[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod0) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Tue Jun 25 11:52:20 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6084K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000521] Console: colour dummy device 80x30 [ 0.000539] printk: legacy console [hvc0] enabled [ 0.299188] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309587] CPU: Testing write buffer coherency: ok [ 0.314530] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.324083] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330496] pid_max: default: 32768 minimum: 301 [ 0.335284] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342584] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350959] /cpus/cpu@0 missing clock-frequency property [ 0.355767] /cpus/cpu@1 missing clock-frequency property [ 0.361160] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367869] xen:grant_table: Grant tables using version 1 layout [ 0.373019] Grant table initialized [ 0.376573] xen:events: Using FIFO-based ABI [ 0.380869] Xen: initializing cpu0 [ 0.384392] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392159] rcu: Hierarchical SRCU implementation. [ 0.395788] rcu: Max phase no-delay instances is 1000. [ 0.404012] EFI services will not be available. [ 0.407339] smp: Bringing up secondary CPUs ... [ 0.481630] Xen: initializing cpu1 [ 0.481792] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481816] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500782] smp: Brought up 1 node, 2 CPUs [ 0.504443] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510731] CPU: All CPU(s) started in SVC mode. [ 0.516656] devtmpfs: initialized [ 0.529223] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535776] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545446] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553351] pinctrl core: initialized pinctrl subsystem [ 0.559970] DMI not present or invalid. [ 0.563478] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.570095] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579482] thermal_sys: Registered thermal governor 'step_wise' [ 0.579642] software IO TLB: area num 2. [ 0.588318] software IO TLB: only able to allocate 8 MB [ 0.595390] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600593] No ATAGs? [ 0.602897] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611649] Serial: AMBA PL011 UART driver [ 0.658277] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686757] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.710409] xen:balloon: Initialising balloon driver [ 0.716853] iommu: Default domain type: Translated [ 0.720272] iommu: DMA domain TLB invalidation policy: strict mode [ 0.729061] SCSI subsystem initialized [ 0.731596] libata version 3.00 loaded. [ 0.731827] usbcore: registered new interface driver usbfs [ 0.737048] usbcore: registered new interface driver hub [ 0.742401] usbcore: registered new device driver usb [ 0.749100] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.752687] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.758953] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.764008] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.768938] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.774978] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.780777] pps_core: LinuxPPS API ver. 1 registered [ 0.785146] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.794377] PTP clock support registered [ 0.798609] EDAC MC: Ver: 3.0.0 [ 0.801870] scmi_core: SCMI protocol bus registered [ 0.816772] vgaarb: loaded [ 0.819965] clocksource: Switched to clocksource arch_sys_counter [ 0.834331] NET: Registered PF_INET protocol family [ 0.837972] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.845901] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.853570] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.861374] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.869215] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.876497] TCP: Hash tables configured (established 4096 bind 4096) [ 0.882860] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.889427] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.896538] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.902687] RPC: Registered named UNIX socket transport module. [ 0.908142] RPC: Registered udp transport module. [ 0.912936] RPC: Registered tcp transport module. [ 0.917690] RPC: Registered tcp-with-tls transport module. [ 0.923258] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.929760] PCI: CLS 0 bytes, default 64 [ 0.935201] Initialise system trusted keyrings [ 0.938485] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.945038] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.950935] Trying to unpack rootfs image as initramfs... [ 1.001330] NFS: Registering the id_resolver key type [ 1.005038] Key type id_resolver registered [ 1.009285] Key type id_legacy registered [ 1.013397] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.020140] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.051430] Key type asymmetric registered [ 1.054158] Asymmetric key parser 'x509' registered [ 1.059182] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.066609] io scheduler mq-deadline registered [ 1.071186] io scheduler kyber registered [ 1.075271] io scheduler bfq registered [ 1.202839] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.209067] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.241824] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.248026] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.281997] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.288198] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.321978] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.328177] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.340611] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.354374] xen:xen_evtchn: Event-channel device installed [ 1.426568] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.449069] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.475389] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.494358] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.511535] SuperH (H)SCI(F) driver initialized [ 1.515127] STMicroelectronics ASC driver initialized [ 1.520038] STM32 USART driver initialized [ 1.551404] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.564082] random: crng init done [ 1.629029] Freeing initrd memory: 11856K [ 1.635513] brd: module loaded [ 1.641683] loop: module loaded [ 1.657432] Invalid max_queues (4), will use default max: 2. [ 1.676459] tun: Universal TUN/TAP device driver, 1.6 [ 1.680331] CAN device driver interface [ 1.685427] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.696658] xen_netfront: Initialising Xen virtual ethernet driver [ 1.701530] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.707129] usbcore: registered new interface driver pegasus [ 1.712871] usbcore: registered new interface driver asix [ 1.718351] usbcore: registered new interface driver ax88179_178a [ 1.724505] usbcore: registered new interface driver cdc_ether [ 1.730402] usbcore: registered new interface driver smsc75xx [ 1.736205] usbcore: registered new interface driver smsc95xx [ 1.742072] usbcore: registered new interface driver net1080 [ 1.747758] usbcore: registered new interface driver cdc_subset [ 1.753779] usbcore: registered new interface driver zaurus [ 1.759404] usbcore: registered new interface driver cdc_ncm [ 1.768913] usbcore: registered new interface driver usb-storage [ 1.779514] i2c_dev: i2c /dev entries driver [ 1.798240] device-mapper: uevent: version 1.0.3 [ 1.801715] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.811281] cpu cpu0: OPP table can't be empty [ 1.815981] failed to register cpuidle driver [ 1.819371] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.827734] sdhci: Secure Digital Host Controller Interface driver [ 1.832749] sdhci: Copyright(c) Pierre Ossman [ 1.840860] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.848638] ledtrig-cpu: registered to indicate activity on CPUs [ 1.854090] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.860756] usbcore: registered new interface driver usbhid [ 1.865415] usbhid: USB HID core driver [ 1.876338] NET: Registered PF_INET6 protocol family [ 1.880974] Segment Routing with IPv6 [ 1.883686] In-situ OAM (IOAM) with IPv6 [ 1.887709] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.894157] NET: Registered PF_PACKET protocol family [ 1.898801] can: controller area network core [ 1.903263] NET: Registered PF_CAN protocol family [ 1.908054] can: raw protocol [ 1.911107] can: broadcast manager protocol [ 1.915349] can: netlink gateway - max_hops=1 [ 1.920123] Key type dns_resolver registered [ 1.924779] ThumbEE CPU extension supported. [ 1.928456] Registering SWP/SWPB emulation handler [ 1.942986] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.949870] Loading compiled-in X.509 certificates [ 1.993896] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.997495] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.004345] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.012301] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.053858] s5m-rtc s5m-rtc: registered as rtc0 [ 2.062722] s5m-rtc s5m-rtc: setting system clock to 2024-06-25T15:13:46 UTC (1719328426) [ 2.073781] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.078388] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.082804] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.089510] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.095430] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.101632] clk: Not disabling unused clocks [ 2.105105] PM: genpd: Disabling unused power domains [ 2.113674] Freeing unused kernel image (initmem) memory: 2048K [ 2.120045] Run /init as init process [ 2.122347] with arguments: [ 2.122353] /init [ 2.122360] with environment: [ 2.122365] HOME=/ [ 2.122370] TERM=linux [ 3.550677] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.557859] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.558395] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.580030] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.585654] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.591237] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.605481] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.633592] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.650999] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.657344] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.657379] Synopsys Designware Multimedia Card Interface Driver [ 3.664682] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.710265] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.750265] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.755981] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.764816] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.771670] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.888688] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.894458] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.894729] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.912059] scsi host0: ahci-dwc [ 3.912708] hub 1-0:1.0: USB hub found [ 3.914296] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 126 lpm-pol 0 [ 3.917779] hub 1-0:1.0: 3 ports detected [ 3.950596] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.956035] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.965281] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.978070] mmc_host mmc0: card is polling. [ 4.014981] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 4.020607] exynos-ohci 12120000.usb: USB Host Controller [ 4.026062] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 4.051822] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.060168] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 4.066218] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.072563] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.078082] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 128,32 bit host data width,128 deep fifo [ 4.100667] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.150191] hub 2-0:1.0: USB hub found [ 4.153229] hub 2-0:1.0: 3 ports detected [ 4.176691] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.182108] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.202260] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.212370] mmc0: new DDR MMC card at address 0001 [ 4.217323] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.230012] mmcblk0: p1 p2 p3 p4 [ 4.234069] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.240073] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.246859] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.293529] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.307603] mmc1: new high speed SDHC card at address aaaa [ 4.313742] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.530904] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.538516] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.543894] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.552768] ata1.00: configured for UDMA/133 [ 4.556234] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.571658] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.577799] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.583557] sd 0:0:0:0: [sda] Write Protect is off [ 4.587951] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.588036] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.597208] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.617549] sda: sda1 sda2 < sda5 > [ 4.620537] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.646574] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.654579] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.658724] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.705869] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.714122] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.720253] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.725602] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.733313] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.750702] hub 3-0:1.0: USB hub found [ 4.769815] hub 3-0:1.0: 1 port detected [ 4.775572] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.783491] hub 4-0:1.0: USB hub found [ 4.786481] hub 4-0:1.0: 1 port detected [ 4.906777] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.078952] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.187636] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.295887] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.404003] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.512203] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.620311] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.728385] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.836476] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.944575] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.353331] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.461078] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 7.069405] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 10.556270] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 10.868851] EXT4-fs (dm-0): mounted filesystem 72d4ea96-e19b-4cc4-a555-3e9ece2c0b08 ro with ordered data mode. Quota mode: disabled. [ 14.756223] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 14.758140] s5p-secss 10830000.sss: s5p-sss driver registered [ 14.788986] mc: Linux media interface: v0.10 [ 14.896590] videodev: Linux video capture interface: v2.00 [ 15.062531] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 15.094175] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.135460] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.151597] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.158978] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.160118] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.180113] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 15.186270] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 15.334911] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 15.342432] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 15.351231] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 15.358691] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 15.364051] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.469986] usb3503 usb-hub: switched to HUB mode [ 15.473334] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.476915] blk_print_req_error: 6 callbacks suppressed [ 15.476928] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.598844] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.710372] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.822914] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.900005] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 15.907277] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 15.931101] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.981793] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 15.997192] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 16.042046] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.104792] hub 1-3:1.0: USB hub found [ 16.109609] hub 1-3:1.0: 3 ports detected [ 16.153027] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.263786] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.352624] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.360339] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.369004] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.379822] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.388641] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.397319] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.430190] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.582685] hub 1-3.2:1.0: USB hub found [ 16.585629] hub 1-3.2:1.0: 4 ports detected [ 16.672738] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 16.708252] usbcore: registered new device driver onboard-usb-dev [ 16.780546] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 16.832830] hub 1-3.2:1.0: USB hub found [ 16.835774] hub 1-3.2:1.0: 4 ports detected [ 16.848978] hub 1-3.2:1.0: USB hub found [ 16.851991] hub 1-3.2:1.0: 4 ports detected [ 17.060011] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.213748] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.388966] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 17.891856] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 17.906228] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 17.916086] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 6a:90:f5:8a:b2:95 [ 18.617528] EXT4-fs (dm-0): re-mounted 72d4ea96-e19b-4cc4-a555-3e9ece2c0b08 r/w. Quota mode: disabled. [ 20.008627] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.057311] EXT4-fs (sda1): mounted filesystem 73aa37bc-25ad-4f2b-99f8-ab9a0f0f2ba3 r/w with ordered data mode. Quota mode: disabled. [ 20.152700] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 22.569665] xenbr0: port 1(eth0) entered blocking state [ 22.573577] xenbr0: port 1(eth0) entered disabled state [ 22.578843] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 22.584714] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 22.595226] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.807106] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 24.813184] xenbr0: port 1(eth0) entered blocking state [ 24.818362] xenbr0: port 1(eth0) entered forwarding state [ 26.881921] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed