[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-25-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.106-3 (2024-08-26) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44820 r8192 d20716 u73728 [ 0.000000] pcpu-alloc: s44820 r8192 d20716 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015504K/2097152K available (12288K kernel code, 1717K rwdata, 3748K rodata, 2048K init, 383K bss, 65264K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39996 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002624] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002638] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002653] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002665] Ignoring duplicate/late registration of read_current_timer delay [ 0.003029] Console: colour dummy device 80x30 [ 0.003072] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003085] CPU: Testing write buffer coherency: ok [ 0.003128] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003136] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003142] pid_max: default: 32768 minimum: 301 [ 0.003512] LSM: Security Framework initializing [ 0.003583] landlock: Up and running. [ 0.003589] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003774] AppArmor: AppArmor initialized [ 0.003786] TOMOYO Linux initialized [ 0.003830] LSM support for eBPF active [ 0.004081] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004095] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005505] /cpus/cpu@0 missing clock-frequency property [ 0.005534] /cpus/cpu@1 missing clock-frequency property [ 0.005547] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006496] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006502] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006606] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006611] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006753] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007915] rcu: Hierarchical SRCU implementation. [ 0.007921] rcu: Max phase no-delay instances is 1000. [ 0.010066] EFI services will not be available. [ 0.010410] smp: Bringing up secondary CPUs ... [ 0.011153] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011165] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011296] smp: Brought up 1 node, 2 CPUs [ 0.011305] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011312] CPU: All CPU(s) started in HYP mode. [ 0.011315] CPU: Virtualization extensions available. [ 0.012167] devtmpfs: initialized [ 0.023166] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023398] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023422] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.023947] pinctrl core: initialized pinctrl subsystem [ 0.024694] DMI not present or invalid. [ 0.025370] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.026917] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028444] audit: initializing netlink subsys (disabled) [ 0.028648] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.029827] thermal_sys: Registered thermal governor 'fair_share' [ 0.029834] thermal_sys: Registered thermal governor 'bang_bang' [ 0.029839] thermal_sys: Registered thermal governor 'step_wise' [ 0.029843] thermal_sys: Registered thermal governor 'user_space' [ 0.029848] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030046] No ATAGs? [ 0.030114] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030123] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031211] Serial: AMBA PL011 UART driver [ 0.080644] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.087635] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091859] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091867] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.099078] iommu: Default domain type: Translated [ 0.099086] iommu: DMA domain TLB invalidation policy: strict mode [ 0.100063] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100578] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100589] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.101126] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.101156] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101381] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.101870] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.101881] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.102259] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102549] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102558] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.102869] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.102969] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.102978] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.103185] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103405] pps_core: LinuxPPS API ver. 1 registered [ 0.103410] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103429] PTP clock support registered [ 0.104938] NetLabel: Initializing [ 0.104945] NetLabel: domain hash size = 128 [ 0.104950] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.105005] NetLabel: unlabeled traffic allowed by default [ 0.105192] vgaarb: loaded [ 0.105742] clocksource: Switched to clocksource mct-frc [ 0.106304] VFS: Disk quotas dquot_6.6.0 [ 0.106389] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107200] AppArmor: AppArmor Filesystem Enabled [ 0.117003] NET: Registered PF_INET protocol family [ 0.117202] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.118853] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.118954] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.118979] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119078] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119309] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119548] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.119639] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119679] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119912] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.119948] NET: Registered PF_XDP protocol family [ 0.119960] PCI: CLS 0 bytes, default 64 [ 0.120460] Trying to unpack rootfs image as initramfs... [ 0.120813] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126226] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.193843] Initialise system trusted keyrings [ 0.193986] Key type blacklist registered [ 0.195205] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.203122] zbud: loaded [ 0.204332] integrity: Platform Keyring initialized [ 0.204364] integrity: Machine keyring initialized [ 0.204373] Key type asymmetric registered [ 0.204381] Asymmetric key parser 'x509' registered [ 1.422010] Freeing initrd memory: 25132K [ 1.444030] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.444294] bounce: pool size: 64 pages [ 1.444473] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.444638] io scheduler mq-deadline registered [ 1.449819] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.470795] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.470808] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473097] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473107] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473927] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473936] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.474750] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474759] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.477071] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.479951] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.482725] Serial: AMBA driver [ 1.482950] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.483425] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.483910] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.564812] printk: console [ttySAC2] enabled [ 2.569629] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.580269] STM32 USART driver initialized [ 2.594694] mousedev: PS/2 mouse device common for all mice [ 2.625959] s5m-rtc s5m-rtc: registered as rtc0 [ 2.634559] s5m-rtc s5m-rtc: setting system clock to 2024-09-16T14:11:17 UTC (1726495877) [ 2.644411] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.651880] ledtrig-cpu: registered to indicate activity on CPUs [ 2.659881] NET: Registered PF_INET6 protocol family [ 2.684001] Segment Routing with IPv6 [ 2.686298] In-situ OAM (IOAM) with IPv6 [ 2.690210] mip6: Mobile IPv6 [ 2.693064] NET: Registered PF_PACKET protocol family [ 2.698256] mpls_gso: MPLS GSO support [ 2.702296] ThumbEE CPU extension supported. [ 2.706108] Registering SWP/SWPB emulation handler [ 2.711370] registered taskstats version 1 [ 2.714970] Loading compiled-in X.509 certificates [ 3.175593] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.182941] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.194046] zswap: loaded using pool lzo/zbud [ 3.197917] Key type .fscrypt registered [ 3.201214] Key type fscrypt-provisioning registered [ 3.225548] Key type encrypted registered [ 3.228144] AppArmor: AppArmor sha1 policy hashing enabled [ 3.233606] ima: No TPM chip found, activating TPM-bypass! [ 3.239071] ima: Allocated hash algorithm: sha256 [ 3.243789] ima: No architecture policies found [ 3.248322] evm: Initialising EVM extended attributes: [ 3.253371] evm: security.selinux [ 3.256660] evm: security.SMACK64 (disabled) [ 3.260910] evm: security.SMACK64EXEC (disabled) [ 3.265511] evm: security.SMACK64TRANSMUTE (disabled) [ 3.270546] evm: security.SMACK64MMAP (disabled) [ 3.275145] evm: security.apparmor [ 3.278530] evm: security.ima [ 3.281467] evm: security.capability [ 3.285046] evm: HMAC attrs: 0x1 [ 3.872499] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.878490] clk: Disabling unused clocks [ 3.891312] Freeing unused kernel image (initmem) memory: 2048K [ 3.896181] Checked W+X mappings: passed, no W+X pages found [ 3.901432] Run /init as init process [ 3.905069] with arguments: [ 3.905076] /init [ 3.905082] with environment: [ 3.905088] HOME=/ [ 3.905093] TERM=linux [ 4.863337] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.883642] usbcore: registered new interface driver usbfs [ 4.887781] usbcore: registered new interface driver hub [ 4.893094] usbcore: registered new device driver usb [ 4.893639] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.908554] Synopsys Designware Multimedia Card Interface Driver [ 4.916752] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 4.928686] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.947924] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.966775] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.992966] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.997983] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.003447] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.008917] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 5.013228] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 5.015246] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 5.021910] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.043059] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.057449] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 5.077803] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.085794] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.107180] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.110126] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.119073] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.126237] usb usb1: Product: EHCI Host Controller [ 5.131105] usb usb1: Manufacturer: Linux 6.1.0-25-armmp-lpae ehci_hcd [ 5.137606] usb usb1: SerialNumber: 12110000.usb [ 5.146217] mmc_host mmc1: card is polling. [ 5.169597] hub 1-0:1.0: USB hub found [ 5.172350] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.179172] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.182842] hub 1-0:1.0: 3 ports detected [ 5.208249] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 5.219499] exynos-ohci 12120000.usb: USB Host Controller [ 5.225512] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.234797] SCSI subsystem initialized [ 5.243512] mmc0: new high speed SDHC card at address aaaa [ 5.255484] libata version 3.00 loaded. [ 5.268103] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.281531] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.288516] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.290910] mmcblk0: mmc0:aaaa SU04G 3.69 GiB [ 5.301367] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.307033] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.315847] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.325188] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.336463] scsi host0: ahci-dwc [ 5.338794] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.364215] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.374825] mmc1: new DDR MMC card at address 0001 [ 5.381064] mmcblk1: mmc1:0001 M4G1FB 3.64 GiB [ 5.397653] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.404493] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.411693] usb usb2: Product: USB Host Controller [ 5.416502] usb usb2: Manufacturer: Linux 6.1.0-25-armmp-lpae ohci_hcd [ 5.422969] usb usb2: SerialNumber: 12120000.usb [ 5.431820] mmcblk1: p1 p2 p3 p4 [ 5.435337] mmcblk1boot0: mmc1:0001 M4G1FB 1.00 MiB [ 5.443719] mmcblk1boot1: mmc1:0001 M4G1FB 1.00 MiB [ 5.449492] hub 2-0:1.0: USB hub found [ 5.451878] hub 2-0:1.0: 3 ports detected [ 5.456842] mmcblk1rpmb: mmc1:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.658283] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.732484] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.825808] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.831382] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.837227] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.840989] I/O error, dev mmcblk0, sector 7743832 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.853822] ata1.00: configured for UDMA/133 [ 5.857919] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.930278] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.934366] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.942773] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 5.954970] I/O error, dev mmcblk0, sector 7743833 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.962969] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 5.969218] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.974323] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.981992] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.988650] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.996707] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.003896] usb usb3: Product: xHCI Host Controller [ 6.008752] usb usb3: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.015263] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.027902] hub 3-0:1.0: USB hub found [ 6.030265] hub 3-0:1.0: 1 port detected [ 6.032086] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.034763] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.041583] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.049884] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.057063] sd 