[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-25-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.106-3 (2024-08-26) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44820 r8192 d20716 u73728 [ 0.000000] pcpu-alloc: s44820 r8192 d20716 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015504K/2097152K available (12288K kernel code, 1717K rwdata, 3748K rodata, 2048K init, 383K bss, 65264K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39996 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002627] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002641] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002656] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002667] Ignoring duplicate/late registration of read_current_timer delay [ 0.003030] Console: colour dummy device 80x30 [ 0.003072] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003085] CPU: Testing write buffer coherency: ok [ 0.003126] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003134] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003140] pid_max: default: 32768 minimum: 301 [ 0.003508] LSM: Security Framework initializing [ 0.003580] landlock: Up and running. [ 0.003585] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003771] AppArmor: AppArmor initialized [ 0.003783] TOMOYO Linux initialized [ 0.003828] LSM support for eBPF active [ 0.004075] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004089] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005496] /cpus/cpu@0 missing clock-frequency property [ 0.005523] /cpus/cpu@1 missing clock-frequency property [ 0.005537] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006491] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006497] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006599] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006604] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006745] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007911] rcu: Hierarchical SRCU implementation. [ 0.007917] rcu: Max phase no-delay instances is 1000. [ 0.010046] EFI services will not be available. [ 0.010388] smp: Bringing up secondary CPUs ... [ 0.011124] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011136] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011265] smp: Brought up 1 node, 2 CPUs [ 0.011274] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011282] CPU: All CPU(s) started in HYP mode. [ 0.011285] CPU: Virtualization extensions available. [ 0.012134] devtmpfs: initialized [ 0.023079] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023309] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023332] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.023861] pinctrl core: initialized pinctrl subsystem [ 0.024613] DMI not present or invalid. [ 0.025290] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.026832] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028358] audit: initializing netlink subsys (disabled) [ 0.028560] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.029742] thermal_sys: Registered thermal governor 'fair_share' [ 0.029750] thermal_sys: Registered thermal governor 'bang_bang' [ 0.029755] thermal_sys: Registered thermal governor 'step_wise' [ 0.029759] thermal_sys: Registered thermal governor 'user_space' [ 0.029763] thermal_sys: Registered thermal governor 'power_allocator' [ 0.029964] No ATAGs? [ 0.030031] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030040] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031126] Serial: AMBA PL011 UART driver [ 0.080591] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.087541] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091828] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091836] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.099009] iommu: Default domain type: Translated [ 0.099016] iommu: DMA domain TLB invalidation policy: strict mode [ 0.099994] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100503] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100514] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.101054] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.101086] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101313] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.101808] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.101819] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.102202] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102495] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102505] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.102816] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.102914] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.102923] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.103102] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103349] pps_core: LinuxPPS API ver. 1 registered [ 0.103355] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103372] PTP clock support registered [ 0.104913] NetLabel: Initializing [ 0.104919] NetLabel: domain hash size = 128 [ 0.104924] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.104979] NetLabel: unlabeled traffic allowed by default [ 0.105152] vgaarb: loaded [ 0.105682] clocksource: Switched to clocksource mct-frc [ 0.106240] VFS: Disk quotas dquot_6.6.0 [ 0.106324] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107092] AppArmor: AppArmor Filesystem Enabled [ 0.116958] NET: Registered PF_INET protocol family [ 0.117152] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.118782] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.118883] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.118907] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119013] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119244] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119474] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.119570] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119610] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.119847] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.119882] NET: Registered PF_XDP protocol family [ 0.119894] PCI: CLS 0 bytes, default 64 [ 0.120407] Trying to unpack rootfs image as initramfs... [ 0.120744] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126159] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.193752] Initialise system trusted keyrings [ 0.193887] Key type blacklist registered [ 0.195057] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.203022] zbud: loaded [ 0.204197] integrity: Platform Keyring initialized [ 0.204258] integrity: Machine keyring initialized [ 0.204267] Key type asymmetric registered [ 0.204275] Asymmetric key parser 'x509' registered [ 1.422445] Freeing initrd memory: 25132K [ 1.444501] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.444766] bounce: pool size: 64 pages [ 1.444945] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.445108] io scheduler mq-deadline registered [ 1.450272] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.471155] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.471166] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473468] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473478] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.474306] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474315] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.475141] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.475150] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.477494] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.480346] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.483136] Serial: AMBA driver [ 1.483361] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.483831] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.484297] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.565045] printk: console [ttySAC2] enabled [ 2.569880] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.580502] STM32 USART driver initialized [ 2.594941] mousedev: PS/2 mouse device common for all mice [ 2.626208] s5m-rtc s5m-rtc: registered as rtc0 [ 2.634810] s5m-rtc s5m-rtc: setting system clock to 2024-09-17T16:13:49 UTC (1726589629) [ 2.644664] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.652117] ledtrig-cpu: registered to indicate activity on CPUs [ 2.660120] NET: Registered PF_INET6 protocol family [ 2.684287] Segment Routing with IPv6 [ 2.686552] In-situ OAM (IOAM) with IPv6 [ 2.690478] mip6: Mobile IPv6 [ 2.693345] NET: Registered PF_PACKET protocol family [ 2.698509] mpls_gso: MPLS GSO support [ 2.702558] ThumbEE CPU extension supported. [ 2.706391] Registering SWP/SWPB emulation handler [ 2.711633] registered taskstats version 1 [ 2.715253] Loading compiled-in X.509 certificates [ 3.175369] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.182727] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.193829] zswap: loaded using pool lzo/zbud [ 3.197671] Key type .fscrypt registered [ 3.201013] Key type fscrypt-provisioning registered [ 3.225250] Key type encrypted registered [ 3.227849] AppArmor: AppArmor sha1 policy hashing enabled [ 3.233332] ima: No TPM chip found, activating TPM-bypass! [ 3.238780] ima: Allocated hash algorithm: sha256 [ 3.243460] ima: No architecture policies found [ 3.248021] evm: Initialising EVM extended attributes: [ 3.253067] evm: security.selinux [ 3.256367] evm: security.SMACK64 (disabled) [ 3.260612] evm: security.SMACK64EXEC (disabled) [ 3.265214] evm: security.SMACK64TRANSMUTE (disabled) [ 3.270249] evm: security.SMACK64MMAP (disabled) [ 3.274847] evm: security.apparmor [ 3.278231] evm: security.ima [ 3.281167] evm: security.capability [ 3.284748] evm: HMAC attrs: 0x1 [ 3.872378] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.878370] clk: Disabling unused clocks [ 3.891198] Freeing unused kernel image (initmem) memory: 2048K [ 3.896076] Checked W+X mappings: passed, no W+X pages found [ 3.901316] Run /init as init process [ 3.904948] with arguments: [ 3.904956] /init [ 3.904962] with environment: [ 3.904967] HOME=/ [ 3.904973] TERM=linux [ 4.819743] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.834061] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.865471] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.869337] usbcore: registered new interface driver usbfs [ 4.899675] Synopsys Designware Multimedia Card Interface Driver [ 4.913297] SCSI subsystem initialized [ 4.921810] usbcore: registered new interface driver hub [ 4.937823] usbcore: registered new device driver usb [ 4.943391] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.949726] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.955747] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.962136] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.973406] s2mps11-clk s5m8767-clk: DMA mask not set [ 4.980916] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.985946] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.029164] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107,32 bit host data width,128 deep fifo [ 5.035291] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.042210] mmc_host mmc0: card is polling. [ 5.093802] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.108426] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.145574] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 5.169323] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 5.179821] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.180505] exynos-ohci 12120000.usb: USB Host Controller [ 5.192046] libata version 3.00 loaded. [ 5.204006] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.204637] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 5.210233] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.217831] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.225496] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.242317] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.257243] exynos-ohci 12120000.usb: irq 109, io mem 0x12120000 [ 5.261885] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.267249] mmc0: new DDR MMC card at address 0001 [ 5.276741] exynos-ehci 12110000.usb: irq 109, io mem 0x12110000 [ 5.285429] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.292545] mmc1: new high speed SDHC card at address aaaa [ 5.298315] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.298413] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.303947] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.311481] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.318758] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.336139] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.343354] usb usb1: Product: EHCI Host Controller [ 5.346625] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.348210] usb usb1: Manufacturer: Linux 6.1.0-25-armmp-lpae ehci_hcd [ 5.359129] usb usb1: SerialNumber: 12110000.usb [ 5.364661] mmcblk0: p1 p2 p3 p4 [ 5.369741] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.376406] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.380990] hub 1-0:1.0: USB hub found [ 5.383741] hub 1-0:1.0: 3 ports detected [ 5.389911] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.396125] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.402958] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.410150] usb usb2: Product: USB Host Controller [ 5.414928] usb usb2: Manufacturer: Linux 6.1.0-25-armmp-lpae ohci_hcd [ 5.421431] usb usb2: SerialNumber: 12120000.usb [ 5.443839] hub 2-0:1.0: USB hub found [ 5.449909] hub 2-0:1.0: 3 ports detected [ 5.454137] scsi host0: ahci-dwc [ 5.456544] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.671811] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.745106] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.853555] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.937752] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.943360] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.949168] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.956668] ata1.00: configured for UDMA/133 [ 5.960548] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.961535] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.017572] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.025074] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 6.031874] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.040776] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.046954] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.052164] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.059789] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.066479] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.074515] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.081728] usb usb3: Product: xHCI Host Controller [ 6.086564] usb usb3: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.093071] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.098001] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.113711] hub 3-0:1.0: USB hub found [ 6.116040] hub 3-0:1.0: 1 port detected [ 6.121268] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.128161] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.136257] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.143472] usb usb4: Product: xHCI Host Controller [ 6.148303] usb usb4: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.154818] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.162583] hub 4-0:1.0: USB hub found [ 6.163358] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.165839] hub 4-0:1.0: 1 port detected [ 6.172394] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.181867] sd 0:0:0:0: [sda] Write Protect is off [ 6.186256] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.186363] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.195396] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.207348] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.230434] sda: sda1 sda2 < sda5 > [ 6.233262] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.315324] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.423272] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.531308] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.639303] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 7.047757] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.155345] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.241707] random: crng init done [ 7.352247] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.363206] device-mapper: uevent: version 1.0.3 [ 7.369753] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.763449] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 11.088251] PM: Image not found (code -22) [ 11.558182] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.747863] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.067276] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.255903] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.261670] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.370155] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.561804] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.593739] usb3503 usb-hub: switched to HUB mode [ 15.596979] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.632708] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.678548] panfrost 11800000.gpu: clock rate = 533000000 [ 15.735195] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 15.741640] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 15.749700] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 15.761424] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 15.767802] blk_print_req_error: 6 callbacks suppressed [ 15.767811] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 15.782849] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 15.882571] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 15.917803] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 15.990814] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.087611] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.094577] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.105981] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.118951] hub 1-3:1.0: USB hub found [ 16.121627] hub 1-3:1.0: 3 ports detected [ 16.214338] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.302502] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.322555] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.430782] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.473766] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.538948] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.595839] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 16.602985] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 16.610182] usb 1-3.2: Product: USB2.0 Hub [ 16.619008] hub 1-3.2:1.0: USB hub found [ 16.622113] hub 1-3.2:1.0: 4 ports detected [ 16.933887] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 16.948919] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.052422] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.059883] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.067377] usb 1-3.2.4: Product: AX88772 [ 17.071298] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.076367] usb 1-3.2.4: SerialNumber: 000001 [ 17.080977] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.588361] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.691813] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 18.264206] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.279763] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.293575] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 8a:74:1b:01:92:80 [ 18.308395] usbcore: registered new interface driver asix [ 19.063345] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.376592] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.425258] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 21.701274] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 22.875606] audit: type=1400 audit(1726589649.084:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=892 comm="apparmor_parser" [ 22.895622] audit: type=1400 audit(1726589649.100:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=891 comm="apparmor_parser" [ 22.909224] audit: type=1400 audit(1726589649.100:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=892 comm="apparmor_parser" [ 23.126006] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.261071] audit: type=1400 audit(1726589649.468:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=932 comm="apparmor_parser" [ 23.280515] audit: type=1400 audit(1726589649.484:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=932 comm="apparmor_parser" [ 23.293970] audit: type=1400 audit(1726589649.488:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=932 comm="apparmor_parser" [ 23.632809] audit: type=1400 audit(1726589649.840:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/ntpd" pid=943 comm="apparmor_parser" [ 23.670106] audit: type=1400 audit(1726589649.880:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=931 comm="apparmor_parser" [ 23.686778] audit: type=1400 audit(1726589649.884:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=931 comm="apparmor_parser" [ 23.703924] audit: type=1400 audit(1726589649.888:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=931 comm="apparmor_parser" [ 25.287446] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.293596] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.385028] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.396088] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.403821] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.410178] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.418634] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.428235] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.435025] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.446748] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.452720] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.462979] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1