[ 0.000000] Linux version 6.10.0-rc5 (osstest@himrod1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Mon Jun 24 02:21:20 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/pinot0--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000099fff] usable [ 0.000000] Xen: [mem 0x000000000009a800-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020065fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000f6000000-0x00000000f6003fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SML/H8SML, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 2/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000010] Xen PV: Detected 4 vCPUS [ 0.038871] tsc: Fast TSC calibration using PIT [ 0.038873] tsc: Detected 2799.962 MHz processor [ 0.038874] tsc: Detected 2799.992 MHz TSC [ 0.039092] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.039096] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.039103] last_pfn = 0x20066 max_arch_pfn = 0x400000000 [ 0.039106] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.039108] MTRRs set to read-only [ 0.039110] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.064745] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.064757] ACPI: Early table checksum verification disabled [ 0.065504] ACPI: RSDP 0x00000000000FA1C0 000024 (v02 ACPIAM) [ 0.065512] ACPI: XSDT 0x00000000DFEA0100 00007C (v01 SMCI 20131125 MSFT 00000097) [ 0.065538] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.065570] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.065581] ACPI: DSDT 0x00000000DFEA0600 00562B (v01 1CF11 1CF11000 00000000 INTL 20051117) [ 0.065591] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.065600] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.065610] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.065620] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.065630] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.065640] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.065650] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.065660] ACPI: SSDT 0x00000000DFEAA6F0 000B9C (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.065670] ACPI: EINJ 0x00000000DFEAB290 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.065680] ACPI: BERT 0x00000000DFEAB420 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.065690] ACPI: ERST 0x00000000DFEAB450 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.065699] ACPI: HEST 0x00000000DFEAB660 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.065705] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.065707] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c2a] [ 0.065708] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.065710] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.065711] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.065712] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.065714] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.065715] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.065716] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.065717] ACPI: Reserving SSDT table memory at [mem 0xdfeaa6f0-0xdfeab28b] [ 0.065718] ACPI: Reserving EINJ table memory at [mem 0xdfeab290-0xdfeab3bf] [ 0.065720] ACPI: Reserving BERT table memory at [mem 0xdfeab420-0xdfeab44f] [ 0.065721] ACPI: Reserving ERST table memory at [mem 0xdfeab450-0xdfeab65f] [ 0.065722] ACPI: Reserving HEST table memory at [mem 0xdfeab660-0xdfeab707] [ 0.065809] APIC: Switched APIC routing to: Xen PV [ 0.068090] Zone ranges: [ 0.068091] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.068093] DMA32 [mem 0x0000000001000000-0x0000000020065fff] [ 0.068096] Normal empty [ 0.068097] Movable zone start for each node [ 0.068098] Early memory node ranges [ 0.068098] node 0: [mem 0x0000000000001000-0x0000000000099fff] [ 0.068100] node 0: [mem 0x0000000000100000-0x0000000020065fff] [ 0.068102] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020065fff] [ 0.068110] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.068166] On node 0, zone DMA: 102 pages in unavailable ranges [ 0.070471] On node 0, zone DMA32: 32666 pages in unavailable ranges [ 0.070477] p2m virtual area at (____ptrval____), size is 40000000 [ 0.290399] Remapped 102 page(s) [ 0.290905] ACPI: PM-Timer IO Port: 0x808 [ 0.290930] CPU topo: CPU limit of 4 reached. Ignoring further CPUs [ 0.290953] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.290957] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.290976] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.290984] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.290993] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.290996] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.291014] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.291018] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.291028] CPU topo: Max. logical packages: 1 [ 0.291030] CPU topo: Max. logical dies: 1 [ 0.291030] CPU topo: Max. dies per package: 1 [ 0.291037] CPU topo: Max. threads per core: 1 [ 0.291038] CPU topo: Num. cores per package: 4 [ 0.291039] CPU topo: Num. threads per package: 4 [ 0.291039] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.291041] CPU topo: Rejected CPUs 4 [ 0.291055] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.291058] PM: hibernation: Registered nosave memory: [mem 0x0009a000-0x0009afff] [ 0.291060] PM: hibernation: Registered nosave memory: [mem 0x0009b000-0x000fffff] [ 0.291062] [mem 0x20066000-0xdfe9dfff] available for PCI devices [ 0.291066] Booting kernel on Xen [ 0.291067] Xen version: 4.19-unstable (preserve-AD) [ 0.291070] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.297322] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.297877] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.297884] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.297888] pcpu-alloc: [0] 0 1 2 3 [ 0.297941] xen: PV spinlocks enabled [ 0.297944] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.297948] Kernel