[ 0.000000] Linux version 6.10.0-rc5 (osstest@himrod1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Mon Jun 24 02:21:20 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000095fff] usable [ 0.000000] Xen: [mem 0x0000000000096000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020069fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SCM/H8SCM, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000012] Xen PV: Detected 6 vCPUS [ 0.037585] tsc: Fast TSC calibration using PIT [ 0.037586] tsc: Detected 3101.181 MHz processor [ 0.037588] tsc: Detected 3101.144 MHz TSC [ 0.037802] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.037806] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.037813] last_pfn = 0x2006a max_arch_pfn = 0x400000000 [ 0.037817] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.037819] MTRRs set to read-only [ 0.037823] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.062582] RAMDISK: [mem 0x04000000-0x053b8fff] [ 0.062610] ACPI: Early table checksum verification disabled [ 0.064077] ACPI: RSDP 0x00000000000FA1D0 000024 (v02 ACPIAM) [ 0.064090] ACPI: XSDT 0x00000000DFEA0100 000084 (v01 SMCI 20131125 MSFT 00000097) [ 0.064134] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.064201] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.064214] ACPI: DSDT 0x00000000DFEA0600 005699 (v01 1BA11 1BA11000 00000000 INTL 20051117) [ 0.064225] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.064235] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.064246] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.064257] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.064268] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.064278] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.064290] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.064300] ACPI: SRAT 0x00000000DFEAA6F0 000108 (v02 AMD AGESA 00000001 AMD 00000001) [ 0.064310] ACPI: SSDT 0x00000000DFEAA800 001158 (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.064321] ACPI: EINJ 0x00000000DFEAB960 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.064332] ACPI: BERT 0x00000000DFEABAF0 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.064342] ACPI: ERST 0x00000000DFEABB20 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.064352] ACPI: HEST 0x00000000DFEABD30 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.064358] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.064360] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c98] [ 0.064361] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.064363] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.064364] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.064366] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.064367] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.064368] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.064369] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.064370] ACPI: Reserving SRAT table memory at [mem 0xdfeaa6f0-0xdfeaa7f7] [ 0.064371] ACPI: Reserving SSDT table memory at [mem 0xdfeaa800-0xdfeab957] [ 0.064373] ACPI: Reserving EINJ table memory at [mem 0xdfeab960-0xdfeaba8f] [ 0.064374] ACPI: Reserving BERT table memory at [mem 0xdfeabaf0-0xdfeabb1f] [ 0.064375] ACPI: Reserving ERST table memory at [mem 0xdfeabb20-0xdfeabd2f] [ 0.064376] ACPI: Reserving HEST table memory at [mem 0xdfeabd30-0xdfeabdd7] [ 0.064511] APIC: Switched APIC routing to: Xen PV [ 0.066718] Zone ranges: [ 0.066720] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.066723] DMA32 [mem 0x0000000001000000-0x0000000020069fff] [ 0.066725] Normal empty [ 0.066727] Movable zone start for each node [ 0.066728] Early memory node ranges [ 0.066729] node 0: [mem 0x0000000000001000-0x0000000000095fff] [ 0.066731] node 0: [mem 0x0000000000100000-0x0000000020069fff] [ 0.066734] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020069fff] [ 0.066751] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.066874] On node 0, zone DMA: 106 pages in unavailable ranges [ 0.072553] On node 0, zone DMA32: 32662 pages in unavailable ranges [ 0.072571] p2m virtual area at (____ptrval____), size is 40000000 [ 0.280003] Remapped 106 page(s) [ 0.280523] ACPI: PM-Timer IO Port: 0x808 [ 0.280567] CPU topo: CPU limit of 6 reached. Ignoring further CPUs [ 0.280601] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.280606] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.280631] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.280639] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.280654] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.280660] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.280685] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.280689] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.280705] CPU topo: Max. logical packages: 1 [ 0.280706] CPU topo: Max. logical dies: 1 [ 0.280707] CPU topo: Max. dies per package: 1 [ 0.280715] CPU topo: Max. threads per core: 1 [ 0.280716] CPU topo: Num. cores per package: 6 [ 0.280717] CPU topo: Num. threads per package: 6 [ 0.280718] CPU topo: Allowing 6 present CPUs plus 0 hotplug CPUs [ 0.280719] CPU topo: Rejected CPUs 2 [ 0.280739] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.280741] PM: hibernation: Registered nosave memory: [mem 0x00096000-0x000fffff] [ 0.280745] [mem 0x2006a000-0xdfe9dfff] available for PCI devices [ 0.280750] Booting kernel on Xen [ 0.280751] Xen version: 4.19-unstable (preserve-AD) [ 0.280758] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.287137] setup_percpu: NR_CPUS:64 nr_cpumask_bits:6 nr_cpu_ids:6 nr_node_ids:1 [ 0.288473] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u262144 [ 0.288485] pcpu-alloc: s194408 r8192 d30872 u262144 alloc=1*2097152 [ 0.288491] pcpu-alloc: [0] 0 1 2 3 4 5 - - [ 0.288591] xen: PV spinlocks enabled [ 0.288597] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.288600] Kernel command line: placeholder root=/dev/mapper/rimava1--vg-root ro console=hvc0 [ 0.288697] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.288765] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.288897] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.289161] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.289167] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.289171] software IO TLB: area num 8. [ 0.428349] Memory: 385984K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 138048K reserved, 0K cma-reserved) [ 0.428503] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.431634] Dynamic Preempt: voluntary [ 0.431784] rcu: Preemptible hierarchical RCU implementation. [ 0.431786] rcu: RCU event tracing is enabled. [ 0.431788] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.431790] Trampoline variant of Tasks RCU enabled. [ 0.431792] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.431793] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 [ 0.431820] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.438533] NR_IRQS: 4352, nr_irqs: 1016, preallocated irqs: 16 [ 0.438715] xen:events: Using FIFO-based ABI [ 0.438755] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.438762] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.438774] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.438779] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.438784] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.438789] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.438795] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.438800] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.438805] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.438810] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.438815] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.438820] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.438825] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.438830] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.438834] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.438849] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.444883] Console: colour VGA+ 80x25 [ 0.444889] printk: legacy console [tty0] enabled [ 0.458412] printk: legacy console [hvc0] enabled [ 0.459085] ACPI: Core revision 20240322 [ 0.464850] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.465010] Xen: using vcpuop timer interface [ 0.465017] installing Xen timer for CPU 0 [ 0.465268] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cb38081cf2, max_idle_ns: 440795365428 ns [ 0.465430] Calibrating delay loop (skipped), value calculated using timer frequency.. 6202.28 BogoMIPS (lpj=3101144) [ 0.465631] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.465847] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.465959] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.466076] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.466443] Spectre V2 : Mitigation: Retpolines [ 0.466546] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.466689] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.466799] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.466908] RETBleed: Mitigation: untrained return thunk [ 0.467016] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.467172] Speculative Store Bypass: Vulnerable [ 0.467304] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.467433] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.467542] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.467652] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.467761] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.495890] Freeing SMP alternatives memory: 40K [ 0.496045] pid_max: default: 32768 minimum: 301 [ 0.496207] LSM: initializing lsm=capability,selinux [ 0.496330] SELinux: Initializing. [ 0.496498] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.496645] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.497575] cpu 0 spinlock event irq 57 [ 0.497688] VPMU disabled by hypervisor. [ 0.498181] Performance Events: PMU not available due to virtualization, using software events only. [ 0.498340] signal: max sigframe size: 1776 [ 0.498498] rcu: Hierarchical SRCU implementation. [ 0.498604] rcu: Max phase no-delay instances is 400. [ 0.504717] smp: Bringing up secondary CPUs ... [ 0.505055] installing Xen timer for CPU 1 [ 0.505540] installing Xen timer for CPU 2 [ 0.505917] installing Xen timer for CPU 3 [ 0.507201] installing Xen timer for CPU 4 [ 0.509372] installing Xen timer for CPU 5 [ 0.027570] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.510497] cpu 1 spinlock event irq 87 [ 0.027570] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.510763] cpu 2 spinlock event irq 88 [ 0.027570] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.511693] cpu 3 spinlock event irq 89 [ 0.027570] [Firmware Bug]: CPU 4: APIC ID mismatch. CPUID: 0x0004 APIC: 0x0014 [ 0.512484] cpu 4 spinlock event irq 90 [ 0.027570] [Firmware Bug]: CPU 5: APIC ID mismatch. CPUID: 0x0005 APIC: 0x0015 [ 0.514429] cpu 5 spinlock event irq 91 [ 0.515901] smp: Brought up 1 node, 6 CPUs [ 0.517184] devtmpfs: initialized [ 0.517822] x86/mm: Memory block size: 128MB [ 0.523562] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.524600] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.525126] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.526164] PM: RTC time: 02:43:04, date: 2024-06-24 [ 0.527084] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.527233] xen:grant_table: Grant tables using version 1 layout [ 0.527412] Grant table initialized [ 0.527882] audit: initializing netlink subsys (disabled) [ 0.528008] audit: type=2000 audit(1719196984.639:1): state=initialized audit_enabled=0 res=1 [ 0.528539] thermal_sys: Registered thermal governor 'step_wise' [ 0.528542] thermal_sys: Registered thermal governor 'user_space' [ 0.529652] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.529914] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.604607] PCI: Using configuration type 1 for base access [ 0.604830] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.606542] ACPI: Added _OSI(Module Device) [ 0.606680] ACPI: Added _OSI(Processor Device) [ 0.606795] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.606899] ACPI: Added _OSI(Processor Aggregator Device) [ 0.615058] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.620263] xen: registering gsi 9 triggering 0 polarity 1 [ 0.632689] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.633106] ACPI: Interpreter enabled [ 0.633270] ACPI: PM: (supports S0 S1 S4 S5) [ 0.633380] ACPI: Using IOAPIC for interrupt routing [ 0.633601] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.633748] PCI: Using E820 reservations for host bridge windows [ 0.634023] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.703722] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.704127] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.704490] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.704853] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.705242] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.707959] PCI host bridge to bus 0000:00 [ 0.708320] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.708460] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.708805] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.709243] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.709458] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.709852] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.710571] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.713991] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.717230] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.717977] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.718411] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.718800] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.719582] pci 0000:00:09.0: enabling Extended Tags [ 0.720852] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.722687] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.723644] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.724097] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.724496] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.725215] pci 0000:00:0a.0: enabling Extended Tags [ 0.726353] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.728049] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601 conventional PCI endpoint [ 0.728713] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.729220] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.729600] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.730077] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.730570] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.731058] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.733247] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.733731] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.736023] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.736704] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.739090] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.739705] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.741476] pci 0000:00:12.2: supports D1 D2 [ 0.741818] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.743422] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.744096] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.746381] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.746711] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.749124] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.749723] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.751478] pci 0000:00:13.2: supports D1 D2 [ 0.751817] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.753533] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.756424] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.757124] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.757595] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.758081] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.758553] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.759040] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.759710] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.760118] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.760455] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.760806] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.762643] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.765717] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.766709] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.767115] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.767242] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.767611] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.767805] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.768745] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.769487] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.769802] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.770116] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.770505] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.770879] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.771384] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.771481] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.771645] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.771818] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.772186] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.775497] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.775832] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.776027] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.776192] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.776332] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.776708] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.779483] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.779651] pci_bus 0000:03: extended config space not accessible [ 0.779827] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.780018] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.780153] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.780622] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.781732] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.783664] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.784101] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.784250] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.784394] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.784431] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.784579] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.784801] pci_bus 0000:00: on NUMA node 0 [ 0.785473] xen: registering gsi 13 triggering 1 polarity 0 [ 0.786007] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.786209] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.786414] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.786510] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.786748] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.787024] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.787225] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.787431] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.787752] xen:balloon: Initialising balloon driver [ 0.787892] iommu: Default domain type: Translated [ 0.788432] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.788668] SCSI subsystem initialized [ 0.788783] libata version 3.00 loaded. [ 0.788783] ACPI: bus type USB registered [ 0.788783] usbcore: registered new interface driver usbfs [ 0.788784] usbcore: registered new interface driver hub [ 0.789435] usbcore: registered new device driver usb [ 0.789568] pps_core: LinuxPPS API ver. 1 registered [ 0.789673] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.789827] PTP clock support registered [ 0.790780] Advanced Linux Sound Architecture Driver Initialized. [ 0.793726] NetLabel: Initializing [ 0.794080] NetLabel: domain hash size = 128 [ 0.794459] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.794919] NetLabel: unlabeled traffic allowed by default [ 0.795082] PCI: Using ACPI for IRQ routing [ 0.827121] PCI: pci_cache_line_size set to 64 bytes [ 0.827324] e820: reserve RAM buffer [mem 0x00096000-0x0009ffff] [ 0.827331] e820: reserve RAM buffer [mem 0x2006a000-0x23ffffff] [ 0.827526] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.827611] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.827720] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.827870] vgaarb: loaded [ 0.828451] clocksource: Switched to clocksource tsc-early [ 0.829723] VFS: Disk quotas dquot_6.6.0 [ 0.829842] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.830029] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.830194] pnp: PnP ACPI init [ 0.830755] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.831034] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.831597] xen: registering gsi 8 triggering 1 polarity 0 [ 0.831868] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.832174] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.832289] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.832862] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.832977] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.833087] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.833196] system 00:05: [io 0x040b] has been reserved [ 0.833304] system 00:05: [io 0x04d6] has been reserved [ 0.833410] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.833609] system 00:05: [io 0x0c14] has been reserved [ 0.833716] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.833822] system 00:05: [io 0x0c52] has been reserved [ 0.833935] system 00:05: [io 0x0c6c] has been reserved [ 0.834056] system 00:05: [io 0x0c6f] has been reserved [ 0.834175] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.834302] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.834413] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.834561] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.834669] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.834775] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.834922] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.835045] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.835168] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.835289] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.835405] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.835555] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.835670] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.835782] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.836192] xen: registering gsi 4 triggering 1 polarity 0 [ 0.836196] Already setup the GSI :4 [ 0.836312] pnp 00:06: [dma 0 disabled] [ 0.836716] xen: registering gsi 3 triggering 1 polarity 0 [ 0.836723] pnp 00:07: [dma 0 disabled] [ 0.836906] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.837339] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.837577] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.837696] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.837807] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.837924] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.838302] pnp: PnP ACPI: found 10 devices [ 0.860868] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.861085] NET: Registered PF_INET protocol family [ 0.861345] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.862455] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.862806] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.863322] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.863585] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.863775] TCP: Hash tables configured (established 4096 bind 4096) [ 