[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod2) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Thu Jun 27 08:36:09 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6084K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000014] Switching to timer-based delay loop, resolution 41ns [ 0.000513] Console: colour dummy device 80x30 [ 0.000531] printk: legacy console [hvc0] enabled [ 0.299007] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309407] CPU: Testing write buffer coherency: ok [ 0.314348] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.323902] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330315] pid_max: default: 32768 minimum: 301 [ 0.335101] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342382] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350813] /cpus/cpu@0 missing clock-frequency property [ 0.355585] /cpus/cpu@1 missing clock-frequency property [ 0.360997] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367698] xen:grant_table: Grant tables using version 1 layout [ 0.372835] Grant table initialized [ 0.376390] xen:events: Using FIFO-based ABI [ 0.380688] Xen: initializing cpu0 [ 0.384212] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392005] rcu: Hierarchical SRCU implementation. [ 0.395605] rcu: Max phase no-delay instances is 1000. [ 0.403823] EFI services will not be available. [ 0.407147] smp: Bringing up secondary CPUs ... [ 0.481396] Xen: initializing cpu1 [ 0.481556] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481581] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500551] smp: Brought up 1 node, 2 CPUs [ 0.504210] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510497] CPU: All CPU(s) started in SVC mode. [ 0.516414] devtmpfs: initialized [ 0.529202] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535766] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545429] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553327] pinctrl core: initialized pinctrl subsystem [ 0.559963] DMI not present or invalid. [ 0.563457] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.570090] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579512] thermal_sys: Registered thermal governor 'step_wise' [ 0.579671] software IO TLB: area num 2. [ 0.588343] software IO TLB: only able to allocate 8 MB [ 0.595417] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600623] No ATAGs? [ 0.602922] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611668] Serial: AMBA PL011 UART driver [ 0.658389] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686889] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.710568] xen:balloon: Initialising balloon driver [ 0.717032] iommu: Default domain type: Translated [ 0.720446] iommu: DMA domain TLB invalidation policy: strict mode [ 0.731823] SCSI subsystem initialized [ 0.734371] libata version 3.00 loaded. [ 0.734606] usbcore: registered new interface driver usbfs [ 0.739803] usbcore: registered new interface driver hub [ 0.745168] usbcore: registered new device driver usb [ 0.751834] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.755422] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.761692] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.766740] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.771674] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.777711] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.783497] pps_core: LinuxPPS API ver. 1 registered [ 0.787880] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.797123] PTP clock support registered [ 0.801330] EDAC MC: Ver: 3.0.0 [ 0.804647] scmi_core: SCMI protocol bus registered [ 0.811284] vgaarb: loaded [ 0.813007] clocksource: Switched to clocksource arch_sys_counter [ 0.826772] NET: Registered PF_INET protocol family [ 0.830411] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.838372] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.846015] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.853819] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.861638] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.868938] TCP: Hash tables configured (established 4096 bind 4096) [ 0.875298] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.881849] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.888999] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.898198] RPC: Registered named UNIX socket transport module. [ 0.902744] RPC: Registered udp transport module. [ 0.907532] RPC: Registered tcp transport module. [ 0.912291] RPC: Registered tcp-with-tls transport module. [ 0.917860] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.924371] PCI: CLS 0 bytes, default 64 [ 0.929820] Initialise system trusted keyrings [ 0.933117] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.939639] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.945518] NFS: Registering the id_resolver key type [ 0.950442] Key type id_resolver registered [ 0.954682] Key type id_legacy registered [ 0.958786] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.965533] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.973313] Trying to unpack rootfs image as initramfs... [ 1.004621] Key type asymmetric registered [ 1.007361] Asymmetric key parser 'x509' registered [ 1.012384] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.019811] io scheduler mq-deadline registered [ 1.024407] io scheduler kyber registered [ 1.028506] io scheduler bfq registered [ 1.162159] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.168433] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.218827] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.225096] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.268373] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.274638] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.314312] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.320515] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.332851] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.364529] xen:xen_evtchn: Event-channel device installed [ 1.459618] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.470733] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.479172] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.488009] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.496889] SuperH (H)SCI(F) driver initialized [ 1.501202] STMicroelectronics ASC driver initialized [ 1.506159] STM32 USART driver initialized [ 1.511660] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.520681] random: crng init done [ 1.528747] brd: module loaded [ 1.534791] loop: module loaded [ 1.552830] Invalid max_queues (4), will use default max: 2. [ 1.560556] Freeing initrd memory: 11856K [ 1.572676] tun: Universal TUN/TAP device driver, 1.6 [ 1.576558] CAN device driver interface [ 1.581664] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.592879] xen_netfront: Initialising Xen virtual ethernet driver [ 1.597754] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.603372] usbcore: registered new interface driver pegasus [ 1.609083] usbcore: registered new interface driver asix [ 1.614557] usbcore: registered new interface driver ax88179_178a [ 1.620710] usbcore: registered new interface driver cdc_ether [ 1.626627] usbcore: registered new interface driver smsc75xx [ 1.632428] usbcore: registered new interface driver smsc95xx [ 1.638260] usbcore: registered new interface driver net1080 [ 1.643983] usbcore: registered new interface driver cdc_subset [ 1.649965] usbcore: registered new interface driver zaurus [ 1.655620] usbcore: registered new interface driver cdc_ncm [ 1.665014] usbcore: registered new interface driver usb-storage [ 1.675566] i2c_dev: i2c /dev entries driver [ 1.694001] device-mapper: uevent: version 1.0.3 [ 1.697419] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.707012] cpu cpu0: OPP table can't be empty [ 1.711749] failed to register cpuidle driver [ 1.715146] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.723483] sdhci: Secure Digital Host Controller Interface driver [ 1.728509] sdhci: Copyright(c) Pierre Ossman [ 1.736547] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.745682] ledtrig-cpu: registered to indicate activity on CPUs [ 1.751116] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.757813] usbcore: registered new interface driver usbhid [ 1.762464] usbhid: USB HID core driver [ 1.773386] NET: Registered PF_INET6 protocol family [ 1.777713] Segment Routing with IPv6 [ 1.780734] In-situ OAM (IOAM) with IPv6 [ 1.784801] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.791168] NET: Registered PF_PACKET protocol family [ 1.795842] can: controller area network core [ 1.800274] NET: Registered PF_CAN protocol family [ 1.805112] can: raw protocol [ 1.808148] can: broadcast manager protocol [ 1.812396] can: netlink gateway - max_hops=1 [ 1.817145] Key type dns_resolver registered [ 1.822221] ThumbEE CPU extension supported. [ 1.825541] Registering SWP/SWPB emulation handler [ 1.840143] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.847434] Loading compiled-in X.509 certificates [ 1.892217] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.895890] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.902383] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.910597] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 1.952160] s5m-rtc s5m-rtc: registered as rtc0 [ 1.961058] s5m-rtc s5m-rtc: setting system clock to 2024-06-27T11:51:19 UTC (1719489079) [ 1.972086] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 1.976778] s3c-i2c 12c90000.i2c: slave address 0x00 [ 1.981063] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 1.988033] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 1.993825] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.000032] clk: Not disabling unused clocks [ 2.003556] PM: genpd: Disabling unused power domains [ 2.012087] Freeing unused kernel image (initmem) memory: 2048K [ 2.018365] Run /init as init process [ 2.020649] with arguments: [ 2.020656] /init [ 2.020662] with environment: [ 2.020667] HOME=/ [ 2.020673] TERM=linux [ 3.279475] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.371568] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.378686] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.406289] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.509116] Synopsys Designware Multimedia Card Interface Driver [ 3.524072] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.530279] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.537765] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.550865] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.569976] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.593852] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.602943] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.608689] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.617585] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.624407] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.651433] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.656533] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.662054] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 125,32 bit host data width,128 deep fifo [ 3.672361] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.678104] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.678155] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.683614] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.748975] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.759810] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.766308] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.771928] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.777558] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.790012] scsi host0: ahci-dwc [ 3.803955] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 127 lpm-pol 0 [ 3.804216] mmc_host mmc0: card is polling. [ 3.817599] exynos-ehci 12110000.usb: irq 129, io mem 0x12110000 [ 3.843625] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.850705] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.863971] hub 1-0:1.0: USB hub found [ 3.872986] hub 1-0:1.0: 3 ports detected [ 3.885077] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.890702] exynos-ohci 12120000.usb: USB Host Controller [ 3.896211] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.906258] exynos-ohci 12120000.usb: irq 129, io mem 0x12120000 [ 3.987606] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.989184] hub 2-0:1.0: USB hub found [ 4.001065] hub 2-0:1.0: 3 ports detected [ 4.004722] mmc0: new DDR MMC card at address 0001 [ 4.007868] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.021548] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.026226] mmc1: new high speed SDHC card at address aaaa [ 4.042093] mmcblk0: p1 p2 p3 p4 [ 4.042545] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.050428] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.056358] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.062184] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.323104] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.329029] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.334734] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.342537] ata1.00: configured for UDMA/133 [ 4.345997] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.355687] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.361808] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.367881] sd 0:0:0:0: [sda] Write Protect is off [ 4.371985] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.372139] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.381329] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.413109] sda: sda1 sda2 < sda5 > [ 4.416134] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.455376] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.473522] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.483799] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.577115] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.589058] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.593962] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.599266] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.607019] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.618592] hub 3-0:1.0: USB hub found [ 4.621054] hub 3-0:1.0: 1 port detected [ 4.626870] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.634544] hub 4-0:1.0: USB hub found [ 4.637498] hub 4-0:1.0: 1 port detected [ 9.018268] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 9.183565] EXT4-fs (dm-0): mounted filesystem 1f7a8c75-313e-41c0-b21c-1ce3a2e6f2d3 ro with ordered data mode. Quota mode: disabled. [ 13.101051] usb3503 usb-hub: switched to HUB mode [ 13.104472] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 13.178010] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 13.259758] mc: Linux media interface: v0.10 [ 13.263271] s5p-secss 10830000.sss: s5p-sss driver registered [ 13.441962] videodev: Linux video capture interface: v2.00 [ 13.613108] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 13.805706] exynos-gsc 13e00000.gsc: Adding to iommu group 0 [ 13.811436] exynos-gsc 13e10000.gsc: Adding to iommu group 1 [ 13.816862] exynos-gsc 13e20000.gsc: Adding to iommu group 2 [ 13.822533] exynos-gsc 13e30000.gsc: Adding to iommu group 3 [ 13.833251] s5p-mfc 11000000.codec: Adding to iommu group 4 [ 13.842876] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 13.874532] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 13.883095] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 13.891035] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 13.901964] hub 1-3:1.0: USB hub found [ 13.906663] hub 1-3:1.0: 3 ports detected [ 13.909710] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 13.926470] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 13.985792] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 14.047779] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.052911] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 14.314076] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 14.580940] hub 1-3.2:1.0: USB hub found [ 14.583981] hub 1-3.2:1.0: 4 ports detected [ 14.634957] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.642659] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.651412] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.666949] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.674667] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.683357] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.730276] usbcore: registered new device driver onboard-usb-dev [ 14.865913] hub 1-3.2:1.0: USB hub found [ 14.868828] hub 1-3.2:1.0: 4 ports detected [ 14.880972] hub 1-3.2:1.0: USB hub found [ 14.883996] hub 1-3.2:1.0: 4 ports detected [ 15.093642] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 15.246983] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 15.644100] EXT4-fs (dm-0): re-mounted 1f7a8c75-313e-41c0-b21c-1ce3a2e6f2d3 r/w. Quota mode: disabled. [ 16.004955] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 16.019831] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 16.029855] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 3a:9f:af:f4:1a:be [ 17.764911] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.805806] EXT4-fs (sda1): mounted filesystem 1d3ecd1d-4258-43d5-8084-59bf8a6d00c1 r/w with ordered data mode. Quota mode: disabled. [ 17.902096] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 19.733532] xenbr0: port 1(eth0) entered blocking state [ 19.737392] xenbr0: port 1(eth0) entered disabled state [ 19.742704] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 19.748587] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 19.759350] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 21.940313] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 21.946388] xenbr0: port 1(eth0) entered blocking state [ 21.951555] xenbr0: port 1(eth0) entered forwarding state