command line: placeholder root=/dev/mapper/pinot0--vg-root ro console=hvc0 [ 0.298003] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.298125] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.298186] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.298367] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.298371] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.298373] software IO TLB: area num 4. [ 0.367442] Memory: 386444K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137588K reserved, 0K cma-reserved) [ 0.367547] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.370019] Dynamic Preempt: voluntary [ 0.370119] rcu: Preemptible hierarchical RCU implementation. [ 0.370120] rcu: RCU event tracing is enabled. [ 0.370121] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.370123] Trampoline variant of Tasks RCU enabled. [ 0.370124] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.370125] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.370141] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.376805] NR_IRQS: 4352, nr_irqs: 1000, preallocated irqs: 16 [ 0.376930] xen:events: Using FIFO-based ABI [ 0.376952] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.376962] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.376967] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.376973] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.376978] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.376983] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.376989] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.376994] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.376999] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.377004] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.377009] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.377015] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.377020] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.377025] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.377030] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.377039] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.383111] Console: colour VGA+ 80x25 [ 0.383115] printk: legacy console [tty0] enabled [ 0.396729] printk: legacy console [hvc0] enabled [ 0.397406] ACPI: Core revision 20240322 [ 0.401516] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.401673] Xen: using vcpuop timer interface [ 0.401679] installing Xen timer for CPU 0 [ 0.401923] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x285c3953c26, max_idle_ns: 440795321272 ns [ 0.402082] Calibrating delay loop (skipped), value calculated using timer frequency.. 5599.98 BogoMIPS (lpj=2799992) [ 0.402273] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.402510] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.402619] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.402735] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.403091] Spectre V2 : Mitigation: Retpolines [ 0.403194] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.403336] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.403447] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.403556] RETBleed: Mitigation: untrained return thunk [ 0.403662] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.403833] Speculative Store Bypass: Vulnerable [ 0.403955] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.404084] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.404195] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.404305] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.404414] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.427862] Freeing SMP alternatives memory: 40K [ 0.427983] pid_max: default: 32768 minimum: 301 [ 0.428110] LSM: initializing lsm=capability,selinux [ 0.428219] SELinux: Initializing. [ 0.428354] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.428496] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.429208] cpu 0 spinlock event irq 57 [ 0.429321] VPMU disabled by hypervisor. [ 0.429816] Performance Events: PMU not available due to virtualization, using software events only. [ 0.429977] signal: max sigframe size: 1776 [ 0.430138] rcu: Hierarchical SRCU implementation. [ 0.430245] rcu: Max phase no-delay instances is 400. [ 0.435818] smp: Bringing up secondary CPUs ... [ 0.436120] installing Xen timer for CPU 1 [ 0.436499] installing Xen timer for CPU 2 [ 0.436848] installing Xen timer for CPU 3 [ 0.026036] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.437148] cpu 1 spinlock event irq 77 [ 0.026036] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.437406] cpu 2 spinlock event irq 78 [ 0.026036] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.438132] cpu 3 spinlock event irq 79 [ 0.438390] smp: Brought up 1 node, 4 CPUs [ 0.438556] devtmpfs: initialized [ 0.439133] x86/mm: Memory block size: 128MB [ 0.439675] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.439675] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.440085] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.440300] PM: RTC time: 04:00:16, date: 2024-06-24 [ 0.440605] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.440738] xen:grant_table: Grant tables using version 1 layout [ 0.440862] Grant table initialized [ 0.441258] audit: initializing netlink subsys (disabled) [ 0.441403] audit: type=2000 audit(1719201616.752:1): state=initialized audit_enabled=0 res=1 [ 0.441403] thermal_sys: Registered thermal governor 'step_wise' [ 0.441403] thermal_sys: Registered thermal governor 'user_space' [ 0.442294] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.442590] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.522085] PCI: Using configuration type 1 for base access [ 0.522270] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.522296] ACPI: Added _OSI(Module Device) [ 0.522296] ACPI: Added _OSI(Processor Device) [ 0.523085] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.523188] ACPI: Added _OSI(Processor Aggregator Device) [ 0.528046] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.528506] xen: registering gsi 9 triggering 0 polarity 1 [ 0.531304] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.531607] ACPI: Interpreter enabled [ 0.532103] ACPI: PM: (supports S0 S1 S4 S5) [ 0.532204] ACPI: Using IOAPIC for interrupt routing [ 0.532355] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.532527] PCI: Using E820 reservations for host bridge windows [ 0.532799] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.542832] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.542947] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.543088] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.543199] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.543345] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.543788] PCI host bridge to bus 0000:00 [ 0.543889] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.544039] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.544084] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.544224] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.544368] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.544508] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.544682] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.545210] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.545793] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.546005] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.546097] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.546211] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.546379] pci 0000:00:09.0: enabling Extended Tags [ 0.546602] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.546943] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.547154] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.547275] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.547393] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.547555] pci 0000:00:0a.0: enabling Extended Tags [ 0.547775] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.548084] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f conventional PCI endpoint [ 0.548300] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.548432] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.548560] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.548687] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.548814] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.548941] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.549107] pci 0000:00:11.0: set SATA to AHCI mode [ 0.549434] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.549623] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.550005] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.550127] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.550558] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.550784] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.551116] pci 0000:00:12.2: supports D1 D2 [ 0.551218] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.551489] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.551676] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.552079] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.552267] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.552668] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.552855] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.553213] pci 0000:00:13.2: supports D1 D2 [ 0.553315] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.553642] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.554153] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.554340] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.554471] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.554598] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.554725] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.554891] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.555050] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.555083] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.555191] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.555328] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.555630] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.556162] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.556398] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.556551] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.556672] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.556951] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.557126] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.557576] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.557939] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.558250] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.558573] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.558922] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.559232] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.559702] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.559894] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.560083] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.560218] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.560611] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.563130] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.563460] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.563684] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.563847] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.563979] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.564413] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.567146] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.567313] pci_bus 0000:03: extended config space not accessible [ 