[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-21-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.90-1 (2024-05-03) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44756 r8192 d20780 u73728 [ 0.000000] pcpu-alloc: s44756 r8192 d20780 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015524K/2097152K available (12288K kernel code, 1714K rwdata, 3748K rodata, 2048K init, 382K bss, 65244K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39974 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002634] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002649] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002664] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002676] Ignoring duplicate/late registration of read_current_timer delay [ 0.003043] Console: colour dummy device 80x30 [ 0.003084] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003098] CPU: Testing write buffer coherency: ok [ 0.003140] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003147] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003154] pid_max: default: 32768 minimum: 301 [ 0.003514] LSM: Security Framework initializing [ 0.003586] landlock: Up and running. [ 0.003591] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003776] AppArmor: AppArmor initialized [ 0.003788] TOMOYO Linux initialized [ 0.003832] LSM support for eBPF active [ 0.004076] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004090] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005502] /cpus/cpu@0 missing clock-frequency property [ 0.005531] /cpus/cpu@1 missing clock-frequency property [ 0.005545] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006506] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006513] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006618] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006624] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006765] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007927] rcu: Hierarchical SRCU implementation. [ 0.007933] rcu: Max phase no-delay instances is 1000. [ 0.010067] EFI services will not be available. [ 0.010414] smp: Bringing up secondary CPUs ... [ 0.011163] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011175] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011309] smp: Brought up 1 node, 2 CPUs [ 0.011317] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011325] CPU: All CPU(s) started in HYP mode. [ 0.011329] CPU: Virtualization extensions available. [ 0.012196] devtmpfs: initialized [ 0.023730] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023993] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.024018] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024560] pinctrl core: initialized pinctrl subsystem [ 0.025307] DMI not present or invalid. [ 0.025983] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027546] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.029128] audit: initializing netlink subsys (disabled) [ 0.029332] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.030541] thermal_sys: Registered thermal governor 'fair_share' [ 0.030548] thermal_sys: Registered thermal governor 'bang_bang' [ 0.030553] thermal_sys: Registered thermal governor 'step_wise' [ 0.030557] thermal_sys: Registered thermal governor 'user_space' [ 0.030562] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030767] No ATAGs? [ 0.030832] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030841] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031941] Serial: AMBA PL011 UART driver [ 0.085312] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.092591] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.095875] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.095884] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.102784] iommu: Default domain type: Translated [ 0.102793] iommu: DMA domain TLB invalidation policy: strict mode [ 0.103779] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.104315] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.104326] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.104968] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.104999] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.105204] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.105564] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.105574] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.105962] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.106256] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.106265] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.106567] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.106683] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.106692] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.106879] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.107093] pps_core: LinuxPPS API ver. 1 registered [ 0.107098] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.107115] PTP clock support registered [ 0.108642] NetLabel: Initializing [ 0.108647] NetLabel: domain hash size = 128 [ 0.108653] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.108705] NetLabel: unlabeled traffic allowed by default [ 0.108881] vgaarb: loaded [ 0.109435] clocksource: Switched to clocksource mct-frc [ 0.110014] VFS: Disk quotas dquot_6.6.0 [ 0.110100] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.110856] AppArmor: AppArmor Filesystem Enabled [ 0.121088] NET: Registered PF_INET protocol family [ 0.121288] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.122785] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.122887] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.122912] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.123012] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.123244] TCP: Hash tables configured (established 8192 bind 8192) [ 0.123474] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.123567] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123608] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.123822] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.123859] NET: Registered PF_XDP protocol family [ 0.123871] PCI: CLS 0 bytes, default 64 [ 0.124359] Trying to unpack rootfs image as initramfs... [ 0.124730] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.130104] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.195532] Initialise system trusted keyrings [ 0.195608] Key type blacklist registered [ 0.196844] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.205089] zbud: loaded [ 0.206402] integrity: Platform Keyring initialized [ 0.206446] integrity: Machine keyring initialized [ 0.206456] Key type asymmetric registered [ 0.206464] Asymmetric key parser 'x509' registered [ 1.430780] Freeing initrd memory: 25116K [ 1.452976] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.453244] bounce: pool size: 64 pages [ 1.453466] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.453660] io scheduler mq-deadline registered [ 1.458804] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.479963] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.479975] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.482410] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.482420] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.483246] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.483255] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.484097] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.484105] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.486470] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.489254] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.492056] Serial: AMBA driver [ 1.492286] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.492769] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.493259] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.573897] printk: console [ttySAC2] enabled [ 2.578722] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.589371] STM32 USART driver initialized [ 2.603843] mousedev: PS/2 mouse device common for all mice [ 2.635085] s5m-rtc s5m-rtc: registered as rtc0 [ 2.643713] s5m-rtc s5m-rtc: setting system clock to 2024-06-29T11:07:34 UTC (1719659254) [ 2.653607] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.661086] ledtrig-cpu: registered to indicate activity on CPUs [ 2.669075] NET: Registered PF_INET6 protocol family [ 2.693258] Segment Routing with IPv6 [ 2.695525] In-situ OAM (IOAM) with IPv6 [ 2.699458] mip6: Mobile IPv6 [ 2.702332] NET: Registered PF_PACKET protocol family [ 2.707483] mpls_gso: MPLS GSO support [ 2.711523] ThumbEE CPU extension supported. [ 2.715358] Registering SWP/SWPB emulation handler [ 2.720596] registered taskstats version 1 [ 2.724220] Loading compiled-in X.509 certificates [ 3.181006] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.188345] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.199426] zswap: loaded using pool lzo/zbud [ 3.203339] Key type .fscrypt registered [ 3.206678] Key type fscrypt-provisioning registered [ 3.231092] Key type encrypted registered [ 3.233688] AppArmor: AppArmor sha1 policy hashing enabled [ 3.239178] ima: No TPM chip found, activating TPM-bypass! [ 3.244620] ima: Allocated hash algorithm: sha256 [ 3.249306] ima: No architecture policies found [ 3.253888] evm: Initialising EVM extended attributes: [ 3.258911] evm: security.selinux [ 3.262211] evm: security.SMACK64 (disabled) [ 3.266456] evm: security.SMACK64EXEC (disabled) [ 3.271058] evm: security.SMACK64TRANSMUTE (disabled) [ 3.276093] evm: security.SMACK64MMAP (disabled) [ 3.280692] evm: security.apparmor [ 3.284076] evm: security.ima [ 3.287026] evm: security.capability [ 3.290592] evm: HMAC attrs: 0x1 [ 3.871725] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.877717] clk: Disabling unused clocks [ 3.890624] Freeing unused kernel image (initmem) memory: 2048K [ 3.895500] Checked W+X mappings: passed, no W+X pages found [ 3.900745] Run /init as init process [ 3.904378] with arguments: [ 3.904386] /init [ 3.904392] with environment: [ 3.904397] HOME=/ [ 3.904403] TERM=linux [ 4.830498] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.863575] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.863791] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.883413] usbcore: registered new interface driver usbfs [ 4.889043] usbcore: registered new interface driver hub [ 4.894052] usbcore: registered new device driver usb [ 4.909007] Synopsys Designware Multimedia Card Interface Driver [ 4.919499] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 4.929011] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.934856] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.935040] exynos-ehci 12110000.usb: EHCI Host Controller [ 4.949374] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 4.965613] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.970617] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.976179] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 4.985731] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.991893] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.997801] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 5.003597] mmc_host mmc0: card is polling. [ 5.007664] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.020161] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.031860] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.040809] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.047662] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.048069] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.054844] usb usb1: Product: EHCI Host Controller [ 5.064731] usb usb1: Manufacturer: Linux 6.1.0-21-armmp-lpae ehci_hcd [ 5.071238] usb usb1: SerialNumber: 12110000.usb [ 5.080776] hub 1-0:1.0: USB hub found [ 5.097484] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.106143] hub 1-0:1.0: 3 ports detected [ 5.125722] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 5.144642] exynos-ohci 12120000.usb: USB Host Controller [ 5.155894] SCSI subsystem initialized [ 5.169654] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.200550] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.203893] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.216803] mmc1: new high speed SDHC card at address aaaa [ 5.222593] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.229493] libata version 3.00 loaded. [ 5.235422] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.239920] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.240162] mmc0: new DDR MMC card at address 0001 [ 5.258106] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.265745] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.266719] mmcblk0: p1 p2 p3 p4 [ 5.272581] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.272591] usb usb2: Product: USB Host Controller [ 5.278219] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.283070] usb usb2: Manufacturer: Linux 6.1.0-21-armmp-lpae ohci_hcd [ 5.291711] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.292789] usb usb2: SerialNumber: 12120000.usb [ 5.302522] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.332233] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.352904] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.381826] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.387458] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.396281] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.442317] hub 2-0:1.0: USB hub found [ 5.452333] hub 2-0:1.0: 3 ports detected [ 5.457410] scsi host0: ahci-dwc [ 5.459714] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.664386] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.737671] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.846114] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.945504] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.951118] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.954116] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.956923] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.973704] ata1.00: configured for UDMA/133 [ 5.977417] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 6.029384] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.033460] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 6.041649] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.050564] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.056721] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.061906] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.069554] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.069588] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.076280] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.093572] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.100782] usb usb3: Product: xHCI Host Controller [ 6.105661] usb usb3: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.112155] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.119118] hub 3-0:1.0: USB hub found [ 6.121582] hub 3-0:1.0: 1 port detected [ 6.126628] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.133663] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.141664] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.148923] usb usb4: Product: xHCI Host Controller [ 6.153722] usb usb4: Manufacturer: Linux 6.1.0-21-armmp-lpae xhci-hcd [ 6.160229] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.166680] hub 4-0:1.0: USB hub found [ 6.168997] hub 4-0:1.0: 1 port detected [ 6.179727] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.185833] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.194293] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.205557] sd 0:0:0:0: [sda] Write Protect is off [ 6.208910] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.209020] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.221622] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.239347] sda: sda1 sda2 < sda5 > [ 6.242178] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.302275] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.410246] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.518227] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.626217] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 7.034772] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.142376] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.325457] random: crng init done [ 7.442592] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.453479] device-mapper: uevent: version 1.0.3 [ 7.461527] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.750510] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 11.234690] PM: Image not found (code -22) [ 11.844371] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.035134] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.342216] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.740925] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.770028] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.910782] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.938576] panfrost 11800000.gpu: clock rate = 533000000 [ 16.033524] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 16.039883] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 16.047979] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 16.059726] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 16.095598] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.166638] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.196473] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 16.203489] usb3503 usb-hub: switched to HUB mode [ 16.207211] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.275155] blk_print_req_error: 6 callbacks suppressed [ 16.275166] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.388688] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.497024] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.528998] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.605415] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.710186] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.717118] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.724268] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.735436] hub 1-3:1.0: USB hub found [ 16.745793] hub 1-3:1.0: 3 ports detected [ 16.833653] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.833919] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.941770] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.049867] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.058231] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.188221] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 17.195472] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 17.202614] usb 1-3.2: Product: USB2.0 Hub [ 17.210080] hub 1-3.2:1.0: USB hub found [ 17.214301] hub 1-3.2:1.0: 4 ports detected [ 17.459583] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.513678] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.567726] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.636449] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.643846] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.651277] usb 1-3.2.4: Product: AX88772 [ 17.655270] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.660565] usb 1-3.2.4: SerialNumber: 000001 [ 18.114532] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.177549] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 18.824052] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.839472] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.853546] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 42:77:b9:ca:df:15 [ 18.868170] usbcore: registered new interface driver asix [ 19.639265] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.819237] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.867996] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 22.076004] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 23.198045] audit: type=1400 audit(1719659274.856:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=880 comm="apparmor_parser" [ 23.214354] audit: type=1400 audit(1719659274.864:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=879 comm="apparmor_parser" [ 23.233817] audit: type=1400 audit(1719659274.876:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=880 comm="apparmor_parser" [ 23.618725] audit: type=1400 audit(1719659275.276:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=903 comm="apparmor_parser" [ 23.632792] audit: type=1400 audit(1719659275.276:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=903 comm="apparmor_parser" [ 23.647224] audit: type=1400 audit(1719659275.280:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=903 comm="apparmor_parser" [ 23.833714] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.001700] audit: type=1400 audit(1719659275.660:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=902 comm="apparmor_parser" [ 24.021662] audit: type=1400 audit(1719659275.660:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=902 comm="apparmor_parser" [ 24.037523] audit: type=1400 audit(1719659275.664:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=902 comm="apparmor_parser" [ 24.055099] audit: type=1400 audit(1719659275.672:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=902 comm="apparmor_parser" [ 25.991487] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.997554] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.897378] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.913203] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.921226] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.927767] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.936839] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.945247] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.951760] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.960362] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.966046] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.975493] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1