[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.10.0-rc5+ (osstest@himrod2) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Jun 30 15:46:07 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.19 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41428 r8192 d24108 u73728 [ 0.000000] pcpu-alloc: s41428 r8192 d24108 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 414600K/524288K available (15360K kernel code, 2268K rwdata, 6084K rodata, 2048K init, 439K bss, 44152K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000014] Switching to timer-based delay loop, resolution 41ns [ 0.000553] Console: colour dummy device 80x30 [ 0.000571] printk: legacy console [hvc0] enabled [ 0.299042] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.309440] CPU: Testing write buffer coherency: ok [ 0.314382] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.323936] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.330349] pid_max: default: 32768 minimum: 301 [ 0.335135] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.342416] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.350846] /cpus/cpu@0 missing clock-frequency property [ 0.355619] /cpus/cpu@1 missing clock-frequency property [ 0.361036] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.367734] xen:grant_table: Grant tables using version 1 layout [ 0.372869] Grant table initialized [ 0.376421] xen:events: Using FIFO-based ABI [ 0.380721] Xen: initializing cpu0 [ 0.384247] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.392036] rcu: Hierarchical SRCU implementation. [ 0.395640] rcu: Max phase no-delay instances is 1000. [ 0.403871] EFI services will not be available. [ 0.407187] smp: Bringing up secondary CPUs ... [ 0.481449] Xen: initializing cpu1 [ 0.481608] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.481632] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.500591] smp: Brought up 1 node, 2 CPUs [ 0.504262] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.510549] CPU: All CPU(s) started in SVC mode. [ 0.516453] devtmpfs: initialized [ 0.528987] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.535541] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.545211] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.553116] pinctrl core: initialized pinctrl subsystem [ 0.559728] DMI not present or invalid. [ 0.563239] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.569855] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.579176] thermal_sys: Registered thermal governor 'step_wise' [ 0.579334] software IO TLB: area num 2. [ 0.588008] software IO TLB: only able to allocate 8 MB [ 0.595077] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.600280] No ATAGs? [ 0.602584] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.611285] Serial: AMBA PL011 UART driver [ 0.657936] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.686371] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.710346] xen:balloon: Initialising balloon driver [ 0.716793] iommu: Default domain type: Translated [ 0.720202] iommu: DMA domain TLB invalidation policy: strict mode [ 0.728994] SCSI subsystem initialized [ 0.731530] libata version 3.00 loaded. [ 0.731759] usbcore: registered new interface driver usbfs [ 0.736990] usbcore: registered new interface driver hub [ 0.742331] usbcore: registered new device driver usb [ 0.749051] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.752643] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.758906] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.763964] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.768894] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.774934] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.780711] pps_core: LinuxPPS API ver. 1 registered [ 0.785103] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.794329] PTP clock support registered [ 0.798564] EDAC MC: Ver: 3.0.0 [ 0.801822] scmi_core: SCMI protocol bus registered [ 0.808517] vgaarb: loaded [ 0.811696] clocksource: Switched to clocksource arch_sys_counter [ 0.828632] NET: Registered PF_INET protocol family [ 0.832310] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.840177] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.847896] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.855680] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.863515] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.870790] TCP: Hash tables configured (established 4096 bind 4096) [ 0.877164] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.883734] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.890827] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.896993] RPC: Registered named UNIX socket transport module. [ 0.902467] RPC: Registered udp transport module. [ 0.907221] RPC: Registered tcp transport module. [ 0.912017] RPC: Registered tcp-with-tls transport module. [ 0.917569] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.924082] PCI: CLS 0 bytes, default 64 [ 0.929486] Initialise system trusted keyrings [ 0.932796] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.939323] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.945204] NFS: Registering the id_resolver key type [ 0.950137] Key type id_resolver registered [ 0.954368] Key type id_legacy registered [ 0.958474] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.965229] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.972940] Trying to unpack rootfs image as initramfs... [ 0.994470] Key type asymmetric registered [ 0.997206] Asymmetric key parser 'x509' registered [ 1.002272] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.009618] io scheduler mq-deadline registered [ 1.014240] io scheduler kyber registered [ 1.018347] io scheduler bfq registered [ 1.159636] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.165886] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.205753] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.211992] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.254514] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.260723] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.311740] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.317974] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.330736] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.404986] xen:xen_evtchn: Event-channel device installed [ 1.435350] Freeing initrd memory: 11860K [ 1.485480] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.496437] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.504624] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.513512] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.522508] SuperH (H)SCI(F) driver initialized [ 1.526822] STMicroelectronics ASC driver initialized [ 1.531763] STM32 USART driver initialized [ 1.537084] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.546026] random: crng init done [ 1.556479] brd: module loaded [ 1.562478] loop: module loaded [ 1.577948] Invalid max_queues (4), will use default max: 2. [ 1.596518] tun: Universal TUN/TAP device driver, 1.6 [ 1.600384] CAN device driver interface [ 1.605524] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.616676] xen_netfront: Initialising Xen virtual ethernet driver [ 1.621525] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.627154] usbcore: registered new interface driver pegasus [ 1.632886] usbcore: registered new interface driver asix [ 1.638361] usbcore: registered new interface driver ax88179_178a [ 1.644516] usbcore: registered new interface driver cdc_ether [ 1.650403] usbcore: registered new interface driver smsc75xx [ 1.656229] usbcore: registered new interface driver smsc95xx [ 1.662044] usbcore: registered new interface driver net1080 [ 1.667763] usbcore: registered new interface driver cdc_subset [ 1.673762] usbcore: registered new interface driver zaurus [ 1.679401] usbcore: registered new interface driver cdc_ncm [ 1.688799] usbcore: registered new interface driver usb-storage [ 1.699284] i2c_dev: i2c /dev entries driver [ 1.717596] device-mapper: uevent: version 1.0.3 [ 1.721023] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.730603] cpu cpu0: OPP table can't be empty [ 1.735350] failed to register cpuidle driver [ 1.738724] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.747049] sdhci: Secure Digital Host Controller Interface driver [ 1.752105] sdhci: Copyright(c) Pierre Ossman [ 1.760126] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.768113] ledtrig-cpu: registered to indicate activity on CPUs [ 1.773547] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.780183] usbcore: registered new interface driver usbhid [ 1.784903] usbhid: USB HID core driver [ 1.795785] NET: Registered PF_INET6 protocol family [ 1.800247] Segment Routing with IPv6 [ 1.803174] In-situ OAM (IOAM) with IPv6 [ 1.807167] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.813581] NET: Registered PF_PACKET protocol family [ 1.818252] can: controller area network core [ 1.822722] NET: Registered PF_CAN protocol family [ 1.827504] can: raw protocol [ 1.830545] can: broadcast manager protocol [ 1.834816] can: netlink gateway - max_hops=1 [ 1.839561] Key type dns_resolver registered [ 1.844239] ThumbEE CPU extension supported. [ 1.847929] Registering SWP/SWPB emulation handler [ 1.862367] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 1.869262] Loading compiled-in X.509 certificates [ 1.912324] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.915921] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.922676] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.930681] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 1.979567] s5m-rtc s5m-rtc: registered as rtc0 [ 1.988464] s5m-rtc s5m-rtc: setting system clock to 2000-01-02T00:00:22 UTC (946771222) [ 1.999430] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.004149] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.008406] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.015242] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.021144] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.027254] clk: Not disabling unused clocks [ 2.030816] PM: genpd: Disabling unused power domains [ 2.039359] Freeing unused kernel image (initmem) memory: 2048K [ 2.045658] Run /init as init process [ 2.047938] with arguments: [ 2.047945] /init [ 2.047952] with environment: [ 2.047957] HOME=/ [ 2.047963] TERM=linux [ 3.318199] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.419834] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.546109] Synopsys Designware Multimedia Card Interface Driver [ 3.550199] phy phy-12130000.phy.7: phy_power_on was called before phy_init [ 3.557836] exynos-ohci 12120000.usb: USB Host Controller [ 3.557996] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.563293] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 3.571826] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.580756] phy phy-12130000.phy.7: phy_power_on was called before phy_init [ 3.595254] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.600785] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 3.617706] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.623955] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.631273] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.672807] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.674915] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.690174] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.697819] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.702011] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.709929] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.719078] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.725331] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.735694] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.741014] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.741970] VDD_ALIVE_1.0V: Bringing 1000000uV into 1100000-1100000uV [ 3.746588] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.762884] mmc_host mmc0: card is polling. [ 3.767866] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.773345] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.778832] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.779511] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.802003] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.810095] scsi