0.567492] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.567685] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.567821] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.567954] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.568222] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.568716] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.568849] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.568994] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.569086] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.569249] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.569396] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.569649] pci_bus 0000:00: on NUMA node 0 [ 0.570158] xen: registering gsi 13 triggering 1 polarity 0 [ 0.570611] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.570824] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.570998] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.571150] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.571323] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.571496] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.571722] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.571900] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.572184] xen:balloon: Initialising balloon driver [ 0.572305] iommu: Default domain type: Translated [ 0.572315] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.572536] SCSI subsystem initialized [ 0.572654] libata version 3.00 loaded. [ 0.573109] ACPI: bus type USB registered [ 0.573235] usbcore: registered new interface driver usbfs [ 0.573355] usbcore: registered new interface driver hub [ 0.573475] usbcore: registered new device driver usb [ 0.573609] pps_core: LinuxPPS API ver. 1 registered [ 0.573718] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.573873] PTP clock support registered [ 0.574133] Advanced Linux Sound Architecture Driver Initialized. [ 0.574557] NetLabel: Initializing [ 0.574660] NetLabel: domain hash size = 128 [ 0.574766] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.574903] NetLabel: unlabeled traffic allowed by default [ 0.575100] PCI: Using ACPI for IRQ routing [ 0.604895] PCI: pci_cache_line_size set to 64 bytes [ 0.605083] e820: reserve RAM buffer [mem 0x0009a000-0x0009ffff] [ 0.605087] e820: reserve RAM buffer [mem 0x20066000-0x23ffffff] [ 0.605110] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.605252] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.605364] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.605540] vgaarb: loaded [ 0.607514] clocksource: Switched to clocksource tsc-early [ 0.607720] VFS: Disk quotas dquot_6.6.0 [ 0.607831] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.608014] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.608014] pnp: PnP ACPI init [ 0.608110] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.608353] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.608739] xen: registering gsi 8 triggering 1 polarity 0 [ 0.608739] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.609382] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.609502] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.609950] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.610102] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.610216] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.610337] system 00:05: [io 0x040b] has been reserved [ 0.610454] system 00:05: [io 0x04d6] has been reserved [ 0.610564] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.610677] system 00:05: [io 0x0c14] has been reserved [ 0.610787] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.610900] system 00:05: [io 0x0c52] has been reserved [ 0.611011] system 00:05: [io 0x0c6c] has been reserved [ 0.611130] system 00:05: [io 0x0c6f] has been reserved [ 0.611255] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.611370] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.611483] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.611596] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.611746] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.611859] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.611972] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.612095] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.612208] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.612321] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.612459] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.612573] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.612689] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.612805] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.613223] xen: registering gsi 4 triggering 1 polarity 0 [ 0.613227] Already setup the GSI :4 [ 0.613331] pnp 00:06: [dma 0 disabled] [ 0.613637] xen: registering gsi 3 triggering 1 polarity 0 [ 0.613662] pnp 00:07: [dma 0 disabled] [ 0.613824] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.614198] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.614401] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.614531] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.614648] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.614766] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.615068] pnp: PnP ACPI: found 10 devices [ 0.636786] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.636945] NET: Registered PF_INET protocol family [ 0.637119] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.637533] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.637687] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.637836] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.637993] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.638200] TCP: Hash tables configured (established 4096 bind 4096) [ 0.638350] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.638469] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.638623] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.640271] RPC: Registered named UNIX socket transport module. [ 0.640388] RPC: Registered udp transport module. [ 0.640490] RPC: Registered tcp transport module. [ 0.640616] RPC: Registered tcp-with-tls transport module. [ 0.640721] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.641282] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.641394] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.641512] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.641639] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.641772] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.641888] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.642015] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.642143] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.642299] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.642453] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.642562] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.642671] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.642781] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.642891] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.643027] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.643146] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.643256] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.643362] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.643470] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.643617] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.643727] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.643835] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.643943] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.644053] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.644175] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.644459] xen: registering gsi 16 triggering 0 polarity 1 [ 0.644481] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.307277] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 647350 usecs [ 1.307504] xen: registering gsi 16 triggering 0 polarity 1 [ 1.307511] Already setup the GSI :16 [ 1.330278] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 22294 usecs [ 1.330508] xen: registering gsi 17 triggering 0 polarity 1 [ 1.330554] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.330725] xen: registering gsi 18 triggering 0 polarity 1 [ 1.330742] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.353307] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 22105 usecs [ 1.353531] xen: registering gsi 18 triggering 0 polarity 1 [ 1.353539] Already setup the GSI :18 [ 1.377283] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 23248 usecs [ 1.377528] xen: registering gsi 19 triggering 0 polarity 1 [ 1.377567] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.377776] xen: registering gsi 18 triggering 0 polarity 1 [ 1.377780] Already setup the GSI :18 [ 1.401323] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 23050 usecs [ 1.401534] PCI: CLS 64 bytes, default 64 [ 1.401698] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.401814] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 1.402010] kvm_intel: VMX not supported by CPU 1 [ 1.402025] Unpacking initramfs... [ 1.402132] kvm_amd: SVM not supported by CPU 1 [ 1.402347] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x285c3953c26, max_idle_ns: 440795321272 ns [ 1.402551] clocksource: Switched to clocksource tsc [ 1.466187] Initialise system trusted keyrings [ 1.466555] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.466893] NFS: Registering the id_resolver key type [ 1.467009] Key type id_resolver registered [ 1.467129] Key type id_legacy registered [ 1.467306] 9p: Installing v9fs 9p2000 file system support [ 1.484803] Key type asymmetric registered [ 1.484907] Asymmetric key parser 'x509' registered [ 1.485025] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.485185] io scheduler mq-deadline registered [ 1.485288] io scheduler kyber registered [ 1.486145] xen: registering gsi 53 triggering 0 polarity 1 [ 1.486174] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.486441] xen: registering gsi 54 triggering 0 polarity 1 [ 1.486459] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.486784] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.486962] ACPI: button: Power Button [PWRB] [ 1.487145] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.487434] ACPI: button: Power Button [PWRF] [ 1.489678] ACPI: \_PR_.P001: Found 2 idle states [ 1.490117] ACPI: \_PR_.P002: Found 2 idle states [ 1.490287] ACPI: \_PR_.P003: Found 2 idle states [ 1.490433] ACPI: \_PR_.P004: Found 2 idle states [ 1.491071] xen:xen_evtchn: Event-channel device installed [ 1.491287] xen_pciback: backend is vpci [ 1.492078] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.492479] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.494755] hpet_acpi_add: no address or irqs in _CRS [ 1.494927] Non-volatile memory driver v1.3 [ 1.498509] loop: module loaded [ 1.505075] ahci 0000:00:11.0: version 3.0 [ 1.505176] xen: registering gsi 22 triggering 0 polarity 1 [ 1.505205] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.505351] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.505527] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.505637] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.506862] scsi host0: ahci [ 1.507243] scsi host1: ahci [ 1.507638] scsi host2: ahci [ 1.508012] scsi host3: ahci [ 1.508198] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.508352] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.508503] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.508663] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.509295] tun: Universal TUN/TAP device driver, 1.6 [ 1.509517] e100: Intel(R) PRO/100 Network Driver [ 1.509628] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.509758] sky2: driver version 1.30 [ 1.509922] xen_netfront: Initialising Xen virtual ethernet driver [ 1.510306] xen: registering gsi 16 triggering 0 polarity 1 [ 1.510313] Already setup the GSI :16 [ 