[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.11.0+ (osstest@himrod1) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Mon Sep 23 06:34:19 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Xen 4.20 support found [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 on node -1 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000007fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s41804 r8192 d23732 u73728 [ 0.000000] pcpu-alloc: s41804 r8192 d23732 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=hvc0 clk_ignore_unused clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000012] Switching to timer-based delay loop, resolution 41ns [ 0.000514] Console: colour dummy device 80x30 [ 0.000531] printk: legacy console [hvc0] enabled [ 0.283741] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.294134] CPU: Testing write buffer coherency: ok [ 0.299095] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.308629] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.315043] pid_max: default: 32768 minimum: 301 [ 0.319836] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.327109] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.335534] /cpus/cpu@0 missing clock-frequency property [ 0.340313] /cpus/cpu@1 missing clock-frequency property [ 0.345710] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.352497] xen:grant_table: Grant tables using version 1 layout [ 0.357565] Grant table initialized [ 0.361109] xen:events: Using FIFO-based ABI [ 0.365417] Xen: initializing cpu0 [ 0.368940] Setting up static identity map for 0x60300000 - 0x603000ac [ 0.376717] rcu: Hierarchical SRCU implementation. [ 0.380335] rcu: Max phase no-delay instances is 1000. [ 0.385850] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.396352] EFI services will not be available. [ 0.399649] smp: Bringing up secondary CPUs ... [ 0.474767] Xen: initializing cpu1 [ 0.474929] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.474953] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.493921] smp: Brought up 1 node, 2 CPUs [ 0.497583] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.503871] CPU: All CPU(s) started in SVC mode. [ 0.509209] Memory: 412716K/524288K available (15360K kernel code, 2289K rwdata, 6128K rodata, 2048K init, 441K bss, 44196K reserved, 65536K cma-reserved, 0K highmem) [ 0.524078] devtmpfs: initialized [ 0.537258] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.543789] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.553479] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.561361] pinctrl core: initialized pinctrl subsystem [ 0.568039] DMI not present or invalid. [ 0.571564] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.578209] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.587611] thermal_sys: Registered thermal governor 'step_wise' [ 0.587770] software IO TLB: area num 2. [ 0.596450] software IO TLB: only able to allocate 8 MB [ 0.603513] software IO TLB: mapped [mem 0x63000000-0x63800000] (8MB) [ 0.608703] No ATAGs? [ 0.611016] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 0.619630] Serial: AMBA PL011 UART driver [ 0.671062] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 65 [ 0.699609] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.725117] xen:balloon: Initialising balloon driver [ 0.731591] iommu: Default domain type: Translated [ 0.735007] iommu: DMA domain TLB invalidation policy: strict mode [ 0.742562] SCSI subsystem initialized [ 0.745245] libata version 3.00 loaded. [ 0.745455] usbcore: registered new interface driver usbfs [ 0.750688] usbcore: registered new interface driver hub [ 0.756063] usbcore: registered new device driver usb [ 0.762659] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.766272] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.772496] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.777612] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.782492] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.788564] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.794295] pps_core: LinuxPPS API ver. 1 registered [ 0.798726] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.807924] PTP clock support registered [ 0.812101] EDAC MC: Ver: 3.0.0 [ 0.815488] scmi_core: SCMI protocol bus registered [ 0.829581] vgaarb: loaded [ 0.836362] clocksource: Switched to clocksource arch_sys_counter [ 0.851571] NET: Registered PF_INET protocol family [ 0.855215] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.863115] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.870829] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.878615] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.886460] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.893727] TCP: Hash tables configured (established 4096 bind 4096) [ 0.900119] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.906667] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.913767] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.919951] RPC: Registered named UNIX socket transport module. [ 0.925386] RPC: Registered udp transport module. [ 0.930199] RPC: Registered tcp transport module. [ 0.934933] RPC: Registered tcp-with-tls transport module. [ 0.940518] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.947028] PCI: CLS 0 bytes, default 64 [ 0.952105] Initialise system trusted keyrings [ 0.955885] Trying to unpack rootfs image as initramfs... [ 0.986500] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.991857] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.008913] NFS: Registering the id_resolver key type [ 1.012622] Key type id_resolver registered [ 1.016877] Key type id_legacy registered [ 1.020971] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.027738] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.067489] Key type asymmetric registered [ 1.070243] Asymmetric key parser 'x509' registered [ 1.075223] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 1.082655] io scheduler mq-deadline registered [ 1.087252] io scheduler kyber registered [ 1.091353] io scheduler bfq registered [ 1.211890] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.218141] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.243012] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.249263] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.277874] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.284111] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.308380] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.314581] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.327009] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.370802] xen:xen_evtchn: Event-channel device installed [ 1.483992] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.494972] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.503167] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.512287] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 1.521247] SuperH (H)SCI(F) driver initialized [ 1.525393] STMicroelectronics ASC driver initialized [ 1.530417] STM32 USART driver initialized [ 1.536004] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 1.543171] random: crng init done [ 1.559895] brd: module loaded [ 1.566785] loop: module loaded [ 1.582904] Invalid max_queues (4), will use default max: 2. [ 1.603444] tun: Universal TUN/TAP device driver, 1.6 [ 1.607342] CAN device driver interface [ 1.612443] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 1.624881] xen_netfront: Initialising Xen virtual ethernet driver [ 1.629781] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 1.635361] usbcore: registered new interface driver pegasus [ 1.641141] usbcore: registered new interface driver asix [ 1.646599] usbcore: registered new interface driver ax88179_178a [ 1.652723] usbcore: registered new interface driver cdc_ether [ 1.658670] usbcore: registered new interface driver smsc75xx [ 1.664457] usbcore: registered new interface driver smsc95xx [ 1.670298] usbcore: registered new interface driver net1080 [ 1.675980] usbcore: registered new interface driver cdc_subset [ 1.681984] usbcore: registered new interface driver zaurus [ 1.687630] usbcore: registered new interface driver cdc_ncm [ 1.697203] usbcore: registered new interface driver usb-storage [ 1.708210] i2c_dev: i2c /dev entries driver [ 1.733847] device-mapper: uevent: version 1.0.3 [ 1.737345] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@lists.linux.dev [ 1.747001] cpu cpu0: OPP table can't be empty [ 1.749079] Freeing initrd memory: 11884K [ 1.752147] failed to register cpuidle driver [ 1.759102] exynos_cpuidle exynos_cpuidle: failed to register cpuidle driver [ 1.767476] sdhci: Secure Digital Host Controller Interface driver [ 1.772432] sdhci: Copyright(c) Pierre Ossman [ 1.780519] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.799884] ledtrig-cpu: registered to indicate activity on CPUs [ 1.805601] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.821942] usbcore: registered new interface driver usbhid [ 1.826135] usbhid: USB HID core driver [ 1.837846] NET: Registered PF_INET6 protocol family [ 1.842258] Segment Routing with IPv6 [ 1.845196] In-situ OAM (IOAM) with IPv6 [ 1.849255] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.855611] NET: Registered PF_PACKET protocol family [ 1.860324] can: controller area network core [ 1.864734] NET: Registered PF_CAN protocol family [ 1.869585] can: raw protocol [ 1.872603] can: broadcast manager protocol [ 1.876875] can: netlink gateway - max_hops=1 [ 1.881600] Key type dns_resolver registered [ 1.886967] ThumbEE CPU extension supported. [ 1.889968] Registering SWP/SWPB emulation handler [ 1.904548] Loading compiled-in X.509 certificates [ 1.944762] s3c-i2c 12c60000.i2c: slave address 0x66 [ 1.948391] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 1.954917] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 1.963151] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 2.003852] s5m-rtc s5m-rtc: registered as rtc0 [ 2.012600] s5m-rtc s5m-rtc: setting system clock to 2024-09-23T07:42:30 UTC (1727077350) [ 2.023777] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 2.028479] s3c-i2c 12c90000.i2c: slave address 0x00 [ 2.032758] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 2.039618] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 2.045439] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.051707] clk: Not disabling unused clocks [ 2.055108] PM: genpd: Disabling unused power domains [ 2.063752] Freeing unused kernel image (initmem) memory: 2048K [ 2.070101] Run /init as init process [ 2.072403] with arguments: [ 2.072409] /init [ 2.072415] with environment: [ 2.072421] HOME=/ [ 2.072427] TERM=linux [ 3.259197] i2c-gpio i2c-10: using lines 552 (SDA) and 553 (SCL) [ 3.411744] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 3.419005] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 3.455459] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 3.500146] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.505777] exynos-ehci 12110000.usb: EHCI Host Controller [ 3.511379] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 3.529430] exynos-ehci 12110000.usb: irq 125, io mem 0x12110000 [ 3.573029] Synopsys Designware Multimedia Card Interface Driver [ 3.581239] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.590038] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 3.596230] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 3.603660] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 3.611404] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 3.618740] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.623842] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 3.629422] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 126,32 bit host data width,128 deep fifo [ 3.639522] mmc_host mmc0: card is polling. [ 3.643839] hub 1-0:1.0: USB hub found [ 3.672949] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.679582] hub 1-0:1.0: 3 ports detected [ 3.686134] phy phy-12130000.phy.8: phy_power_on was called before phy_init [ 3.691783] exynos-ohci 12120000.usb: USB Host Controller [ 3.704238] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.709392] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 3.714865] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 127,32 bit host data width,128 deep fifo [ 3.720873] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 3.731696] ahci-dwc 122f0000.sata: AHCI vers 0001.0300, 32 command slots, 6 Gbps, platform mode [ 3.740327] ahci-dwc 122f0000.sata: 1/1 ports implemented (port mask 0x1) [ 3.740347] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.747188] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.756774] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 3.778442] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 3.821830] s2mps11-clk s5m8767-clk: DMA mask not set [ 3.835386] exynos-ohci 12120000.usb: irq 125, io mem 0x12120000 [ 3.874659] scsi host0: ahci-dwc [ 3.876883] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 128 lpm-pol 0 [ 3.916116] hub 2-0:1.0: USB hub found [ 3.926801] hub 2-0:1.0: 3 ports detected [ 3.950352] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 3.961920] s3c-rtc 101e0000.rtc: registered as rtc1 [ 3.991893] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 4.005763] mmc0: new DDR MMC card at address 0001 [ 4.010350] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 4.023178] mmcblk0: p1 p2 p3 p4 [ 4.031482] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 4.044290] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 4.057945] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (238:0) [ 4.063485] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.073534] mmc1: new high speed SDHC card at address aaaa [ 4.084881] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 4.366408] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.374629] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 4.379991] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 4.388465] ata1.00: configured for UDMA/133 [ 4.391697] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 4.401887] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.408043] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.415603] sd 0:0:0:0: [sda] Write Protect is off [ 4.419083] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.419911] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.432177] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.546050] sda: sda1 sda2 < sda5 > [ 4.548882] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.586059] dwc3 12000000.usb: Configuration mismatch. dr_mode forced to host [ 4.607822] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.612129] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 4.731099] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000808002000010 [ 4.739351] xhci-hcd xhci-hcd.2.auto: irq 130, io mem 0x12000000 [ 4.745428] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.750818] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 4.758530] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 4.766035] hub 3-0:1.0: USB hub found [ 4.768981] hub 3-0:1.0: 1 port detected [ 4.773677] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.781869] hub 4-0:1.0: USB hub found [ 4.784906] hub 4-0:1.0: 1 port detected [ 8.904870] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 9.249747] EXT4-fs (dm-0): mounted filesystem 4f18f9b2-4264-477e-9da2-4f54eb6c11c0 ro with ordered data mode. Quota mode: disabled. [ 13.064066] s5p-secss 10830000.sss: s5p-sss driver registered [ 13.109809] mc: Linux media interface: v0.10 [ 13.113261] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 13.251427] videodev: Linux video capture interface: v2.00 [ 13.354564] s5p-mfc 11000000.codec: Adding to iommu group 0 [ 13.483397] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers [ 13.520789] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 13.561996] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 13.569425] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 13.598425] s5p-mfc 11000000.codec: decoder registered as /dev/video0 [ 13.604229] s5p-mfc 11000000.codec: encoder registered as /dev/video1 [ 13.697465] exynos-gsc 13e00000.gsc: Adding to iommu group 1 [ 13.716236] exynos-gsc 13e10000.gsc: Adding to iommu group 2 [ 13.729969] exynos-gsc 13e20000.gsc: Adding to iommu group 3 [ 13.737400] exynos-gsc 13e30000.gsc: Adding to iommu group 4 [ 13.836439] usb3503 usb-hub: switched to HUB mode [ 13.839843] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 14.157305] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 14.343112] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s [ 14.358418] hub 1-3:1.0: USB hub found [ 14.362197] hub 1-3:1.0: 3 ports detected [ 14.365546] wm8994 3-001a: Device is not a WM8994, ID is 0 [ 14.383528] wm8994 3-001a: probe with driver wm8994 failed with error -22 [ 14.591260] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.599009] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.607706] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.618527] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2 [ 14.627292] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2 [ 14.635970] s5p_mfc_load_firmware:75: Firmware is not present in the /lib/firmware directory nor compiled in kernel [ 14.726537] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 14.849043] hub 1-3.2:1.0: USB hub found [ 14.855796] hub 1-3.2:1.0: 4 ports detected [ 14.951950] usbcore: registered new device driver onboard-usb-dev [ 15.166411] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 15.297682] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 15.643654] EXT4-fs (dm-0): re-mounted 4f18f9b2-4264-477e-9da2-4f54eb6c11c0 r/w. Quota mode: disabled. [ 15.968408] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 15.982908] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 15.992917] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 7e:7f:4c:3e:bf:5c [ 17.308953] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.360731] EXT4-fs (sda1): mounted filesystem 87b2c927-204b-4347-bc58-27c3cf602890 r/w with ordered data mode. Quota mode: disabled. [ 17.457279] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k [ 19.301417] xenbr0: port 1(eth0) entered blocking state [ 19.305281] xenbr0: port 1(eth0) entered disabled state [ 19.310651] asix 1-3.2.4:1.0 eth0: entered allmulticast mode [ 19.316486] asix 1-3.2.4:1.0 eth0: entered promiscuous mode [ 19.327314] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 21.535327] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 21.536526] xenbr0: port 1(eth0) entered blocking state [ 21.546612] xenbr0: port 1(eth0) entered forwarding state [ 22.536477] xenbr0: port 1(eth0) entered disabled state [ 24.968212] platform sound: deferred probe pending: arndale-audio: snd_soc_register_card() failed [ 26.814034] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 26.820050] xenbr0: port 1(eth0) entered blocking state [ 26.825267] xenbr0: port 1(eth0) entered forwarding state [ 28.183484] xenbr0: port 1(eth0) entered disabled state