0.863968] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.864087] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.864274] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.864829] RPC: Registered named UNIX socket transport module. [ 0.864955] RPC: Registered udp transport module. [ 0.865055] RPC: Registered tcp transport module. [ 0.865156] RPC: Registered tcp-with-tls transport module. [ 0.865280] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.866319] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.866469] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.866591] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.866724] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.866831] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.866949] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.867092] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.867220] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.867349] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.867563] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.867804] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.868173] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.868469] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.868581] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.868694] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.868801] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.868911] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.869019] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.869130] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.869240] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.869351] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.869542] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.869652] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.869762] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.869872] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.870366] xen: registering gsi 16 triggering 0 polarity 1 [ 0.870510] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.520722] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 635331 usecs [ 1.520973] xen: registering gsi 16 triggering 0 polarity 1 [ 1.520990] Already setup the GSI :16 [ 1.545789] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 24293 usecs [ 1.546065] xen: registering gsi 17 triggering 0 polarity 1 [ 1.546154] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.546336] xen: registering gsi 18 triggering 0 polarity 1 [ 1.546354] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.570670] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23817 usecs [ 1.570912] xen: registering gsi 18 triggering 0 polarity 1 [ 1.570942] Already setup the GSI :18 [ 1.595733] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 24291 usecs [ 1.596057] xen: registering gsi 19 triggering 0 polarity 1 [ 1.596221] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.596581] xen: registering gsi 18 triggering 0 polarity 1 [ 1.596587] Already setup the GSI :18 [ 1.620714] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 23625 usecs [ 1.620945] PCI: CLS 64 bytes, default 64 [ 1.621118] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.621230] software IO TLB: mapped [mem 0x000000001b200000-0x000000001f200000] (64MB) [ 1.621266] Unpacking initramfs... [ 1.621523] kvm_intel: VMX not supported by CPU 0 [ 1.621682] kvm_amd: SVM not supported by CPU 0 [ 1.621811] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cb38081cf2, max_idle_ns: 440795365428 ns [ 1.622066] clocksource: Switched to clocksource tsc [ 1.634270] Initialise system trusted keyrings [ 1.635230] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.636641] NFS: Registering the id_resolver key type [ 1.636764] Key type id_resolver registered [ 1.636867] Key type id_legacy registered [ 1.637245] 9p: Installing v9fs 9p2000 file system support [ 1.659868] Key type asymmetric registered [ 1.660032] Asymmetric key parser 'x509' registered [ 1.660202] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.660364] io scheduler mq-deadline registered [ 1.660510] io scheduler kyber registered [ 1.661744] xen: registering gsi 53 triggering 0 polarity 1 [ 1.661846] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.662174] xen: registering gsi 54 triggering 0 polarity 1 [ 1.662192] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.662600] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.662792] ACPI: button: Power Button [PWRB] [ 1.662943] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.663175] ACPI: button: Power Button [PWRF] [ 1.666254] ACPI: \_PR_.P001: Found 2 idle states [ 1.666852] ACPI: \_PR_.P002: Found 2 idle states [ 1.669175] ACPI: \_PR_.P003: Found 2 idle states [ 1.670157] ACPI: \_PR_.P004: Found 2 idle states [ 1.671055] ACPI: \_PR_.P005: Found 2 idle states [ 1.672081] ACPI: \_PR_.P006: Found 2 idle states [ 1.675187] xen:xen_evtchn: Event-channel device installed [ 1.675561] xen_pciback: backend is vpci [ 1.679119] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.681851] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.687063] hpet_acpi_add: no address or irqs in _CRS [ 1.687988] Non-volatile memory driver v1.3 [ 1.708761] loop: module loaded [ 1.739481] ahci 0000:00:11.0: version 3.0 [ 1.739660] xen: registering gsi 22 triggering 0 polarity 1 [ 1.739709] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.739896] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.740062] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.740172] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.742471] scsi host0: ahci [ 1.744322] scsi host1: ahci [ 1.745311] scsi host2: ahci [ 1.745968] scsi host3: ahci [ 1.746163] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.746316] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.746486] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.746644] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.747517] tun: Universal TUN/TAP device driver, 1.6 [ 1.748525] e100: Intel(R) PRO/100 Network Driver [ 1.748935] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.749433] sky2: driver version 1.30 [ 1.749773] xen_netfront: Initialising Xen virtual ethernet driver [ 1.750805] xen: registering gsi 16 triggering 0 polarity 1 [ 1.750827] Already setup the GSI :16 [ 1.750838] xen: registering gsi 17 triggering 0 polarity 1 [ 1.750948] Already setup the GSI :17 [ 1.751038] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.751281] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 1.751439] xen: registering gsi 19 triggering 0 polarity 1 [ 1.751494] Already setup the GSI :19 [ 1.751555] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.807987] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.808178] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.808319] usb usb1: Product: OHCI PCI host controller [ 1.808426] usb usb1: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.808534] usb usb1: SerialNumber: 0000:00:12.0 [ 1.809052] hub 1-0:1.0: USB hub found [ 1.809168] hub 1-0:1.0: 3 ports detected [ 1.809802] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.810069] xen: registering gsi 16 triggering 0 polarity 1 [ 1.810084] Already setup the GSI :16 [ 1.810198] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 1.810353] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.810524] ehci-pci 0000:00:12.2: debug port 1 [ 1.811398] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.818634] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.819048] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.819228] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.819368] usb usb2: Product: EHCI Host Controller [ 1.819480] usb usb2: Manufacturer: Linux 6.10.0-rc5 ehci_hcd [ 1.819658] usb usb2: SerialNumber: 0000:00:12.2 [ 1.820145] hub 2-0:1.0: USB hub found [ 1.820281] hub 2-0:1.0: 6 ports detected [ 1.823938] Freeing initrd memory: 20196K [ 1.872985] hub 1-0:1.0: USB hub found [ 1.873197] hub 1-0:1.0: 3 ports detected [ 1.874003] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.875108] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 1.875523] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.876139] ehci-pci 0000:00:13.2: debug port 1 [ 1.877037] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.883782] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.884831] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.885007] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.885151] usb usb3: Product: EHCI Host Controller [ 1.885260] usb usb3: Manufacturer: Linux 6.10.0-rc5 ehci_hcd [ 1.885367] usb usb3: SerialNumber: 0000:00:13.2 [ 1.885813] hub 3-0:1.0: USB hub found [ 1.885929] hub 3-0:1.0: 6 ports detected [ 1.886497] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.887028] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.887257] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.943399] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.943617] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.943759] usb usb4: Product: OHCI PCI host controller [ 1.943865] usb usb4: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.943973] usb usb4: SerialNumber: 0000:00:12.1 [ 1.944663] hub 4-0:1.0: USB hub found [ 1.944858] hub 4-0:1.0: 3 ports detected [ 1.946368] xen: registering gsi 18 triggering 0 polarity 1 [ 1.946406] Already setup the GSI :18 [ 1.947045] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.947887] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.948743] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 2.005376] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.005566] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.005727] usb usb5: Product: OHCI PCI host controller [ 2.005833] usb usb5: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 2.005941] usb usb5: SerialNumber: 0000:00:13.0 [ 2.006484] hub 5-0:1.0: USB hub found [ 2.006804] hub 5-0:1.0: 3 ports detected [ 2.007759] xen: registering gsi 18 triggering 0 polarity 1 [ 2.007774] Already setup the GSI :18 [ 2.007958] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 2.008184] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 2.008394] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 2.055329] ata4: SATA link down (SStatus 0 SControl 300) [ 2.056345] ata3: SATA link down (SStatus 0 SControl 300) [ 2.063980] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.064164] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.064305] usb usb6: Product: OHCI PCI host controller [ 2.064414] usb usb6: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 2.064527] usb usb6: SerialNumber: 0000:00:13.1 [ 2.065266] hub 6-0:1.0: USB hub found [ 2.065437] hub 6-0:1.0: 3 ports detected [ 2.066033] xen: registering gsi 18 triggering 0 polarity 1 [ 2.066045] Already setup the GSI :18 [ 2.066244] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 2.066605] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 2.066812] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 2.123027] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 2.123207] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.123347] usb usb7: Product: OHCI PCI host controller [ 2.123455] usb usb7: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 2.123567] usb usb7: SerialNumber: 0000:00:14.5 [ 2.124283] hub 7-0:1.0: USB hub found [ 2.124457] hub 7-0:1.0: 2 ports detected [ 2.125022] usbcore: registered new interface driver usblp [ 2.125164] usbcore: registered new interface driver usb-storage [ 2.125315] i8042: PNP: No PS/2 controller found. [ 2.125426] i8042: Probing ports directly. [ 2.128414] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.128526] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.129065] rtc_cmos 00:02: RTC can wake from S4 [ 2.130323] rtc_cmos 00:02: registered as rtc0 [ 2.131115] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 2.131827] device-mapper: uevent: version 1.0.3 [ 2.132687] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 2.133136] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 2.133693] hid: raw HID events driver (C) Jiri Kosina [ 2.136022] usbcore: registered new interface driver usbhid [ 2.136373] usbhid: USB HID core driver [ 2.138860] Initializing XFRM netlink socket [ 2.139309] NET: Registered PF_INET6 protocol family [ 2.141114] Segment Routing with IPv6 [ 2.141238] In-situ OAM (IOAM) with IPv6 [ 2.141389] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.141748] NET: Registered PF_PACKET protocol family [ 2.141893] 9pnet: Installing 9P2000 support [ 2.142061] Key type dns_resolver registered [ 2.142184] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 2.143942] IPI shorthand broadcast: enabled [ 2.148462] sched_clock: Marking stable (2121003813, 26570940)->(2167630730, -20055977) [ 2.149061] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 2.149563] registered taskstats version 1 [ 2.149678] Loading compiled-in X.509 certificates [ 2.152007] PM: Magic number: 12:696:713 [ 2.153777] printk: legacy console [netcon0] enabled [ 2.153884] netconsole: network logging started [ 2.154180] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.166389] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.166846] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.167025] ALSA device list: [ 2.167124] No soundcards found. [ 2.168007] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 2.208791] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.210727] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 2.211554] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 32), AA [ 2.214574] ata1.00: configured for UDMA/133 [ 2.215558] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 2.216652] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.218528] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.218819] sd 0:0:0:0: [sda] Write Protect is off [ 2.218821] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.219074] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.219154] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.219426] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 2.219814] ata2.00: ATAPI: ATAPI iHAS124 E, 4L07, max UDMA/100 [ 2.220803] ata2.00: configured for UDMA/100 [ 2.222677] scsi 1:0:0:0: CD-ROM ATAPI iHAS124 E 4L07 PQ: 0 ANSI: 5 [ 2.258139] sda: sda1 sda2 < sda5 > [ 2.259293] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.266118] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.266668] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.282371] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.283024] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.285641] Freeing unused kernel image (initmem) memory: 2680K [ 2.285807] Write protecting the kernel read-only data: 24576k [ 2.329400] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.331903] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.460293] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.460757] Run /init as init process [ 2.461073] with arguments: [ 2.461085] /init [ 2.461096] placeholder [ 2.461108] with environment: [ 2.461119] HOME=/ [ 2.461130] TERM=linux [ 2.492592] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.492786] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.492903] usb 6-2: Product: Hermon USB hidmouse Device [ 2.493012] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.499075] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.499410] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.503032] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.555872] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.742967] e1000e: Intel(R) PRO/1000 Network Driver [ 2.743105] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.743333] xen: registering gsi 48 triggering 0 polarity 1 [ 2.743369] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.743627] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.786502] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.830373] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f6 [ 2.830525] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.830729] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 2.830941] xen: registering gsi 47 triggering 0 polarity 1 [ 2.830969] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.831150] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.877733] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.924118] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 0c:c4:7a:0a:48:f7 [ 2.924268] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.924456] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0101FF-0FF [ 2.926341] e1000e 0000:02:00.0 enx0cc47a0a48f7: renamed from eth1 [ 2.926714] e1000e 0000:01:00.0 enx0cc47a0a48f6: renamed from eth0 [ 3.094616] random: crng init done [ 3.758486] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.763810] EXT4-fs (dm-0): mounted filesystem ef943846-9c21-4dd7-92b0-ff1d162d0089 ro with ordered data mode. Quota mode: none. [ 7.536095] EXT4-fs (dm-0): re-mounted ef943846-9c21-4dd7-92b0-ff1d162d0089 r/w. Quota mode: none. [ 8.488983] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 8.527654] EXT4-fs (sda1): mounted filesystem 22c16976-e5e6-4471-afd3-fe33418ca4f7 r/w with ordered data mode. Quota mode: none. [ 8.768807] Adding 1949692k swap on /dev/mapper/rimava1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 10.656550] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 10.656752] xenbr0: port 1(enx0cc47a0a48f6) entered disabled state [ 10.656868] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered allmulticast mode [ 10.657022] e1000e 0000:01:00.0 enx0cc47a0a48f6: entered promiscuous mode [ 13.719644] e1000e 0000:01:00.0 enx0cc47a0a48f6: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 13.720155] xenbr0: port 1(enx0cc47a0a48f6) entered blocking state [ 13.720264] xenbr0: port 1(enx0cc47a0a48f6) entered forwarding state