1.510485] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.510552] xen: registering gsi 19 triggering 0 polarity 1 [ 1.510560] xen: registering gsi 17 triggering 0 polarity 1 [ 1.510565] Already setup the GSI :17 [ 1.510715] Already setup the GSI :19 [ 1.510719] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 1.511029] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.563684] Freeing initrd memory: 20192K [ 1.567389] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.567543] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.567683] usb usb1: Product: OHCI PCI host controller [ 1.567805] usb usb1: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.567912] usb usb1: SerialNumber: 0000:00:12.0 [ 1.568402] hub 1-0:1.0: USB hub found [ 1.568538] hub 1-0:1.0: 3 ports detected [ 1.569138] xen: registering gsi 16 triggering 0 polarity 1 [ 1.569146] Already setup the GSI :16 [ 1.569152] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.569461] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 1.569606] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.569771] ehci-pci 0000:00:12.2: debug port 1 [ 1.569990] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.577107] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.577307] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.577486] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.577626] usb usb2: Product: EHCI Host Controller [ 1.577729] usb usb2: Manufacturer: Linux 6.10.0-rc5 ehci_hcd [ 1.577836] usb usb2: SerialNumber: 0000:00:12.2 [ 1.578220] hub 2-0:1.0: USB hub found [ 1.578371] hub 2-0:1.0: 6 ports detected [ 1.630126] hub 1-0:1.0: USB hub found [ 1.630245] hub 1-0:1.0: 3 ports detected [ 1.630597] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.630796] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 1.630941] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.631133] ehci-pci 0000:00:13.2: debug port 1 [ 1.631351] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.638067] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.638401] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.638579] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.638719] usb usb3: Product: EHCI Host Controller [ 1.638823] usb usb3: Manufacturer: Linux 6.10.0-rc5 ehci_hcd [ 1.638930] usb usb3: SerialNumber: 0000:00:13.2 [ 1.639240] hub 3-0:1.0: USB hub found [ 1.639386] hub 3-0:1.0: 6 ports detected [ 1.639850] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.640137] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.640319] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.696303] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.696455] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.696595] usb usb4: Product: OHCI PCI host controller [ 1.696699] usb usb4: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.696806] usb usb4: SerialNumber: 0000:00:12.1 [ 1.697176] hub 4-0:1.0: USB hub found [ 1.697321] hub 4-0:1.0: 3 ports detected [ 1.697826] xen: registering gsi 18 triggering 0 polarity 1 [ 1.697832] Already setup the GSI :18 [ 1.697968] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.698180] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.698381] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 1.754320] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.754512] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.754676] usb usb5: Product: OHCI PCI host controller [ 1.754781] usb usb5: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.754888] usb usb5: SerialNumber: 0000:00:13.0 [ 1.755256] hub 5-0:1.0: USB hub found [ 1.755392] hub 5-0:1.0: 3 ports detected [ 1.755952] xen: registering gsi 18 triggering 0 polarity 1 [ 1.755959] Already setup the GSI :18 [ 1.756120] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 1.756309] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 1.756483] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 1.812392] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.812545] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.812687] usb usb6: Product: OHCI PCI host controller [ 1.812813] usb usb6: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.812920] usb usb6: SerialNumber: 0000:00:13.1 [ 1.813286] hub 6-0:1.0: USB hub found [ 1.813422] hub 6-0:1.0: 3 ports detected [ 1.813953] xen: registering gsi 18 triggering 0 polarity 1 [ 1.813959] Already setup the GSI :18 [ 1.814156] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 1.814347] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 1.814543] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 1.817333] ata3: SATA link down (SStatus 0 SControl 300) [ 1.817478] ata4: SATA link down (SStatus 0 SControl 300) [ 1.870312] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.870464] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.870604] usb usb7: Product: OHCI PCI host controller [ 1.870722] usb usb7: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.870829] usb usb7: SerialNumber: 0000:00:14.5 [ 1.871202] hub 7-0:1.0: USB hub found [ 1.871337] hub 7-0:1.0: 2 ports detected [ 1.871772] usbcore: registered new interface driver usblp [ 1.871927] usbcore: registered new interface driver usb-storage [ 1.872095] i8042: PNP: No PS/2 controller found. [ 1.872198] i8042: Probing ports directly. [ 1.875477] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.875601] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.875980] rtc_cmos 00:02: RTC can wake from S4 [ 1.876548] rtc_cmos 00:02: registered as rtc0 [ 1.876699] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 1.876869] device-mapper: uevent: version 1.0.3 [ 1.877125] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.877279] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 1.877435] hid: raw HID events driver (C) Jiri Kosina [ 1.877756] usbcore: registered new interface driver usbhid [ 1.877867] usbhid: USB HID core driver [ 1.878432] Initializing XFRM netlink socket [ 1.878604] NET: Registered PF_INET6 protocol family [ 1.879292] Segment Routing with IPv6 [ 1.879407] In-situ OAM (IOAM) with IPv6 [ 1.879544] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.879803] NET: Registered PF_PACKET protocol family [ 1.879933] 9pnet: Installing 9P2000 support [ 1.880071] Key type dns_resolver registered [ 1.880188] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 1.880785] IPI shorthand broadcast: enabled [ 1.885326] sched_clock: Marking stable (1860003935, 25036992)->(1892382765, -7341838) [ 1.885836] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.886295] registered taskstats version 1 [ 1.886397] Loading compiled-in X.509 certificates [ 1.888609] PM: Magic number: 12:187:10 [ 1.888716] hub 5-0:1.0: hash matches [ 1.888866] printk: legacy console [netcon0] enabled [ 1.888974] netconsole: network logging started [ 1.889230] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 1.899482] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 1.899871] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 1.900098] ALSA device list: [ 1.902418] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 1.902603] No soundcards found. [ 1.971083] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.971221] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.971705] ata2.00: ATA-9: WDC WD1003FZEX-00MK2A0, 01.01A01, max UDMA/133 [ 1.972210] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 1.972989] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 1.973265] ata2.00: configured for UDMA/133 [ 1.973668] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 1.975506] ata1.00: configured for UDMA/133 [ 1.975789] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 1.976748] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.976786] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.977085] sd 0:0:0:0: [sda] Write Protect is off [ 1.977200] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.977265] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.977289] scsi 1:0:0:0: Direct-Access ATA WDC WD1003FZEX-0 1A01 PQ: 0 ANSI: 5 [ 1.977510] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 1.978247] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 1.978250] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.978511] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 1.978643] sd 1:0:0:0: [sdb] Write Protect is off [ 1.978753] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1.978806] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.979049] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 2.000940] sda: sda1 sda2 < sda5 > [ 2.001348] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.009477] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.011562] Freeing unused kernel image (initmem) memory: 2680K [ 2.011716] Write protecting the kernel read-only data: 24576k [ 2.026491] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.131072] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.142523] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.142672] Run /init as init process [ 2.142781] with arguments: [ 2.142782] /init [ 2.142784] placeholder [ 2.142785] with environment: [ 2.142787] HOME=/ [ 2.142788] TERM=linux [ 2.297197] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.297359] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.297473] usb 6-2: Product: Hermon USB hidmouse Device [ 2.297578] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.303695] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.303996] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.307682] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.359451] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.412531] e1000e: Intel(R) PRO/1000 Network Driver [ 2.412657] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.412882] xen: registering gsi 48 triggering 0 polarity 1 [ 2.412962] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.413290] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.459992] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.503995] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e8:ac [ 2.504159] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.504350] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.504559] xen: registering gsi 47 triggering 0 polarity 1 [ 2.504587] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.504842] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.552087] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.596999] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e8:ad [ 2.597160] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.597352] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.599309] e1000e 0000:01:00.0 enx002590aee8ac: renamed from eth0 [ 2.600831] e1000e 0000:02:00.0 enx002590aee8ad: renamed from eth1 [ 2.602602] random: crng init done [ 3.233276] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.239438] EXT4-fs (dm-0): mounted filesystem 48103283-5c22-4a8c-90f3-c61251e44869 ro with ordered data mode. Quota mode: none. [ 7.425328] EXT4-fs (dm-0): re-mounted 48103283-5c22-4a8c-90f3-c61251e44869 r/w. Quota mode: none. [ 9.039871] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 9.057956] EXT4-fs (sda1): mounted filesystem d8b7f3dd-066f-473b-995e-1a7e9eae961d r/w with ordered data mode. Quota mode: none. [ 9.146669] Adding 1949692k swap on /dev/mapper/pinot0--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 10.650629] xenbr0: port 1(enx002590aee8ac) entered blocking state [ 10.650772] xenbr0: port 1(enx002590aee8ac) entered disabled state [ 10.650900] e1000e 0000:01:00.0 enx002590aee8ac: entered allmulticast mode [ 10.651076] e1000e 0000:01:00.0 enx002590aee8ac: entered promiscuous mode [ 13.799089] e1000e 0000:01:00.0 enx002590aee8ac: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 13.799663] xenbr0: port 1(enx002590aee8ac) entered blocking state [ 13.799774] xenbr0: port 1(enx002590aee8ac) entered forwarding state