0:0:0:0: [sda] Write Protect is off [ 6.063163] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.067870] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.075065] usb usb4: Product: xHCI Host Controller [ 6.075195] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.079925] usb usb4: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.079933] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.089126] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.095558] I/O error, dev mmcblk0, sector 7743834 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.114160] hub 4-0:1.0: USB hub found [ 6.119805] hub 4-0:1.0: 1 port detected [ 6.125902] sda: sda1 sda2 < sda5 > [ 6.128734] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.215967] I/O error, dev mmcblk0, sector 7743835 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.323941] I/O error, dev mmcblk0, sector 7743836 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.431897] I/O error, dev mmcblk0, sector 7743837 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.539867] I/O error, dev mmcblk0, sector 7743838 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.647848] I/O error, dev mmcblk0, sector 7743839 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 7.056338] I/O error, dev mmcblk0, sector 7743832 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.133764] random: crng init done [ 7.163956] I/O error, dev mmcblk0, sector 7743833 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.250552] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.261469] device-mapper: uevent: version 1.0.3 [ 7.266127] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.772068] Buffer I/O error on dev mmcblk0, logical block 967979, async page read [ 11.034959] PM: Image not found (code -22) [ 11.592217] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.844780] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.189575] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.565944] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.597655] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.740244] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.896798] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.927009] panfrost 11800000.gpu: clock rate = 533000000 [ 15.929911] usb3503 usb-hub: switched to HUB mode [ 15.935655] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.953209] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 15.959527] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 15.967709] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 15.979405] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 15.987894] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 15.997659] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.106182] blk_print_req_error: 6 callbacks suppressed [ 16.106198] I/O error, dev mmcblk0, sector 7743832 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.219595] I/O error, dev mmcblk0, sector 7743833 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.266846] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.327829] I/O error, dev mmcblk0, sector 7743834 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.434672] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.441850] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.453714] I/O error, dev mmcblk0, sector 7743835 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.479672] hub 1-3:1.0: USB hub found [ 16.487454] hub 1-3:1.0: 3 ports detected [ 16.561910] I/O error, dev mmcblk0, sector 7743836 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.577464] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.670090] I/O error, dev mmcblk0, sector 7743837 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.778392] I/O error, dev mmcblk0, sector 7743838 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.793910] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.887357] I/O error, dev mmcblk0, sector 7743839 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.928610] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 16.935754] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 16.942942] usb 1-3.2: Product: USB2.0 Hub [ 16.954081] hub 1-3.2:1.0: USB hub found [ 16.956977] hub 1-3.2:1.0: 4 ports detected [ 17.253925] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.296825] I/O error, dev mmcblk0, sector 7743832 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.372567] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.379847] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.387343] usb 1-3.2.4: Product: AX88772 [ 17.391360] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.396639] usb 1-3.2.4: SerialNumber: 000001 [ 17.417590] I/O error, dev mmcblk0, sector 7743834 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.939544] Buffer I/O error on dev mmcblk0, logical block 967979, async page read [ 17.971014] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.636404] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.651953] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.664009] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 72:51:83:d8:23:46 [ 18.680059] usbcore: registered new interface driver asix [ 19.481305] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.327017] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.378987] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 21.572773] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 22.831935] audit: type=1400 audit(1726495896.820:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=886 comm="apparmor_parser" [ 22.850454] audit: type=1400 audit(1726495896.836:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=887 comm="apparmor_parser" [ 22.865309] audit: type=1400 audit(1726495896.840:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=887 comm="apparmor_parser" [ 23.446768] audit: type=1400 audit(1726495897.436:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=929 comm="apparmor_parser" [ 23.462316] audit: type=1400 audit(1726495897.436:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=929 comm="apparmor_parser" [ 23.475762] audit: type=1400 audit(1726495897.440:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=929 comm="apparmor_parser" [ 23.606060] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.882375] audit: type=1400 audit(1726495897.872:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/ntpd" pid=939 comm="apparmor_parser" [ 23.897482] audit: type=1400 audit(1726495897.876:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=925 comm="apparmor_parser" [ 23.914033] audit: type=1400 audit(1726495897.880:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=925 comm="apparmor_parser" [ 23.931364] audit: type=1400 audit(1726495897.884:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=925 comm="apparmor_parser" [ 25.767746] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.773894] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.897081] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.908080] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.915871] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.922253] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.930828] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.940155] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.946996] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.965877] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.973273] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.980923] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1