[ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Thu Jun 27 22:42:25 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/godello1--vg-root ro console=hvc0 [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009efff] usable [ 0.000000] Xen: [mem 0x000000000009f000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020060fff] usable [ 0.000000] Xen: [mem 0x000000009573f000-0x0000000095bbefff] reserved [ 0.000000] Xen: [mem 0x0000000095bbf000-0x0000000095fbefff] ACPI NVS [ 0.000000] Xen: [mem 0x0000000095fbf000-0x0000000095ffefff] ACPI data [ 0.000000] Xen: [mem 0x0000000096000000-0x000000009fffffff] reserved [ 0.000000] Xen: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved [ 0.000000] Xen: [mem 0x00000000feb00000-0x00000000feb03fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fed10000-0x00000000fed19fff] reserved [ 0.000000] Xen: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] Xen: [mem 0x00000000fed90000-0x00000000fed90fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: Dell Inc. PowerEdge R220/081N4V, BIOS 1.1.4 05/06/2014 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000022] Xen PV: Detected 4 vCPUS [ 0.000487] tsc: Detected 3092.838 MHz processor [ 0.000809] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000813] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000820] last_pfn = 0x20061 max_arch_pfn = 0x400000000 [ 0.000824] MTRR map: 4 entries (0 fixed + 4 variable; max 20), built from 10 variable MTRRs [ 0.000826] MTRRs set to read-only [ 0.000830] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.000882] Kernel/User page tables isolation: disabled on XEN PV. [ 0.020160] RAMDISK: [mem 0x04000000-0x053a4fff] [ 0.020176] ACPI: Early table checksum verification disabled [ 0.021823] ACPI: RSDP 0x00000000000FE020 000024 (v02 DELL ) [ 0.021838] ACPI: XSDT 0x0000000095FCF188 0000E4 (v01 DELL PE_SC3 00000001 01000013) [ 0.021903] ACPI: FACP 0x0000000095FF7000 00010C (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.021985] ACPI: DSDT 0x0000000095FDF000 012335 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.022000] ACPI: FACS 0x0000000095FBD000 000040 [ 0.022016] ACPI: UEFI 0x0000000095FFD000 000236 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022030] ACPI: UEFI 0x0000000095FFC000 000042 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.022045] ACPI: ASF! 0x0000000095FFB000 0000A5 (v32 DELL PE_SC3 00000001 DELL 00040000) [ 0.022059] ACPI: ASPT 0x0000000095FFA000 000034 (v07 DELL PE_SC3 00000001 DELL 00040000) [ 0.022073] ACPI: BOOT 0x0000000095FF9000 000028 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022087] ACPI: DBGP 0x0000000095FF8000 000034 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022101] ACPI: HPET 0x0000000095FF6000 000038 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022115] ACPI: APIC 0x0000000095FF5000 000092 (v03 DELL PE_SC3 00000001 DELL 00040000) [ 0.022128] ACPI: MCFG 0x0000000095FF4000 00003C (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022142] ACPI: SLIC 0x0000000095FF3000 000176 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022156] ACPI: SSDT 0x0000000095FDC000 002028 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.022170] ACPI: SPMI 0x0000000095FDA000 000040 (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.022185] ACPI: SSDT 0x0000000095FD9000 000533 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022199] ACPI: SSDT 0x0000000095FD8000 000ACE (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022213] ACPI: SSDT 0x0000000095FD4000 003492 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022226] ACPI: SPCR 0x0000000095FF2000 000050 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022240] ACPI: RMAD 0x0000000095FD3000 000080 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022253] ACPI: SSDT 0x0000000095FD2000 000514 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.022266] ACPI: FPDT 0x0000000095FD1000 000044 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022280] ACPI: HEST 0x0000000095FD0000 0000A8 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022295] ACPI: ERST 0x0000000095FCE000 000230 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022308] ACPI: BERT 0x0000000095FCD000 000030 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022321] ACPI: EINJ 0x0000000095FCC000 000150 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022328] ACPI: Reserving FACP table memory at [mem 0x95ff7000-0x95ff710b] [ 0.022329] ACPI: Reserving DSDT table memory at [mem 0x95fdf000-0x95ff1334] [ 0.022330] ACPI: Reserving FACS table memory at [mem 0x95fbd000-0x95fbd03f] [ 0.022331] ACPI: Reserving UEFI table memory at [mem 0x95ffd000-0x95ffd235] [ 0.022332] ACPI: Reserving UEFI table memory at [mem 0x95ffc000-0x95ffc041] [ 0.022333] ACPI: Reserving ASF! table memory at [mem 0x95ffb000-0x95ffb0a4] [ 0.022333] ACPI: Reserving ASPT table memory at [mem 0x95ffa000-0x95ffa033] [ 0.022334] ACPI: Reserving BOOT table memory at [mem 0x95ff9000-0x95ff9027] [ 0.022335] ACPI: Reserving DBGP table memory at [mem 0x95ff8000-0x95ff8033] [ 0.022335] ACPI: Reserving HPET table memory at [mem 0x95ff6000-0x95ff6037] [ 0.022336] ACPI: Reserving APIC table memory at [mem 0x95ff5000-0x95ff5091] [ 0.022337] ACPI: Reserving MCFG table memory at [mem 0x95ff4000-0x95ff403b] [ 0.022337] ACPI: Reserving SLIC table memory at [mem 0x95ff3000-0x95ff3175] [ 0.022338] ACPI: Reserving SSDT table memory at [mem 0x95fdc000-0x95fde027] [ 0.022339] ACPI: Reserving SPMI table memory at [mem 0x95fda000-0x95fda03f] [ 0.022340] ACPI: Reserving SSDT table memory at [mem 0x95fd9000-0x95fd9532] [ 0.022341] ACPI: Reserving SSDT table memory at [mem 0x95fd8000-0x95fd8acd] [ 0.022342] ACPI: Reserving SSDT table memory at [mem 0x95fd4000-0x95fd7491] [ 0.022343] ACPI: Reserving SPCR table memory at [mem 0x95ff2000-0x95ff204f] [ 0.022343] ACPI: Reserving RMAD table memory at [mem 0x95fd3000-0x95fd307f] [ 0.022344] ACPI: Reserving SSDT table memory at [mem 0x95fd2000-0x95fd2513] [ 0.022345] ACPI: Reserving FPDT table memory at [mem 0x95fd1000-0x95fd1043] [ 0.022346] ACPI: Reserving HEST table memory at [mem 0x95fd0000-0x95fd00a7] [ 0.022347] ACPI: Reserving ERST table memory at [mem 0x95fce000-0x95fce22f] [ 0.022348] ACPI: Reserving BERT table memory at [mem 0x95fcd000-0x95fcd02f] [ 0.022349] ACPI: Reserving EINJ table memory at [mem 0x95fcc000-0x95fcc14f] [ 0.022481] APIC: Switched APIC routing to: Xen PV [ 0.025565] Zone ranges: [ 0.025567] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.025569] DMA32 [mem 0x0000000001000000-0x0000000020060fff] [ 0.025571] Normal empty [ 0.025572] Movable zone start for each node [ 0.025573] Early memory node ranges [ 0.025573] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.025576] node 0: [mem 0x0000000000100000-0x0000000020060fff] [ 0.025577] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020060fff] [ 0.025587] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.025667] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.029062] On node 0, zone DMA32: 32671 pages in unavailable ranges [ 0.029067] p2m virtual area at (____ptrval____), size is 40000000 [ 0.121550] Remapped 97 page(s) [ 0.122088] ACPI: PM-Timer IO Port: 0x1808 [ 0.122163] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.122196] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.122213] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.122217] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.122243] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.122249] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.122259] ACPI: SPCR: SPCR table version 1 [ 0.122262] ACPI: SPCR: console: uart,io,0x3f8,115200 [ 0.122266] CPU topo: 8 possible CPUs exceed the limit of 4 [ 0.122275] CPU topo: Max. logical packages: 1 [ 0.122276] CPU topo: Max. logical dies: 1 [ 0.122276] CPU topo: Max. dies per package: 1 [ 0.122283] CPU topo: Max. threads per core: 1 [ 0.122284] CPU topo: Num. cores per package: 4 [ 0.122285] CPU topo: Num. threads per package: 4 [ 0.122285] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.122302] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.122305] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] [ 0.122307] [mem 0x20061000-0x9573efff] available for PCI devices [ 0.122312] Booting kernel on Xen [ 0.122313] Xen version: 4.19-unstable (preserve-AD) [ 0.122317] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.128324] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.129255] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.129262] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.129266] pcpu-alloc: [0] 0 1 2 3 [ 0.129337] xen: PV spinlocks enabled [ 0.129344] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.129348] Kernel command line: placeholder root=/dev/mapper/godello1--vg-root ro console=hvc0 [ 0.129424] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.129448] random: crng init done [ 0.129607] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.129690] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.130279] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.130285] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.130289] software IO TLB: area num 4. [ 0.216662] Memory: 386520K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137512K reserved, 0K cma-reserved) [ 0.216794] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.219249] Dynamic Preempt: voluntary [ 0.219380] rcu: Preemptible hierarchical RCU implementation. [ 0.219381] rcu: RCU event tracing is enabled. [ 0.219382] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.219384] Trampoline variant of Tasks RCU enabled. [ 0.219385] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.219386] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.219405] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.227937] NR_IRQS: 4352, nr_irqs: 456, preallocated irqs: 16 [ 0.228085] xen:events: Using FIFO-based ABI [ 0.228113] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.228120] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.228125] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.228131] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.228137] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.228146] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.228152] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.228157] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.228162] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.228168] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.228173] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.228179] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.228185] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.228190] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.228196] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.228207] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.237352] Console: colour VGA+ 80x25 [ 0.237357] printk: legacy console [tty0] enabled [ 0.258052] printk: legacy console [hvc0] enabled [ 0.259179] ACPI: Core revision 20240322 [ 0.279494] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.279701] Xen: using vcpuop timer interface [ 0.279713] installing Xen timer for CPU 0 [ 0.279911] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2c94d9afcf4, max_idle_ns: 440795231738 ns [ 0.280099] Calibrating delay loop (skipped), value calculated using timer frequency.. 6185.67 BogoMIPS (lpj=3092838) [ 0.280435] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024 [ 0.280580] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4 [ 0.281118] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.281296] Spectre V2 : Mitigation: Retpolines [ 0.281442] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.281618] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.281758] Spectre V2 : Enabling Restricted Speculation for firmware calls [ 0.281905] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.282080] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.282103] MDS: Mitigation: Clear CPU buffers [ 0.282240] MMIO Stale Data: Unknown: No mitigations [ 0.282380] SRBDS: Unknown: Dependent on hypervisor status [ 0.282557] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.282731] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.282879] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.283024] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.283099] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.305992] Freeing SMP alternatives memory: 40K [ 0.306103] pid_max: default: 32768 minimum: 301 [ 0.306273] LSM: initializing lsm=capability,selinux [ 0.306416] SELinux: Initializing. [ 0.306589] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.306767] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.308207] cpu 0 spinlock event irq 25 [ 0.308352] VPMU disabled by hypervisor. [ 0.308889] Performance Events: unsupported p6 CPU model 60 no PMU driver, software events only. [ 0.309065] signal: max sigframe size: 1776 [ 0.309159] rcu: Hierarchical SRCU implementation. [ 0.309301] rcu: Max phase no-delay instances is 400. [ 0.309859] smp: Bringing up secondary CPUs ... [ 0.310199] installing Xen timer for CPU 1 [ 0.310646] installing Xen timer for CPU 2 [ 0.311012] installing Xen timer for CPU 3 [ 0.052886] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0002 [ 0.311183] cpu 1 spinlock event irq 45 [ 0.052886] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0004 [ 0.311461] cpu 2 spinlock event irq 46 [ 0.052886] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0006 [ 0.312141] cpu 3 spinlock event irq 47 [ 0.312456] smp: Brought up 1 node, 4 CPUs [ 0.313304] devtmpfs: initialized [ 0.313304] x86/mm: Memory block size: 128MB [ 0.313717] ACPI: PM: Registering ACPI NVS region [mem 0x95bbf000-0x95fbefff] (4194304 bytes) [ 0.314195] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.314380] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.314648] PM: RTC time: 23:56:14, date: 2024-06-27 [ 0.314897] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.315072] xen:grant_table: Grant tables using version 1 layout [ 0.315132] Grant table initialized [ 0.315391] audit: initializing netlink subsys (disabled) [ 0.315583] audit: type=2000 audit(1719532575.459:1): state=initialized audit_enabled=0 res=1 [ 0.315583] thermal_sys: Registered thermal governor 'step_wise' [ 0.315583] thermal_sys: Registered thermal governor 'user_space' [ 0.316104] Simple Boot Flag at 0x44 set to 0x1 [ 0.316409] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.316724] PCI: ECAM [mem 0xf0000000-0xf7ffffff] (base 0xf0000000) for domain 0000 [bus 00-7f] [ 0.316907] PCI: ECAM [mem 0xf0000000-0xf7ffffff] reserved as E820 entry [ 0.363320] PCI: Using configuration type 1 for base access [ 0.363533] PCI: Dell System detected, enabling pci=bfsort. [ 0.363797] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.364148] ACPI: Added _OSI(Module Device) [ 0.364274] ACPI: Added _OSI(Processor Device) [ 0.364436] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.364573] ACPI: Added _OSI(Processor Aggregator Device) [ 0.375259] ACPI: 6 ACPI AML tables successfully acquired and loaded [ 0.376041] xen: registering gsi 9 triggering 0 polarity 0 [ 0.376518] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.378170] ACPI: Dynamic OEM Table Load: [ 0.378315] ACPI: SSDT 0xFFFF88800399E000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120816) [ 0.379196] ACPI: Dynamic OEM Table Load: [ 0.379341] ACPI: SSDT 0xFFFF888003ADC800 0005AA (v01 PmRef ApIst 00003000 INTL 20120816) [ 0.380148] ACPI: Dynamic OEM Table Load: [ 0.380291] ACPI: SSDT 0xFFFF888003981200 000119 (v01 PmRef ApCst 00003000 INTL 20120816) [ 0.381358] ACPI: _OSC evaluated successfully for all CPUs [ 0.381655] ACPI: Interpreter enabled [ 0.381810] ACPI: PM: (supports S0 S4 S5) [ 0.381945] ACPI: Using IOAPIC for interrupt routing [ 0.382110] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.382289] PCI: Using E820 reservations for host bridge windows [ 0.382680] ACPI: Enabled 11 GPEs in block 00 to 3F [ 0.390558] acpi ABCD0000:00: ACPI dock station (docks/bays count: 1) [ 0.398625] ACPI: \_TZ_.FN00: New power resource [ 0.398808] ACPI: \_TZ_.FN01: New power resource [ 0.398984] ACPI: \_TZ_.FN02: New power resource [ 0.399138] ACPI: \_TZ_.FN03: New power resource [ 0.399314] ACPI: \_TZ_.FN04: New power resource [ 0.400166] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e]) [ 0.400314] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.401334] acpi PNP0A08:00: _OSC: OS now controls [PME PCIeCapability LTR] [ 0.401483] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration [ 0.402132] PCI host bridge to bus 0000:00 [ 0.402271] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.402418] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.402567] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.402741] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xfeafffff window] [ 0.402914] pci_bus 0000:00: root bus resource [bus 00-7e] [ 0.403087] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000 conventional PCI endpoint [ 0.403679] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330 conventional PCI endpoint [ 0.403926] pci 0000:00:14.0: BAR 0 [mem 0xa2b00000-0xa2b0ffff 64bit] [ 0.404346] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 0.404713] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320 conventional PCI endpoint [ 0.404946] pci 0000:00:1a.0: BAR 0 [mem 0xa2b12000-0xa2b123ff] [ 0.405402] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 0.405736] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400 PCIe Root Port [ 0.406027] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.406159] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.406560] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.406776] pci 0000:00:1c.0: Enabling MPC IRBNCE [ 0.406919] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled [ 0.407397] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400 PCIe Root Port [ 0.407694] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.407857] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.408033] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.408331] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.408545] pci 0000:00:1c.2: Enabling MPC IRBNCE [ 0.408688] pci 0000:00:1c.2: Intel PCH root port ACS workaround enabled [ 0.409200] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320 conventional PCI endpoint [ 0.409434] pci 0000:00:1d.0: BAR 0 [mem 0xa2b11000-0xa2b113ff] [ 0.409895] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 0.410231] pci 0000:00:1f.0: [8086:8c52] type 00 class 0x060100 conventional PCI endpoint [ 0.410922] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601 conventional PCI endpoint [ 0.411162] pci 0000:00:1f.2: BAR 0 [io 0x3048-0x304f] [ 0.411334] pci 0000:00:1f.2: BAR 1 [io 0x3054-0x3057] [ 0.411504] pci 0000:00:1f.2: BAR 2 [io 0x3040-0x3047] [ 0.411676] pci 0000:00:1f.2: BAR 3 [io 0x3050-0x3053] [ 0.411842] pci 0000:00:1f.2: BAR 4 [io 0x3020-0x303f] [ 0.412012] pci 0000:00:1f.2: BAR 5 [mem 0xa2b10000-0xa2b107ff] [ 0.412283] pci 0000:00:1f.2: PME# supported from D3hot [ 0.412585] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500 conventional PCI endpoint [ 0.412834] pci 0000:00:1f.3: BAR 0 [mem 0xa2b13000-0xa2b130ff 64bit] [ 0.413068] pci 0000:00:1f.3: BAR 4 [io 0x3000-0x301f] [ 0.413555] pci 0000:01:00.0: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.413883] pci 0000:01:00.0: BAR 0 [mem 0xa2a30000-0xa2a3ffff 64bit pref] [ 0.414200] pci 0000:01:00.0: BAR 2 [mem 0xa2a40000-0xa2a4ffff 64bit pref] [ 0.414464] pci 0000:01:00.0: BAR 4 [mem 0xa2a50000-0xa2a5ffff 64bit pref] [ 0.414702] pci 0000:01:00.0: ROM [mem 0x00000000-0x0003ffff pref] [ 0.415274] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.416057] pci 0000:01:00.1: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.416251] pci 0000:01:00.1: BAR 0 [mem 0xa2a00000-0xa2a0ffff 64bit pref] [ 0.416522] pci 0000:01:00.1: BAR 2 [mem 0xa2a10000-0xa2a1ffff 64bit pref] [ 0.416786] pci 0000:01:00.1: BAR 4 [mem 0xa2a20000-0xa2a2ffff 64bit pref] [ 0.417016] pci 0000:01:00.1: ROM [mem 0x00000000-0x0003ffff pref] [ 0.417533] pci 0000:01:00.1: PME# supported from D0 D3hot D3cold [ 0.418358] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.419712] pci 0000:02:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Upstream Port [ 0.421015] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.421337] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.421804] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.423738] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.425315] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.426828] pci 0000:03:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.428203] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.428601] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.429099] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.431214] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold [ 0.433138] pci 0000:03:01.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.434535] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.434924] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.437615] pci 0000:03:01.0: PME# supported from D0 D3hot D3cold [ 0.441435] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.443251] pci 0000:04:00.0: [1912:0012] type 01 class 0x060400 PCIe to PCI/PCI-X bridge [ 0.444655] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.445046] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.445459] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.448946] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.450533] pci_bus 0000:05: extended config space not accessible [ 0.450933] pci 0000:05:00.0: [102b:0534] type 00 class 0x030000 conventional PCI endpoint [ 0.451591] pci 0000:05:00.0: BAR 0 [mem 0xa1000000-0xa1ffffff pref] [ 0.451999] pci 0000:05:00.0: BAR 1 [mem 0xa2800000-0xa2803fff] [ 0.452367] pci 0000:05:00.0: BAR 2 [mem 0xa2000000-0xa27fffff] [ 0.453853] pci 0000:05:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.457431] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.459685] pci 0000:06:00.0: [1912:0011] type 00 class 0x050000 conventional PCI endpoint [ 0.460324] pci 0000:06:00.0: BAR 0 [mem 0xa2901000-0xa2901fff] [ 0.460730] pci 0000:06:00.0: BAR 1 [mem 0xa2900000-0xa290007f] [ 0.463177] pci 0000:06:00.0: PME# supported from D3hot [ 0.464293] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.466094] pci_bus 0000:00: on NUMA node 0 [ 0.466311] xen: registering gsi 13 triggering 1 polarity 0 [ 0.467319] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.467531] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.467741] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.467961] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.468173] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.468317] ACPI: PCI: Interrupt link LNKE disabled [ 0.468520] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.468663] ACPI: PCI: Interrupt link LNKF disabled [ 0.468868] ACPI: PCI: Interrupt link LNKG configured for IRQ 0 [ 0.469010] ACPI: PCI: Interrupt link LNKG disabled [ 0.469169] ACPI: PCI: Interrupt link LNKH configured for IRQ 11 [ 0.469830] xen:balloon: Initialising balloon driver [ 0.470108] iommu: Default domain type: Translated [ 0.470250] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.470442] SCSI subsystem initialized [ 0.470592] libata version 3.00 loaded. [ 0.470592] ACPI: bus type USB registered [ 0.470592] usbcore: registered new interface driver usbfs [ 0.470592] usbcore: registered new interface driver hub [ 0.471105] usbcore: registered new device driver usb [ 0.471258] pps_core: LinuxPPS API ver. 1 registered [ 0.471392] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.471573] PTP clock support registered [ 0.471725] Advanced Linux Sound Architecture Driver Initialized. [ 0.472173] NetLabel: Initializing [ 0.472308] NetLabel: domain hash size = 128 [ 0.472447] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.472602] NetLabel: unlabeled traffic allowed by default [ 0.472761] PCI: Using ACPI for IRQ routing [ 0.489084] PCI: pci_cache_line_size set to 64 bytes [ 0.489723] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] [ 0.489725] e820: reserve RAM buffer [mem 0x20061000-0x23ffffff] [ 0.489745] pci 0000:05:00.0: vgaarb: setting as boot VGA device [ 0.489745] pci 0000:05:00.0: vgaarb: bridge control possible [ 0.489745] pci 0000:05:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.490100] vgaarb: loaded [ 0.490315] clocksource: Switched to clocksource tsc-early [ 0.490511] VFS: Disk quotas dquot_6.6.0 [ 0.490652] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.490819] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.490999] pnp: PnP ACPI init [ 0.491042] system 00:00: [io 0x0680-0x069f] has been reserved [ 0.491188] system 00:00: [io 0xffff] has been reserved [ 0.491328] system 00:00: [io 0xffff] has been reserved [ 0.491468] system 00:00: [io 0xffff] has been reserved [ 0.491611] system 00:00: [io 0x1800-0x18fe] has been reserved [ 0.491765] system 00:00: [io 0x164e-0x164f] has been reserved [ 0.491924] system 00:01: [io 0x0800-0x087f] has been reserved [ 0.492122] xen: registering gsi 8 triggering 1 polarity 0 [ 0.492176] system 00:03: [io 0x1854-0x1857] has been reserved [ 0.492605] xen: registering gsi 3 triggering 1 polarity 0 [ 0.492865] xen: registering gsi 4 triggering 1 polarity 0 [ 0.492868] Already setup the GSI :4 [ 0.493184] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.493328] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved [ 0.493473] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.493619] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.493759] system 00:06: [mem 0xf0000000-0xf7ffffff] has been reserved [ 0.493905] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved [ 0.494051] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved [ 0.494199] system 00:06: [mem 0xff000000-0xffffffff] could not be reserved [ 0.494345] system 00:06: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.494491] system 00:06: [mem 0xa0000000-0xa0000fff] has been reserved [ 0.494631] system 00:06: [mem 0xa0020000-0xa002ffff] has been reserved [ 0.495635] pnp: PnP ACPI: found 7 devices [ 0.517341] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.517506] NET: Registered PF_INET protocol family [ 0.517670] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.517995] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.518188] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.518376] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.518570] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.518764] TCP: Hash tables configured (established 4096 bind 4096) [ 0.518922] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.519068] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.519242] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.519555] RPC: Registered named UNIX socket transport module. [ 0.519696] RPC: Registered udp transport module. [ 0.519834] RPC: Registered tcp transport module. [ 0.519973] RPC: Registered tcp-with-tls transport module. [ 0.520121] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.520573] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff]: assigned [ 0.520750] pci 0000:01:00.0: ROM [mem 0xa0100000-0xa013ffff pref]: assigned [ 0.520897] pci 0000:01:00.1: ROM [mem 0xa0140000-0xa017ffff pref]: assigned [ 0.521044] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.521215] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff] [ 0.521409] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.521601] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.521883] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.522128] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.522502] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.522784] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.523024] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.523403] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.523685] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.524182] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.524474] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.524705] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.525133] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.525287] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.525441] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.525632] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.525782] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.525926] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.526071] pci_bus 0000:00: resource 7 [mem 0xa0000000-0xfeafffff window] [ 0.526224] pci_bus 0000:01: resource 1 [mem 0xa0100000-0xa01fffff] [ 0.526369] pci_bus 0000:01: resource 2 [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.526536] pci_bus 0000:02: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.526674] pci_bus 0000:02: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.526846] pci_bus 0000:03: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.526991] pci_bus 0000:03: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.527165] pci_bus 0000:04: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.527313] pci_bus 0000:04: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.527491] pci_bus 0000:05: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.527633] pci_bus 0000:05: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.527807] pci_bus 0000:06: resource 1 [mem 0xa2900000-0xa29fffff] [ 0.528077] xen: registering gsi 16 triggering 0 polarity 1 [ 0.528108] xen: --> pirq=16 -> irq=16 (gsi=16) [ 0.529539] xen: registering gsi 16 triggering 0 polarity 1 [ 0.529543] Already setup the GSI :16 [ 0.541226] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x7c0 took 11455 usecs [ 0.541478] xen: registering gsi 23 triggering 0 polarity 1 [ 0.541499] xen: --> pirq=23 -> irq=23 (gsi=23) [ 0.553220] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x7c0 took 11514 usecs [ 0.553706] PCI: CLS 64 bytes, default 64 [ 0.553876] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.553926] Unpacking initramfs... [ 0.554022] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 0.556412] kvm_intel: VMX not supported by CPU 0 [ 0.556561] kvm_amd: CPU 0 isn't AMD or Hygon [ 0.556703] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c94d9afcf4, max_idle_ns: 440795231738 ns [ 0.557475] clocksource: Switched to clocksource tsc [ 0.560949] Initialise system trusted keyrings [ 0.561164] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 0.561434] NFS: Registering the id_resolver key type [ 0.561581] Key type id_resolver registered [ 0.561713] Key type id_legacy registered [ 0.561890] 9p: Installing v9fs 9p2000 file system support [ 0.574159] Key type asymmetric registered [ 0.574316] Asymmetric key parser 'x509' registered [ 0.574474] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.574656] io scheduler mq-deadline registered [ 0.574796] io scheduler kyber registered [ 0.575367] xen: registering gsi 16 triggering 0 polarity 1 [ 0.575374] Already setup the GSI :16 [ 0.575733] pcieport 0000:00:1c.0: PME: Signaling with IRQ 50 [ 0.576121] xen: registering gsi 18 triggering 0 polarity 1 [ 0.576137] xen: --> pirq=18 -> irq=18 (gsi=18) [ 0.576310] pcieport 0000:00:1c.2: PME: Signaling with IRQ 51 [ 0.580692] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.580936] ACPI: button: Power Button [PWRF] [ 0.581447] Monitor-Mwait will be used to enter C-1 state [ 0.581457] Monitor-Mwait will be used to enter C-2 state [ 0.581461] ACPI: \_PR_.CPU0: Found 2 idle states [ 0.581791] ACPI: \_PR_.CPU1: Found 2 idle states [ 0.582145] ACPI: \_PR_.CPU2: Found 2 idle states [ 0.582469] ACPI: \_PR_.CPU3: Found 2 idle states [ 0.583079] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.583227] ACPI: thermal: Thermal Zone [TZ00] (28 C) [ 0.583591] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.583742] ACPI: thermal: Thermal Zone [TZ01] (30 C) [ 0.584195] xen:xen_evtchn: Event-channel device installed [ 0.584424] xen_pciback: backend is vpci [ 0.585003] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.585281] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 0.586004] hpet_acpi_add: no address or irqs in _CRS [ 0.586202] Non-volatile memory driver v1.3 [ 0.587532] loop: module loaded [ 0.591252] ahci 0000:00:1f.2: version 3.0 [ 0.591341] xen: registering gsi 19 triggering 0 polarity 1 [ 0.591365] xen: --> pirq=19 -> irq=19 (gsi=19) [ 0.591535] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled [ 0.591713] ahci 0000:00:1f.2: AHCI vers 0001.0300, 32 command slots, 6 Gbps, SATA mode [ 0.591902] ahci 0000:00:1f.2: 3/6 ports implemented (port mask 0x31) [ 0.592049] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst [ 0.598397] scsi host0: ahci [ 0.598739] scsi host1: ahci [ 0.599043] scsi host2: ahci [ 0.599310] scsi host3: ahci [ 0.599577] scsi host4: ahci [ 0.599851] scsi host5: ahci [ 0.600028] ata1: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10100 irq 53 lpm-pol 0 [ 0.600204] ata2: DUMMY [ 0.600333] ata3: DUMMY [ 0.600464] ata4: DUMMY [ 0.600595] ata5: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10300 irq 53 lpm-pol 0 [ 0.600777] ata6: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10380 irq 53 lpm-pol 0 [ 0.601161] tun: Universal TUN/TAP device driver, 1.6 [ 0.601544] xen: registering gsi 16 triggering 0 polarity 1 [ 0.601550] Already setup the GSI :16 [ 0.635233] Freeing initrd memory: 20116K [ 0.635633] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:88 [ 0.635825] tg3 0000:01:00.0 eth0: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.636018] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.636193] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.636753] xen: registering gsi 17 triggering 0 polarity 1 [ 0.636777] xen: --> pirq=17 -> irq=17 (gsi=17) [ 0.684240] tg3 0000:01:00.1 eth1: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:8a [ 0.684429] tg3 0000:01:00.1 eth1: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.684611] tg3 0000:01:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.684785] tg3 0000:01:00.1 eth1: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.685243] e100: Intel(R) PRO/100 Network Driver [ 0.685384] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.685536] sky2: driver version 1.30 [ 0.685693] xen_netfront: Initialising Xen virtual ethernet driver [ 0.686121] xen: registering gsi 16 triggering 0 polarity 1 [ 0.686128] Already setup the GSI :16 [ 0.686131] xen: registering gsi 16 triggering 0 polarity 1 [ 0.686136] Already setup the GSI :16 [ 0.686191] xen: registering gsi 23 triggering 0 polarity 1 [ 0.686196] Already setup the GSI :23 [ 0.686256] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 0.686350] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.686885] ehci-pci 0000:00:1d.0: debug port 2 [ 0.691034] ehci-pci 0000:00:1d.0: irq 23, io mem 0xa2b11000 [ 0.697960] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 0.698213] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.698396] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.698572] usb usb1: Product: EHCI Host Controller [ 0.698711] usb usb1: Manufacturer: Linux 6.10.0-rc5+ ehci_hcd [ 0.698859] usb usb1: SerialNumber: 0000:00:1d.0 [ 0.699189] hub 1-0:1.0: USB hub found [ 0.699342] hub 1-0:1.0: 2 ports detected [ 0.699665] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 0.699891] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 2 [ 0.700110] ehci-pci 0000:00:1a.0: debug port 2 [ 0.704293] ehci-pci 0000:00:1a.0: irq 16, io mem 0xa2b12000 [ 0.710949] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 0.711161] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.711375] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.711549] usb usb2: Product: EHCI Host Controller [ 0.711689] usb usb2: Manufacturer: Linux 6.10.0-rc5+ ehci_hcd [ 0.711832] usb usb2: SerialNumber: 0000:00:1a.0 [ 0.712121] hub 2-0:1.0: USB hub found [ 0.712268] hub 2-0:1.0: 2 ports detected [ 0.712585] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.712819] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 0.714088] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810 [ 0.714521] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.714726] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 0.714912] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [ 0.715281] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.715464] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.715639] usb usb3: Product: xHCI Host Controller [ 0.715781] usb usb3: Manufacturer: Linux 6.10.0-rc5+ xhci-hcd [ 0.715938] usb usb3: SerialNumber: 0000:00:14.0 [ 0.716249] hub 3-0:1.0: USB hub found [ 0.716419] hub 3-0:1.0: 10 ports detected [ 0.719995] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.10 [ 0.720175] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.720348] usb usb4: Product: xHCI Host Controller [ 0.720489] usb usb4: Manufacturer: Linux 6.10.0-rc5+ xhci-hcd [ 0.720707] usb usb4: SerialNumber: 0000:00:14.0 [ 0.720988] hub 4-0:1.0: USB hub found [ 0.721149] hub 4-0:1.0: 2 ports detected [ 0.721726] usbcore: registered new interface driver usblp [ 0.721880] usbcore: registered new interface driver usb-storage [ 0.722057] i8042: PNP: No PS/2 controller found. [ 0.722295] rtc_cmos 00:02: RTC can wake from S4 [ 0.722861] rtc_cmos 00:02: registered as rtc0 [ 0.723053] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram [ 0.723224] device-mapper: uevent: version 1.0.3 [ 0.723292] xen: registering gsi 18 triggering 0 polarity 1 [ 0.723366] Already setup the GSI :18 [ 0.723424] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 0.723673] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 0.723683] intel_pstate: CPU model not supported [ 0.723973] hid: raw HID events driver (C) Jiri Kosina [ 0.724208] usbcore: registered new interface driver usbhid [ 0.724349] usbhid: USB HID core driver [ 0.724753] Initializing XFRM netlink socket [ 0.724929] NET: Registered PF_INET6 protocol family [ 0.725367] Segment Routing with IPv6 [ 0.725510] In-situ OAM (IOAM) with IPv6 [ 0.725673] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.725915] NET: Registered PF_PACKET protocol family [ 0.726070] 9pnet: Installing 9P2000 support [ 0.726222] Key type dns_resolver registered [ 0.726586] IPI shorthand broadcast: enabled [ 0.728766] sched_clock: Marking stable (676003630, 51886032)->(735566900, -7677238) [ 0.729106] i2c i2c-0: Successfully instantiated SPD at 0x51 [ 0.729308] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.729569] registered taskstats version 1 [ 0.729709] Loading compiled-in X.509 certificates [ 0.730859] PM: Magic number: 12:362:960 [ 0.731071] printk: legacy console [netcon0] enabled [ 0.731215] netconsole: network logging started [ 0.731557] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 0.740046] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 0.740353] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 0.743106] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 0.743307] ALSA device list: [ 0.743444] No soundcards found. [ 0.910294] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.937938] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 0.953954] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 0.959526] ata1.00: ATA-8: TOSHIBA MG03ACA100, FL1D, max UDMA/100 [ 0.960476] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.961757] ata1.00: configured for UDMA/100 [ 0.961912] usb 3-9: new high-speed USB device number 2 using xhci_hcd [ 0.962028] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MG03ACA1 FL1D PQ: 0 ANSI: 5 [ 0.962528] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 0.962563] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 0.962967] sd 0:0:0:0: [sda] Write Protect is off [ 0.963109] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 0.963160] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.963411] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 1.066712] usb 1-1: New USB device found, idVendor=8087, idProduct=8000, bcdDevice= 0.05 [ 1.066929] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.067359] hub 1-1:1.0: USB hub found [ 1.067690] hub 1-1:1.0: 6 ports detected [ 1.082686] usb 2-1: New USB device found, idVendor=8087, idProduct=8008, bcdDevice= 0.05 [ 1.082859] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.083364] hub 2-1:1.0: USB hub found [ 1.083703] hub 2-1:1.0: 4 ports detected [ 1.088722] usb 3-9: New USB device found, idVendor=0624, idProduct=0248, bcdDevice= 0.00 [ 1.088900] usb 3-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.089037] usb 3-9: Product: Gadget USB HUB [ 1.089166] usb 3-9: Manufacturer: no manufacturer [ 1.089295] usb 3-9: SerialNumber: 0123456789 [ 1.090256] hub 3-9:1.0: USB hub found [ 1.090514] hub 3-9:1.0: 6 ports detected [ 1.151350] sda: sda1 sda2 < sda5 > [ 1.151822] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.270080] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.272904] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GTA0N, A3B0, max UDMA/100 [ 1.277719] ata5.00: configured for UDMA/100 [ 1.282781] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW GTA0N A3B0 PQ: 0 ANSI: 5 [ 1.305473] sr 4:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.305662] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.318307] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 1.318406] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 1.377944] usb 3-9.1: new high-speed USB device number 3 using xhci_hcd [ 1.465155] usb 3-9.1: New USB device found, idVendor=0624, idProduct=0249, bcdDevice= 0.00 [ 1.465336] usb 3-9.1: New USB device strings: Mfr=4, Product=5, SerialNumber=6 [ 1.465546] usb 3-9.1: Product: Keyboard/Mouse Function [ 1.465689] usb 3-9.1: Manufacturer: Avocent [ 1.465828] usb 3-9.1: SerialNumber: 20120917 [ 1.472820] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.0/0003:0624:0249.0001/input/input1 [ 1.525175] hid-generic 0003:0624:0249.0001: input,hidraw0: USB HID v1.00 Keyboard [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input0 [ 1.526293] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.1/0003:0624:0249.0002/input/input2 [ 1.526624] hid-generic 0003:0624:0249.0002: input,hidraw1: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input1 [ 1.527569] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.2/0003:0624:0249.0003/input/input3 [ 1.527908] hid-generic 0003:0624:0249.0003: input,hidraw2: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input2 [ 1.630222] ata6: SATA link down (SStatus 0 SControl 300) [ 1.631585] Freeing unused kernel image (initmem) memory: 2680K [ 1.631840] Write protecting the kernel read-only data: 24576k [ 1.645689] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 1.843451] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.843641] Run /init as init process [ 1.843782] with arguments: [ 1.843783] /init [ 1.843784] placeholder [ 1.843785] with environment: [ 1.843785] HOME=/ [ 1.843786] TERM=linux [ 2.071290] tg3 0000:01:00.1 enx549f3505fd8a: renamed from eth1 [ 2.074524] tg3 0000:01:00.0 enx549f3505fd88: renamed from eth0 [ 2.792686] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.026404] EXT4-fs (dm-0): mounted filesystem a98a8773-8b01-4f4c-a218-f426f8d8621d ro with ordered data mode. Quota mode: none. [ 6.482205] EXT4-fs (dm-0): re-mounted a98a8773-8b01-4f4c-a218-f426f8d8621d r/w. Quota mode: none. [ 7.394811] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 7.403231] EXT4-fs (sda1): mounted filesystem 3c563258-1c66-4cbe-9611-ab74abbedc9b r/w with ordered data mode. Quota mode: none. [ 7.468816] Adding 1949692k swap on /dev/mapper/godello1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 9.100455] xenbr0: port 1(enx549f3505fd88) entered blocking state [ 9.100672] xenbr0: port 1(enx549f3505fd88) entered disabled state [ 9.100823] tg3 0000:01:00.0 enx549f3505fd88: entered allmulticast mode [ 9.101011] tg3 0000:01:00.0 enx549f3505fd88: entered promiscuous mode [ 12.813695] tg3 0000:01:00.0 enx549f3505fd88: Link is up at 1000 Mbps, full duplex [ 12.813912] tg3 0000:01:00.0 enx549f3505fd88: Flow control is off for TX and off for RX [ 12.814084] tg3 0000:01:00.0 enx549f3505fd88: EEE is disabled [ 12.814324] xenbr0: port 1(enx549f3505fd88) entered blocking state [ 12.814470] xenbr0: port 1(enx549f3505fd88) entered forwarding state