[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod1) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Jun 29 01:56:31 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414604K/524288K available (15360K kernel code, 2268K rwdata, 6084K rodata, 2048K init, 439K bss, 44148K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000537] Console: colour dummy device 80x30 [ 0.000556] printk: legacy console [hvc0] enabled [ 0.299206] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309604] CPU: Testing write buffer coherency: ok [ 0.314545] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.324099] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330531] pid_max: default: 32768 minimum: 301 [ 0.335299] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342579] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350999] /cpus/cpu@0 missing clock-frequency property [ 0.355782] /cpus/cpu@1 missing clock-frequency property [ 0.361200] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367903] xen:grant_table: Grant tables using version 1 layout [ 0.373031] Grant table initialized [ 0.376587] xen:events: Using FIFO-based ABI [ 0.380885] Xen: initializing cpu0 [ 0.384410] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392198] rcu: Hierarchical SRCU implementation. [ 0.395803] rcu: Max phase no-delay instances is 1000. [ 0.404040] EFI services will not be available. [ 0.407361] smp: Bringing up secondary CPUs ... [ 0.481594] Xen: initializing cpu1 [ 0.481756] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481780] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500755] smp: Brought up 1 node, 2 CPUs [ 0.504407] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510695] CPU: All CPU(s) started in SVC mode. [ 0.516600] devtmpfs: initialized [ 0.529012] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535561] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545236] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553136] pinctrl core: initialized pinctrl subsystem [ 0.559766] DMI not present or invalid. [ 0.563277] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569898] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579217] thermal_sys: Registered thermal governor 'step_wise' [ 0.579376] software IO TLB: area num 2. [ 0.588046] software IO TLB: only able to allocate 8 MB [ 0.595119] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600322] No ATAGs? [ 0.602626] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611343] Serial: AMBA PL011 UART driver [ 0.657969] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686458] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.710422] xen:balloon: Initialising balloon driver [ 0.716884] iommu: Default domain type: Translated [ 0.720296] iommu: DMA domain TLB invalidation policy: strict mode [ 0.729084] SCSI subsystem initialized [ 0.731621] libata version 3.00 loaded. [ 0.731855] usbcore: registered new interface driver usbfs [ 0.737086] usbcore: registered new interface driver hub [ 0.742424] usbcore: registered new device driver usb [ 0.749142] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.752738] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.758998] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.764058] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.768986] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.775027] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.780808] pps_core: LinuxPPS API ver. 1 registered [ 0.785198] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.794423] PTP clock support registered [ 0.798660] EDAC MC: Ver: 3.0.0 [ 0.801915] scmi_core: SCMI protocol bus registered [ 0.808615] vgaarb: loaded [ 0.811750] clocksource: Switched to clocksource arch_sys_counter [ 0.828772] NET: Registered PF_INET protocol family [ 0.832446] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.840317] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.848037] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.855816] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.863653] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.870928] TCP: Hash tables configured (established 4096 bind 4096) [ 0.877304] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.883871] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.890963] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.897128] RPC: Registered named UNIX socket transport module. [ 0.902604] RPC: Registered udp transport module. [ 0.907359] RPC: Registered tcp transport module. [ 0.912155] RPC: Registered tcp-with-tls transport module. [ 0.917707] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.924218] PCI: CLS 0 bytes, default 64 [ 0.929631] Initialise system trusted keyrings [ 0.932936] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.939462] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.945342] NFS: Registering the id_resolver key type [ 0.950265] Key type id_resolver registered [ 0.954506] Key type id_legacy registered [ 0.958610] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.965366] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.973081] Trying to unpack rootfs image as initramfs... [ 0.994515] Key type asymmetric registered [ 0.997255] Asymmetric key parser 'x509' registered [ 1.002322] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.009668] io scheduler mq-deadline registered [ 1.014288] io scheduler kyber registered [ 1.018399] io scheduler bfq registered [ 1.159495] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.165757] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.219949] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.226211] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.254601] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.260855] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.312085] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.318318] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.331045] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.344305] xen:xen_evtchn: Event-channel device installed [ 1.404422] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.415388] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.423660] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.432488] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.441633] SuperH (H)SCI(F) driver initialized [ 1.445849] STMicroelectronics ASC driver initialized [ 1.450679] STM32 USART driver initialized [ 1.456100] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.465574] random: crng init done [ 1.474746] brd: module loaded [ 1.481598] loop: module loaded [ 1.497051] Invalid max_queues (4), will use default max: 2. [ 1.517266] tun: Universal TUN/TAP device driver, 1.6 [ 1.521163] CAN device driver interface [ 1.526300] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.537726] xen_netfront: Initialising Xen virtual ethernet driver [ 1.542631] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.548226] usbcore: registered new interface driver pegasus [ 1.553951] usbcore: registered new interface driver asix [ 1.559400] usbcore: registered new interface driver ax88179_178a [ 1.565601] usbcore: registered new interface driver cdc_ether [ 1.571473] usbcore: registered new interface driver smsc75xx [ 1.577292] usbcore: registered new interface driver smsc95xx [ 1.583119] usbcore: registered new interface driver net1080 [ 1.588830] usbcore: registered new interface driver cdc_subset [ 1.593725] Freeing initrd memory: 11856K [ 1.594844] usbcore: registered new interface driver zaurus [ 1.604558] usbcore: registered new interface driver cdc_ncm [ 1.614055] usbcore: registered new interface driver usb-storage [ 1.624584] i2c_dev: i2c /dev entries driver [ 1.643080] device-mapper: uevent: version 1.0.3 [ 1.646503] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.656090] cpu cpu0: OPP table can't be empty [ 1.660834] failed to register cpuidle driver [ 1.664222] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.672586] sdhci: Secure Digital Host Controller Interface driver [ 1.677569] sdhci: Copyright(c) Pierre Ossman [ 1.685604] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.699772] ledtrig-cpu: registered to indicate activity on CPUs [ 1.705206] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.711884] usbcore: registered new interface driver usbhid [ 1.716551] usbhid: USB HID core driver [ 1.727420] NET: Registered PF_INET6 protocol family [ 1.731898] Segment Routing with IPv6 [ 1.734770] In-situ OAM (IOAM) with IPv6 [ 1.738818] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.745200] NET: Registered PF_PACKET protocol family [ 1.749868] can: controller area network core [ 1.754332] NET: Registered PF_CAN protocol family [ 1.759138] can: raw protocol [ 1.762188] can: broadcast manager protocol [ 1.766434] can: netlink gateway - max_hops=1 [ 1.771164] Key type dns_resolver registered [ 1.776896] ThumbEE CPU extension supported. [ 1.779793] Registering SWP/SWPB emulation handler [ 1.794105] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.802716] Loading compiled-in X.509 certificates [ 1.845076] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.848695] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.855311] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.863450] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 1.904096] s5m-rtc s5m-rtc: registered as rtc0 [ 1.912935] s5m-rtc s5m-rtc: setting system clock to 2024-06-29T03:56:10 UTC (1719633370) [ 1.924042] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 1.928640] s3c-i2c 12c90000.i2c: slave address 0x00 [ 1.933082] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 1.939829] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 1.945735] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 1.951978] clk: Not disabling unused clocks [ 1.955402] PM: genpd: Disabling unused power domains [ 1.963943] Freeing unused kernel image (initmem) memory: 2048K [ 1.970313] Run /init as init process [ 1.972647] with arguments: [ 1.972653] /init [ 1.972659] with environment: [ 1.972664] HOME=/ [ 1.972670] TERM=linux [ 3.196162] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.338261] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.374135] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.379900] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.385888] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.396673] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.402814] exynos-ohci 12120000.usb: USB Host Controller [ 3.407990] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.422620] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.438025] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.491978] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.526926] hub 2-0:1.0: USB hub found [ 3.530408] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.533865] Synopsys Designware Multimedia Card Interface Driver [ 3.537023] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.550422] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.558038] hub 2-0:1.0: 3 ports detected [ 3.594937] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.601020] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.607959] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.612439] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.619662] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.628558] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.635376] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.671957] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.676757] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.683181] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.688649] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.702062] mmc_host mmc0: card is polling. [ 3.712043] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.717432] hub 1-0:1.0: USB hub found [ 3.720316] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.731502] hub 1-0:1.0: 3 ports detected [ 3.734185] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.734200] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.746246] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.764382] scsi host0: ahci-dwc [ 3.766565] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 3.780362] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.791369] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.799962] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.924157] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.937822] mmc0: new DDR MMC card at address 0001 [ 3.944492] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 3.952143] mmcblk0: p1 p2 p3 p4 [ 3.956264] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 3.962195] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 3.968833] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.006210] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.015002] mmc1: new high speed SDHC card at address aaaa [ 4.027905] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.281858] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.289259] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.294643] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.308217] ata1.00: configured for UDMA/133 [ 4.312596] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.320718] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.326897] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.332476] sd 0:0:0:0: [sda] Write Protect is off [ 4.337032] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.337189] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.346400] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.373473] sda: sda1 sda2 < sda5 > [ 4.377035] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.493447] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.500816] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.505555] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.523915] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.533555] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.538440] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.543849] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.551515] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.584339] hub 3-0:1.0: USB hub found [ 4.586810] hub 3-0:1.0: 1 port detected [ 4.591520] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.605837] hub 4-0:1.0: USB hub found [ 4.608435] hub 4-0:1.0: 1 port detected [ 4.637062] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.810932] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.919612] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.027741] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.135836] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.244000] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.352305] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.460479] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.568580] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.676698] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.085488] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.193249] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.801626] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 10.279309] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 10.589404] EXT4-fs (dm-0): mounted filesystem c9175b97-2d81-48c4-aec7-45637bd975e9 ro with ordered data mode. Quota mode: disabled. [ 14.410501] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 14.410800] s5p-secss 10830000.sss: s5p-sss driver registered [ 14.574921] mc: Linux media interface: v0.10 [ 14.760213] videodev: Linux video capture interface: v2.00 [ 14.910636] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.015526] exynos-gsc 13e00000.gsc: Adding to iommu group 0 [ 15.021967] exynos-gsc 13e10000.gsc: Adding to iommu group 1 [ 15.029179] exynos-gsc 13e20000.gsc: Adding to iommu group 2 [ 15.037195] exynos-gsc 13e30000.gsc: Adding to iommu group 3 [ 15.067555] s5p-mfc 11000000.codec: Adding to iommu group 4 [ 15.105893] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.114295] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.164078] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 15.180675] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.190122] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.203290] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.213247] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 15.220649] blk_print_req_error: 6 callbacks suppressed [ 15.220665] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.247034] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 15.254832] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 15.264978] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 15.283017] usb3503 usb-hub: switched to HUB mode [ 15.286386] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.334347] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.445506] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.553657] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.641841] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 15.661818] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.770609] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.844181] hub 1-3:1.0: USB hub found [ 15.850286] hub 1-3:1.0: 3 ports detected [ 15.879820] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.898295] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.905960] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.914741] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.925491] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.934270] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.943018] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.988018] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.181784] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.334463] hub 1-3.2:1.0: USB hub found [ 16.337479] hub 1-3.2:1.0: 4 ports detected [ 16.374653] usbcore: registered new device driver onboard-usb-dev [ 16.396854] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 16.504629] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 16.513095] hub 1-3.2:1.0: USB hub found [ 16.516636] hub 1-3.2:1.0: 4 ports detected [ 16.528934] hub 1-3.2:1.0: USB hub found [ 16.532245] hub 1-3.2:1.0: 4 ports detected [ 16.851807] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.005138] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.113138] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 17.663640] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 17.678010] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 17.687908] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 7a:4d:e2:42:99:ae [ 18.349193] EXT4-fs (dm-0): re-mounted c9175b97-2d81-48c4-aec7-45637bd975e9 r/w. Quota mode: disabled. [ 20.306868] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.355804] EXT4-fs (sda1): mounted filesystem 04f2443c-f5e8-4882-b2e8-fbee734ce901 r/w with ordered data mode. Quota mode: disabled. [ 20.451016] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 22.237618] xenbr0: port 1(eth0) entered blocking state [ 22.241483] xenbr0: port 1(eth0) entered disabled state [ 22.246823] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 22.252691] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 22.263552] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.513059] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 24.519075] xenbr0: port 1(eth0) entered blocking state [ 24.524309] xenbr0: port 1(eth0) entered forwarding state [ 26.893606] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed