[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-25-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.106-3 (2024-08-26) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44820 r8192 d20716 u73728 [ 0.000000] pcpu-alloc: s44820 r8192 d20716 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--metrocentre--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015504K/2097152K available (12288K kernel code, 1717K rwdata, 3748K rodata, 2048K init, 383K bss, 65264K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39996 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000019] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002625] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002640] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002654] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002666] Ignoring duplicate/late registration of read_current_timer delay [ 0.003033] Console: colour dummy device 80x30 [ 0.003075] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003089] CPU: Testing write buffer coherency: ok [ 0.003130] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003138] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003145] pid_max: default: 32768 minimum: 301 [ 0.003513] LSM: Security Framework initializing [ 0.003585] landlock: Up and running. [ 0.003590] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003777] AppArmor: AppArmor initialized [ 0.003790] TOMOYO Linux initialized [ 0.003836] LSM support for eBPF active [ 0.004085] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004100] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005519] /cpus/cpu@0 missing clock-frequency property [ 0.005546] /cpus/cpu@1 missing clock-frequency property [ 0.005560] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006506] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006513] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006615] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006620] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006759] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007917] rcu: Hierarchical SRCU implementation. [ 0.007923] rcu: Max phase no-delay instances is 1000. [ 0.010056] EFI services will not be available. [ 0.010399] smp: Bringing up secondary CPUs ... [ 0.011140] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011151] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011284] smp: Brought up 1 node, 2 CPUs [ 0.011293] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011301] CPU: All CPU(s) started in HYP mode. [ 0.011305] CPU: Virtualization extensions available. [ 0.012157] devtmpfs: initialized [ 0.023158] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023388] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023413] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.023955] pinctrl core: initialized pinctrl subsystem [ 0.024711] DMI not present or invalid. [ 0.025389] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.026942] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028466] audit: initializing netlink subsys (disabled) [ 0.028670] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.029857] thermal_sys: Registered thermal governor 'fair_share' [ 0.029864] thermal_sys: Registered thermal governor 'bang_bang' [ 0.029869] thermal_sys: Registered thermal governor 'step_wise' [ 0.029874] thermal_sys: Registered thermal governor 'user_space' [ 0.029878] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030078] No ATAGs? [ 0.030145] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030153] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031241] Serial: AMBA PL011 UART driver [ 0.080626] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.087607] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091738] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091746] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.099306] iommu: Default domain type: Translated [ 0.099314] iommu: DMA domain TLB invalidation policy: strict mode [ 0.100292] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100803] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100814] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.101329] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.101359] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101601] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.102093] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.102104] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.102474] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102766] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102776] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.103068] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.103224] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.103234] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.103418] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103636] pps_core: LinuxPPS API ver. 1 registered [ 0.103642] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103658] PTP clock support registered [ 0.105153] NetLabel: Initializing [ 0.105158] NetLabel: domain hash size = 128 [ 0.105163] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.105217] NetLabel: unlabeled traffic allowed by default [ 0.105389] vgaarb: loaded [ 0.106219] clocksource: Switched to clocksource mct-frc [ 0.106801] VFS: Disk quotas dquot_6.6.0 [ 0.106885] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107696] AppArmor: AppArmor Filesystem Enabled [ 0.117528] NET: Registered PF_INET protocol family [ 0.117731] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.119364] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.119463] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.119490] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119591] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119821] TCP: Hash tables configured (established 8192 bind 8192) [ 0.120054] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.120147] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120188] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120438] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.120472] NET: Registered PF_XDP protocol family [ 0.120483] PCI: CLS 0 bytes, default 64 [ 0.120973] Trying to unpack rootfs image as initramfs... [ 0.121334] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.126743] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.194417] Initialise system trusted keyrings [ 0.194487] Key type blacklist registered [ 0.195734] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.203742] zbud: loaded [ 0.205011] integrity: Platform Keyring initialized [ 0.205053] integrity: Machine keyring initialized [ 0.205062] Key type asymmetric registered [ 0.205070] Asymmetric key parser 'x509' registered [ 1.423432] Freeing initrd memory: 25132K [ 1.445606] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.445872] bounce: pool size: 64 pages [ 1.446061] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.446267] io scheduler mq-deadline registered [ 1.451430] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.472379] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.472391] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.474730] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474741] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.475547] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.475556] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.476376] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.476385] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.478747] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.481555] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.484328] Serial: AMBA driver [ 1.484551] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.485026] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.485492] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.566393] printk: console [ttySAC2] enabled [ 2.571226] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.581838] STM32 USART driver initialized [ 2.596214] mousedev: PS/2 mouse device common for all mice [ 2.627514] s5m-rtc s5m-rtc: registered as rtc0 [ 2.636152] s5m-rtc s5m-rtc: setting system clock to 2024-09-19T01:15:05 UTC (1726708505) [ 2.645974] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.653412] ledtrig-cpu: registered to indicate activity on CPUs [ 2.661411] NET: Registered PF_INET6 protocol family [ 2.685386] Segment Routing with IPv6 [ 2.687657] In-situ OAM (IOAM) with IPv6 [ 2.691589] mip6: Mobile IPv6 [ 2.694461] NET: Registered PF_PACKET protocol family [ 2.699610] mpls_gso: MPLS GSO support [ 2.703656] ThumbEE CPU extension supported. [ 2.707487] Registering SWP/SWPB emulation handler [ 2.712753] registered taskstats version 1 [ 2.716352] Loading compiled-in X.509 certificates [ 3.177261] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.184608] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.195688] zswap: loaded using pool lzo/zbud [ 3.199589] Key type .fscrypt registered [ 3.202930] Key type fscrypt-provisioning registered [ 3.227264] Key type encrypted registered [ 3.229813] AppArmor: AppArmor sha1 policy hashing enabled [ 3.235360] ima: No TPM chip found, activating TPM-bypass! [ 3.240777] ima: Allocated hash algorithm: sha256 [ 3.245521] ima: No architecture policies found [ 3.250019] evm: Initialising EVM extended attributes: [ 3.255090] evm: security.selinux [ 3.258382] evm: security.SMACK64 (disabled) [ 3.262629] evm: security.SMACK64EXEC (disabled) [ 3.267230] evm: security.SMACK64TRANSMUTE (disabled) [ 3.272263] evm: security.SMACK64MMAP (disabled) [ 3.276864] evm: security.apparmor [ 3.280249] evm: security.ima [ 3.283200] evm: security.capability [ 3.286764] evm: HMAC attrs: 0x1 [ 3.874268] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.880216] clk: Disabling unused clocks [ 3.893098] Freeing unused kernel image (initmem) memory: 2048K [ 3.897974] Checked W+X mappings: passed, no W+X pages found [ 3.903222] Run /init as init process [ 3.906848] with arguments: [ 3.906855] /init [ 3.906861] with environment: [ 3.906866] HOME=/ [ 3.906872] TERM=linux [ 4.794048] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.822787] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.842615] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.844894] usbcore: registered new interface driver usbfs [ 4.886411] Synopsys Designware Multimedia Card Interface Driver [ 4.901278] usbcore: registered new interface driver hub [ 4.908777] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.914697] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.922050] SCSI subsystem initialized [ 4.926905] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.931922] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.932821] usbcore: registered new device driver usb [ 4.950330] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.955421] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.960859] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107,32 bit host data width,128 deep fifo [ 4.993778] s2mps11-clk s5m8767-clk: DMA mask not set [ 4.995331] mmc_host mmc0: card is polling. [ 5.006162] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.018288] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.058281] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.096211] phy phy-12130000.phy.1: phy_power_on was called before phy_init [ 5.114139] phy phy-12130000.phy.1: phy_power_on was called before phy_init [ 5.123572] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.136944] exynos-ohci 12120000.usb: USB Host Controller [ 5.141675] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 5.144667] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.160402] libata version 3.00 loaded. [ 5.167809] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.174526] exynos-ehci 12110000.usb: irq 109, io mem 0x12110000 [ 5.180234] exynos-ohci 12120000.usb: irq 109, io mem 0x12120000 [ 5.182161] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.190505] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.202775] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.204114] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.209151] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.226726] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.233930] usb usb1: Product: EHCI Host Controller [ 5.238779] usb usb1: Manufacturer: Linux 6.1.0-25-armmp-lpae ehci_hcd [ 5.245302] usb usb1: SerialNumber: 12110000.usb [ 5.255852] hub 1-0:1.0: USB hub found [ 5.258116] mmc1: new high speed SDHC card at address aaaa [ 5.258173] hub 1-0:1.0: 3 ports detected [ 5.263947] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.268866] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.283429] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.290651] usb usb2: Product: USB Host Controller [ 5.295397] usb usb2: Manufacturer: Linux 6.1.0-25-armmp-lpae ohci_hcd [ 5.301904] usb usb2: SerialNumber: 12120000.usb [ 5.304402] mmc0: new DDR MMC card at address 0001 [ 5.312082] hub 2-0:1.0: USB hub found [ 5.316274] hub 2-0:1.0: 3 ports detected [ 5.323235] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.340311] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.355712] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.361375] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.370181] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.386885] mmcblk0: p1 p2 p3 p4 [ 5.392217] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.395988] scsi host0: ahci-dwc [ 5.399840] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.401781] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.459969] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.705692] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.778959] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.887400] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.890319] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.902263] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.908108] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.915567] ata1.00: configured for UDMA/133 [ 5.919495] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.972547] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.976808] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.984816] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 5.993639] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 5.999732] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.009078] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.014428] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.022155] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.028685] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.036749] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.043937] usb usb3: Product: xHCI Host Controller [ 6.048804] usb usb3: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.055312] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.061521] hub 3-0:1.0: USB hub found [ 6.064761] hub 3-0:1.0: 1 port detected [ 6.070342] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.077238] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.085614] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.092457] usb usb4: Product: xHCI Host Controller [ 6.097299] usb usb4: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.103809] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.108986] I/O error, dev mmcblk1, sector 7743834 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.120496] hub 4-0:1.0: USB hub found [ 6.122861] hub 4-0:1.0: 1 port detected [ 6.123768] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.134175] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.142885] sd 0:0:0:0: [sda] Write Protect is off [ 6.146203] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.146369] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.156126] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.178126] sda: sda1 sda2 < sda5 > [ 6.182559] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.218066] I/O error, dev mmcblk1, sector 7743835 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.326034] I/O error, dev mmcblk1, sector 7743836 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.434000] I/O error, dev mmcblk1, sector 7743837 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.542044] I/O error, dev mmcblk1, sector 7743838 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.650021] I/O error, dev mmcblk1, sector 7743839 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 7.058566] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.166161] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.230242] random: crng init done [ 7.339333] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.350288] device-mapper: uevent: version 1.0.3 [ 7.354919] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.774261] Buffer I/O error on dev mmcblk1, logical block 967979, async page read [ 11.203591] PM: Image not found (code -22) [ 11.770903] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 12.041791] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.360218] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.782994] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.793765] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.902714] panfrost 11800000.gpu: clock rate = 533000000 [ 15.939478] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 15.945794] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 15.953966] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 15.965709] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 15.982171] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 15.988335] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 16.154261] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 16.198274] usb3503 usb-hub: switched to HUB mode [ 16.201503] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 16.223662] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 16.332147] blk_print_req_error: 6 callbacks suppressed [ 16.332159] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.445435] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.522381] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.561561] I/O error, dev mmcblk1, sector 7743834 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.670010] I/O error, dev mmcblk1, sector 7743835 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.698830] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.705742] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.715762] hub 1-3:1.0: USB hub found [ 16.718265] hub 1-3:1.0: 3 ports detected [ 16.778333] I/O error, dev mmcblk1, sector 7743836 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.803385] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.886521] I/O error, dev mmcblk1, sector 7743837 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.994663] I/O error, dev mmcblk1, sector 7743838 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.026365] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 17.102835] I/O error, dev mmcblk1, sector 7743839 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 17.156344] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 17.163397] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 17.170844] usb 1-3.2: Product: USB2.0 Hub [ 17.183319] hub 1-3.2:1.0: USB hub found [ 17.186295] hub 1-3.2:1.0: 4 ports detected [ 17.490567] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.526752] I/O error, dev mmcblk1, sector 7743832 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.604782] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.612426] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.619723] usb 1-3.2.4: Product: AX88772 [ 17.623560] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.628752] usb 1-3.2.4: SerialNumber: 000001 [ 17.634727] I/O error, dev mmcblk1, sector 7743833 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 18.148102] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.244618] Buffer I/O error on dev mmcblk1, logical block 967979, async page read [ 18.817002] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.832554] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.846656] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, ea:da:de:7f:9a:a6 [ 18.861585] usbcore: registered new interface driver asix [ 19.756084] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 22.091163] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 22.153838] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 22.303040] Adding 1949692k swap on /dev/mapper/arndale--metrocentre--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 23.545919] audit: type=1400 audit(1726708526.028:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=896 comm="apparmor_parser" [ 23.562844] audit: type=1400 audit(1726708526.048:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=897 comm="apparmor_parser" [ 23.577392] audit: type=1400 audit(1726708526.048:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=897 comm="apparmor_parser" [ 23.770540] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 24.004156] audit: type=1400 audit(1726708526.488:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=939 comm="apparmor_parser" [ 24.019964] audit: type=1400 audit(1726708526.488:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=939 comm="apparmor_parser" [ 24.033492] audit: type=1400 audit(1726708526.492:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=939 comm="apparmor_parser" [ 24.348441] audit: type=1400 audit(1726708526.832:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=938 comm="apparmor_parser" [ 24.364998] audit: type=1400 audit(1726708526.832:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=938 comm="apparmor_parser" [ 24.382182] audit: type=1400 audit(1726708526.832:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=938 comm="apparmor_parser" [ 24.399707] audit: type=1400 audit(1726708526.832:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=938 comm="apparmor_parser" [ 25.928204] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.928318] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.900773] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.913303] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.922016] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.928424] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.937571] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.946880] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.953456] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.961994] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.968337] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.974994] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1