[ 0.000000] Linux version 6.10.0-rc5 (osstest@himrod2) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Mon Jun 24 08:57:45 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/pinot0--vg-root ro console=hvc0 [ 0.000000] [Firmware Bug]: TSC doesn't count with P0 frequency! [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x0000000000099fff] usable [ 0.000000] Xen: [mem 0x000000000009a800-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020065fff] usable [ 0.000000] Xen: [mem 0x00000000dfe9e000-0x00000000dfe9ffff] type 9 [ 0.000000] Xen: [mem 0x00000000dfea0000-0x00000000dfeb1fff] ACPI data [ 0.000000] Xen: [mem 0x00000000dfeb2000-0x00000000dfedffff] ACPI NVS [ 0.000000] Xen: [mem 0x00000000dfee0000-0x00000000efffffff] reserved [ 0.000000] Xen: [mem 0x00000000f6000000-0x00000000f6003fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fec20000-0x00000000fec20fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved [ 0.000000] Xen: [mem 0x000000fd00000000-0x000000ffffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.6 present. [ 0.000000] DMI: Supermicro H8SML/H8SML, BIOS 3.5 11/25/2013 [ 0.000000] DMI: Memory slots populated: 2/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000010] Xen PV: Detected 4 vCPUS [ 0.039085] tsc: Fast TSC calibration using PIT [ 0.039086] tsc: Detected 2800.144 MHz processor [ 0.039088] tsc: Detected 2799.988 MHz TSC [ 0.039309] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.039313] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.039320] last_pfn = 0x20066 max_arch_pfn = 0x400000000 [ 0.039323] MTRR map: 1 entries (0 fixed + 1 variable; max 16), built from 8 variable MTRRs [ 0.039325] MTRRs set to read-only [ 0.039328] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.064845] RAMDISK: [mem 0x04000000-0x053b7fff] [ 0.064857] ACPI: Early table checksum verification disabled [ 0.065604] ACPI: RSDP 0x00000000000FA1C0 000024 (v02 ACPIAM) [ 0.065613] ACPI: XSDT 0x00000000DFEA0100 00007C (v01 SMCI 20131125 MSFT 00000097) [ 0.065639] ACPI: FACP 0x00000000DFEA0290 0000F4 (v03 112513 FACP1100 20131125 MSFT 00000097) [ 0.065672] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20240322/tbfadt-560) [ 0.065682] ACPI: DSDT 0x00000000DFEA0600 00562B (v01 1CF11 1CF11000 00000000 INTL 20051117) [ 0.065693] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.065702] ACPI: FACS 0x00000000DFEB2000 000040 [ 0.065712] ACPI: APIC 0x00000000DFEA0390 0000A4 (v01 112513 APIC1100 20131125 MSFT 00000097) [ 0.065722] ACPI: MCFG 0x00000000DFEA0440 00003C (v01 112513 OEMMCFG 20131125 MSFT 00000097) [ 0.065732] ACPI: OEMB 0x00000000DFEB2040 000075 (v01 112513 OEMB1100 20131125 MSFT 00000097) [ 0.065741] ACPI: HPET 0x00000000DFEAA600 000038 (v01 112513 OEMHPET 20131125 MSFT 00000097) [ 0.065751] ACPI: IVRS 0x00000000DFEAA640 0000B0 (v01 AMD RD890S 00202031 AMD 00000000) [ 0.065761] ACPI: SSDT 0x00000000DFEAA6F0 000B9C (v01 A M I POWERNOW 00000001 AMD 00000001) [ 0.065771] ACPI: EINJ 0x00000000DFEAB290 000130 (v01 AMIER AMI_EINJ 20131125 MSFT 00000097) [ 0.065781] ACPI: BERT 0x00000000DFEAB420 000030 (v01 AMIER AMI_BERT 20131125 MSFT 00000097) [ 0.065791] ACPI: ERST 0x00000000DFEAB450 000210 (v01 AMIER AMI_ERST 20131125 MSFT 00000097) [ 0.065800] ACPI: HEST 0x00000000DFEAB660 0000A8 (v01 AMIER ABC_HEST 20131125 MSFT 00000097) [ 0.065806] ACPI: Reserving FACP table memory at [mem 0xdfea0290-0xdfea0383] [ 0.065808] ACPI: Reserving DSDT table memory at [mem 0xdfea0600-0xdfea5c2a] [ 0.065809] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.065810] ACPI: Reserving FACS table memory at [mem 0xdfeb2000-0xdfeb203f] [ 0.065812] ACPI: Reserving APIC table memory at [mem 0xdfea0390-0xdfea0433] [ 0.065813] ACPI: Reserving MCFG table memory at [mem 0xdfea0440-0xdfea047b] [ 0.065814] ACPI: Reserving OEMB table memory at [mem 0xdfeb2040-0xdfeb20b4] [ 0.065815] ACPI: Reserving HPET table memory at [mem 0xdfeaa600-0xdfeaa637] [ 0.065817] ACPI: Reserving IVRS table memory at [mem 0xdfeaa640-0xdfeaa6ef] [ 0.065818] ACPI: Reserving SSDT table memory at [mem 0xdfeaa6f0-0xdfeab28b] [ 0.065819] ACPI: Reserving EINJ table memory at [mem 0xdfeab290-0xdfeab3bf] [ 0.065820] ACPI: Reserving BERT table memory at [mem 0xdfeab420-0xdfeab44f] [ 0.065821] ACPI: Reserving ERST table memory at [mem 0xdfeab450-0xdfeab65f] [ 0.065823] ACPI: Reserving HEST table memory at [mem 0xdfeab660-0xdfeab707] [ 0.065910] APIC: Switched APIC routing to: Xen PV [ 0.068190] Zone ranges: [ 0.068191] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.068194] DMA32 [mem 0x0000000001000000-0x0000000020065fff] [ 0.068196] Normal empty [ 0.068197] Movable zone start for each node [ 0.068198] Early memory node ranges [ 0.068199] node 0: [mem 0x0000000000001000-0x0000000000099fff] [ 0.068201] node 0: [mem 0x0000000000100000-0x0000000020065fff] [ 0.068203] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020065fff] [ 0.068210] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.068269] On node 0, zone DMA: 102 pages in unavailable ranges [ 0.070575] On node 0, zone DMA32: 32666 pages in unavailable ranges [ 0.070582] p2m virtual area at (____ptrval____), size is 40000000 [ 0.290493] Remapped 102 page(s) [ 0.290998] ACPI: PM-Timer IO Port: 0x808 [ 0.291022] CPU topo: CPU limit of 4 reached. Ignoring further CPUs [ 0.291046] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.291049] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.291068] IOAPIC[0]: apic_id 0, version 33, address 0xfec00000, GSI 0-23 [ 0.291075] IOAPIC[1]: apic_id 1, version 33, address 0xfec20000, GSI 24-55 [ 0.291085] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.291089] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.291106] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.291110] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.291120] CPU topo: Max. logical packages: 1 [ 0.291121] CPU topo: Max. logical dies: 1 [ 0.291122] CPU topo: Max. dies per package: 1 [ 0.291128] CPU topo: Max. threads per core: 1 [ 0.291129] CPU topo: Num. cores per package: 4 [ 0.291130] CPU topo: Num. threads per package: 4 [ 0.291131] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.291132] CPU topo: Rejected CPUs 4 [ 0.291147] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.291149] PM: hibernation: Registered nosave memory: [mem 0x0009a000-0x0009afff] [ 0.291151] PM: hibernation: Registered nosave memory: [mem 0x0009b000-0x000fffff] [ 0.291153] [mem 0x20066000-0xdfe9dfff] available for PCI devices [ 0.291156] Booting kernel on Xen [ 0.291157] Xen version: 4.19-unstable (preserve-AD) [ 0.291160] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.297408] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.297965] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.297973] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.297976] pcpu-alloc: [0] 0 1 2 3 [ 0.298028] xen: PV spinlocks enabled [ 0.298032] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.298035] Kernel command line: placeholder root=/dev/mapper/pinot0--vg-root ro console=hvc0 [ 0.298090] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.298215] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.298275] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.298458] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.298461] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.298464] software IO TLB: area num 4. [ 0.367472] Memory: 386444K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137588K reserved, 0K cma-reserved) [ 0.367578] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.370045] Dynamic Preempt: voluntary [ 0.370145] rcu: Preemptible hierarchical RCU implementation. [ 0.370146] rcu: RCU event tracing is enabled. [ 0.370147] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.370149] Trampoline variant of Tasks RCU enabled. [ 0.370150] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.370152] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.370168] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.376809] NR_IRQS: 4352, nr_irqs: 1000, preallocated irqs: 16 [ 0.376933] xen:events: Using FIFO-based ABI [ 0.376956] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.376965] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.376971] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.376976] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.376981] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.376986] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.376992] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.376997] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.377002] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.377007] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.377012] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.377018] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.377023] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.377028] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.377033] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.377043] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.383175] Console: colour VGA+ 80x25 [ 0.383179] printk: legacy console [tty0] enabled [ 0.396795] printk: legacy console [hvc0] enabled [ 0.397469] ACPI: Core revision 20240322 [ 0.401528] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.401685] Xen: using vcpuop timer interface [ 0.401690] installing Xen timer for CPU 0 [ 0.401933] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x285c3559aad, max_idle_ns: 440795319783 ns [ 0.402091] Calibrating delay loop (skipped), value calculated using timer frequency.. 5599.97 BogoMIPS (lpj=2799988) [ 0.402284] [Firmware Bug]: CPU 0: APIC ID mismatch. CPUID: 0x0000 APIC: 0x0010 [ 0.402537] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.402648] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.402763] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.403100] Spectre V2 : Mitigation: Retpolines [ 0.403203] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.403346] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.403456] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.403566] RETBleed: Mitigation: untrained return thunk [ 0.403696] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.403841] Speculative Store Bypass: Vulnerable [ 0.403962] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.404094] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.404204] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.404313] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.404423] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.427914] Freeing SMP alternatives memory: 40K [ 0.428062] pid_max: default: 32768 minimum: 301 [ 0.428120] LSM: initializing lsm=capability,selinux [ 0.428229] SELinux: Initializing. [ 0.428362] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.428505] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.429217] cpu 0 spinlock event irq 57 [ 0.429330] VPMU disabled by hypervisor. [ 0.429822] Performance Events: PMU not available due to virtualization, using software events only. [ 0.429982] signal: max sigframe size: 1776 [ 0.430147] rcu: Hierarchical SRCU implementation. [ 0.430290] rcu: Max phase no-delay instances is 400. [ 0.435848] smp: Bringing up secondary CPUs ... [ 0.436144] installing Xen timer for CPU 1 [ 0.436523] installing Xen timer for CPU 2 [ 0.436878] installing Xen timer for CPU 3 [ 0.026043] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0011 [ 0.437161] cpu 1 spinlock event irq 77 [ 0.026043] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0012 [ 0.437418] cpu 2 spinlock event irq 78 [ 0.026043] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0013 [ 0.438145] cpu 3 spinlock event irq 79 [ 0.438390] smp: Brought up 1 node, 4 CPUs [ 0.438531] devtmpfs: initialized [ 0.439142] x86/mm: Memory block size: 128MB [ 0.439686] ACPI: PM: Registering ACPI NVS region [mem 0xdfeb2000-0xdfedffff] (188416 bytes) [ 0.439686] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.440095] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.440311] PM: RTC time: 10:16:15, date: 2024-06-24 [ 0.440612] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.440746] xen:grant_table: Grant tables using version 1 layout [ 0.440869] Grant table initialized [ 0.441206] audit: initializing netlink subsys (disabled) [ 0.441354] audit: type=2000 audit(1719224176.142:1): state=initialized audit_enabled=0 res=1 [ 0.441354] thermal_sys: Registered thermal governor 'step_wise' [ 0.441354] thermal_sys: Registered thermal governor 'user_space' [ 0.442312] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.442608] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.522175] PCI: Using configuration type 1 for base access [ 0.522386] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.523099] ACPI: Added _OSI(Module Device) [ 0.523207] ACPI: Added _OSI(Processor Device) [ 0.523309] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.523411] ACPI: Added _OSI(Processor Aggregator Device) [ 0.528295] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.528831] xen: registering gsi 9 triggering 0 polarity 1 [ 0.529278] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.529578] ACPI: Interpreter enabled [ 0.529696] ACPI: PM: (supports S0 S1 S4 S5) [ 0.529797] ACPI: Using IOAPIC for interrupt routing [ 0.530130] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.530291] PCI: Using E820 reservations for host bridge windows [ 0.530602] ACPI: Enabled 4 GPEs in block 00 to 1F [ 0.540665] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.540781] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.540932] acpi PNP0A08:00: _OSC: OS requested [PME PCIeCapability LTR] [ 0.541042] acpi PNP0A08:00: _OSC: platform willing to grant [PME PCIeCapability LTR] [ 0.541093] acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND) [ 0.541550] PCI host bridge to bus 0000:00 [ 0.541652] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.541763] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.541874] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.542014] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window] [ 0.542093] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window] [ 0.542260] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.542412] pci 0000:00:00.0: [1002:5a13] type 00 class 0x060000 conventional PCI endpoint [ 0.542983] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600 conventional PCI endpoint [ 0.543479] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400 PCIe Root Port [ 0.543693] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.543811] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.543925] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.544106] pci 0000:00:09.0: enabling Extended Tags [ 0.544328] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold [ 0.544625] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400 PCIe Root Port [ 0.544838] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.544955] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.545068] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.545144] pci 0000:00:0a.0: enabling Extended Tags [ 0.545410] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold [ 0.545739] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f conventional PCI endpoint [ 0.545926] pci 0000:00:11.0: BAR 0 [io 0xc000-0xc007] [ 0.546054] pci 0000:00:11.0: BAR 1 [io 0xb000-0xb003] [ 0.546116] pci 0000:00:11.0: BAR 2 [io 0xa000-0xa007] [ 0.546243] pci 0000:00:11.0: BAR 3 [io 0x9000-0x9003] [ 0.546375] pci 0000:00:11.0: BAR 4 [io 0x8000-0x800f] [ 0.546506] pci 0000:00:11.0: BAR 5 [mem 0xfebfbc00-0xfebfbfff] [ 0.546709] pci 0000:00:11.0: set SATA to AHCI mode [ 0.547051] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.547136] pci 0000:00:12.0: BAR 0 [mem 0xfebf9000-0xfebf9fff] [ 0.547525] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.547713] pci 0000:00:12.1: BAR 0 [mem 0xfebfa000-0xfebfafff] [ 0.548178] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.548370] pci 0000:00:12.2: BAR 0 [mem 0xfebfb800-0xfebfb8ff] [ 0.548700] pci 0000:00:12.2: supports D1 D2 [ 0.548801] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.549065] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.549136] pci 0000:00:13.0: BAR 0 [mem 0xfebf7000-0xfebf7fff] [ 0.549530] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.549717] pci 0000:00:13.1: BAR 0 [mem 0xfebf8000-0xfebf8fff] [ 0.550116] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.550333] pci 0000:00:13.2: BAR 0 [mem 0xfebfb400-0xfebfb4ff] [ 0.550670] pci 0000:00:13.2: supports D1 D2 [ 0.550771] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.551053] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.551492] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.551678] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.551806] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.551972] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.552099] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.552231] pci 0000:00:14.1: BAR 4 [io 0xff00-0xff0f] [ 0.552391] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.552501] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.552634] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.552744] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.553041] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.553483] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.553741] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.553868] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.553989] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.554232] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.554420] pci 0000:00:14.5: BAR 0 [mem 0xfebf6000-0xfebf6fff] [ 0.554857] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.555230] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.555540] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.555901] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.556254] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.556563] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.557027] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.557184] pci 0000:01:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff] [ 0.557374] pci 0000:01:00.0: BAR 2 [io 0xd800-0xd81f] [ 0.557506] pci 0000:01:00.0: BAR 3 [mem 0xfe9dc000-0xfe9dffff] [ 0.557872] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.561140] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.561443] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000 PCIe Endpoint [ 0.561639] pci 0000:02:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff] [ 0.561834] pci 0000:02:00.0: BAR 2 [io 0xe800-0xe81f] [ 0.561967] pci 0000:02:00.0: BAR 3 [mem 0xfeadc000-0xfeadffff] [ 0.562360] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.565138] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.565345] pci_bus 0000:03: extended config space not accessible [ 0.565541] pci 0000:03:04.0: [102b:0532] type 00 class 0x030000 conventional PCI endpoint [ 0.565765] pci 0000:03:04.0: BAR 0 [mem 0xfc000000-0xfcffffff pref] [ 0.565902] pci 0000:03:04.0: BAR 1 [mem 0xfdffc000-0xfdffffff] [ 0.566035] pci 0000:03:04.0: BAR 2 [mem 0xfe000000-0xfe7fffff] [ 0.566225] pci 0000:03:04.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.566715] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode) [ 0.566849] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.566994] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.567095] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.567244] pci 0000:00:14.4: bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode) [ 0.567391] pci 0000:00:14.4: bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode) [ 0.567670] pci_bus 0000:00: on NUMA node 0 [ 0.568168] xen: registering gsi 13 triggering 1 polarity 0 [ 0.568640] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.568826] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.569004] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.569161] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.569334] ACPI: PCI: Interrupt link LNKE configured for IRQ 7 [ 0.569513] ACPI: PCI: Interrupt link LNKF configured for IRQ 10 [ 0.569688] ACPI: PCI: Interrupt link LNKG configured for IRQ 11 [ 0.569865] ACPI: PCI: Interrupt link LNKH configured for IRQ 10 [ 0.570103] xen:balloon: Initialising balloon driver [ 0.570224] iommu: Default domain type: Translated [ 0.570328] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.570523] SCSI subsystem initialized [ 0.570641] libata version 3.00 loaded. [ 0.570641] ACPI: bus type USB registered [ 0.571115] usbcore: registered new interface driver usbfs [ 0.571234] usbcore: registered new interface driver hub [ 0.571354] usbcore: registered new device driver usb [ 0.571484] pps_core: LinuxPPS API ver. 1 registered [ 0.571594] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.571763] PTP clock support registered [ 0.571897] Advanced Linux Sound Architecture Driver Initialized. [ 0.572406] NetLabel: Initializing [ 0.572511] NetLabel: domain hash size = 128 [ 0.572617] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.572750] NetLabel: unlabeled traffic allowed by default [ 0.572885] PCI: Using ACPI for IRQ routing [ 0.602998] PCI: pci_cache_line_size set to 64 bytes [ 0.603188] e820: reserve RAM buffer [mem 0x0009a000-0x0009ffff] [ 0.603193] e820: reserve RAM buffer [mem 0x20066000-0x23ffffff] [ 0.603255] pci 0000:03:04.0: vgaarb: setting as boot VGA device [ 0.603255] pci 0000:03:04.0: vgaarb: bridge control possible [ 0.603348] pci 0000:03:04.