host0: ahci-dwc [ 3.812947] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 3.813777] hub 1-0:1.0: USB hub found [ 3.832555] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.837449] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.849379] hub 1-0:1.0: 3 ports detected [ 3.859696] hub 2-0:1.0: USB hub found [ 3.870149] hub 2-0:1.0: 3 ports detected [ 3.884726] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.895922] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.956697] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 3.967276] mmc0: new DDR MMC card at address 0001 [ 3.972027] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 3.980819] mmcblk0: p1 p2 p3 p4 [ 3.983749] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 3.992025] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 3.997024] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.117183] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.126018] mmc1: new high speed SDHC card at address aaaa [ 4.133214] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.321774] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.328212] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.333574] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.341973] ata1.00: configured for UDMA/133 [ 4.345209] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.357931] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.364090] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.370881] sd 0:0:0:0: [sda] Write Protect is off [ 4.374324] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.375117] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.384015] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.409921] sda: sda1 sda2 < sda5 > [ 4.412728] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.513673] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.522753] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.526905] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.556388] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002000010 [ 4.573714] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.578651] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.583953] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.591682] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.616911] hub 3-0:1.0: USB hub found [ 4.622975] hub 3-0:1.0: 1 port detected [ 4.631322] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.648895] hub 4-0:1.0: USB hub found [ 4.653029] hub 4-0:1.0: 1 port detected [ 9.713936] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 9.880388] EXT4-fs (dm-0): mounted filesystem 3beb9788-93c2-45b8-9de8-256936f61783 ro with ordered data mode. Quota mode: disabled. [ 13.778066] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 13.857180] s5p-secss 10830000.sss: s5p-sss driver registered [ 14.019570] mc: Linux media interface: v0.10 [ 14.180157] videodev: Linux video capture interface: v2.00 [ 14.416830] exynos-gsc 13e00000.gsc: Adding to iommu group 0 [ 14.422793] exynos-gsc 13e10000.gsc: Adding to iommu group 1 [ 14.429082] s5p-mfc 11000000.codec: Adding to iommu group 2 [ 14.453974] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 14.465127] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 14.472231] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 14.489959] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.520574] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.528026] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.542874] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 14.548252] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 14.637776] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 14.660498] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.673092] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 14.742456] usb3503 usb-hub: switched to HUB mode [ 14.746172] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.091751] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 15.205355] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.213081] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.221754] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.235894] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 15.243635] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 15.252279] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.304217] hub 2-3:1.0: USB hub found [ 15.307441] hub 2-3:1.0: 3 ports detected [ 15.631728] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 15.784686] hub 2-3.2:1.0: USB hub found [ 15.787615] hub 2-3.2:1.0: 4 ports detected [ 15.823500] usbcore: registered new device driver onboard-usb-dev [ 15.944526] hub 2-3.2:1.0: USB hub found [ 15.947537] hub 2-3.2:1.0: 4 ports detected [ 15.959424] hub 2-3.2:1.0: USB hub found [ 15.962399] hub 2-3.2:1.0: 4 ports detected [ 16.285086] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 16.407600] EXT4-fs (dm-0): re-mounted 3beb9788-93c2-45b8-9de8-256936f61783 r/w. Quota mode: disabled. [ 16.436137] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.133758] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 17.138002] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 17.138620] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 46:4c:63:b5:6d:83 [ 18.028414] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.069099] EXT4-fs (sda1): mounted filesystem 76feffb1-9978-4a90-a9bd-1004dfe30772 r/w with ordered data mode. Quota mode: disabled. [ 18.165611] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 19.991821] xenbr0: port 1(eth0) entered blocking state [ 19.995683] xenbr0: port 1(eth0) entered disabled state [ 20.000996] asix 2-3.2.4:1.0 eth0: entered allmulticast mode [ 20.006902] asix 2-3.2.4:1.0 eth0: entered promiscuous mode [ 20.017754] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 22.262469] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 22.268516] xenbr0: port 1(eth0) entered blocking state [ 22.273746] xenbr0: port 1(eth0) entered forwarding state