[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod0) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Jun 30 01:19:39 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414600K/524288K available (15360K kernel code, 2268K rwdata, 6084K rodata, 2048K init, 439K bss, 44152K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000013] Switching to timer-based delay loop, resolution 41ns [ 0.000511] Console: colour dummy device 80x30 [ 0.000530] printk: legacy console [hvc0] enabled [ 0.299179] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309577] CPU: Testing write buffer coherency: ok [ 0.314520] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.324073] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330486] pid_max: default: 32768 minimum: 301 [ 0.335272] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342553] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350981] /cpus/cpu@0 missing clock-frequency property [ 0.355756] /cpus/cpu@1 missing clock-frequency property [ 0.361173] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367873] xen:grant_table: Grant tables using version 1 layout [ 0.373007] Grant table initialized [ 0.376562] xen:events: Using FIFO-based ABI [ 0.380860] Xen: initializing cpu0 [ 0.384384] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392173] rcu: Hierarchical SRCU implementation. [ 0.395778] rcu: Max phase no-delay instances is 1000. [ 0.404013] EFI services will not be available. [ 0.407335] smp: Bringing up secondary CPUs ... [ 0.481568] Xen: initializing cpu1 [ 0.481728] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481752] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500730] smp: Brought up 1 node, 2 CPUs [ 0.504381] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510669] CPU: All CPU(s) started in SVC mode. [ 0.516603] devtmpfs: initialized [ 0.528930] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535485] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545158] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553080] pinctrl core: initialized pinctrl subsystem [ 0.559676] DMI not present or invalid. [ 0.563181] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569797] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579132] thermal_sys: Registered thermal governor 'step_wise' [ 0.579289] software IO TLB: area num 2. [ 0.587962] software IO TLB: only able to allocate 8 MB [ 0.595033] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600237] No ATAGs? [ 0.602540] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611242] Serial: AMBA PL011 UART driver [ 0.657873] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686349] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.710270] xen:balloon: Initialising balloon driver [ 0.716732] iommu: Default domain type: Translated [ 0.720149] iommu: DMA domain TLB invalidation policy: strict mode [ 0.728935] SCSI subsystem initialized [ 0.731473] libata version 3.00 loaded. [ 0.731704] usbcore: registered new interface driver usbfs [ 0.736937] usbcore: registered new interface driver hub [ 0.742277] usbcore: registered new device driver usb [ 0.748999] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.752589] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.758848] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.763910] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.768840] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.774880] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.780654] pps_core: LinuxPPS API ver. 1 registered [ 0.785048] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.794275] PTP clock support registered [ 0.798514] EDAC MC: Ver: 3.0.0 [ 0.801770] scmi_core: SCMI protocol bus registered [ 0.808458] vgaarb: loaded [ 0.811602] clocksource: Switched to clocksource arch_sys_counter [ 0.828786] NET: Registered PF_INET protocol family [ 0.832465] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.840334] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.848051] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.855834] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.863669] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.870944] TCP: Hash tables configured (established 4096 bind 4096) [ 0.877318] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.883888] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.890982] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.897150] RPC: Registered named UNIX socket transport module. [ 0.902622] RPC: Registered udp transport module. [ 0.907376] RPC: Registered tcp transport module. [ 0.912172] RPC: Registered tcp-with-tls transport module. [ 0.917724] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.924237] PCI: CLS 0 bytes, default 64 [ 0.929637] Initialise system trusted keyrings [ 0.932955] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.939478] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.945358] NFS: Registering the id_resolver key type [ 0.950284] Key type id_resolver registered [ 0.954524] Key type id_legacy registered [ 0.958627] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.965383] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.973098] Trying to unpack rootfs image as initramfs... [ 0.994385] Key type asymmetric registered [ 0.997126] Asymmetric key parser 'x509' registered [ 1.002187] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.009539] io scheduler mq-deadline registered [ 1.014160] io scheduler kyber registered [ 1.018270] io scheduler bfq registered [ 1.159689] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.165936] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.205818] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.212052] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.254575] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.260790] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.311812] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.318048] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.330814] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.405089] xen:xen_evtchn: Event-channel device installed [ 1.435629] Freeing initrd memory: 11860K [ 1.485539] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.496482] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.504663] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.513565] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.522547] SuperH (H)SCI(F) driver initialized [ 1.526865] STMicroelectronics ASC driver initialized [ 1.531777] STM32 USART driver initialized [ 1.537158] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.546078] random: crng init done [ 1.556643] brd: module loaded [ 1.562609] loop: module loaded [ 1.578085] Invalid max_queues (4), will use default max: 2. [ 1.596700] tun: Universal TUN/TAP device driver, 1.6 [ 1.600563] CAN device driver interface [ 1.605704] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.616852] xen_netfront: Initialising Xen virtual ethernet driver [ 1.621726] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.627323] usbcore: registered new interface driver pegasus [ 1.633070] usbcore: registered new interface driver asix [ 1.638541] usbcore: registered new interface driver ax88179_178a [ 1.644691] usbcore: registered new interface driver cdc_ether [ 1.650584] usbcore: registered new interface driver smsc75xx [ 1.656409] usbcore: registered new interface driver smsc95xx [ 1.662225] usbcore: registered new interface driver net1080 [ 1.667966] usbcore: registered new interface driver cdc_subset [ 1.673942] usbcore: registered new interface driver zaurus [ 1.679582] usbcore: registered new interface driver cdc_ncm [ 1.688991] usbcore: registered new interface driver usb-storage [ 1.699497] i2c_dev: i2c /dev entries driver [ 1.717794] device-mapper: uevent: version 1.0.3 [ 1.721219] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.730805] cpu cpu0: OPP table can't be empty [ 1.735545] failed to register cpuidle driver [ 1.738922] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.747253] sdhci: Secure Digital Host Controller Interface driver [ 1.752307] sdhci: Copyright(c) Pierre Ossman [ 1.760324] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.768251] ledtrig-cpu: registered to indicate activity on CPUs [ 1.773679] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.780315] usbcore: registered new interface driver usbhid [ 1.785039] usbhid: USB HID core driver [ 1.795926] NET: Registered PF_INET6 protocol family [ 1.801373] Segment Routing with IPv6 [ 1.803717] In-situ OAM (IOAM) with IPv6 [ 1.807711] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.814125] NET: Registered PF_PACKET protocol family [ 1.818796] can: controller area network core [ 1.823263] NET: Registered PF_CAN protocol family [ 1.828069] can: raw protocol [ 1.831090] can: broadcast manager protocol [ 1.835360] can: netlink gateway - max_hops=1 [ 1.840096] Key type dns_resolver registered [ 1.844772] ThumbEE CPU extension supported. [ 1.848451] Registering SWP/SWPB emulation handler [ 1.862885] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.869758] Loading compiled-in X.509 certificates [ 1.913639] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.917238] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.923926] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.932044] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 1.973557] s5m-rtc s5m-rtc: registered as rtc0 [ 1.982424] s5m-rtc s5m-rtc: setting system clock to 2024-06-30T02:31:43 UTC (1719714703) [ 1.993451] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 1.998063] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.002491] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.009177] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.015111] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.021280] clk: Not disabling unused clocks [ 2.024860] PM: genpd: Disabling unused power domains [ 2.033397] Freeing unused kernel image (initmem) memory: 2048K [ 2.039680] Run /init as init process [ 2.042001] with arguments: [ 2.042008] /init [ 2.042014] with environment: [ 2.042019] HOME=/ [ 2.042024] TERM=linux [ 3.274736] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.406723] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.452136] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.457740] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.463369] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.487879] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.501627] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.510528] phy phy-12130000.phy.6: phy_power_on was called before phy_init [ 3.516146] exynos-ohci 12120000.usb: USB Host Controller [ 3.548972] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.561973] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.575562] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.591726] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.607117] Synopsys Designware Multimedia Card Interface Driver [ 3.616890] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.623170] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.668447] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.708666] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.718263] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.724009] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.724436] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.732834] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.746640] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.756924] hub 1-0:1.0: USB hub found [ 3.761364] hub 1-0:1.0: 3 ports detected [ 3.776835] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.782391] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.792417] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.805480] mmc_host mmc0: card is polling. [ 3.824028] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.835075] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.839342] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.850715] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.854315] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.854332] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.854427] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 128,32 bit host data width,128 deep fifo [ 3.877554] hub 2-0:1.0: USB hub found [ 3.887842] hub 2-0:1.0: 3 ports detected [ 3.911288] scsi host0: ahci-dwc [ 3.913452] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 127 lpm-pol 0 [ 3.931862] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.979352] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.992952] mmc0: new DDR MMC card at address 0001 [ 4.042661] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.065702] mmcblk0: p1 p2 p3 p4 [ 4.073021] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.085719] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.102083] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.155649] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.172436] mmc1: new high speed SDHC card at address aaaa [ 4.181319] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.431774] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.437510] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.443443] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.450990] ata1.00: configured for UDMA/133 [ 4.454679] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.463809] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.470009] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.475422] sd 0:0:0:0: [sda] Write Protect is off [ 4.480165] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.480241] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.489415] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.511693] sda: sda1 sda2 < sda5 > [ 4.514678] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.548326] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.558237] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.562433] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.614431] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.622741] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.628726] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.634200] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.641897] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.649973] hub 3-0:1.0: USB hub found [ 4.652439] hub 3-0:1.0: 1 port detected [ 4.657240] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.674094] hub 4-0:1.0: USB hub found [ 4.678862] hub 4-0:1.0: 1 port detected [ 4.790845] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.960426] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.069137] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.177399] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.285529] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.393709] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.501876] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.609958] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.718077] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 5.826184] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 6.234964] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.342719] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 6.951084] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 10.450339] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 10.674060] EXT4-fs (dm-0): mounted filesystem 739fdded-abbe-467b-a760-83d2bcd44eb4 ro with ordered data mode. Quota mode: disabled. [ 14.506737] s5p-secss 10830000.sss: s5p-sss driver registered [ 14.512023] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 14.592976] mc: Linux media interface: v0.10 [ 14.700292] videodev: Linux video capture interface: v2.00 [ 14.956921] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 14.965007] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 14.978686] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 15.005882] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.013886] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.022349] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.034666] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 15.040201] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 15.109459] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 15.116207] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 15.122787] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 15.129072] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 15.137654] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.231828] usb3503 usb-hub: switched to HUB mode [ 15.235171] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.247249] blk_print_req_error: 6 callbacks suppressed [ 15.247432] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.363326] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.475570] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.584677] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.593947] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 15.618896] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 15.639282] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 15.693304] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.706666] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 15.802902] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 15.834342] hub 1-3:1.0: USB hub found [ 15.837052] hub 1-3:1.0: 3 ports detected [ 15.914363] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.022659] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 16.040192] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.047937] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.056593] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.072090] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 16.079795] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 16.088539] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 16.201659] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.354323] hub 1-3.2:1.0: USB hub found [ 16.357264] hub 1-3.2:1.0: 4 ports detected [ 16.417813] usbcore: registered new device driver onboard-usb-dev [ 16.431490] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 16.539253] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 16.554490] hub 1-3.2:1.0: USB hub found [ 16.557440] hub 1-3.2:1.0: 4 ports detected [ 16.570138] hub 1-3.2:1.0: USB hub found [ 16.573143] hub 1-3.2:1.0: 4 ports detected [ 16.891634] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.045391] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.153394] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 17.703513] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 17.717759] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 17.727613] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 2a:e1:bb:7a:03:ba [ 18.367177] EXT4-fs (dm-0): re-mounted 739fdded-abbe-467b-a760-83d2bcd44eb4 r/w. Quota mode: disabled. [ 20.380587] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.429394] EXT4-fs (sda1): mounted filesystem b5c40912-d14c-4628-b1d9-d83246d6d2b4 r/w with ordered data mode. Quota mode: disabled. [ 20.535783] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 22.297163] xenbr0: port 1(eth0) entered blocking state [ 22.301029] xenbr0: port 1(eth0) entered disabled state [ 22.306396] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 22.312271] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 22.323301] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.500057] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 24.506101] xenbr0: port 1(eth0) entered blocking state [ 24.511295] xenbr0: port 1(eth0) entered forwarding state [ 26.893450] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed