TPM chip found, activating TPM-bypass! [ 4.302227] ima: Allocated hash algorithm: sha256 [ 4.302302] ima: No architecture policies found [ 4.302453] evm: Initialising EVM extended attributes: [ 4.302461] evm: security.selinux [ 4.302467] evm: security.SMACK64 (disabled) [ 4.302471] evm: security.SMACK64EXEC (disabled) [ 4.302476] evm: security.SMACK64TRANSMUTE (disabled) [ 4.302480] evm: security.SMACK64MMAP (disabled) [ 4.302484] evm: security.apparmor [ 4.302487] evm: security.ima [ 4.302491] evm: security.capability [ 4.302495] evm: HMAC attrs: 0x1 [ 5.429011] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pi not found, using dummy regulator [ 5.431715] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 5.433646] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator [ 5.434629] printk: console [ttyS0] disabled [ 5.454914] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 69, base_baud = 1500000) is a U6_16550A [ 6.807520] printk: console [ttyS0] enabled [ 6.834460] 1c28800.serial: ttyS1 at MMIO 0x1c28800 (irq = 70, base_baud = 1500000) is a U6_16550A [ 6.843837] serial serial0: tty port ttyS1 registered [ 6.850237] sun4i-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dummy regulator [ 6.862463] clk: Disabling unused clocks [ 6.877698] Freeing unused kernel image (initmem) memory: 2048K [ 6.885916] Checked W+X mappings: passed, no W+X pages found [ 6.891686] Run /init as init process [ 6.895379] with arguments: [ 6.895391] /init [ 6.895399] with environment: [ 6.895406] HOME=/ [ 6.895413] TERM=linux [ 8.294293] usbcore: registered new interface driver usbfs [ 8.300372] usbcore: registered new interface driver hub [ 8.314911] usbcore: registered new device driver usb [ 8.381304] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator [ 8.408835] sunxi-mmc 1c12000.mmc: allocated mmc-pwrseq [ 8.426761] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 8.456490] sunxi-mmc 1c12000.mmc: initialized, max. request size: 16384 KB [ 8.484710] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB [ 8.504518] SCSI subsystem initialized [ 8.505916] mmc0: new high speed SDIO card at address 0001 [ 8.534851] axp20x-i2c 0-0034: AXP20x variant AXP209 found [ 8.549839] mmc1: host does not support reading read-only switch, assuming write-enable [ 8.593918] axp20x-i2c 0-0034: mask_invert=true is deprecated; please switch to unmask_base [ 8.602755] mmc1: new high speed SDHC card at address 1234 [ 8.642932] mmcblk1: mmc1:1234 SA16G 14.5 GiB [ 8.676000] libata version 3.00 loaded. [ 8.701715] ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator [ 8.709414] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator [ 8.718271] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found [ 8.724754] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found [ 8.725633] axp20x-i2c 0-0034: AXP20X driver loaded [ 8.733954] sun7i-dwmac 1c50000.ethernet: PTP uses main clock [ 8.743374] sun7i-dwmac 1c50000.ethernet: no regulator found [ 8.754346] sun7i-dwmac 1c50000.ethernet: Version ID not available [ 8.760342] ahci-sunxi 1c18000.sata: supply phy not found, using dummy regulator [ 8.763494] sun7i-dwmac 1c50000.ethernet: DWMAC1000 [ 8.773148] sun7i-dwmac 1c50000.ethernet: No HW DMA feature register supported [ 8.780453] sun7i-dwmac 1c50000.ethernet: TX Checksum insertion supported [ 8.787313] sun7i-dwmac 1c50000.ethernet: Normal descriptors [ 8.793031] sun7i-dwmac 1c50000.ethernet: Ring mode enabled [ 8.856646] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 8.864354] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 8.894240] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 8.903416] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 8.918549] scsi host0: ahci-sunxi [ 8.922918] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 117 [ 9.088187] axp20x-gpio axp20x-gpio: DMA mask not set [ 9.096705] axp20x-gpio axp20x-gpio: AXP209 pinctrl and GPIO driver loaded [ 9.189659] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: renamed from eth0 [ 9.246936] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 9.304871] ata1.00: ATA-8: ST500LM021-1KJ152, 0001SDM1, max UDMA/133 [ 9.311378] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 9.357028] ata1.00: configured for UDMA/133 [ 9.363644] scsi 0:0:0:0: Direct-Access ATA ST500LM021-1KJ15 SDM1 PQ: 0 ANSI: 5 [ 9.377223] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not set [ 9.527721] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 9.535364] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 