[ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod1) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Fri Jun 28 14:24:55 UTC 2024 [ 0.000000] Command line: placeholder root=/dev/mapper/godello1--vg-root ro console=hvc0 [ 0.000000] Released 0 page(s) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009efff] usable [ 0.000000] Xen: [mem 0x000000000009f000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000020060fff] usable [ 0.000000] Xen: [mem 0x000000009573f000-0x0000000095bbefff] reserved [ 0.000000] Xen: [mem 0x0000000095bbf000-0x0000000095fbefff] ACPI NVS [ 0.000000] Xen: [mem 0x0000000095fbf000-0x0000000095ffefff] ACPI data [ 0.000000] Xen: [mem 0x0000000096000000-0x000000009fffffff] reserved [ 0.000000] Xen: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved [ 0.000000] Xen: [mem 0x00000000feb00000-0x00000000feb03fff] reserved [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] Xen: [mem 0x00000000fed10000-0x00000000fed19fff] reserved [ 0.000000] Xen: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] Xen: [mem 0x00000000fed90000-0x00000000fed90fff] reserved [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] Xen: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: Dell Inc. PowerEdge R220/081N4V, BIOS 1.1.4 05/06/2014 [ 0.000000] DMI: Memory slots populated: 1/4 [ 0.000000] Hypervisor detected: Xen PV [ 0.000022] Xen PV: Detected 4 vCPUS [ 0.000482] tsc: Detected 3092.838 MHz processor [ 0.000808] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000813] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000820] last_pfn = 0x20061 max_arch_pfn = 0x400000000 [ 0.000823] MTRR map: 4 entries (0 fixed + 4 variable; max 20), built from 10 variable MTRRs [ 0.000825] MTRRs set to read-only [ 0.000829] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC [ 0.000882] Kernel/User page tables isolation: disabled on XEN PV. [ 0.020118] RAMDISK: [mem 0x04000000-0x053a4fff] [ 0.020134] ACPI: Early table checksum verification disabled [ 0.021766] ACPI: RSDP 0x00000000000FE020 000024 (v02 DELL ) [ 0.021780] ACPI: XSDT 0x0000000095FCF188 0000E4 (v01 DELL PE_SC3 00000001 01000013) [ 0.021837] ACPI: FACP 0x0000000095FF7000 00010C (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.021919] ACPI: DSDT 0x0000000095FDF000 012335 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.021936] ACPI: FACS 0x0000000095FBD000 000040 [ 0.021951] ACPI: UEFI 0x0000000095FFD000 000236 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.021966] ACPI: UEFI 0x0000000095FFC000 000042 (v01 DELL PE_SC3 00000000 DELL 00040000) [ 0.021980] ACPI: ASF! 0x0000000095FFB000 0000A5 (v32 DELL PE_SC3 00000001 DELL 00040000) [ 0.021995] ACPI: ASPT 0x0000000095FFA000 000034 (v07 DELL PE_SC3 00000001 DELL 00040000) [ 0.022010] ACPI: BOOT 0x0000000095FF9000 000028 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022024] ACPI: DBGP 0x0000000095FF8000 000034 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022038] ACPI: HPET 0x0000000095FF6000 000038 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022053] ACPI: APIC 0x0000000095FF5000 000092 (v03 DELL PE_SC3 00000001 DELL 00040000) [ 0.022067] ACPI: MCFG 0x0000000095FF4000 00003C (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022083] ACPI: SLIC 0x0000000095FF3000 000176 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022097] ACPI: SSDT 0x0000000095FDC000 002028 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.022112] ACPI: SPMI 0x0000000095FDA000 000040 (v05 DELL PE_SC3 00000001 DELL 00040000) [ 0.022125] ACPI: SSDT 0x0000000095FD9000 000533 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022139] ACPI: SSDT 0x0000000095FD8000 000ACE (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022155] ACPI: SSDT 0x0000000095FD4000 003492 (v01 DELL PE_SC3 00003000 DELL 00040000) [ 0.022169] ACPI: SPCR 0x0000000095FF2000 000050 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022182] ACPI: RMAD 0x0000000095FD3000 000080 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022196] ACPI: SSDT 0x0000000095FD2000 000514 (v01 DELL PE_SC3 00001000 DELL 00040000) [ 0.022209] ACPI: FPDT 0x0000000095FD1000 000044 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022223] ACPI: HEST 0x0000000095FD0000 0000A8 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022238] ACPI: ERST 0x0000000095FCE000 000230 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022252] ACPI: BERT 0x0000000095FCD000 000030 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022266] ACPI: EINJ 0x0000000095FCC000 000150 (v01 DELL PE_SC3 00000001 DELL 00040000) [ 0.022273] ACPI: Reserving FACP table memory at [mem 0x95ff7000-0x95ff710b] [ 0.022275] ACPI: Reserving DSDT table memory at [mem 0x95fdf000-0x95ff1334] [ 0.022276] ACPI: Reserving FACS table memory at [mem 0x95fbd000-0x95fbd03f] [ 0.022276] ACPI: Reserving UEFI table memory at [mem 0x95ffd000-0x95ffd235] [ 0.022278] ACPI: Reserving UEFI table memory at [mem 0x95ffc000-0x95ffc041] [ 0.022278] ACPI: Reserving ASF! table memory at [mem 0x95ffb000-0x95ffb0a4] [ 0.022279] ACPI: Reserving ASPT table memory at [mem 0x95ffa000-0x95ffa033] [ 0.022280] ACPI: Reserving BOOT table memory at [mem 0x95ff9000-0x95ff9027] [ 0.022281] ACPI: Reserving DBGP table memory at [mem 0x95ff8000-0x95ff8033] [ 0.022282] ACPI: Reserving HPET table memory at [mem 0x95ff6000-0x95ff6037] [ 0.022282] ACPI: Reserving APIC table memory at [mem 0x95ff5000-0x95ff5091] [ 0.022283] ACPI: Reserving MCFG table memory at [mem 0x95ff4000-0x95ff403b] [ 0.022284] ACPI: Reserving SLIC table memory at [mem 0x95ff3000-0x95ff3175] [ 0.022284] ACPI: Reserving SSDT table memory at [mem 