[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0+ (osstest@himrod2) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Sep 22 18:19:06 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.20 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41804 r8192 d23732 u73728 [ 0.000000] pcpu-alloc: s41804 r8192 d23732 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000012] Switching to timer-based delay loop, resolution 41ns [ 0.000518] Console: colour dummy device 80x30 [ 0.000535] printk: legacy console [hvc0] enabled [ 0.283743] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.294138] CPU: Testing write buffer coherency: ok [ 0.299078] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.308633] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.315045] pid_max: default: 32768 minimum: 301 [ 0.319855] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.327112] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.335535] /cpus/cpu@0 missing clock-frequency property [ 0.340340] /cpus/cpu@1 missing clock-frequency property [ 0.345710] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.352497] xen:grant_table: Grant tables using version 1 layout [ 0.357571] Grant table initialized [ 0.361110] xen:events: Using FIFO-based ABI [ 0.365418] Xen: initializing cpu0 [ 0.368943] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.376717] rcu: Hierarchical SRCU implementation. [ 0.380337] rcu: Max phase no-delay instances is 1000. [ 0.385852] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.396359] EFI services will not be available. [ 0.399682] smp: Bringing up secondary CPUs ... [ 0.474847] Xen: initializing cpu1 [ 0.475010] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.475035] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.494004] smp: Brought up 1 node, 2 CPUs [ 0.497664] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.503952] CPU: All CPU(s) started in SVC mode. [ 0.509284] Memory: 412716K/524288K available (15360K kernel code, 2289K rwdata, 6128K rodata, 2048K init, 441K bss, 44196K reserved, 65536K cma-reserved, 0K highmem) [ 0.524158] devtmpfs: initialized [ 0.537351] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.543885] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.553578] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.561488] pinctrl core: initialized pinctrl subsystem [ 0.568102] DMI not present or invalid. [ 0.571620] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.578256] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.587651] thermal_sys: Registered thermal governor 'step_wise' [ 0.587809] software IO TLB: area num 2. [ 0.596489] software IO TLB: only able to allocate 8 MB [ 0.603551] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.608741] No ATAGs? [ 0.611056] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.619667] Serial: AMBA PL011 UART driver [ 0.671156] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.699707] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.725658] xen:balloon: Initialising balloon driver [ 0.732117] iommu: Default domain type: Translated [ 0.735530] iommu: DMA domain TLB invalidation policy: strict mode [ 0.743187] SCSI subsystem initialized [ 0.745771] libata version 3.00 loaded. [ 0.745984] usbcore: registered new interface driver usbfs [ 0.751205] usbcore: registered new interface driver hub [ 0.756592] usbcore: registered new device driver usb [ 0.763196] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.766817] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.773031] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.778146] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.783033] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.789109] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.794842] pps_core: LinuxPPS API ver. 1 registered [ 0.799270] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.808465] PTP clock support registered [ 0.812642] EDAC MC: Ver: 3.0.0 [ 0.816030] scmi_core: SCMI protocol bus registered [ 0.829569] vgaarb: loaded [ 0.836359] clocksource: Switched to clocksource arch_sys_counter [ 0.851578] NET: Registered PF_INET protocol family [ 0.855215] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.863115] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.870832] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.878618] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.886462] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.893730] TCP: Hash tables configured (established 4096 bind 4096) [ 0.900098] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.906669] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.913769] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.919955] RPC: Registered named UNIX socket transport module. [ 0.925388] RPC: Registered udp transport module. [ 0.930184] RPC: Registered tcp transport module. [ 0.934936] RPC: Registered tcp-with-tls transport module. [ 0.940522] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.947031] PCI: CLS 0 bytes, default 64 [ 0.952113] Initialise system trusted keyrings [ 0.955887] Trying to unpack rootfs image as initramfs... [ 0.986505] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.991858] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.008906] NFS: Registering the id_resolver key type [ 1.012622] Key type id_resolver registered [ 1.016870] Key type id_legacy registered [ 1.020964] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.027733] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.067538] Key type asymmetric registered [ 1.070269] Asymmetric key parser 'x509' registered [ 1.075271] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.082695] io scheduler mq-deadline registered [ 1.087302] io scheduler kyber registered [ 1.091396] io scheduler bfq registered [ 1.208085] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.214301] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.247545] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.253747] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.281544] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.287785] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.318317] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.324546] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.336920] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.402190] xen:xen_evtchn: Event-channel device installed [ 1.584949] Freeing initrd memory: 11884K [ 1.630875] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.670745] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.678973] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.687859] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.696847] SuperH (H)SCI(F) driver initialized [ 1.701185] STMicroelectronics ASC driver initialized [ 1.706010] STM32 USART driver initialized [ 1.711547] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.720361] random: crng init done [ 1.728664] brd: module loaded [ 1.734593] loop: module loaded [ 1.768036] Invalid max_queues (4), will use default max: 2. [ 1.787119] tun: Universal TUN/TAP device driver, 1.6 [ 1.791002] CAN device driver interface [ 1.796098] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.807422] xen_netfront: Initialising Xen virtual ethernet driver [ 1.812277] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.817911] usbcore: registered new interface driver pegasus [ 1.823622] usbcore: registered new interface driver asix [ 1.829112] usbcore: registered new interface driver ax88179_178a [ 1.835257] usbcore: registered new interface driver cdc_ether [ 1.841206] usbcore: registered new interface driver smsc75xx [ 1.847022] usbcore: registered new interface driver smsc95xx [ 1.852787] usbcore: registered new interface driver net1080 [ 1.858533] usbcore: registered new interface driver cdc_subset [ 1.864503] usbcore: registered new interface driver zaurus [ 1.870165] usbcore: registered new interface driver cdc_ncm [ 1.879738] usbcore: registered new interface driver usb-storage [ 1.890594] i2c_dev: i2c /dev entries driver [ 1.909293] device-mapper: uevent: version 1.0.3 [ 1.912714] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.922387] cpu cpu0: OPP table can't be empty [ 1.927091] failed to register cpuidle driver [ 1.930422] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.938824] sdhci: Secure Digital Host Controller Interface driver [ 1.943788] sdhci: Copyright(c) Pierre Ossman [ 1.951895] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.959735] ledtrig-cpu: registered to indicate activity on CPUs [ 1.965439] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.972030] usbcore: registered new interface driver usbhid [ 1.976557] usbhid: USB HID core driver [ 1.987925] NET: Registered PF_INET6 protocol family [ 1.992527] Segment Routing with IPv6 [ 1.995277] In-situ OAM (IOAM) with IPv6 [ 1.999373] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.005711] NET: Registered PF_PACKET protocol family [ 2.010384] can: controller area network core [ 2.014814] NET: Registered PF_CAN protocol family [ 2.019664] can: raw protocol [ 2.022684] can: broadcast manager protocol [ 2.026988] can: netlink gateway - max_hops=1 [ 2.031717] Key type dns_resolver registered [ 2.036484] ThumbEE CPU extension supported. [ 2.040053] Registering SWP/SWPB emulation handler [ 2.054733] Loading compiled-in X.509 certificates [ 2.095400] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.099080] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.105654] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.113807] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.155338] s5m-rtc s5m-rtc: registered as rtc0 [ 2.164230] s5m-rtc s5m-rtc: setting system clock to 2024-09-22T21:58:44 UTC (1727042324) [ 2.175329] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.179998] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.184304] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.191109] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.197035] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.203203] clk: Not disabling unused clocks [ 2.206757] PM: genpd: Disabling unused power domains [ 2.215266] Freeing unused kernel image (initmem) memory: 2048K [ 2.221578] Run /init as init process [ 2.223866] with arguments: [ 2.223873] /init [ 2.223879] with environment: [ 2.223885] HOME=/ [ 2.223891] TERM=linux [ 3.407014] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.561523] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.582282] phy phy-12130000.phy.5: phy_power_on was called before phy_init [ 3.587943] exynos-ohci 12120000.usb: USB Host Controller [ 3.593369] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 3.603217] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.609437] phy phy-12130000.phy.5: phy_power_on was called before phy_init [ 3.615038] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.620654] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 3.674947] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.697346] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.720469] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.737275] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.745247] Synopsys Designware Multimedia Card Interface Driver [ 3.789958] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.790132] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.796296] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.810560] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.814773] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.820170] hub 1-0:1.0: USB hub found [ 3.828936] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.835227] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.840819] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.850338] hub 1-0:1.0: 3 ports detected [ 3.856076] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.861210] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.866756] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.878186] hub 2-0:1.0: USB hub found [ 3.881193] hub 2-0:1.0: 3 ports detected [ 3.898858] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.913356] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.915633] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.919090] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.937780] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.944412] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 4.008526] mmc_host mmc0: card is polling. [ 4.032641] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.046490] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.087747] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.091950] scsi host0: ahci-dwc [ 4.095065] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 4.191923] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.211799] mmc0: new DDR MMC card at address 0001 [ 4.219508] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.229523] mmcblk0: p1 p2 p3 p4 [ 4.237324] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.246113] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.250880] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.264833] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.266475] mmc1: new high speed SDHC card at address aaaa [ 4.283135] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.586415] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.592228] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.598042] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.605768] ata1.00: configured for UDMA/133 [ 4.609392] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.618869] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.625031] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.630422] sd 0:0:0:0: [sda] Write Protect is off [ 4.635167] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.635301] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.644550] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.717208] sda: sda1 sda2 < sda5 > [ 4.720317] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.782199] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.794569] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.798750] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.809470] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000808002000010 [ 4.818670] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.823833] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.830167] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.837285] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.867835] hub 3-0:1.0: USB hub found [ 4.886803] hub 3-0:1.0: 1 port detected [ 4.903287] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.921883] hub 4-0:1.0: USB hub found [ 4.924307] hub 4-0:1.0: 1 port detected [ 9.069904] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 9.398797] EXT4-fs (dm-0): mounted filesystem 7fd2f58e-ca1a-48d3-8476-cd9a30675ddb ro with ordered data mode. Quota mode: disabled. [ 13.230154] s5p-secss 10830000.sss: s5p-sss driver registered [ 13.246390] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 13.278236] mc: Linux media interface: v0.10 [ 13.398435] videodev: Linux video capture interface: v2.00 [ 13.676839] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 13.724396] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 13.733187] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 13.739221] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 13.745495] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 13.751310] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 13.751503] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 13.779652] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 13.787030] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 13.798789] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 13.804273] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 14.061387] usb3503 usb-hub: switched to HUB mode [ 14.065097] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 14.376467] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 14.529008] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 14.570915] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.583502] hub 2-3:1.0: USB hub found [ 14.591548] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 14.602827] hub 2-3:1.0: 3 ports detected [ 14.708265] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.715908] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.724703] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.735533] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.744324] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.753024] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.966389] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 15.109991] hub 2-3.2:1.0: USB hub found [ 15.112979] hub 2-3.2:1.0: 4 ports detected [ 15.189438] usbcore: registered new device driver onboard-usb-dev [ 15.426456] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 15.550755] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 15.859378] EXT4-fs (dm-0): re-mounted 7fd2f58e-ca1a-48d3-8476-cd9a30675ddb r/w. Quota mode: disabled. [ 16.243897] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 16.265230] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 16.275234] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 5e:87:7f:7d:5a:61 [ 17.692088] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 18.109983] EXT4-fs (sda1): mounted filesystem 9ebb4149-3a41-44bb-b990-79f7941a401b r/w with ordered data mode. Quota mode: disabled. [ 18.206424] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 20.049913] xenbr0: port 1(eth0) entered blocking state [ 20.053777] xenbr0: port 1(eth0) entered disabled state [ 20.059125] asix 2-3.2.4:1.0 eth0: entered allmulticast mode [ 20.064942] asix 2-3.2.4:1.0 eth0: entered promiscuous mode [ 20.075472] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 22.253735] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 22.256552] xenbr0: port 1(eth0) entered blocking state [ 22.264999] xenbr0: port 1(eth0) entered forwarding state