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.603524] vgaarb: loaded [ 0.603879] clocksource: Switched to clocksource tsc-early [ 0.603879] VFS: Disk quotas dquot_6.6.0 [ 0.603879] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.603879] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.603879] pnp: PnP ACPI init [ 0.604106] system 00:00: [mem 0xfec20000-0xfec200ff] could not be reserved [ 0.604215] system 00:01: [mem 0xf6000000-0xf6003fff] has been reserved [ 0.604215] xen: registering gsi 8 triggering 1 polarity 0 [ 0.604215] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.605402] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.605524] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.605972] system 00:05: [io 0x0ca2-0x0ca3] has been reserved [ 0.606088] system 00:05: [io 0x0550-0x0551] has been reserved [ 0.606213] system 00:05: [io 0x04d0-0x04d1] has been reserved [ 0.606352] system 00:05: [io 0x040b] has been reserved [ 0.606478] system 00:05: [io 0x04d6] has been reserved [ 0.606589] system 00:05: [io 0x0c00-0x0c01] has been reserved [ 0.606703] system 00:05: [io 0x0c14] has been reserved [ 0.606814] system 00:05: [io 0x0c50-0x0c51] has been reserved [ 0.606927] system 00:05: [io 0x0c52] has been reserved [ 0.607038] system 00:05: [io 0x0c6c] has been reserved [ 0.607157] system 00:05: [io 0x0c6f] has been reserved [ 0.607269] system 00:05: [io 0x0cd0-0x0cd1] has been reserved [ 0.607383] system 00:05: [io 0x0cd2-0x0cd3] has been reserved [ 0.607497] system 00:05: [io 0x0cd4-0x0cd5] has been reserved [ 0.607624] system 00:05: [io 0x0cd6-0x0cd7] has been reserved [ 0.607738] system 00:05: [io 0x0cd8-0x0cdf] has been reserved [ 0.607864] system 00:05: [io 0x0800-0x089f] has been reserved [ 0.607977] system 00:05: [io 0x0b00-0x0b0f] has been reserved [ 0.608099] system 00:05: [io 0x0b20-0x0b3f] has been reserved [ 0.608213] system 00:05: [io 0x0900-0x090f] has been reserved [ 0.608326] system 00:05: [io 0x0910-0x091f] has been reserved [ 0.608439] system 00:05: [io 0xfe00-0xfefe] has been reserved [ 0.608553] system 00:05: [mem 0xffb80000-0xffbfffff] has been reserved [ 0.608669] system 00:05: [mem 0xfec10000-0xfec1001f] has been reserved [ 0.608810] system 00:05: [mem 0xffe50000-0xffe5e05f] has been reserved [ 0.609194] xen: registering gsi 4 triggering 1 polarity 0 [ 0.609198] Already setup the GSI :4 [ 0.609303] pnp 00:06: [dma 0 disabled] [ 0.609613] xen: registering gsi 3 triggering 1 polarity 0 [ 0.609624] pnp 00:07: [dma 0 disabled] [ 0.609788] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved [ 0.610165] pnp 00:09: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:03:04.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.610359] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.610478] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved [ 0.610602] system 00:09: [mem 0x00100000-0xdfffffff] could not be reserved [ 0.610726] system 00:09: [mem 0xfec00000-0xffffffff] could not be reserved [ 0.611004] pnp: PnP ACPI: found 10 devices [ 0.632668] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.632823] NET: Registered PF_INET protocol family [ 0.632981] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.633397] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.633552] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.633701] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.633857] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.634025] TCP: Hash tables configured (established 4096 bind 4096) [ 0.634239] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.634380] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.634551] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.634850] RPC: Registered named UNIX socket transport module. [ 0.634972] RPC: Registered udp transport module. [ 0.635080] RPC: Registered tcp transport module. [ 0.635198] RPC: Registered tcp-with-tls transport module. [ 0.635309] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.635971] pci 0000:00:09.0: PCI bridge to [bus 01] [ 0.636090] pci 0000:00:09.0: bridge window [io 0xd000-0xdfff] [ 0.636225] pci 0000:00:09.0: bridge window [mem 0xfe900000-0xfe9fffff] [ 0.636360] pci 0000:00:0a.0: PCI bridge to [bus 02] [ 0.636473] pci 0000:00:0a.0: bridge window [io 0xe000-0xefff] [ 0.636595] pci 0000:00:0a.0: bridge window [mem 0xfea00000-0xfeafffff] [ 0.636731] pci 0000:00:14.4: PCI bridge to [bus 03] [ 0.636852] pci 0000:00:14.4: bridge window [mem 0xfdf00000-0xfe7fffff] [ 0.637015] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfcffffff pref] [ 0.637186] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.637302] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.637416] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.637533] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.637650] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.637767] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] [ 0.637878] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] [ 0.637992] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] [ 0.638138] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff] [ 0.638253] pci_bus 0000:03: resource 1 [mem 0xfdf00000-0xfe7fffff] [ 0.638377] pci_bus 0000:03: resource 2 [mem 0xfc000000-0xfcffffff pref] [ 0.638493] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7 window] [ 0.638606] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff window] [ 0.638720] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.638836] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff window] [ 0.638953] pci_bus 0000:03: resource 8 [mem 0xf0000000-0xfebfffff window] [ 0.639227] xen: registering gsi 16 triggering 0 polarity 1 [ 0.639253] xen: --> pirq=16 -> irq=16 (gsi=16) [ 1.302243] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x7c0 took 647543 usecs [ 1.302482] xen: registering gsi 16 triggering 0 polarity 1 [ 1.302489] Already setup the GSI :16 [ 1.326240] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x7c0 took 23261 usecs [ 1.326483] xen: registering gsi 17 triggering 0 polarity 1 [ 1.326527] xen: --> pirq=17 -> irq=17 (gsi=17) [ 1.326712] xen: registering gsi 18 triggering 0 polarity 1 [ 1.326733] xen: --> pirq=18 -> irq=18 (gsi=18) [ 1.350240] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x7c0 took 23034 usecs [ 1.350491] xen: registering gsi 18 triggering 0 polarity 1 [ 1.350499] Already setup the GSI :18 [ 1.374239] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x7c0 took 23251 usecs [ 1.374483] xen: registering gsi 19 triggering 0 polarity 1 [ 1.374522] xen: --> pirq=19 -> irq=19 (gsi=19) [ 1.374730] xen: registering gsi 18 triggering 0 polarity 1 [ 1.374734] Already setup the GSI :18 [ 1.399265] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x7c0 took 24016 usecs [ 1.399491] PCI: CLS 64 bytes, default 64 [ 1.399676] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.399791] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 1.399829] Unpacking initramfs... [ 1.399990] kvm_intel: VMX not supported by CPU 0 [ 1.400177] kvm_amd: SVM not supported by CPU 0 [ 1.400287] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x285c3559aad, max_idle_ns: 440795319783 ns [ 1.401448] clocksource: Switched to clocksource tsc [ 1.472991] Initialise system trusted keyrings [ 1.473208] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 1.473509] NFS: Registering the id_resolver key type [ 1.473620] Key type id_resolver registered [ 1.473745] Key type id_legacy registered [ 1.473930] 9p: Installing v9fs 9p2000 file system support [ 1.491398] Key type asymmetric registered [ 1.491501] Asymmetric key parser 'x509' registered [ 1.491618] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.491772] io scheduler mq-deadline registered [ 1.491874] io scheduler kyber registered [ 1.492363] xen: registering gsi 53 triggering 0 polarity 1 [ 1.492392] xen: --> pirq=53 -> irq=53 (gsi=53) [ 1.492655] xen: registering gsi 54 triggering 0 polarity 1 [ 1.492673] xen: --> pirq=54 -> irq=54 (gsi=54) [ 1.492988] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1.493180] ACPI: button: Power Button [PWRB] [ 1.493339] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.493567] ACPI: button: Power Button [PWRF] [ 1.495817] ACPI: \_PR_.P001: Found 2 idle states [ 1.496088] ACPI: \_PR_.P002: Found 2 idle states [ 1.496234] ACPI: \_PR_.P003: Found 2 idle states [ 1.496385] ACPI: \_PR_.P004: Found 2 idle states [ 1.496950] xen:xen_evtchn: Event-channel device installed [ 1.497210] xen_pciback: backend is vpci [ 1.497961] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.498380] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.500674] hpet_acpi_add: no address or irqs in _CRS [ 1.500843] Non-volatile memory driver v1.3 [ 1.503292] loop: module loaded [ 1.509262] ahci 0000:00:11.0: version 3.0 [ 1.509362] xen: registering gsi 22 triggering 0 polarity 1 [ 1.509391] xen: --> pirq=22 -> irq=22 (gsi=22) [ 1.509539] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 1.509695] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 1.509804] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 1.511028] scsi host0: ahci [ 1.511354] scsi host1: ahci [ 1.511656] scsi host2: ahci [ 1.511982] scsi host3: ahci [ 1.512149] ata1: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd00 irq 22 lpm-pol 0 [ 1.512295] ata2: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbd80 irq 22 lpm-pol 0 [ 1.512477] ata3: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe00 irq 22 lpm-pol 0 [ 1.512621] ata4: SATA max UDMA/133 abar m1024@0xfebfbc00 port 0xfebfbe80 irq 22 lpm-pol 0 [ 1.513212] tun: Universal TUN/TAP device driver, 1.6 [ 1.513450] e100: Intel(R) PRO/100 Network Driver [ 1.513553] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.513672] sky2: driver version 1.30 [ 1.513829] xen_netfront: Initialising Xen virtual ethernet driver [ 1.514196] xen: registering gsi 16 triggering 0 polarity 1 [ 1.514203] Already setup the GSI :16 [ 1.514319] xen: registering gsi 17 triggering 0 polarity 1 [ 1.514325] Already setup the GSI :17 [ 1.514366] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 1.514692] xen: registering gsi 19 triggering 0 polarity 1 [ 1.514696] Already setup the GSI :19 [ 1.514835] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 1.515036] ohci-pci 0000:00:12.0: irq 16, io mem 0xfebf9000 [ 1.551392] Freeing initrd memory: 20192K [ 1.571316] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.571483] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.571623] usb usb1: Product: OHCI PCI host controller [ 1.571729] usb usb1: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.571835] usb usb1: SerialNumber: 0000:00:12.0 [ 1.572202] hub 1-0:1.0: USB hub found [ 1.572314] hub 1-0:1.0: 3 ports detected [ 1.572883] xen: registering gsi 16 triggering 0 polarity 1 [ 1.572890] Already setup the GSI :16 [ 1.572931] ehci-pci 0000:00:12.2: EHCI Host Controller [ 1.573250] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 1.573399] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.573577] ehci-pci 0000:00:12.2: debug port 1 [ 1.573791] ehci-pci 0000:00:12.2: irq 17, io mem 0xfebfb800 [ 1.580095] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 1.580276] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.580460] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.580599] usb usb2: Product: EHCI Host Controller [ 1.580702] usb usb2: Manufacturer: Linux 6.10.0-rc5 ehci_hcd [ 1.580807] usb usb2: SerialNumber: 0000:00:12.2 [ 1.581085] hub 2-0:1.0: USB hub found [ 1.581220] hub 2-0:1.0: 6 ports detected [ 1.633121] hub 1-0:1.0: USB hub found [ 1.633237] hub 1-0:1.0: 3 ports detected [ 1.633552] ehci-pci 0000:00:13.2: EHCI Host Controller [ 1.633800] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 1.633944] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.634126] ehci-pci 0000:00:13.2: debug port 1 [ 1.634319] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfb400 [ 1.641098] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.641379] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 1.641531] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.641671] usb usb3: Product: EHCI Host Controller [ 1.641775] usb usb3: Manufacturer: Linux 6.10.0-rc5 ehci_hcd [ 1.641881] usb usb3: SerialNumber: 0000:00:13.2 [ 1.642149] hub 3-0:1.0: USB hub found [ 1.642284] hub 3-0:1.0: 6 ports detected [ 1.642640] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 1.642863] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 1.643042] ohci-pci 0000:00:12.1: irq 16, io mem 0xfebfa000 [ 1.699223] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.699376] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.699515] usb usb4: Product: OHCI PCI host controller [ 1.699623] usb usb4: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.699768] usb usb4: SerialNumber: 0000:00:12.1 [ 1.700066] hub 4-0:1.0: USB hub found [ 1.700191] hub 4-0:1.0: 3 ports detected [ 1.700744] xen: registering gsi 18 triggering 0 polarity 1 [ 1.700749] Already setup the GSI :18 [ 1.700901] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 1.701159] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 1.701358] ohci-pci 0000:00:13.0: irq 18, io mem 0xfebf7000 [ 1.757325] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.757478] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.757618] usb usb5: Product: OHCI PCI host controller [ 1.757741] usb usb5: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.757856] usb usb5: SerialNumber: 0000:00:13.0 [ 1.758191] hub 5-0:1.0: USB hub found [ 1.758384] hub 5-0:1.0: 3 ports detected [ 1.758877] xen: registering gsi 18 triggering 0 polarity 1 [ 1.758882] Already setup the GSI :18 [ 1.759018] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 1.759248] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 1.759427] ohci-pci 0000:00:13.1: irq 18, io mem 0xfebf8000 [ 1.815359] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.815512] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.815652] usb usb6: Product: OHCI PCI host controller [ 1.815770] usb usb6: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.815877] usb usb6: SerialNumber: 0000:00:13.1 [ 1.816245] hub 6-0:1.0: USB hub found [ 1.816383] hub 6-0:1.0: 3 ports detected [ 1.816852] xen: registering gsi 18 triggering 0 polarity 1 [ 1.816857] Already setup the GSI :18 [ 1.817019] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 1.817220] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 1.817392] ohci-pci 0000:00:14.5: irq 18, io mem 0xfebf6000 [ 1.824020] ata4: SATA link down (SStatus 0 SControl 300) [ 1.824222] ata3: SATA link down (SStatus 0 SControl 300) [ 1.873301] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.10 [ 1.873453] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.873593] usb usb7: Product: OHCI PCI host controller [ 1.873697] usb usb7: Manufacturer: Linux 6.10.0-rc5 ohci_hcd [ 1.873803] usb usb7: SerialNumber: 0000:00:14.5 [ 1.874155] hub 7-0:1.0: USB hub found [ 1.874326] hub 7-0:1.0: 2 ports detected [ 1.874824] usbcore: registered new interface driver usblp [ 1.874954] usbcore: registered new interface driver usb-storage [ 1.875116] i8042: PNP: No PS/2 controller found. [ 1.875219] i8042: Probing ports directly. [ 1.878093] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.878202] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.878561] rtc_cmos 00:02: RTC can wake from S4 [ 1.879128] rtc_cmos 00:02: registered as rtc0 [ 1.879305] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram [ 1.879462] device-mapper: uevent: version 1.0.3 [ 1.879642] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.879794] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 1.879989] hid: raw HID events driver (C) Jiri Kosina [ 1.880325] usbcore: registered new interface driver usbhid [ 1.880431] usbhid: USB HID core driver [ 1.880954] Initializing XFRM netlink socket [ 1.881103] NET: Registered PF_INET6 protocol family [ 1.881832] Segment Routing with IPv6 [ 1.881947] In-situ OAM (IOAM) with IPv6 [ 1.882129] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.882393] NET: Registered PF_PACKET protocol family [ 1.882526] 9pnet: Installing 9P2000 support [ 1.882683] Key type dns_resolver registered [ 1.882800] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 1.883373] IPI shorthand broadcast: enabled [ 1.887806] sched_clock: Marking stable (1862003632, 25043015)->(1895596747, -8550100) [ 1.888379] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.888705] registered taskstats version 1 [ 1.888806] Loading compiled-in X.509 certificates [ 1.890987] PM: Magic number: 12:582:275 [ 1.891118] usb usb1-port3: hash matches [ 1.891244] tty tty12: hash matches [ 1.891367] printk: legacy console [netcon0] enabled [ 1.891496] netconsole: network logging started [ 1.891693] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 1.902232] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 1.902630] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 1.904357] ALSA device list: [ 1.904455] No soundcards found. [ 1.905258] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 1.978115] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.978266] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.978966] ata2.00: ATA-9: WDC WD1003FZEX-00MK2A0, 01.01A01, max UDMA/133 [ 1.979539] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 1.979840] ata1.00: ATA-8: WDC WD1003FBYZ-010FB0, 01.01V03, max UDMA/133 [ 1.980287] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 1.980567] ata2.00: configured for UDMA/133 [ 1.982070] ata1.00: configured for UDMA/133 [ 1.982345] scsi 0:0:0:0: Direct-Access ATA WDC WD1003FBYZ-0 1V03 PQ: 0 ANSI: 5 [ 1.982943] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.983006] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.983256] sd 0:0:0:0: [sda] Write Protect is off [ 1.983370] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.983400] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.983412] scsi 1:0:0:0: Direct-Access ATA WDC WD1003FZEX-0 1A01 PQ: 0 ANSI: 5 [ 1.983695] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 1.984429] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 1.984479] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.984698] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 1.984825] sd 1:0:0:0: [sdb] Write Protect is off [ 1.984930] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1.984952] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.985162] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 2.010321] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.013941] sda: sda1 sda2 < sda5 > [ 2.014318] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.016379] Freeing unused kernel image (initmem) memory: 2680K [ 2.016513] Write protecting the kernel read-only data: 24576k [ 2.028956] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 2.130074] usb 6-2: new full-speed USB device number 2 using ohci-pci [ 2.144146] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 2.144264] Run /init as init process [ 2.144376] with arguments: [ 2.144378] /init [ 2.144379] placeholder [ 2.144381] with environment: [ 2.144382] HOME=/ [ 2.144383] TERM=linux [ 2.298202] usb 6-2: New USB device found, idVendor=0557, idProduct=2221, bcdDevice= 0.01 [ 2.298390] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.298504] usb 6-2: Product: Hermon USB hidmouse Device [ 2.298610] usb 6-2: Manufacturer: Winbond Electronics Corp [ 2.304698] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.0/0003:0557:2221.0001/input/input5 [ 2.305100] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input0 [ 2.308757] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:13.1/usb6/6-2/6-2:1.1/0003:0557:2221.0002/input/input6 [ 2.360458] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:13.1-2/input1 [ 2.415339] e1000e: Intel(R) PRO/1000 Network Driver [ 2.415465] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.415718] xen: registering gsi 48 triggering 0 polarity 1 [ 2.415754] xen: --> pirq=48 -> irq=48 (gsi=48) [ 2.415981] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.461058] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.504898] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e8:ac [ 2.505062] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.505262] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.505536] xen: registering gsi 47 triggering 0 polarity 1 [ 2.505569] xen: --> pirq=47 -> irq=47 (gsi=47) [ 2.505760] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.552120] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock [ 2.599088] e1000e 0000:02:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 00:25:90:ae:e8:ad [ 2.599247] e1000e 0000:02:00.0 eth1: Intel(R) PRO/1000 Network Connection [ 2.599448] e1000e 0000:02:00.0 eth1: MAC: 3, PHY: 8, PBA No: 0100FF-0FF [ 2.601478] e1000e 0000:01:00.0 enx002590aee8ac: renamed from eth0 [ 2.602041] e1000e 0000:02:00.0 enx002590aee8ad: renamed from eth1 [ 2.616119] random: crng init done [ 3.319660] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.326306] EXT4-fs (dm-0): mounted filesystem 2758660d-6ca4-4f6b-a138-a3e53057d268 ro with ordered data mode. Quota mode: none. [ 7.488447] EXT4-fs (dm-0): re-mounted 2758660d-6ca4-4f6b-a138-a3e53057d268 r/w. Quota mode: none. [ 8.917683] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 8.938035] EXT4-fs (sda1): mounted filesystem 72a38c90-e83d-42be-96ce-6aa7461a5216 r/w with ordered data mode. Quota mode: none. [ 9.018090] Adding 1949692k swap on /dev/mapper/pinot0--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 10.578388] xenbr0: port 1(enx002590aee8ac) entered blocking state [ 10.578527] xenbr0: port 1(enx002590aee8ac) entered disabled state [ 10.578659] e1000e 0000:01:00.0 enx002590aee8ac: entered allmulticast mode [ 10.578815] e1000e 0000:01:00.0 enx002590aee8ac: entered promiscuous mode [ 13.731114] e1000e 0000:01:00.0 enx002590aee8ac: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 13.731659] xenbr0: port 1(enx002590aee8ac) entered blocking state [ 13.731770] xenbr0: port 1(enx002590aee8ac) entered forwarding state