[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.95+ (osstest@fiano0) (arm-linux-gnueabihf-gcc (Debian 8.3.0-2) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1 SMP Wed Jun 26 15:12:08 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.17 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 16 pages/cpu s35412 r8192 d21932 u65536 [ 0.000000] pcpu-alloc: s35412 r8192 d21932 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 net.ifnames=0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 418284K/524288K available (13312K kernel code, 2179K rwdata, 5636K rodata, 2048K init, 435K bss, 40468K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000504] Console: colour dummy device 80x30 [ 0.293576] printk: console [hvc0] enabled [ 0.297768] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.308167] CPU: Testing write buffer coherency: ok [ 0.313109] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.322663] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.329076] pid_max: default: 32768 minimum: 301 [ 0.333872] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.341161] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.349543] /cpus/cpu@0 missing clock-frequency property [ 0.354347] /cpus/cpu@1 missing clock-frequency property [ 0.359740] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.366259] xen:grant_table: Grant tables using version 1 layout [ 0.371585] Grant table initialized [ 0.375130] xen:events: Using FIFO-based ABI [ 0.379446] Xen: initializing cpu0 [ 0.382972] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.390734] rcu: Hierarchical SRCU implementation. [ 0.394365] rcu: Max phase no-delay instances is 1000. [ 0.402488] EFI services will not be available. [ 0.405793] smp: Bringing up secondary CPUs ... [ 0.481069] Xen: initializing cpu1 [ 0.481228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481250] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500088] smp: Brought up 1 node, 2 CPUs [ 0.503874] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510180] CPU: All CPU(s) started in SVC mode. [ 0.515545] devtmpfs: initialized [ 0.527977] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.534456] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.544182] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.552346] pinctrl core: initialized pinctrl subsystem [ 0.558751] DMI not present or invalid. [ 0.561847] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569211] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.577923] thermal_sys: Registered thermal governor 'step_wise' [ 0.578237] software IO TLB: area num 2. [ 0.586911] software IO TLB: only able to allocate 8 MB [ 0.594023] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.599205] No ATAGs? [ 0.601535] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.610034] Serial: AMBA PL011 UART driver [ 0.632178] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 62 [ 0.681581] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.705761] xen:balloon: Initialising balloon driver [ 0.713479] iommu: Default domain type: Translated [ 0.716977] iommu: DMA domain TLB invalidation policy: strict mode [ 0.723928] SCSI subsystem initialized [ 0.727289] libata version 3.00 loaded. [ 0.727475] usbcore: registered new interface driver usbfs [ 0.732743] usbcore: registered new interface driver hub [ 0.738116] usbcore: registered new device driver usb [ 0.744802] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.748413] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.754719] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.763164] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.772300] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.777821] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.782524] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.788754] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.793984] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.798760] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.804870] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.810052] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.814970] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.821003] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.826799] pps_core: LinuxPPS API ver. 1 registered [ 0.831210] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.840411] PTP clock support registered [ 0.844603] EDAC MC: Ver: 3.0.0 [ 0.849917] vgaarb: loaded [ 0.856467] clocksource: Switched to clocksource arch_sys_counter [ 0.878770] NET: Registered PF_INET protocol family [ 0.882401] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.890356] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.898004] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.905799] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.913663] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.920928] TCP: Hash tables configured (established 4096 bind 4096) [ 0.927298] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.933844] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.940983] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.947450] RPC: Registered named UNIX socket transport module. [ 0.952597] RPC: Registered udp transport module. [ 0.957378] RPC: Registered tcp transport module. [ 0.962126] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.968650] PCI: CLS 0 bytes, default 64 [ 0.974173] Initialise system trusted keyrings [ 0.977464] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.979380] Trying to unpack rootfs image as initramfs... [ 0.991405] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.020024] NFS: Registering the id_resolver key type [ 1.023728] Key type id_resolver registered [ 1.027986] Key type id_legacy registered [ 1.032159] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.038846] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.085953] Key type asymmetric registered [ 1.088695] Asymmetric key parser 'x509' registered [ 1.093748] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.101119] io scheduler mq-deadline registered [ 1.105689] io scheduler kyber registered [ 1.142097] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.249248] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.255453] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.293472] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.299712] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.337157] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.343356] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.367395] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.373596] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.387845] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.433990] xen:xen_evtchn: Event-channel device installed [ 1.537232] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.546000] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 113, base_baud = 0) is a S3C6400/10 [ 1.559138] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 114, base_baud = 0) is a S3C6400/10 [ 1.581896] Freeing initrd memory: 11368K [ 1.586363] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 115, base_baud = 0) is a S3C6400/10 [ 1.607160] SuperH (H)SCI(F) driver initialized [ 1.611390] STMicroelectronics ASC driver initialized [ 1.616814] STM32 USART driver initialized [ 1.641369] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.662229] brd: module loaded [ 1.668116] loop: module loaded [ 1.699708] Invalid max_queues (4), will use default max: 2. [ 1.726237] tun: Universal TUN/TAP device driver, 1.6 [ 1.730154] CAN device driver interface [ 1.735255] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.745997] xen_netfront: Initialising Xen virtual ethernet driver [ 1.750922] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.756512] usbcore: registered new interface driver pegasus [ 1.762202] usbcore: registered new interface driver asix [ 1.767698] usbcore: registered new interface driver ax88179_178a [ 1.773837] usbcore: registered new interface driver cdc_ether [ 1.779787] usbcore: registered new interface driver smsc75xx [ 1.785571] usbcore: registered new interface driver smsc95xx [ 1.791409] usbcore: registered new interface driver net1080 [ 1.797132] usbcore: registered new interface driver cdc_subset [ 1.803088] usbcore: registered new interface driver zaurus [ 1.808789] usbcore: registered new interface driver cdc_ncm [ 1.818581] usbcore: registered new interface driver usb-storage [ 1.853400] s5m-rtc s5m-rtc: registered as rtc0 [ 1.862217] s5m-rtc s5m-rtc: setting system clock to 2024-06-26T18:30:43 UTC (1719426643) [ 1.870898] i2c_dev: i2c /dev entries driver [ 1.881411] syscon-poweroff 10040000.system-controller:syscon-poweroff: pm_power_off already claimed for psci_sys_poweroff [ 1.891111] syscon-poweroff: probe of 10040000.system-controller:syscon-poweroff failed with error -16 [ 1.902405] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 1.913377] device-mapper: uevent: version 1.0.3 [ 1.916872] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 1.925794] cpu cpu0: OPP table can't be empty [ 1.930972] failed to register cpuidle driver [ 1.934063] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.942411] sdhci: Secure Digital Host Controller Interface driver [ 1.947440] sdhci: Copyright(c) Pierre Ossman [ 1.955559] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.963365] ledtrig-cpu: registered to indicate activity on CPUs [ 1.969509] usbcore: registered new interface driver usbhid [ 1.973703] usbhid: USB HID core driver [ 1.984722] NET: Registered PF_INET6 protocol family [ 1.989351] Segment Routing with IPv6 [ 1.992083] In-situ OAM (IOAM) with IPv6 [ 1.996094] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.002519] NET: Registered PF_PACKET protocol family [ 2.007208] can: controller area network core [ 2.011620] NET: Registered PF_CAN protocol family [ 2.016477] can: raw protocol [ 2.019476] can: broadcast manager protocol [ 2.023732] can: netlink gateway - max_hops=1 [ 2.028431] Key type dns_resolver registered [ 2.033277] ThumbEE CPU extension supported. [ 2.036879] Registering SWP/SWPB emulation handler [ 2.042143] Loading compiled-in X.509 certificates [ 2.070466] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.076572] clk: Not disabling unused clocks [ 2.083048] Freeing unused kernel image (initmem) memory: 2048K [ 2.089083] Run /init as init process [ 2.091359] with arguments: [ 2.091365] /init [ 2.091371] with environment: [ 2.091376] HOME=/ [ 2.091380] TERM=linux [ 3.105998] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.115823] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.131333] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.141384] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.147019] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.152573] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.162782] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.168391] exynos-ohci 12120000.usb: USB Host Controller [ 3.173872] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.189049] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.194425] Synopsys Designware Multimedia Card Interface Driver [ 3.204418] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.204507] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.227101] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.232498] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.239750] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.246979] hub 1-0:1.0: USB hub found [ 3.247183] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.250822] hub 1-0:1.0: 3 ports detected [ 3.292646] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.299201] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.304284] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.309853] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.319634] mmc_host mmc0: card is polling. [ 3.323778] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.328666] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.330110] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.337218] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.342731] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.351592] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.370445] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.376130] rtc rtc1: invalid alarm value: 1900-01-30T00:00:00 [ 3.383471] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.408993] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.416902] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.420251] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.462382] hub 2-0:1.0: USB hub found [ 3.466818] hub 2-0:1.0: 3 ports detected [ 3.470871] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 3.515935] scsi host0: ahci-dwc [ 3.518103] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 129 [ 3.541231] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 3.553703] mmc1: new high speed SDHC card at address aaaa [ 3.564536] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 3.619771] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.629628] mmc0: new DDR MMC card at address 0001 [ 3.635191] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 3.641771] mmcblk0: p1 p2 p3 p4 [ 3.645855] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 3.653086] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 3.658950] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 3.975623] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 3.982514] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 3.987010] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.008330] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 