9.540844] sd 0:0:0:0: [sda] Write Protect is off [ 9.545701] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 9.545860] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 9.556670] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 9.598816] sda: sda1 sda2 < sda5 > [ 9.607358] sd 0:0:0:0: [sda] Attached SCSI disk [ 10.896277] random: crng init done [ 11.067636] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 11.080105] device-mapper: uevent: version 1.0.3 [ 11.085283] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 11.995026] PM: Image not found (code -22) [ 12.785968] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.811807] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 13.279080] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 17.329485] mc: Linux media interface: v0.10 [ 17.366839] sun4i-ss 1c15000.crypto-engine: no reset control found [ 17.388836] sun4i-ss 1c15000.crypto-engine: Die ID 0 [ 17.498262] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 17.557738] videodev: Linux video capture interface: v2.00 [ 17.606133] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 17.730743] Registered IR keymap rc-empty [ 17.768629] rc rc0: sunxi-ir as /devices/platform/soc/1c21800.ir/rc/rc0 [ 17.846195] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 17.856235] cfg80211: Loaded X.509 cert 'benh@debian.org: 577e021cb980e0e820821ba7b54b4961b8b4fadf' [ 17.867488] cfg80211: Loaded X.509 cert 'romain.perier@gmail.com: 3abbc6ec146e09d1b6016ab9d6cf71dd233f0328' [ 17.879545] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 17.898494] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 17.907122] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter [ 17.949147] platform regulatory.0: firmware: direct-loading firmware regulatory.db [ 17.955599] sunxi_cedrus: module is from the staging directory, the quality is unknown, you have been warned. [ 17.974085] platform regulatory.0: firmware: direct-loading firmware regulatory.db.p7s [ 18.029626] input: sunxi-ir as /devices/platform/soc/1c21800.ir/rc/rc0/input0 [ 18.049051] sunxi-ir 1c21800.ir: initialized sunXi IR driver [ 18.100527] cedrus 1c0e000.video-codec: Device registered as /dev/video0 [ 18.214527] sun4i-drm display-engine: bound 1e00000.display-frontend (ops sun4i_frontend_driver_exit [sun4i_frontend]) [ 18.254213] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip BCM43362/1 [ 18.269711] brcmfmac mmc0:0001:1: firmware: failed to load brcm/brcmfmac43362-sdio.cubietech,cubietruck.bin (-2) [ 18.280292] firmware_class: See https://wiki.debian.org/Firmware for information about missing firmware [ 18.290765] usbcore: registered new interface driver brcmfmac [ 18.312501] cryptd: max_cpu_qlen set to 1000 [ 18.318306] sun4i-drm display-engine: bound 1e20000.display-frontend (ops sun4i_frontend_driver_exit [sun4i_frontend]) [ 18.335258] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input1 [ 18.359858] brcmfmac mmc0:0001:1: firmware: failed to load brcm/brcmfmac43362-sdio.cubietech,cubietruck.bin (-2) [ 18.370330] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac43362-sdio.cubietech,cubietruck.bin failed with error -2 [ 18.373478] axp20x-adc axp20x-adc: DMA mask not set [ 18.382796] brcmfmac mmc0:0001:1: firmware: failed to load brcm/brcmfmac43362-sdio.bin (-2) [ 18.395625] brcmfmac mmc0:0001:1: firmware: failed to load brcm/brcmfmac43362-sdio.bin (-2) [ 18.396990] axp20x-battery-power-supply axp20x-battery-power-supply: DMA mask not set [ 18.404049] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac43362-sdio.bin failed with error -2 [ 18.425119] axp20x-ac-power-supply axp20x-ac-power-supply: DMA mask not set [ 18.446391] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 [ 18.510365] sun4i-drm display-engine: bound 1e60000.display-backend (ops sun4i_backend_ops [sun4i_backend]) [ 18.520738] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 [ 18.560734] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 [ 18.570064] sun4i-drm display-engine: bound 1e40000.display-backend (ops sun4i_backend_ops [sun4i_backend]) [ 18.586056] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus [ 18.624227] sun4i-drm display-engine: No panel or bridge found... RGB output disabled [ 18.632359] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_platform_driver_exit [sun4i_tcon]) [ 18.645807] sun4i-drm display-engine: No panel or bridge found... RGB output disabled [ 18.653863] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops sun4i_tcon_platform_driver_exit [sun4i_tcon]) [ 18.706554] lima 1c40000.gpu: bus rate = 300000000 [ 18.711590] lima 1c40000.gpu: mod rate = 384000000 [ 18.751191] [drm] Initialized lima 1.1.0 20191231 for 1c40000.gpu on minor 1 [ 18.768773] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 18.773764] usb_phy_generic usb_phy_generic.0.auto: supply vcc not found, using dummy regulator [ 18.787563] ehci-platform 1c1c000.usb: EHCI Host Controller [ 18.800596] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 1 [ 18.810703] usb_phy_generic usb_phy_generic.0.auto: dummy supplies not allowed for exclusive requests [ 18.811163] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 18.821904] ehci-platform 1c14000.usb: EHCI Host Controller [ 18.848500] Registered IR keymap rc-cec [ 18.860686] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 18.868774] rc rc1: sun4i as /devices/platform/soc/1c16000.hdmi/rc/rc1 [ 18.879972] ohci-platform 1c14400.usb: irq 130, io mem 0x01c14400 [ 18.901489] ehci-platform 1c1c000.usb: irq 131, io mem 0x01c1c000 [ 18.912585] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 3 [ 18.921305] input: sun4i as /devices/platform/soc/1c16000.hdmi/rc/rc1/input2 [ 18.937368] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 4 [ 18.946967] ohci-platform 1c1c400.usb: irq 132, io mem 0x01c1c400 [ 18.958120] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 18.965930] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 18.974418] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 18.981738] usb usb1: Product: Generic Platform OHCI controller [ 18.986560] sun4i-drm display-engine: bound 1c16000.hdmi (ops sun4i_hdmi_driver_exit [sun4i_drm_hdmi]) [ 18.987723] usb usb1: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 19.003747] usb usb1: SerialNumber: 1c14400.usb [ 19.008079] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 19.033077] ehci-platform 1c14000.usb: irq 133, io mem 0x01c14000 [ 19.073709] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 [ 19.087358] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 19.136924] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes [ 19.184810] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes [ 19.290887] hub 1-0:1.0: USB hub found [ 19.311794] hub 1-0:1.0: 1 port detected [ 19.347839] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 19.356454] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 19.363838] usb usb2: Product: EHCI Host Controller [ 19.368900] usb usb2: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 19.375526] usb usb2: SerialNumber: 1c1c000.usb [ 19.420515] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 [ 19.516232] hub 2-0:1.0: USB hub found [ 19.520432] hub 2-0:1.0: 1 port detected [ 19.533446] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 19.541900] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 19.549239] usb usb3: Product: Generic Platform OHCI controller [ 19.555306] usb usb3: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 19.561914] usb usb3: SerialNumber: 1c1c400.usb [ 19.571815] hub 3-0:1.0: USB hub found [ 19.575831] hub 3-0:1.0: 1 port detected [ 19.590038] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5 [ 19.590525] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 19.606517] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 19.613874] usb usb4: Product: EHCI Host Controller [ 19.618926] usb usb4: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 19.625550] usb usb4: SerialNumber: 1c14000.usb [ 19.681526] hub 4-0:1.0: USB hub found [ 19.691291] hub 4-0:1.0: 1 port detected [ 19.697348] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 19.705729] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 19.713038] usb usb5: Product: MUSB HDRC host driver [ 19.718150] usb usb5: Manufacturer: Linux 6.1.0-21-armmp-lpae musb-hcd [ 19.724760] usb usb5: SerialNumber: musb-hdrc.1.auto [ 19.794962] hub 5-0:1.0: USB hub found [ 19.801568] hub 5-0:1.0: 1 port detected [ 20.628195] Bluetooth: Core ver 2.22 [ 20.632164] NET: Registered PF_BLUETOOTH protocol family [ 20.637581] Bluetooth: HCI device and connection manager initialized [ 20.644013] Bluetooth: HCI socket layer initialized [ 20.648951] Bluetooth: L2CAP socket layer initialized [ 20.654087] Bluetooth: SCO socket layer initialized [ 20.747599] Bluetooth: HCI UART driver ver 2.3 [ 20.752164] Bluetooth: HCI UART protocol H4 registered [ 20.757571] Bluetooth: HCI UART protocol LL registered [ 20.762774] Bluetooth: HCI UART protocol ATH3K registered [ 20.769656] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 20.778760] Bluetooth: HCI UART protocol Intel registered [ 20.786325] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator [ 20.787705] Bluetooth: HCI UART protocol Broadcom registered [ 20.798904] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator [ 20.800895] Bluetooth: HCI UART protocol QCA registered [ 20.812352] Bluetooth: HCI UART protocol AG6XX registered [ 20.817954] Bluetooth: HCI UART protocol Marvell registered [ 21.210760] Bluetooth: hci0: BCM: chip id 63 [ 21.216708] Bluetooth: hci0: BCM: features 0x07 [ 21.224756] Bluetooth: hci0: BCM20702A [ 21.228748] Bluetooth: hci0: BCM20702A1 (001.002.014) build 0000 [ 21.235132] bluetooth hci0: firmware: failed to load brcm/BCM20702A1.cubietech,cubietruck.hcd (-2) [ 21.244484] bluetooth hci0: firmware: failed to load brcm/BCM20702A1.cubietech,cubietruck.hcd (-2) [ 21.253913] bluetooth hci0: firmware: failed to load brcm/BCM20702A1.hcd (-2) [ 21.261421] bluetooth hci0: firmware: failed to load brcm/BCM20702A1.hcd (-2) [ 21.269022] bluetooth hci0: firmware: failed to load brcm/BCM.cubietech,cubietruck.hcd (-2) [ 21.277764] bluetooth hci0: firmware: failed to load brcm/BCM.cubietech,cubietruck.hcd (-2) [ 21.286506] bluetooth hci0: firmware: failed to load brcm/BCM.hcd (-2) [ 21.293311] bluetooth hci0: firmware: failed to load brcm/BCM.hcd (-2) [ 21.300107] Bluetooth: hci0: BCM: firmware Patch file not found, tried: [ 21.306884] Bluetooth: hci0: BCM: 'brcm/BCM20702A1.cubietech,cubietruck.hcd' [ 21.314139] Bluetooth: hci0: BCM: 'brcm/BCM20702A1.hcd' [ 21.319516] Bluetooth: hci0: BCM: 'brcm/BCM.cubietech,cubietruck.hcd' [ 21.326063] Bluetooth: hci0: BCM: 'brcm/BCM.hcd' [ 22.372427] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 25.081808] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 25.129482] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 25.155190] EXT4-fs (dm-2): mounting ext3 file system using the ext4 subsystem [ 37.862429] ldo3: disabling [ 37.866359] ldo4: disabling [ 38.686083] EXT4-fs (dm-2): recovery complete [ 38.701287] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Quota mode: none. [ 39.001290] Adding 1949692k swap on /dev/mapper/cubietruck--gleizes--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 40.118920] audit: type=1400 audit(1719193670.736:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=991 comm="apparmor_parser" [ 40.140709] audit: type=1400 audit(1719193670.756:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=992 comm="apparmor_parser" [ 40.156114] audit: type=1400 audit(1719193670.756:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=992 comm="apparmor_parser" [ 40.211661] audit: type=1400 audit(1719193670.828:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=1005 comm="apparmor_parser" [ 40.227011] audit: type=1400 audit(1719193670.828:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=1005 comm="apparmor_parser" [ 40.242096] audit: type=1400 audit(1719193670.828:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=1005 comm="apparmor_parser" [ 40.294771] audit: type=1400 audit(1719193670.912:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/ntpd" pid=1006 comm="apparmor_parser" [ 40.323522] audit: type=1400 audit(1719193670.940:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1004 comm="apparmor_parser" [ 40.341745] audit: type=1400 audit(1719193670.940:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=1004 comm="apparmor_parser" [ 40.361179] audit: type=1400 audit(1719193670.940:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1004 comm="apparmor_parser" [ 43.835504] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 43.849871] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: PHY [stmmac-0:01] driver [RTL8211E Gigabit Ethernet] (irq=POLL) [ 43.861022] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: No Safety Features support found [ 43.869342] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: RX IPC Checksum Offload disabled [ 43.877678] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: No MAC Management Counters available [ 43.886340] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: PTP not supported by HW [ 43.895093] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: configuring for phy/rgmii-id link mode [ 48.006135] sun7i-dwmac 1c50000.ethernet enxeebdc7aefc27: Link is Up - 1Gbps/Full - flow control off [ 48.015769] IPv6: ADDRCONF(NETDEV_CHANGE): enxeebdc7aefc27: link becomes ready