0x95fdc000-0x95fde027] [ 0.022285] ACPI: Reserving SPMI table memory at [mem 0x95fda000-0x95fda03f] [ 0.022286] ACPI: Reserving SSDT table memory at [mem 0x95fd9000-0x95fd9532] [ 0.022287] ACPI: Reserving SSDT table memory at [mem 0x95fd8000-0x95fd8acd] [ 0.022288] ACPI: Reserving SSDT table memory at [mem 0x95fd4000-0x95fd7491] [ 0.022289] ACPI: Reserving SPCR table memory at [mem 0x95ff2000-0x95ff204f] [ 0.022289] ACPI: Reserving RMAD table memory at [mem 0x95fd3000-0x95fd307f] [ 0.022290] ACPI: Reserving SSDT table memory at [mem 0x95fd2000-0x95fd2513] [ 0.022291] ACPI: Reserving FPDT table memory at [mem 0x95fd1000-0x95fd1043] [ 0.022292] ACPI: Reserving HEST table memory at [mem 0x95fd0000-0x95fd00a7] [ 0.022293] ACPI: Reserving ERST table memory at [mem 0x95fce000-0x95fce22f] [ 0.022294] ACPI: Reserving BERT table memory at [mem 0x95fcd000-0x95fcd02f] [ 0.022294] ACPI: Reserving EINJ table memory at [mem 0x95fcc000-0x95fcc14f] [ 0.022426] APIC: Switched APIC routing to: Xen PV [ 0.025501] Zone ranges: [ 0.025504] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.025507] DMA32 [mem 0x0000000001000000-0x0000000020060fff] [ 0.025508] Normal empty [ 0.025509] Movable zone start for each node [ 0.025510] Early memory node ranges [ 0.025510] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.025513] node 0: [mem 0x0000000000100000-0x0000000020060fff] [ 0.025514] Initmem setup node 0 [mem 0x0000000000001000-0x0000000020060fff] [ 0.025524] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.025602] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.028974] On node 0, zone DMA32: 32671 pages in unavailable ranges [ 0.028980] p2m virtual area at (____ptrval____), size is 40000000 [ 0.121391] Remapped 97 page(s) [ 0.121973] ACPI: PM-Timer IO Port: 0x1808 [ 0.122051] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.122087] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.122103] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.122107] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.122133] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.122139] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.122149] ACPI: SPCR: SPCR table version 1 [ 0.122153] ACPI: SPCR: console: uart,io,0x3f8,115200 [ 0.122157] CPU topo: 8 possible CPUs exceed the limit of 4 [ 0.122167] CPU topo: Max. logical packages: 1 [ 0.122168] CPU topo: Max. logical dies: 1 [ 0.122169] CPU topo: Max. dies per package: 1 [ 0.122176] CPU topo: Max. threads per core: 1 [ 0.122177] CPU topo: Num. cores per package: 4 [ 0.122178] CPU topo: Num. threads per package: 4 [ 0.122179] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs [ 0.122196] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.122198] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] [ 0.122201] [mem 0x20061000-0x9573efff] available for PCI devices [ 0.122206] Booting kernel on Xen [ 0.122207] Xen version: 4.19-unstable (preserve-AD) [ 0.122212] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.128202] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.129138] percpu: Embedded 57 pages/cpu s194408 r8192 d30872 u524288 [ 0.129145] pcpu-alloc: s194408 r8192 d30872 u524288 alloc=1*2097152 [ 0.129149] pcpu-alloc: [0] 0 1 2 3 [ 0.129222] xen: PV spinlocks enabled [ 0.129229] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.129233] Kernel command line: placeholder root=/dev/mapper/godello1--vg-root ro console=hvc0 [ 0.129296] Unknown kernel command line parameters "placeholder", will be passed to user space. [ 0.129318] random: crng init done [ 0.129479] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.129562] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.130163] Built 1 zonelists, mobility grouping on. Total pages: 131071 [ 0.130169] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.130173] software IO TLB: area num 4. [ 0.216639] Memory: 386520K/524284K available (16384K kernel code, 2753K rwdata, 6164K rodata, 2680K init, 1864K bss, 137512K reserved, 0K cma-reserved) [ 0.216772] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.219237] Dynamic Preempt: voluntary [ 0.219368] rcu: Preemptible hierarchical RCU implementation. [ 0.219369] rcu: RCU event tracing is enabled. [ 0.219370] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.219371] Trampoline variant of Tasks RCU enabled. [ 0.219372] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.219373] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.219392] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.227926] NR_IRQS: 4352, nr_irqs: 456, preallocated irqs: 16 [ 0.228074] xen:events: Using FIFO-based ABI [ 0.228102] xen: --> pirq=1 -> irq=1 (gsi=1) [ 0.228108] xen: --> pirq=2 -> irq=2 (gsi=2) [ 0.228114] xen: --> pirq=3 -> irq=3 (gsi=3) [ 0.228119] xen: --> pirq=4 -> irq=4 (gsi=4) [ 0.228124] xen: --> pirq=5 -> irq=5 (gsi=5) [ 0.228134] xen: --> pirq=6 -> irq=6 (gsi=6) [ 0.228140] xen: --> pirq=7 -> irq=7 (gsi=7) [ 0.228146] xen: --> pirq=8 -> irq=8 (gsi=8) [ 0.228151] xen: --> pirq=9 -> irq=9 (gsi=9) [ 0.228157] xen: --> pirq=10 -> irq=10 (gsi=10) [ 0.228163] xen: --> pirq=11 -> irq=11 (gsi=11) [ 0.228168] xen: --> pirq=12 -> irq=12 (gsi=12) [ 0.228174] xen: --> pirq=13 -> irq=13 (gsi=13) [ 0.228179] xen: --> pirq=14 -> irq=14 (gsi=14) [ 0.228185] xen: --> pirq=15 -> irq=15 (gsi=15) [ 0.228197] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.237349] Console: colour VGA+ 80x25 [ 0.237354] printk: legacy console [tty0] enabled [ 0.258155] printk: legacy console [hvc0] enabled [ 0.259289] ACPI: Core revision 20240322 [ 0.279619] clocksource: xen: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns [ 0.279826] Xen: using vcpuop timer interface [ 0.279837] installing Xen timer for CPU 0 [ 0.280039] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2c94d9afcf4, max_idle_ns: 440795231738 ns [ 0.280294] Calibrating delay loop (skipped), value calculated using timer frequency.. 6185.67 BogoMIPS (lpj=3092838) [ 0.280629] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024 [ 0.280774] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4 [ 0.281313] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.281492] Spectre V2 : Mitigation: Retpolines [ 0.281634] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.281811] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.281956] Spectre V2 : Enabling Restricted Speculation for firmware calls [ 0.282102] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.282280] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.282298] MDS: Mitigation: Clear CPU buffers [ 0.282439] MMIO Stale Data: Unknown: No mitigations [ 0.282575] SRBDS: Unknown: Dependent on hypervisor status [ 0.282741] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.282914] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.283059] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.283205] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.283294] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.306179] Freeing SMP alternatives memory: 40K [ 0.306298] pid_max: default: 32768 minimum: 301 [ 0.306468] LSM: initializing lsm=capability,selinux [ 0.306612] SELinux: Initializing. [ 0.306807] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.306983] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.308402] cpu 0 spinlock event irq 25 [ 0.308547] VPMU disabled by hypervisor. [ 0.309075] Performance Events: unsupported p6 CPU model 60 no PMU driver, software events only. [ 0.309259] signal: max sigframe size: 1776 [ 0.309356] rcu: Hierarchical SRCU implementation. [ 0.309493] rcu: Max phase no-delay instances is 400. [ 0.310056] smp: Bringing up secondary CPUs ... [ 0.310397] installing Xen timer for CPU 1 [ 0.310817] installing Xen timer for CPU 2 [ 0.311181] installing Xen timer for CPU 3 [ 0.053091] [Firmware Bug]: CPU 1: APIC ID mismatch. CPUID: 0x0001 APIC: 0x0002 [ 0.311382] cpu 1 spinlock event irq 45 [ 0.053091] [Firmware Bug]: CPU 2: APIC ID mismatch. CPUID: 0x0002 APIC: 0x0004 [ 0.311671] cpu 2 spinlock event irq 46 [ 0.053091] [Firmware Bug]: CPU 3: APIC ID mismatch. CPUID: 0x0003 APIC: 0x0006 [ 0.312339] cpu 3 spinlock event irq 47 [ 0.312656] smp: Brought up 1 node, 4 CPUs [ 0.313607] devtmpfs: initialized [ 0.313607] x86/mm: Memory block size: 128MB [ 0.314310] ACPI: PM: Registering ACPI NVS region [mem 0x95bbf000-0x95fbefff] (4194304 bytes) [ 0.314586] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.314765] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.315032] PM: RTC time: 15:29:36, date: 2024-06-28 [ 0.315344] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.315517] xen:grant_table: Grant tables using version 1 layout [ 0.315692] Grant table initialized [ 0.315954] audit: initializing netlink subsys (disabled) [ 0.316133] audit: type=2000 audit(1719588577.122:1): state=initialized audit_enabled=0 res=1 [ 0.316345] thermal_sys: Registered thermal governor 'step_wise' [ 0.316347] thermal_sys: Registered thermal governor 'user_space' [ 0.316526] Simple Boot Flag at 0x44 set to 0x1 [ 0.316826] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.317143] PCI: ECAM [mem 0xf0000000-0xf7ffffff] (base 0xf0000000) for domain 0000 [bus 00-7f] [ 0.317301] PCI: ECAM [mem 0xf0000000-0xf7ffffff] reserved as E820 entry [ 0.364869] PCI: Using configuration type 1 for base access [ 0.365099] PCI: Dell System detected, enabling pci=bfsort. [ 0.365365] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.365527] ACPI: Added _OSI(Module Device) [ 0.365527] ACPI: Added _OSI(Processor Device) [ 0.365600] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.366300] ACPI: Added _OSI(Processor Aggregator Device) [ 0.376728] ACPI: 6 ACPI AML tables successfully acquired and loaded [ 0.377503] xen: registering gsi 9 triggering 0 polarity 0 [ 0.377718] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.381687] ACPI: Dynamic OEM Table Load: [ 0.381834] ACPI: SSDT 0xFFFF88800399E000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20120816) [ 0.383009] ACPI: Dynamic OEM Table Load: [ 0.383154] ACPI: SSDT 0xFFFF888003ADC800 0005AA (v01 PmRef ApIst 00003000 INTL 20120816) [ 0.383921] ACPI: Dynamic OEM Table Load: [ 0.384063] ACPI: SSDT 0xFFFF888003981200 000119 (v01 PmRef ApCst 00003000 INTL 20120816) [ 0.385134] ACPI: _OSC evaluated successfully for all CPUs [ 0.385437] ACPI: Interpreter enabled [ 0.385585] ACPI: PM: (supports S0 S4 S5) [ 0.385722] ACPI: Using IOAPIC for interrupt routing [ 0.385884] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.386062] PCI: Using E820 reservations for host bridge windows [ 0.386450] ACPI: Enabled 11 GPEs in block 00 to 3F [ 0.394285] acpi ABCD0000:00: ACPI dock station (docks/bays count: 1) [ 0.402332] ACPI: \_TZ_.FN00: New power resource [ 0.402508] ACPI: \_TZ_.FN01: New power resource [ 0.402682] ACPI: \_TZ_.FN02: New power resource [ 0.402857] ACPI: \_TZ_.FN03: New power resource [ 0.403029] ACPI: \_TZ_.FN04: New power resource [ 0.403887] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e]) [ 0.404037] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.405048] acpi PNP0A08:00: _OSC: OS now controls [PME PCIeCapability LTR] [ 0.405199] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration [ 0.405771] PCI host bridge to bus 0000:00 [ 0.405911] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.406057] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.406202] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.406296] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xfeafffff window] [ 0.406470] pci_bus 0000:00: root bus resource [bus 00-7e] [ 0.406649] pci 0000:00:00.0: [8086:0c08] type 00 class 0x060000 conventional PCI endpoint [ 0.407224] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330 conventional PCI endpoint [ 0.407371] pci 0000:00:14.0: BAR 0 [mem 0xa2b00000-0xa2b0ffff 64bit] [ 0.407789] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 0.408164] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320 conventional PCI endpoint [ 0.408358] pci 0000:00:1a.0: BAR 0 [mem 0xa2b12000-0xa2b123ff] [ 0.408814] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 0.409140] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400 PCIe Root Port [ 0.409418] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.409616] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.410016] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.410239] pci 0000:00:1c.0: Enabling MPC IRBNCE [ 0.410305] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled [ 0.410793] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400 PCIe Root Port [ 0.411078] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.411240] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.411339] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.411734] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.411955] pci 0000:00:1c.2: Enabling MPC IRBNCE [ 0.412102] pci 0000:00:1c.2: Intel PCH root port ACS workaround enabled [ 0.412611] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320 conventional PCI endpoint [ 0.412841] pci 0000:00:1d.0: BAR 0 [mem 0xa2b11000-0xa2b113ff] [ 0.413305] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 0.413642] pci 0000:00:1f.0: [8086:8c52] type 00 class 0x060100 conventional PCI endpoint [ 0.414328] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601 conventional PCI endpoint [ 0.414560] pci 0000:00:1f.2: BAR 0 [io 0x3048-0x304f] [ 0.414734] pci 0000:00:1f.2: BAR 1 [io 0x3054-0x3057] [ 0.414906] pci 0000:00:1f.2: BAR 2 [io 0x3040-0x3047] [ 0.415070] pci 0000:00:1f.2: BAR 3 [io 0x3050-0x3053] [ 0.415246] pci 0000:00:1f.2: BAR 4 [io 0x3020-0x303f] [ 0.415330] pci 0000:00:1f.2: BAR 5 [mem 0xa2b10000-0xa2b107ff] [ 0.415641] pci 0000:00:1f.2: PME# supported from D3hot [ 0.415934] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500 conventional PCI endpoint [ 0.416183] pci 0000:00:1f.3: BAR 0 [mem 0xa2b13000-0xa2b130ff 64bit] [ 0.416391] pci 0000:00:1f.3: BAR 4 [io 0x3000-0x301f] [ 0.416974] pci 0000:01:00.0: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.417355] pci 0000:01:00.0: BAR 0 [mem 0xa2a30000-0xa2a3ffff 64bit pref] [ 0.417620] pci 0000:01:00.0: BAR 2 [mem 0xa2a40000-0xa2a4ffff 64bit pref] [ 0.417877] pci 0000:01:00.0: BAR 4 [mem 0xa2a50000-0xa2a5ffff 64bit pref] [ 0.418115] pci 0000:01:00.0: ROM [mem 0x00000000-0x0003ffff pref] [ 0.418767] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.419517] pci 0000:01:00.1: [14e4:165f] type 00 class 0x020000 PCIe Endpoint [ 0.419848] pci 0000:01:00.1: BAR 0 [mem 0xa2a00000-0xa2a0ffff 64bit pref] [ 0.420110] pci 0000:01:00.1: BAR 2 [mem 0xa2a10000-0xa2a1ffff 64bit pref] [ 0.420405] pci 0000:01:00.1: BAR 4 [mem 0xa2a20000-0xa2a2ffff 64bit pref] [ 0.420645] pci 0000:01:00.1: ROM [mem 0x00000000-0x0003ffff pref] [ 0.421275] pci 0000:01:00.1: PME# supported from D0 D3hot D3cold [ 0.422006] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.422915] pci 0000:02:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Upstream Port [ 0.424198] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.424531] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.424990] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.426855] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.428450] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.429947] pci 0000:03:00.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.431444] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.431856] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.432339] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.434447] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold [ 0.436406] pci 0000:03:01.0: [1912:0013] type 01 class 0x060400 PCIe Switch Downstream Port [ 0.437802] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.438193] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.440811] pci 0000:03:01.0: PME# supported from D0 D3hot D3cold [ 0.444572] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.446374] pci 0000:04:00.0: [1912:0012] type 01 class 0x060400 PCIe to PCI/PCI-X bridge [ 0.447807] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.448198] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.448647] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.452076] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.453627] pci_bus 0000:05: extended config space not accessible [ 0.454009] pci 0000:05:00.0: [102b:0534] type 00 class 0x030000 conventional PCI endpoint [ 0.454665] pci 0000:05:00.0: BAR 0 [mem 0xa1000000-0xa1ffffff pref] [ 0.455071] pci 0000:05:00.0: BAR 1 [mem 0xa2800000-0xa2803fff] [ 0.455446] pci 0000:05:00.0: BAR 2 [mem 0xa2000000-0xa27fffff] [ 0.456907] pci 0000:05:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.460294] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.462565] pci 0000:06:00.0: [1912:0011] type 00 class 0x050000 conventional PCI endpoint [ 0.463233] pci 0000:06:00.0: BAR 0 [mem 0xa2901000-0xa2901fff] [ 0.463562] pci 0000:06:00.0: BAR 1 [mem 0xa2900000-0xa290007f] [ 0.465979] pci 0000:06:00.0: PME# supported from D3hot [ 0.467116] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.468839] pci_bus 0000:00: on NUMA node 0 [ 0.469049] xen: registering gsi 13 triggering 1 polarity 0 [ 0.470021] ACPI: PCI: Interrupt link LNKA configured for IRQ 10 [ 0.470238] ACPI: PCI: Interrupt link LNKB configured for IRQ 11 [ 0.470368] ACPI: PCI: Interrupt link LNKC configured for IRQ 10 [ 0.470587] ACPI: PCI: Interrupt link LNKD configured for IRQ 10 [ 0.470806] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.470954] ACPI: PCI: Interrupt link LNKE disabled [ 0.471147] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.471289] ACPI: PCI: Interrupt link LNKF disabled [ 0.471502] ACPI: PCI: Interrupt link LNKG configured for IRQ 0 [ 0.471646] ACPI: PCI: Interrupt link LNKG disabled [ 0.471853] ACPI: PCI: Interrupt link LNKH configured for IRQ 11 [ 0.472510] xen:balloon: Initialising balloon driver [ 0.472670] iommu: Default domain type: Translated [ 0.472670] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.472680] SCSI subsystem initialized [ 0.473310] libata version 3.00 loaded. [ 0.473330] ACPI: bus type USB registered [ 0.473477] usbcore: registered new interface driver usbfs [ 0.473621] usbcore: registered new interface driver hub [ 0.473761] usbcore: registered new device driver usb [ 0.473905] pps_core: LinuxPPS API ver. 1 registered [ 0.474045] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.474230] PTP clock support registered [ 0.474320] Advanced Linux Sound Architecture Driver Initialized. [ 0.474623] NetLabel: Initializing [ 0.474762] NetLabel: domain hash size = 128 [ 0.474900] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.475052] NetLabel: unlabeled traffic allowed by default [ 0.475322] PCI: Using ACPI for IRQ routing [ 0.491645] PCI: pci_cache_line_size set to 64 bytes [ 0.492283] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] [ 0.492285] e820: reserve RAM buffer [mem 0x20061000-0x23ffffff] [ 0.492453] pci 0000:05:00.0: vgaarb: setting as boot VGA device [ 0.492625] pci 0000:05:00.0: vgaarb: bridge control possible [ 0.492766] pci 0000:05:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.492942] vgaarb: loaded [ 0.493152] clocksource: Switched to clocksource tsc-early [ 0.493152] VFS: Disk quotas dquot_6.6.0 [ 0.493152] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.493152] hugetlbfs: disabling because there are no supported hugepage sizes [ 0.493152] pnp: PnP ACPI init [ 0.493227] system 00:00: [io 0x0680-0x069f] has been reserved [ 0.493372] system 00:00: [io 0xffff] has been reserved [ 0.493445] system 00:00: [io 0xffff] has been reserved [ 0.493445] system 00:00: [io 0xffff] has been reserved [ 0.493445] system 00:00: [io 0x1800-0x18fe] has been reserved [ 0.493445] system 00:00: [io 0x164e-0x164f] has been reserved [ 0.493445] system 00:01: [io 0x0800-0x087f] has been reserved [ 0.493445] xen: registering gsi 8 triggering 1 polarity 0 [ 0.494355] system 00:03: [io 0x1854-0x1857] has been reserved [ 0.494773] xen: registering gsi 3 triggering 1 polarity 0 [ 0.495034] xen: registering gsi 4 triggering 1 polarity 0 [ 0.495037] Already setup the GSI :4 [ 0.495352] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.495500] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved [ 0.495646] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.495789] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.495936] system 00:06: [mem 0xf0000000-0xf7ffffff] has been reserved [ 0.496081] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved [ 0.496228] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved [ 0.496382] system 00:06: [mem 0xff000000-0xffffffff] could not be reserved [ 0.496529] system 00:06: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.496674] system 00:06: [mem 0xa0000000-0xa0000fff] has been reserved [ 0.496821] system 00:06: [mem 0xa0020000-0xa002ffff] has been reserved [ 0.497808] pnp: PnP ACPI: found 7 devices [ 0.519549] PM-Timer failed consistency check (0xffffff) - aborting. [ 0.519733] NET: Registered PF_INET protocol family [ 0.519900] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.520224] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.520414] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.520602] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.520804] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.520999] TCP: Hash tables configured (established 4096 bind 4096) [ 0.521164] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.521324] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.521491] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.521800] RPC: Registered named UNIX socket transport module. [ 0.521945] RPC: Registered udp transport module. [ 0.522084] RPC: Registered tcp transport module. [ 0.522224] RPC: Registered tcp-with-tls transport module. [ 0.522372] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.522818] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff]: assigned [ 0.522997] pci 0000:01:00.0: ROM [mem 0xa0100000-0xa013ffff pref]: assigned [ 0.523145] pci 0000:01:00.1: ROM [mem 0xa0140000-0xa017ffff pref]: assigned [ 0.523301] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.523458] pci 0000:00:1c.0: bridge window [mem 0xa0100000-0xa01fffff] [ 0.523613] pci 0000:00:1c.0: bridge window [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.523799] pci 0000:04:00.0: PCI bridge to [bus 05] [ 0.524084] pci 0000:04:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.524334] pci 0000:04:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.524700] pci 0000:03:00.0: PCI bridge to [bus 04-05] [ 0.524986] pci 0000:03:00.0: bridge window [mem 0xa2000000-0xa28fffff] [ 0.525217] pci 0000:03:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.525593] pci 0000:03:01.0: PCI bridge to [bus 06] [ 0.525874] pci 0000:03:01.0: bridge window [mem 0xa2900000-0xa29fffff] [ 0.526391] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.526667] pci 0000:02:00.0: bridge window [mem 0xa2000000-0xa29fffff] [ 0.526904] pci 0000:02:00.0: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.527336] pci 0000:00:1c.2: PCI bridge to [bus 02-06] [ 0.527492] pci 0000:00:1c.2: bridge window [mem 0xa2000000-0xa29fffff] [ 0.527643] pci 0000:00:1c.2: bridge window [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.527834] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.527973] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.528116] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.528255] pci_bus 0000:00: resource 7 [mem 0xa0000000-0xfeafffff window] [ 0.528401] pci_bus 0000:01: resource 1 [mem 0xa0100000-0xa01fffff] [ 0.528546] pci_bus 0000:01: resource 2 [mem 0xa2a00000-0xa2afffff 64bit pref] [ 0.528718] pci_bus 0000:02: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.528863] pci_bus 0000:02: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.529031] pci_bus 0000:03: resource 1 [mem 0xa2000000-0xa29fffff] [ 0.529175] pci_bus 0000:03: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.529352] pci_bus 0000:04: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.529490] pci_bus 0000:04: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.529657] pci_bus 0000:05: resource 1 [mem 0xa2000000-0xa28fffff] [ 0.529801] pci_bus 0000:05: resource 2 [mem 0xa1000000-0xa1ffffff 64bit pref] [ 0.529973] pci_bus 0000:06: resource 1 [mem 0xa2900000-0xa29fffff] [ 0.530241] xen: registering gsi 16 triggering 0 polarity 1 [ 0.530261] xen: --> pirq=16 -> irq=16 (gsi=16) [ 0.531709] xen: registering gsi 16 triggering 0 polarity 1 [ 0.531714] Already setup the GSI :16 [ 0.543418] pci 0000:00:1a.0: quirk_usb_early_handoff+0x0/0x7c0 took 11480 usecs [ 0.543664] xen: registering gsi 23 triggering 0 polarity 1 [ 0.543685] xen: --> pirq=23 -> irq=23 (gsi=23) [ 0.555420] pci 0000:00:1d.0: quirk_usb_early_handoff+0x0/0x7c0 took 11523 usecs [ 0.555900] PCI: CLS 64 bytes, default 64 [ 0.556066] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.556114] Unpacking initramfs... [ 0.556211] software IO TLB: mapped [mem 0x000000001b180000-0x000000001f180000] (64MB) [ 0.558558] kvm_intel: VMX not supported by CPU 0 [ 0.558723] kvm_amd: CPU 0 isn't AMD or Hygon [ 0.558864] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c94d9afcf4, max_idle_ns: 440795231738 ns [ 0.559119] clocksource: Switched to clocksource tsc [ 0.562984] Initialise system trusted keyrings [ 0.563219] workingset: timestamp_bits=62 max_order=17 bucket_order=0 [ 0.563511] NFS: Registering the id_resolver key type [ 0.563657] Key type id_resolver registered [ 0.563789] Key type id_legacy registered [ 0.563966] 9p: Installing v9fs 9p2000 file system support [ 0.576321] Key type asymmetric registered [ 0.576478] Asymmetric key parser 'x509' registered [ 0.576642] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.576822] io scheduler mq-deadline registered [ 0.576961] io scheduler kyber registered [ 0.577391] xen: registering gsi 16 triggering 0 polarity 1 [ 0.577398] Already setup the GSI :16 [ 0.577759] pcieport 0000:00:1c.0: PME: Signaling with IRQ 50 [ 0.578143] xen: registering gsi 18 triggering 0 polarity 1 [ 0.578160] xen: --> pirq=18 -> irq=18 (gsi=18) [ 0.578338] pcieport 0000:00:1c.2: PME: Signaling with IRQ 51 [ 0.582691] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.582924] ACPI: button: Power Button [PWRF] [ 0.583436] Monitor-Mwait will be used to enter C-1 state [ 0.583447] Monitor-Mwait will be used to enter C-2 state [ 0.583451] ACPI: \_PR_.CPU0: Found 2 idle states [ 0.583770] ACPI: \_PR_.CPU1: Found 2 idle states [ 0.586278] ACPI: \_PR_.CPU2: Found 2 idle states [ 0.586755] ACPI: \_PR_.CPU3: Found 2 idle states [ 0.587303] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.587470] ACPI: thermal: Thermal Zone [TZ00] (28 C) [ 0.587823] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.587967] ACPI: thermal: Thermal Zone [TZ01] (30 C) [ 0.588382] xen:xen_evtchn: Event-channel device installed [ 0.588592] xen_pciback: backend is vpci [ 0.589168] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.589443] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 0.590152] hpet_acpi_add: no address or irqs in _CRS [ 0.590348] Non-volatile memory driver v1.3 [ 0.591747] loop: module loaded [ 0.595371] ahci 0000:00:1f.2: version 3.0 [ 0.595464] xen: registering gsi 19 triggering 0 polarity 1 [ 0.595490] xen: --> pirq=19 -> irq=19 (gsi=19) [ 0.595669] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled [ 0.595853] ahci 0000:00:1f.2: AHCI vers 0001.0300, 32 command slots, 6 Gbps, SATA mode [ 0.596029] ahci 0000:00:1f.2: 3/6 ports implemented (port mask 0x31) [ 0.596188] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst [ 0.602590] scsi host0: ahci [ 0.602916] scsi host1: ahci [ 0.603195] scsi host2: ahci [ 0.603459] scsi host3: ahci [ 0.603736] scsi host4: ahci [ 0.603994] scsi host5: ahci [ 0.604173] ata1: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10100 irq 53 lpm-pol 0 [ 0.604350] ata2: DUMMY [ 0.604482] ata3: DUMMY [ 0.604612] ata4: DUMMY [ 0.604742] ata5: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10300 irq 53 lpm-pol 0 [ 0.604920] ata6: SATA max UDMA/133 abar m2048@0xa2b10000 port 0xa2b10380 irq 53 lpm-pol 0 [ 0.605295] tun: Universal TUN/TAP device driver, 1.6 [ 0.605624] xen: registering gsi 16 triggering 0 polarity 1 [ 0.605630] Already setup the GSI :16 [ 0.637398] Freeing initrd memory: 20116K [ 0.639539] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:88 [ 0.639730] tg3 0000:01:00.0 eth0: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.639911] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.640084] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.640651] xen: registering gsi 17 triggering 0 polarity 1 [ 0.640675] xen: --> pirq=17 -> irq=17 (gsi=17) [ 0.688282] tg3 0000:01:00.1 eth1: Tigon3 [partno(BCM95720) rev 5720000] (PCI Express) MAC address 54:9f:35:05:fd:8a [ 0.688475] tg3 0000:01:00.1 eth1: attached PHY is 5720C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 0.688658] tg3 0000:01:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 0.688834] tg3 0000:01:00.1 eth1: dma_rwctrl[00000001] dma_mask[64-bit] [ 0.689329] e100: Intel(R) PRO/100 Network Driver [ 0.689470] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.689622] sky2: driver version 1.30 [ 0.689778] xen_netfront: Initialising Xen virtual ethernet driver [ 0.690191] xen: registering gsi 16 triggering 0 polarity 1 [ 0.690198] Already setup the GSI :16 [ 0.690202] xen: registering gsi 16 triggering 0 polarity 1 [ 0.690256] xen: registering gsi 23 triggering 0 polarity 1 [ 0.690261] Already setup the GSI :23 [ 0.690321] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 0.690417] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.690466] Already setup the GSI :16 [ 0.690505] ehci-pci 0000:00:1d.0: debug port 2 [ 0.695076] ehci-pci 0000:00:1d.0: irq 23, io mem 0xa2b11000 [ 0.702129] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 0.702344] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.702526] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.702699] usb usb1: Product: EHCI Host Controller [ 0.702838] usb usb1: Manufacturer: Linux 6.10.0-rc5+ ehci_hcd [ 0.702976] usb usb1: SerialNumber: 0000:00:1d.0 [ 0.703319] hub 1-0:1.0: USB hub found [ 0.703471] hub 1-0:1.0: 2 ports detected [ 0.703798] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 0.704051] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 2 [ 0.704270] ehci-pci 0000:00:1a.0: debug port 2 [ 0.708400] ehci-pci 0000:00:1a.0: irq 16, io mem 0xa2b12000 [ 0.715152] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 0.715357] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.715531] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.715704] usb usb2: Product: EHCI Host Controller [ 0.715843] usb usb2: Manufacturer: Linux 6.10.0-rc5+ ehci_hcd [ 0.715986] usb usb2: SerialNumber: 0000:00:1a.0 [ 0.716274] hub 2-0:1.0: USB hub found [ 0.716457] hub 2-0:1.0: 2 ports detected [ 0.716767] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.717000] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 [ 0.718275] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810 [ 0.718718] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 0.718930] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 [ 0.719116] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed [ 0.719353] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.10 [ 0.719564] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.719732] usb usb3: Product: xHCI Host Controller [ 0.719872] usb usb3: Manufacturer: Linux 6.10.0-rc5+ xhci-hcd [ 0.720014] usb usb3: SerialNumber: 0000:00:14.0 [ 0.720310] hub 3-0:1.0: USB hub found [ 0.720469] hub 3-0:1.0: 10 ports detected [ 0.723854] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.10 [ 0.724033] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.724252] usb usb4: Product: xHCI Host Controller [ 0.724392] usb usb4: Manufacturer: Linux 6.10.0-rc5+ xhci-hcd [ 0.724535] usb usb4: SerialNumber: 0000:00:14.0 [ 0.724821] hub 4-0:1.0: USB hub found [ 0.724974] hub 4-0:1.0: 2 ports detected [ 0.725518] usbcore: registered new interface driver usblp [ 0.725706] usbcore: registered new interface driver usb-storage [ 0.725872] i8042: PNP: No PS/2 controller found. [ 0.726118] rtc_cmos 00:02: RTC can wake from S4 [ 0.726684] rtc_cmos 00:02: registered as rtc0 [ 0.726867] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram [ 0.727038] device-mapper: uevent: version 1.0.3 [ 0.727112] xen: registering gsi 18 triggering 0 polarity 1 [ 0.727193] Already setup the GSI :18 [ 0.727281] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 0.727439] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt [ 0.727526] intel_pstate: CPU model not supported [ 0.727808] hid: raw HID events driver (C) Jiri Kosina [ 0.728041] usbcore: registered new interface driver usbhid [ 0.728194] usbhid: USB HID core driver [ 0.728593] Initializing XFRM netlink socket [ 0.728800] NET: Registered PF_INET6 protocol family [ 0.729260] Segment Routing with IPv6 [ 0.729405] In-situ OAM (IOAM) with IPv6 [ 0.729559] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.729790] NET: Registered PF_PACKET protocol family [ 0.729948] 9pnet: Installing 9P2000 support [ 0.730109] Key type dns_resolver registered [ 0.732325] IPI shorthand broadcast: enabled [ 0.732745] i2c i2c-0: Successfully instantiated SPD at 0x51 [ 0.734508] sched_clock: Marking stable (682004587, 52091354)->(743268233, -9172292) [ 0.734993] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.735268] registered taskstats version 1 [ 0.735406] Loading compiled-in X.509 certificates [ 0.736590] PM: Magic number: 12:621:488 [ 0.736793] printk: legacy console [netcon0] enabled [ 0.736934] netconsole: network logging started [ 