4.016686] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.022611] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.028037] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.035728] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.036533] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.044007] hub 3-0:1.0: USB hub found [ 4.049627] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.052581] hub 3-0:1.0: 1 port detected [ 4.059222] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.060424] ata1.00: configured for UDMA/133 [ 4.064115] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.071351] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.075090] hub 4-0:1.0: USB hub found [ 4.094777] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.101840] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.107253] hub 4-0:1.0: 1 port detected [ 4.111177] sd 0:0:0:0: [sda] Write Protect is off [ 4.115930] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.117094] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.125282] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.155004] sda: sda1 sda2 < sda5 > [ 4.158089] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.196619] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.284866] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.393562] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.501670] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.609792] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.717901] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.825974] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 4.934067] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.042156] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.150263] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.558990] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 5.666738] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 6.275063] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 11.486469] random: crng init done [ 12.267384] process '/usr/bin/fstype' started with executable stack [ 12.639002] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.961958] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: disabled. [ 14.715070] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.720544] wm8994: probe of 3-001a failed with error -22 [ 15.101630] systemd-udevd[305]: Network interface NamePolicy= disabled on kernel command line, ignoring. [ 16.372380] s5p-secss 10830000.sss: s5p-sss driver registered [ 16.378320] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 16.388312] mc: Linux media interface: v0.10 [ 16.442468] videodev: Linux video capture interface: v2.00 [ 16.571843] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 16.640169] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 16.676998] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.685975] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.693398] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.704968] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 16.710627] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 16.846267] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.907180] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 16.914245] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 16.919144] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.923284] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 16.938367] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 17.026677] usb3503 usb-hub: switched to HUB mode [ 17.029150] blk_print_req_error: 6 callbacks suppressed [ 17.029161] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.030049] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 17.135415] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.147694] systemd-udevd[316]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 17.148461] systemd-udevd[317]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 17.236905] systemd-udevd[317]: Process 'ifupdown-hotplug' failed with exit code 1. [ 17.244401] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.257692] systemd-udevd[316]: Process 'ifupdown-hotplug' failed with exit code 1. [ 17.370342] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.378567] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 17.478466] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.508888] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 17.577834] hub 1-3:1.0: USB hub found [ 17.581190] hub 1-3:1.0: 3 ports detected [ 17.586660] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.696692] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.765169] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.772864] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.781563] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.793188] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 17.801173] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 17.809897] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 17.820649] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.946509] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 18.099257] hub 1-3.2:1.0: USB hub found [ 18.102394] hub 1-3.2:1.0: 4 ports detected [ 18.160652] usbcore: registered new device driver onboard-usb-hub [ 18.230766] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 18.287289] hub 1-3.2:1.0: USB hub found [ 18.290410] hub 1-3.2:1.0: 4 ports detected [ 18.301981] hub 1-3.2:1.0: USB hub found [ 18.304975] hub 1-3.2:1.0: 4 ports detected [ 18.339197] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 18.626499] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 18.779501] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.948273] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 19.450343] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 19.464590] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 19.474380] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 06:24:20:c7:c6:c9 [ 19.516150] systemd-udevd[317]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 19.526018] systemd-udevd[317]: Could not generate persistent MAC address for eth0: No such file or directory [ 19.706357] systemd-udevd[317]: Process 'ifupdown-hotplug' failed with exit code 1. [ 20.121671] EXT4-fs (dm-0): re-mounted. Quota mode: disabled. [ 22.201681] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 22.250385] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: disabled. [ 22.390228] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 23.872947] systemd-udevd[317]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 23.882844] systemd-udevd[317]: Could not generate persistent MAC address for xenbr0: No such file or directory [ 23.883177] xenbr0: port 1(eth0) entered blocking state [ 23.897965] xenbr0: port 1(eth0) entered disabled state [ 23.903362] device eth0 entered promiscuous mode [ 23.914090] systemd-udevd[317]: Process 'ifupdown-hotplug' failed with exit code 1. [ 23.914362] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode