[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.95+ (osstest@fiano0) (arm-linux-gnueabihf-gcc (Debian 8.3.0-2) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1 SMP Wed Jun 26 15:12:08 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.17 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 16 pages/cpu s35412 r8192 d21932 u65536 [ 0.000000] pcpu-alloc: s35412 r8192 d21932 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=hvc0 net.ifnames=0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 418284K/524288K available (13312K kernel code, 2179K rwdata, 5636K rodata, 2048K init, 435K bss, 40468K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000012] Switching to timer-based delay loop, resolution 41ns [ 0.000510] Console: colour dummy device 80x30 [ 0.293929] printk: console [hvc0] enabled [ 0.298122] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.308521] CPU: Testing write buffer coherency: ok [ 0.313462] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.323016] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.329430] pid_max: default: 32768 minimum: 301 [ 0.334225] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.341514] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.349899] /cpus/cpu@0 missing clock-frequency property [ 0.354700] /cpus/cpu@1 missing clock-frequency property [ 0.360095] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.366610] xen:grant_table: Grant tables using version 1 layout [ 0.371960] Grant table initialized [ 0.375481] xen:events: Using FIFO-based ABI [ 0.379798] Xen: initializing cpu0 [ 0.383324] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.391088] rcu: Hierarchical SRCU implementation. [ 0.394718] rcu: Max phase no-delay instances is 1000. [ 0.402845] EFI services will not be available. [ 0.406144] smp: Bringing up secondary CPUs ... [ 0.481371] Xen: initializing cpu1 [ 0.481510] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481532] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500392] smp: Brought up 1 node, 2 CPUs [ 0.504176] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510482] CPU: All CPU(s) started in SVC mode. [ 0.515836] devtmpfs: initialized [ 0.528307] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.534784] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.544511] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.552699] pinctrl core: initialized pinctrl subsystem [ 0.559073] DMI not present or invalid. [ 0.562158] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569533] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.578246] thermal_sys: Registered thermal governor 'step_wise' [ 0.578560] software IO TLB: area num 2. [ 0.587225] software IO TLB: only able to allocate 8 MB [ 0.594345] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.599525] No ATAGs? [ 0.601853] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.610356] Serial: AMBA PL011 UART driver [ 0.632502] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 62 [ 0.681888] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.706071] xen:balloon: Initialising balloon driver [ 0.713797] iommu: Default domain type: Translated [ 0.717295] iommu: DMA domain TLB invalidation policy: strict mode [ 0.724248] SCSI subsystem initialized [ 0.727606] libata version 3.00 loaded. [ 0.727792] usbcore: registered new interface driver usbfs [ 0.733063] usbcore: registered new interface driver hub [ 0.738435] usbcore: registered new device driver usb [ 0.745119] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.748723] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.755032] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.763474] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.772609] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.778130] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.782835] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.789057] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.794293] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.799069] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.805181] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.810361] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.815279] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.821314] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.827106] pps_core: LinuxPPS API ver. 1 registered [ 0.831521] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.840722] PTP clock support registered [ 0.844911] EDAC MC: Ver: 3.0.0 [ 0.850239] vgaarb: loaded [ 0.856724] clocksource: Switched to clocksource arch_sys_counter [ 0.879020] NET: Registered PF_INET protocol family [ 0.882649] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.890607] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.898254] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.906049] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.913913] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.921177] TCP: Hash tables configured (established 4096 bind 4096) [ 0.927548] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.934092] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.941232] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.947698] RPC: Registered named UNIX socket transport module. [ 0.952847] RPC: Registered udp transport module. [ 0.957626] RPC: Registered tcp transport module. [ 0.962375] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.968898] PCI: CLS 0 bytes, default 64 [ 0.974431] Initialise system trusted keyrings [ 0.977772] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.979577] Trying to unpack rootfs image as initramfs... [ 0.991661] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.020147] NFS: Registering the id_resolver key type [ 1.023849] Key type id_resolver registered [ 1.028108] Key type id_legacy registered [ 1.032283] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.038962] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.067227] Key type asymmetric registered [ 1.069950] Asymmetric key parser 'x509' registered [ 1.075019] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.082424] io scheduler mq-deadline registered [ 1.086992] io scheduler kyber registered [ 1.128680] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.241222] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.247446] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.283913] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.290144] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.325677] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.331904] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.361412] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.367662] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.381984] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.392476] xen:xen_evtchn: Event-channel device installed [ 1.441438] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.450225] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 113, base_baud = 0) is a S3C6400/10 [ 1.458323] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 114, base_baud = 0) is a S3C6400/10 [ 1.467380] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 115, base_baud = 0) is a S3C6400/10 [ 1.476655] SuperH (H)SCI(F) driver initialized [ 1.481560] STMicroelectronics ASC driver initialized [ 1.486955] STM32 USART driver initialized [ 1.491591] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.521144] brd: module loaded [ 1.528284] loop: module loaded [ 1.553435] Freeing initrd memory: 11368K [ 1.569666] Invalid max_queues (4), will use default max: 2. [ 1.596289] tun: Universal TUN/TAP device driver, 1.6 [ 1.600193] CAN device driver interface [ 1.605330] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.616018] xen_netfront: Initialising Xen virtual ethernet driver [ 1.620910] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.626488] usbcore: registered new interface driver pegasus [ 1.632233] usbcore: registered new interface driver asix [ 1.637695] usbcore: registered new interface driver ax88179_178a [ 1.643857] usbcore: registered new interface driver cdc_ether [ 1.649767] usbcore: registered new interface driver smsc75xx [ 1.655574] usbcore: registered new interface driver smsc95xx [ 1.661392] usbcore: registered new interface driver net1080 [ 1.667128] usbcore: registered new interface driver cdc_subset [ 1.673091] usbcore: registered new interface driver zaurus [ 1.678770] usbcore: registered new interface driver cdc_ncm [ 1.688152] usbcore: registered new interface driver usb-storage [ 1.722247] s5m-rtc s5m-rtc: registered as rtc0 [ 1.730974] s5m-rtc s5m-rtc: setting system clock to 2024-06-26T19:56:05 UTC (1719431765) [ 1.739614] i2c_dev: i2c /dev entries driver [ 1.750058] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed for psci_sys_poweroff [ 1.759754] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 1.771046] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 1.781972] device-mapper: uevent: version 1.0.3 [ 1.785445] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 1.794466] cpu cpu0: OPP table can't be empty [ 1.799654] failed to register cpuidle driver [ 1.802664] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.811255] sdhci: Secure Digital Host Controller Interface driver [ 1.816064] sdhci: Copyright(c) Pierre Ossman [ 1.824636] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.849239] ledtrig-cpu: registered to indicate activity on CPUs [ 1.855579] usbcore: registered new interface driver usbhid [ 1.859865] usbhid: USB HID core driver [ 1.870919] NET: Registered PF_INET6 protocol family [ 1.875560] Segment Routing with IPv6 [ 1.878303] In-situ OAM (IOAM) with IPv6 [ 1.882292] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.888690] NET: Registered PF_PACKET protocol family [ 1.893361] can: controller area network core [ 1.897851] NET: Registered PF_CAN protocol family [ 1.902630] can: raw protocol [ 1.905670] can: broadcast manager protocol [ 1.909971] can: netlink gateway - max_hops=1 [ 1.914588] Key type dns_resolver registered [ 1.919568] ThumbEE CPU extension supported. [ 1.923034] Registering SWP/SWPB emulation handler [ 1.928389] Loading compiled-in X.509 certificates [ 1.956630] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 1.962704] clk: Not disabling unused clocks [ 1.969454] Freeing unused kernel image (initmem) memory: 2048K [ 1.975521] Run /init as init process [ 1.977836] with arguments: [ 1.977842] /init [ 1.977848] with environment: [ 1.977853] HOME=/ [ 1.977858] TERM=linux [ 2.998172] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.032144] phy phy-12130000.phy.7: phy_power_on was called before phy_init [ 3.037803] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.037845] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.043308] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.051873] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.069420] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.099072] Synopsys Designware Multimedia Card Interface Driver [ 3.104331] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.111536] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.116300] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.118820] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.136340] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.136374] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.169291] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.169367] hub 1-0:1.0: USB hub found [ 3.174358] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.183723] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.193539] mmc_host mmc0: card is polling. [ 3.196733] hub 1-0:1.0: 3 ports detected [ 3.203969] phy phy-12130000.phy.7: phy_power_on was called before phy_init [ 3.209986] exynos-ohci 12120000.usb: USB Host Controller [ 3.215084] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.222813] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.237442] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.237578] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.242522] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.249669] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.249683] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.255190] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.297941] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.323392] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.336193] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.336463] scsi host0: ahci-dwc [ 3.353711] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 [ 3.416214] hub 2-0:1.0: USB hub found [ 3.430489] hub 2-0:1.0: 3 ports detected [ 3.440166] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 3.456834] mmc1: new high speed SDHC card at address aaaa [ 3.461564] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 3.471027] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.477615] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.486018] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.496749] mmc0: new DDR MMC card at address 0001 [ 3.501433] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 3.509089] mmcblk0: p1 p2 p3 p4 [ 3.517171] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 3.523878] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 3.530011] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 3.856785] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.862490] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 3.868446] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 3.876067] ata1.00: configured for UDMA/133 [ 3.879772] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 3.888895] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 3.895031] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 3.900511] sd 0:0:0:0: [sda] Write Protect is off [ 3.905181] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 3.905295] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.914460] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 3.936372] sda: sda1 sda2 < sda5 > [ 3.939183] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.947267] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 3.976152] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 3.983162] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 3.987520] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.034057] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 4.042574] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.048397] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.053762] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.061520] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.069474] hub 3-0:1.0: USB hub found [ 4.072261] hub 3-0:1.0: 1 port detected [ 4.077264] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.085043] hub 4-0:1.0: USB hub found [ 4.091716] hub 4-0:1.0: 1 port detected [ 4.186792] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.258805] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.392415] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 4.500600] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 4.608786] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 4.716969] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 5.056293] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.130960] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.245260] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 5.353000] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 5.460732] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 5.481225] Buffer I/O error on dev mmcblk1, logical block 967954, async page read [ 10.596727] random: crng init done [ 11.397619] process '/usr/bin/fstype' started with executable stack [ 11.844156] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.211205] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: disabled. [ 14.455718] systemd-udevd[304]: Network interface NamePolicy= disabled on kernel command line, ignoring. [ 14.718001] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.723363] wm8994: probe of 3-001a failed with error -22 [ 15.827501] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.862746] mc: Linux media interface: v0.10 [ 15.877340] s5p-secss 10830000.sss: s5p-sss driver registered [ 15.935674] videodev: Linux video capture interface: v2.00 [ 16.103676] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 16.120565] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 16.171783] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.185059] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.192450] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.217605] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 16.223320] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 16.246851] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.322644] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.391096] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 16.399498] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 16.404512] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 16.410339] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 16.467405] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.506733] usb3503 usb-hub: switched to HUB mode [ 16.510086] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.577302] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.626912] systemd-udevd[323]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 16.627181] systemd-udevd[318]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 16.685470] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.759191] systemd-udevd[323]: Process 'ifupdown-hotplug' failed with exit code 1. [ 16.765976] systemd-udevd[318]: Process 'ifupdown-hotplug' failed with exit code 1. [ 16.793705] I/O error, dev mmcblk1, sector 7743639 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2 [ 16.832648] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 16.876790] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.974076] I/O error, dev mmcblk1, sector 7743714 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 2 [ 17.077870] hub 1-3:1.0: USB hub found [ 17.081089] hub 1-3:1.0: 3 ports detected [ 17.254535] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.262248] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.270952] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.281858] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 17.291832] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.300036] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.308774] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.369864] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 17.416748] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.484204] I/O error, dev mmcblk1, sector 7743636 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.569364] hub 1-3.2:1.0: USB hub found [ 17.572207] hub 1-3.2:1.0: 4 ports detected [ 17.591955] I/O error, dev mmcblk1, sector 7743637 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.600748] usbcore: registered new device driver onboard-usb-hub [ 17.699719] I/O error, dev mmcblk1, sector 7743638 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.719794] Buffer I/O error on dev mmcblk1, logical block 967954, async page read [ 17.737515] hub 1-3.2:1.0: USB hub found [ 17.740617] hub 1-3.2:1.0: 4 ports detected [ 17.751356] hub 1-3.2:1.0: USB hub found [ 17.754337] hub 1-3.2:1.0: 4 ports detected [ 18.076796] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 18.229840] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.292213] EXT4-fs (dm-0): re-mounted. Quota mode: disabled. [ 18.928706] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.943204] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.953041] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, ee:5d:95:bc:dc:66 [ 18.989175] systemd-udevd[323]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 18.999108] systemd-udevd[323]: Could not generate persistent MAC address for eth0: No such file or directory [ 19.269446] systemd-udevd[323]: Process 'ifupdown-hotplug' failed with exit code 1. [ 21.350295] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.401085] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: disabled. [ 21.556930] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 22.434814] systemd-udevd[323]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 22.444675] systemd-udevd[323]: Could not generate persistent MAC address for xenbr0: No such file or directory [ 22.455398] xenbr0: port 1(eth0) entered blocking state [ 22.459837] xenbr0: port 1(eth0) entered disabled state [ 22.465223] device eth0 entered promiscuous mode [ 22.475709] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 22.481595] systemd-udevd[323]: Process 'ifupdown-hotplug' failed with exit code 1.