0.737280] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 0.745526] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 0.745867] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 0.748038] ALSA device list: [ 0.748181] No soundcards found. [ 0.748733] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid [ 0.911541] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.939152] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 0.955160] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 0.959318] ata1.00: ATA-8: TOSHIBA MG03ACA100, FL1D, max UDMA/100 [ 0.960196] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.961702] ata1.00: configured for UDMA/100 [ 0.961974] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MG03ACA1 FL1D PQ: 0 ANSI: 5 [ 0.962746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 0.962770] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 0.963117] sd 0:0:0:0: [sda] Write Protect is off [ 0.963255] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 0.963275] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.963484] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 0.964105] usb 3-9: new high-speed USB device number 2 using xhci_hcd [ 1.067568] usb 1-1: New USB device found, idVendor=8087, idProduct=8000, bcdDevice= 0.05 [ 1.067744] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.068255] hub 1-1:1.0: USB hub found [ 1.068572] hub 1-1:1.0: 6 ports detected [ 1.083730] usb 2-1: New USB device found, idVendor=8087, idProduct=8008, bcdDevice= 0.05 [ 1.083896] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.084346] hub 2-1:1.0: USB hub found [ 1.084560] hub 2-1:1.0: 4 ports detected [ 1.091143] usb 3-9: New USB device found, idVendor=0624, idProduct=0248, bcdDevice= 0.00 [ 1.091309] usb 3-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.091445] usb 3-9: Product: Gadget USB HUB [ 1.091576] usb 3-9: Manufacturer: no manufacturer [ 1.091704] usb 3-9: SerialNumber: 0123456789 [ 1.092649] hub 3-9:1.0: USB hub found [ 1.092869] hub 3-9:1.0: 6 ports detected [ 1.149951] sda: sda1 sda2 < sda5 > [ 1.150411] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.271492] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.274352] ata5.00: ATAPI: HL-DT-ST DVD+/-RW GTA0N, A3B0, max UDMA/100 [ 1.279119] ata5.00: configured for UDMA/100 [ 1.284241] scsi 4:0:0:0: CD-ROM HL-DT-ST DVD+-RW GTA0N A3B0 PQ: 0 ANSI: 5 [ 1.313632] sr 4:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.313826] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.326636] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 1.326719] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 1.387153] usb 3-9.1: new high-speed USB device number 3 using xhci_hcd [ 1.474140] usb 3-9.1: New USB device found, idVendor=0624, idProduct=0249, bcdDevice= 0.00 [ 1.474321] usb 3-9.1: New USB device strings: Mfr=4, Product=5, SerialNumber=6 [ 1.474495] usb 3-9.1: Product: Keyboard/Mouse Function [ 1.474636] usb 3-9.1: Manufacturer: Avocent [ 1.474774] usb 3-9.1: SerialNumber: 20120917 [ 1.481557] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.0/0003:0624:0249.0001/input/input1 [ 1.533376] hid-generic 0003:0624:0249.0001: input,hidraw0: USB HID v1.00 Keyboard [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input0 [ 1.534465] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.1/0003:0624:0249.0002/input/input2 [ 1.534776] hid-generic 0003:0624:0249.0002: input,hidraw1: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input1 [ 1.535734] input: Avocent Keyboard/Mouse Function as /devices/pci0000:00/0000:00:14.0/usb3/3-9/3-9.1/3-9.1:1.2/0003:0624:0249.0003/input/input3 [ 1.536009] hid-generic 0003:0624:0249.0003: input,hidraw2: USB HID v1.00 Mouse [Avocent Keyboard/Mouse Function] on usb-0000:00:14.0-9.1/input2 [ 1.639446] ata6: SATA link down (SStatus 0 SControl 300) [ 1.640834] Freeing unused kernel image (initmem) memory: 2680K [ 1.640996] Write protecting the kernel read-only data: 24576k [ 1.654874] Freeing unused kernel image (rodata/data gap) memory: 2028K [ 1.853107] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.853256] Run /init as init process [ 1.853392] with arguments: [ 1.853393] /init [ 1.853394] placeholder [ 1.853395] with environment: [ 1.853395] HOME=/ [ 1.853396] TERM=linux [ 2.078767] tg3 0000:01:00.0 enx549f3505fd88: renamed from eth0 [ 2.080575] tg3 0000:01:00.1 enx549f3505fd8a: renamed from eth1 [ 2.874431] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 3.108376] EXT4-fs (dm-0): mounted filesystem 91d93f6d-2b78-47ff-8255-5deed2620791 ro with ordered data mode. Quota mode: none. [ 6.605803] EXT4-fs (dm-0): re-mounted 91d93f6d-2b78-47ff-8255-5deed2620791 r/w. Quota mode: none. [ 7.737030] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 7.757798] EXT4-fs (sda1): mounted filesystem 1c85306c-0391-4d54-af2f-6e84339460c8 r/w with ordered data mode. Quota mode: none. [ 7.825738] Adding 1949692k swap on /dev/mapper/godello1--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 9.308013] xenbr0: port 1(enx549f3505fd88) entered blocking state [ 9.308247] xenbr0: port 1(enx549f3505fd88) entered disabled state [ 9.308399] tg3 0000:01:00.0 enx549f3505fd88: entered allmulticast mode [ 9.308580] tg3 0000:01:00.0 enx549f3505fd88: entered promiscuous mode [ 12.898358] tg3 0000:01:00.0 enx549f3505fd88: Link is up at 1000 Mbps, full duplex [ 12.898571] tg3 0000:01:00.0 enx549f3505fd88: Flow control is off for TX and off for RX [ 12.898839] tg3 0000:01:00.0 enx549f3505fd88: EEE is disabled [ 12.899080] xenbr0: port 1(enx549f3505fd88) entered blocking state [ 12.899242] xenbr0: port 1(enx549f3505fd88) entered forwarding state