[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0+ (osstest@himrod2) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Sep 22 18:19:06 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.20 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41804 r8192 d23732 u73728 [ 0.000000] pcpu-alloc: s41804 r8192 d23732 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000011] Switching to timer-based delay loop, resolution 41ns [ 0.000518] Console: colour dummy device 80x30 [ 0.000536] printk: legacy console [hvc0] enabled [ 0.283741] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.294134] CPU: Testing write buffer coherency: ok [ 0.299075] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.308629] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.315042] pid_max: default: 32768 minimum: 301 [ 0.319834] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.327109] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.335528] /cpus/cpu@0 missing clock-frequency property [ 0.340338] /cpus/cpu@1 missing clock-frequency property [ 0.345708] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.352492] xen:grant_table: Grant tables using version 1 layout [ 0.357564] Grant table initialized [ 0.361111] xen:events: Using FIFO-based ABI [ 0.365414] Xen: initializing cpu0 [ 0.368940] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.376720] rcu: Hierarchical SRCU implementation. [ 0.380334] rcu: Max phase no-delay instances is 1000. [ 0.385851] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.396360] EFI services will not be available. [ 0.399678] smp: Bringing up secondary CPUs ... [ 0.474740] Xen: initializing cpu1 [ 0.474905] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.474930] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.493901] smp: Brought up 1 node, 2 CPUs [ 0.497556] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.503844] CPU: All CPU(s) started in SVC mode. [ 0.509183] Memory: 412716K/524288K available (15360K kernel code, 2289K rwdata, 6128K rodata, 2048K init, 441K bss, 44196K reserved, 65536K cma-reserved, 0K highmem) [ 0.524057] devtmpfs: initialized [ 0.537220] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.543750] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.553444] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.561336] pinctrl core: initialized pinctrl subsystem [ 0.567984] DMI not present or invalid. [ 0.571505] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.578148] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.587544] thermal_sys: Registered thermal governor 'step_wise' [ 0.587702] software IO TLB: area num 2. [ 0.596383] software IO TLB: only able to allocate 8 MB [ 0.603447] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.608641] No ATAGs? [ 0.610955] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.619564] Serial: AMBA PL011 UART driver [ 0.671057] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.699595] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.725515] xen:balloon: Initialising balloon driver [ 0.731983] iommu: Default domain type: Translated [ 0.735396] iommu: DMA domain TLB invalidation policy: strict mode [ 0.743111] SCSI subsystem initialized [ 0.745655] libata version 3.00 loaded. [ 0.745870] usbcore: registered new interface driver usbfs [ 0.751090] usbcore: registered new interface driver hub [ 0.756476] usbcore: registered new device driver usb [ 0.763073] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.766693] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.772907] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.778023] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.782910] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.788985] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.794714] pps_core: LinuxPPS API ver. 1 registered [ 0.799147] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.808339] PTP clock support registered [ 0.812519] EDAC MC: Ver: 3.0.0 [ 0.815906] scmi_core: SCMI protocol bus registered [ 0.829585] vgaarb: loaded [ 0.836364] clocksource: Switched to clocksource arch_sys_counter [ 0.851590] NET: Registered PF_INET protocol family [ 0.855231] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.863131] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.870846] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.878632] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.886476] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.893745] TCP: Hash tables configured (established 4096 bind 4096) [ 0.900129] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.906683] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.913785] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.919967] RPC: Registered named UNIX socket transport module. [ 0.925403] RPC: Registered udp transport module. [ 0.930215] RPC: Registered tcp transport module. [ 0.934949] RPC: Registered tcp-with-tls transport module. [ 0.940536] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.947043] PCI: CLS 0 bytes, default 64 [ 0.952134] Initialise system trusted keyrings [ 0.955924] Trying to unpack rootfs image as initramfs... [ 0.986522] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.991871] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.011134] NFS: Registering the id_resolver key type [ 1.014841] Key type id_resolver registered [ 1.019094] Key type id_legacy registered [ 1.023173] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.029961] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.078334] Key type asymmetric registered [ 1.081093] Asymmetric key parser 'x509' registered [ 1.086073] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.093498] io scheduler mq-deadline registered [ 1.098107] io scheduler kyber registered [ 1.102182] io scheduler bfq registered [ 1.221975] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.228197] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.258109] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.264336] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.297103] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.303306] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.353327] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.359620] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.372352] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.455796] xen:xen_evtchn: Event-channel device installed [ 1.567661] Freeing initrd memory: 11884K [ 1.630081] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.641068] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.649249] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.658158] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.667136] SuperH (H)SCI(F) driver initialized [ 1.671470] STMicroelectronics ASC driver initialized [ 1.676364] STM32 USART driver initialized [ 1.681814] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.688927] random: crng init done [ 1.700450] brd: module loaded [ 1.706398] loop: module loaded [ 1.757479] Invalid max_queues (4), will use default max: 2. [ 1.776515] tun: Universal TUN/TAP device driver, 1.6 [ 1.780389] CAN device driver interface [ 1.785481] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.796792] xen_netfront: Initialising Xen virtual ethernet driver [ 1.801651] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.807288] usbcore: registered new interface driver pegasus [ 1.812995] usbcore: registered new interface driver asix [ 1.818517] usbcore: registered new interface driver ax88179_178a [ 1.824643] usbcore: registered new interface driver cdc_ether [ 1.830559] usbcore: registered new interface driver smsc75xx [ 1.836365] usbcore: registered new interface driver smsc95xx [ 1.842158] usbcore: registered new interface driver net1080 [ 1.847937] usbcore: registered new interface driver cdc_subset [ 1.853883] usbcore: registered new interface driver zaurus [ 1.859537] usbcore: registered new interface driver cdc_ncm [ 1.869102] usbcore: registered new interface driver usb-storage [ 1.879829] i2c_dev: i2c /dev entries driver [ 1.898371] device-mapper: uevent: version 1.0.3 [ 1.901792] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.911425] cpu cpu0: OPP table can't be empty [ 1.916122] failed to register cpuidle driver [ 1.919525] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.927886] sdhci: Secure Digital Host Controller Interface driver [ 1.932865] sdhci: Copyright(c) Pierre Ossman [ 1.940971] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.948805] ledtrig-cpu: registered to indicate activity on CPUs [ 1.954490] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.961019] usbcore: registered new interface driver usbhid [ 1.965588] usbhid: USB HID core driver [ 1.976949] NET: Registered PF_INET6 protocol family [ 1.981538] Segment Routing with IPv6 [ 1.984310] In-situ OAM (IOAM) with IPv6 [ 1.988374] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.994714] NET: Registered PF_PACKET protocol family [ 1.999420] can: controller area network core [ 2.003842] NET: Registered PF_CAN protocol family [ 2.008691] can: raw protocol [ 2.011709] can: broadcast manager protocol [ 2.015965] can: netlink gateway - max_hops=1 [ 2.020749] Key type dns_resolver registered [ 2.025399] ThumbEE CPU extension supported. [ 2.029120] Registering SWP/SWPB emulation handler [ 2.043726] Loading compiled-in X.509 certificates [ 2.084298] s3c-i2c 12c60000.i2c: slave address 0x66 [ 2.087980] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 2.094717] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 2.102708] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.144298] s5m-rtc s5m-rtc: registered as rtc0 [ 2.153207] s5m-rtc s5m-rtc: setting system clock to 2024-09-22T21:02:16 UTC (1727038936) [ 2.164311] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.168989] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.173286] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.180115] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.185880] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.192146] clk: Not disabling unused clocks [ 2.195592] PM: genpd: Disabling unused power domains [ 2.204410] Freeing unused kernel image (initmem) memory: 2048K [ 2.210724] Run /init as init process [ 2.213011] with arguments: [ 2.213018] /init [ 2.213025] with environment: [ 2.213030] HOME=/ [ 2.213036] TERM=linux [ 3.472062] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.549891] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.557033] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.580415] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.598565] Synopsys Designware Multimedia Card Interface Driver [ 3.648121] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.663522] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.688577] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.693666] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.699218] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 125,32 bit host data width,128 deep fifo [ 3.708941] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.715190] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.720750] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.766545] mmc_host mmc0: card is polling. [ 3.786183] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.789487] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.791836] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.807506] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.817222] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.856310] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.907355] exynos-ehci 12110000.usb: irq 127, io mem 0x12110000 [ 3.926837] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.967896] hub 1-0:1.0: USB hub found [ 3.974339] hub 1-0:1.0: 3 ports detected [ 3.983404] phy phy-12130000.phy.9: phy_power_on was called before phy_init [ 3.989063] exynos-ohci 12120000.usb: USB Host Controller [ 3.994532] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 4.046017] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.054886] mmc1: new high speed SDHC card at address aaaa [ 4.061341] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.063438] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.144080] exynos-ohci 12120000.usb: irq 127, io mem 0x12120000 [ 4.149047] mmc0: new DDR MMC card at address 0001 [ 4.169982] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.187872] mmcblk0: p1 p2 p3 p4 [ 4.198490] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.213723] hub 2-0:1.0: USB hub found [ 4.215049] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.216208] hub 2-0:1.0: 3 ports detected [ 4.237625] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.241243] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 4.256977] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 4.265866] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 4.280315] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 4.286024] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 4.294922] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 4.301771] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 4.318554] scsi host0: ahci-dwc [ 4.321092] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 4.343878] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 4.350653] s3c-rtc 101e0000.rtc: registered as rtc1 [ 4.806463] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.812302] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.818097] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.825817] ata1.00: configured for UDMA/133 [ 4.829384] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.838770] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.844900] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.850303] sd 0:0:0:0: [sda] Write Protect is off [ 4.855042] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.855118] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.864346] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.975213] sda: sda1 sda2 < sda5 > [ 4.977975] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.997405] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 5.004719] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.009058] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.042324] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000808002000010 [ 5.050609] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 5.056647] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.061989] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.069748] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.077447] hub 3-0:1.0: USB hub found [ 5.080404] hub 3-0:1.0: 1 port detected [ 5.085186] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.093299] hub 4-0:1.0: USB hub found [ 5.096360] hub 4-0:1.0: 1 port detected [ 9.367259] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 9.534526] EXT4-fs (dm-0): mounted filesystem 5c1e3af1-361d-4e2e-8585-f3d12c1675e4 ro with ordered data mode. Quota mode: disabled. [ 13.438169] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 13.461067] s5p-secss 10830000.sss: s5p-sss driver registered [ 13.469765] mc: Linux media interface: v0.10 [ 13.586830] videodev: Linux video capture interface: v2.00 [ 13.897517] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 13.958978] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 13.991658] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 14.005481] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 14.016772] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 14.027774] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 14.061478] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.096518] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.103870] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.135578] s5p-mfc 11000000.codec: decoder registered as /dev/video4 [ 14.143520] s5p-mfc 11000000.codec: encoder registered as /dev/video5 [ 14.166431] usb3503 usb-hub: switched to HUB mode [ 14.169784] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 14.487373] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 14.616907] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 14.651367] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.670426] hub 1-3:1.0: USB hub found [ 14.678662] hub 1-3:1.0: 3 ports detected [ 14.694993] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 14.936638] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.944456] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.953105] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.967053] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.974756] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.983494] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 15.026412] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 15.170070] hub 1-3.2:1.0: USB hub found [ 15.173114] hub 1-3.2:1.0: 4 ports detected [ 15.264461] usbcore: registered new device driver onboard-usb-dev [ 15.476426] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 15.600233] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 16.248355] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 16.262849] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 16.272746] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 42:71:db:01:51:24 [ 16.973222] EXT4-fs (dm-0): re-mounted 5c1e3af1-361d-4e2e-8585-f3d12c1675e4 r/w. Quota mode: disabled. [ 18.971566] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 19.012239] EXT4-fs (sda1): mounted filesystem 5be45eea-b21a-4841-af63-4bdb5e521954 r/w with ordered data mode. Quota mode: disabled. [ 19.119877] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 20.942825] xenbr0: port 1(eth0) entered blocking state [ 20.946721] xenbr0: port 1(eth0) entered disabled state [ 20.951998] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 20.957881] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 20.968760] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.218407] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 23.224429] xenbr0: port 1(eth0) entered blocking state [ 23.229662] xenbr0: port 1(eth0) entered forwarding state [ 25.611145] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed