[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-25-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.106-3 (2024-08-26) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44820 r8192 d20716 u73728 [ 0.000000] pcpu-alloc: s44820 r8192 d20716 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015504K/2097152K available (12288K kernel code, 1717K rwdata, 3748K rodata, 2048K init, 383K bss, 65264K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39996 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000018] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002625] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002640] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002655] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002666] Ignoring duplicate/late registration of read_current_timer delay [ 0.003032] Console: colour dummy device 80x30 [ 0.003073] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003087] CPU: Testing write buffer coherency: ok [ 0.003129] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003138] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003144] pid_max: default: 32768 minimum: 301 [ 0.003514] LSM: Security Framework initializing [ 0.003587] landlock: Up and running. [ 0.003592] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003777] AppArmor: AppArmor initialized [ 0.003790] TOMOYO Linux initialized [ 0.003835] LSM support for eBPF active [ 0.004086] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004100] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005519] /cpus/cpu@0 missing clock-frequency property [ 0.005547] /cpus/cpu@1 missing clock-frequency property [ 0.005561] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006512] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006519] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006621] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006627] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006766] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007931] rcu: Hierarchical SRCU implementation. [ 0.007936] rcu: Max phase no-delay instances is 1000. [ 0.010068] EFI services will not be available. [ 0.010411] smp: Bringing up secondary CPUs ... [ 0.011156] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011168] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011311] smp: Brought up 1 node, 2 CPUs [ 0.011319] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011327] CPU: All CPU(s) started in HYP mode. [ 0.011331] CPU: Virtualization extensions available. [ 0.012186] devtmpfs: initialized [ 0.023239] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023474] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023498] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024044] pinctrl core: initialized pinctrl subsystem [ 0.024764] DMI not present or invalid. [ 0.025438] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.026983] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028509] audit: initializing netlink subsys (disabled) [ 0.028711] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.029892] thermal_sys: Registered thermal governor 'fair_share' [ 0.029899] thermal_sys: Registered thermal governor 'bang_bang' [ 0.029904] thermal_sys: Registered thermal governor 'step_wise' [ 0.029909] thermal_sys: Registered thermal governor 'user_space' [ 0.029913] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030114] No ATAGs? [ 0.030183] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030192] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031274] Serial: AMBA PL011 UART driver [ 0.080656] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.087630] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091854] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091862] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.098968] iommu: Default domain type: Translated [ 0.098976] iommu: DMA domain TLB invalidation policy: strict mode [ 0.099950] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100463] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100474] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.101010] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.101039] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101273] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.101765] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.101776] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.102158] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102451] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102460] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.102772] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.102872] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.102881] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.103059] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103302] pps_core: LinuxPPS API ver. 1 registered [ 0.103308] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103324] PTP clock support registered [ 0.104848] NetLabel: Initializing [ 0.104854] NetLabel: domain hash size = 128 [ 0.104859] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.104913] NetLabel: unlabeled traffic allowed by default [ 0.105103] vgaarb: loaded [ 0.105759] clocksource: Switched to clocksource mct-frc [ 0.106317] VFS: Disk quotas dquot_6.6.0 [ 0.106400] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107207] AppArmor: AppArmor Filesystem Enabled [ 0.117007] NET: Registered PF_INET protocol family [ 0.117199] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.118823] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.118920] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.118944] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119043] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119273] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119512] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.119603] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119644] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119878] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.119914] NET: Registered PF_XDP protocol family [ 0.119927] PCI: CLS 0 bytes, default 64 [ 0.120417] Trying to unpack rootfs image as initramfs... [ 0.120763] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126101] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.193195] Initialise system trusted keyrings [ 0.193285] Key type blacklist registered [ 0.194546] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.202465] zbud: loaded [ 0.203848] integrity: Platform Keyring initialized [ 0.203891] integrity: Machine keyring initialized [ 0.203901] Key type asymmetric registered [ 0.203908] Asymmetric key parser 'x509' registered [ 1.419231] Freeing initrd memory: 25132K [ 1.441519] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.441824] bounce: pool size: 64 pages [ 1.442008] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.442186] io scheduler mq-deadline registered [ 1.447278] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.468212] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.468225] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.470601] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.470610] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.471403] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.471413] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.472218] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.472226] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.474566] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.477374] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.480140] Serial: AMBA driver [ 1.480364] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.480835] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.481316] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.562211] printk: console [ttySAC2] enabled [ 2.567021] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.577665] STM32 USART driver initialized [ 2.592110] mousedev: PS/2 mouse device common for all mice [ 2.623385] s5m-rtc s5m-rtc: registered as rtc0 [ 2.632015] s5m-rtc s5m-rtc: setting system clock to 2024-09-17T08:16:22 UTC (1726560982) [ 2.641856] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.649301] ledtrig-cpu: registered to indicate activity on CPUs [ 2.657275] NET: Registered PF_INET6 protocol family [ 2.681263] Segment Routing with IPv6 [ 2.683557] In-situ OAM (IOAM) with IPv6 [ 2.687491] mip6: Mobile IPv6 [ 2.690370] NET: Registered PF_PACKET protocol family [ 2.695495] mpls_gso: MPLS GSO support [ 2.699558] ThumbEE CPU extension supported. [ 2.703363] Registering SWP/SWPB emulation handler [ 2.708631] registered taskstats version 1 [ 2.712262] Loading compiled-in X.509 certificates [ 3.172909] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.180249] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.191366] zswap: loaded using pool lzo/zbud [ 3.195229] Key type .fscrypt registered [ 3.198582] Key type fscrypt-provisioning registered [ 3.222865] Key type encrypted registered [ 3.225407] AppArmor: AppArmor sha1 policy hashing enabled [ 3.230957] ima: No TPM chip found, activating TPM-bypass! [ 3.236367] ima: Allocated hash algorithm: sha256 [ 3.241092] ima: No architecture policies found [ 3.245634] evm: Initialising EVM extended attributes: [ 3.250684] evm: security.selinux [ 3.253975] evm: security.SMACK64 (disabled) [ 3.258222] evm: security.SMACK64EXEC (disabled) [ 3.262823] evm: security.SMACK64TRANSMUTE (disabled) [ 3.267856] evm: security.SMACK64MMAP (disabled) [ 3.272456] evm: security.apparmor [ 3.275841] evm: security.ima [ 3.278793] evm: security.capability [ 3.282358] evm: HMAC attrs: 0x1 [ 3.870200] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.876145] clk: Disabling unused clocks [ 3.889024] Freeing unused kernel image (initmem) memory: 2048K [ 3.893933] Checked W+X mappings: passed, no W+X pages found [ 3.899142] Run /init as init process [ 3.902777] with arguments: [ 3.902783] /init [ 3.902790] with environment: [ 3.902795] HOME=/ [ 3.902800] TERM=linux [ 4.780553] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.787639] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.803578] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.813139] usbcore: registered new interface driver usbfs [ 4.817619] usbcore: registered new interface driver hub [ 4.826813] usbcore: registered new device driver usb [ 4.835911] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 4.841994] exynos-ehci 12110000.usb: EHCI Host Controller [ 4.852601] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 4.860670] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 4.866560] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 4.872823] Synopsys Designware Multimedia Card Interface Driver [ 4.888778] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.895167] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.901271] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.907526] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.915168] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.919999] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 4.920191] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.926221] exynos-ohci 12120000.usb: USB Host Controller [ 4.941686] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 4.948550] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.955738] usb usb1: Product: EHCI Host Controller [ 4.960572] usb usb1: Manufacturer: Linux 6.1.0-25-armmp-lpae ehci_hcd [ 4.967081] usb usb1: SerialNumber: 12110000.usb [ 4.976495] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 4.999646] mmc_host mmc0: card is polling. [ 5.003256] hub 1-0:1.0: USB hub found [ 5.006178] hub 1-0:1.0: 3 ports detected [ 5.012936] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.013692] SCSI subsystem initialized [ 5.019229] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.037133] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.046640] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.063987] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.076337] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.102057] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.108924] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.116094] usb usb2: Product: USB Host Controller [ 5.120865] usb usb2: Manufacturer: Linux 6.1.0-25-armmp-lpae ohci_hcd [ 5.127365] usb usb2: SerialNumber: 12120000.usb [ 5.178564] hub 2-0:1.0: USB hub found [ 5.182549] libata version 3.00 loaded. [ 5.196325] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.216739] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.225429] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.242625] hub 2-0:1.0: 3 ports detected [ 5.259857] mmc1: new high speed SDHC card at address aaaa [ 5.273025] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.281083] mmc0: new DDR MMC card at address 0001 [ 5.297015] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.301182] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.307567] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.344949] mmcblk0: p1 p2 p3 p4 [ 5.354486] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.360134] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.368939] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.387208] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.408473] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.418333] scsi host0: ahci-dwc [ 5.420897] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.425457] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.756598] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.829895] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.909804] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.915366] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.921217] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.928674] ata1.00: configured for UDMA/133 [ 5.932593] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.938400] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.953007] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.957184] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.969397] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 5.977418] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 5.983586] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.988809] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.996444] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.003106] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.011200] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.018403] usb usb3: Product: xHCI Host Controller [ 6.023256] usb usb3: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.029768] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.035808] hub 3-0:1.0: USB hub found [ 6.038408] hub 3-0:1.0: 1 port detected [ 6.043262] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.050445] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.054011] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.067885] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.075084] usb usb4: Product: xHCI Host Controller [ 6.079943] usb usb4: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.086455] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.091886] hub 4-0:1.0: USB hub found [ 6.095087] hub 4-0:1.0: 1 port detected [ 6.144797] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.150869] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.156875] sd 0:0:0:0: [sda] Write Protect is off [ 6.159746] I/O error, dev mmcblk1, sector 7743834 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.160859] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.170956] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.179258] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.199273] sda: sda1 sda2 < sda5 > [ 6.205148] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.270205] I/O error, dev mmcblk1, sector 7743835 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.379273] I/O error, dev mmcblk1, sector 7743836 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.487285] I/O error, dev mmcblk1, sector 7743837 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.595263] I/O error, dev mmcblk1, sector 7743838 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.703278] I/O error, dev mmcblk1, sector 7743839 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 7.111750] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.219356] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.277783] random: crng init done [ 7.388738] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.399559] device-mapper: uevent: version 1.0.3 [ 7.404303] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.827456] Buffer I/O error on dev mmcblk1, logical block 967979, async page read [ 11.197462] PM: Image not found (code -22) [ 11.771162] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.007357] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.352929] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.910391] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.940235] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 16.074369] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 16.297369] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.353798] usb3503 usb-hub: switched to HUB mode [ 16.357078] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.368858] panfrost 11800000.gpu: clock rate = 533000000 [ 16.371997] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.470011] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 16.476373] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 16.482760] blk_print_req_error: 6 callbacks suppressed [ 16.482774] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.484495] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 16.510728] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 16.519516] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 16.589968] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.681974] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.698124] I/O error, dev mmcblk1, sector 7743834 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.806736] I/O error, dev mmcblk1, sector 7743835 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.848736] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.855566] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.870312] hub 1-3:1.0: USB hub found [ 16.874213] hub 1-3:1.0: 3 ports detected [ 16.914964] I/O error, dev mmcblk1, sector 7743836 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.023033] I/O error, dev mmcblk1, sector 7743837 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.131197] I/O error, dev mmcblk1, sector 7743838 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.153882] OF: graph: no port node found in /soc/hdmi@14530000 [ 17.169853] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.239333] I/O error, dev mmcblk1, sector 7743839 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.287646] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 17.294877] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 17.301947] usb 1-3.2: Product: USB2.0 Hub [ 17.309311] hub 1-3.2:1.0: USB hub found [ 17.312310] hub 1-3.2:1.0: 4 ports detected [ 17.614727] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.667827] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.743783] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.750935] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.758398] usb 1-3.2.4: Product: AX88772 [ 17.762483] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.767652] usb 1-3.2.4: SerialNumber: 000001 [ 17.788635] I/O error, dev mmcblk1, sector 7743835 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 18.212382] Buffer I/O error on dev mmcblk1, logical block 967979, async page read [ 18.325583] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 19.032442] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 19.047981] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 19.059809] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 5a:e1:14:5b:67:e9 [ 19.078136] usbcore: registered new interface driver asix [ 19.966129] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 22.378471] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 22.430707] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 22.655918] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 24.067467] audit: type=1400 audit(1726561003.916:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=900 comm="apparmor_parser" [ 24.089446] audit: type=1400 audit(1726561003.936:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=901 comm="apparmor_parser" [ 24.105508] audit: type=1400 audit(1726561003.936:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=901 comm="apparmor_parser" [ 24.173849] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.444372] audit: type=1400 audit(1726561004.292:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=944 comm="apparmor_parser" [ 24.458584] audit: type=1400 audit(1726561004.292:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=944 comm="apparmor_parser" [ 24.472829] audit: type=1400 audit(1726561004.292:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=944 comm="apparmor_parser" [ 24.783622] audit: type=1400 audit(1726561004.632:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=943 comm="apparmor_parser" [ 24.801899] audit: type=1400 audit(1726561004.632:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=943 comm="apparmor_parser" [ 24.817791] audit: type=1400 audit(1726561004.632:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=943 comm="apparmor_parser" [ 24.835301] audit: type=1400 audit(1726561004.632:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=943 comm="apparmor_parser" [ 26.343518] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 26.343641] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 29.153152] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 29.164792] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 29.172676] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 29.179068] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 29.187623] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 29.197247] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 29.203937] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 29.213027] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.219348] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 29.234195] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1