[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-25-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.106-3 (2024-08-26) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44820 r8192 d20716 u73728 [ 0.000000] pcpu-alloc: s44820 r8192 d20716 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--westfield--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015504K/2097152K available (12288K kernel code, 1717K rwdata, 3748K rodata, 2048K init, 383K bss, 65264K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39996 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000018] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002624] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002638] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002653] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002664] Ignoring duplicate/late registration of read_current_timer delay [ 0.003032] Console: colour dummy device 80x30 [ 0.003073] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003086] CPU: Testing write buffer coherency: ok [ 0.003128] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003137] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003143] pid_max: default: 32768 minimum: 301 [ 0.003511] LSM: Security Framework initializing [ 0.003583] landlock: Up and running. [ 0.003588] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003776] AppArmor: AppArmor initialized [ 0.003788] TOMOYO Linux initialized [ 0.003833] LSM support for eBPF active [ 0.004080] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004094] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005511] /cpus/cpu@0 missing clock-frequency property [ 0.005537] /cpus/cpu@1 missing clock-frequency property [ 0.005550] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006503] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006510] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006612] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006617] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006758] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007917] rcu: Hierarchical SRCU implementation. [ 0.007923] rcu: Max phase no-delay instances is 1000. [ 0.010061] EFI services will not be available. [ 0.010404] smp: Bringing up secondary CPUs ... [ 0.011143] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011154] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011285] smp: Brought up 1 node, 2 CPUs [ 0.011295] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011302] CPU: All CPU(s) started in HYP mode. [ 0.011306] CPU: Virtualization extensions available. [ 0.012168] devtmpfs: initialized [ 0.023171] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023400] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023424] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.023957] pinctrl core: initialized pinctrl subsystem [ 0.024711] DMI not present or invalid. [ 0.025390] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.026941] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028461] audit: initializing netlink subsys (disabled) [ 0.028664] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.029850] thermal_sys: Registered thermal governor 'fair_share' [ 0.029858] thermal_sys: Registered thermal governor 'bang_bang' [ 0.029862] thermal_sys: Registered thermal governor 'step_wise' [ 0.029867] thermal_sys: Registered thermal governor 'user_space' [ 0.029872] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030071] No ATAGs? [ 0.030137] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030145] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031229] Serial: AMBA PL011 UART driver [ 0.080585] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.087537] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091740] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091748] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.099297] iommu: Default domain type: Translated [ 0.099305] iommu: DMA domain TLB invalidation policy: strict mode [ 0.100283] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100794] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100805] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.101318] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.101348] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101592] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.102084] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.102095] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.102472] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102764] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102774] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.103069] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.103198] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.103207] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.103389] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103604] pps_core: LinuxPPS API ver. 1 registered [ 0.103609] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103626] PTP clock support registered [ 0.105119] NetLabel: Initializing [ 0.105124] NetLabel: domain hash size = 128 [ 0.105130] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.105184] NetLabel: unlabeled traffic allowed by default [ 0.105355] vgaarb: loaded [ 0.106259] clocksource: Switched to clocksource mct-frc [ 0.106836] VFS: Disk quotas dquot_6.6.0 [ 0.106919] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107742] AppArmor: AppArmor Filesystem Enabled [ 0.117572] NET: Registered PF_INET protocol family [ 0.117775] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.119237] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.119338] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.119364] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119463] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119694] TCP: Hash tables configured (established 8192 bind 8192) [ 0.119932] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.120025] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120065] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120293] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.120337] NET: Registered PF_XDP protocol family [ 0.120349] PCI: CLS 0 bytes, default 64 [ 0.120852] Trying to unpack rootfs image as initramfs... [ 0.121214] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.122483] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.194214] Initialise system trusted keyrings [ 0.194332] Key type blacklist registered [ 0.195570] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.203497] zbud: loaded [ 0.204657] integrity: Platform Keyring initialized [ 0.204692] integrity: Machine keyring initialized [ 0.204701] Key type asymmetric registered [ 0.204709] Asymmetric key parser 'x509' registered [ 1.422623] Freeing initrd memory: 25132K [ 1.444577] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.444841] bounce: pool size: 64 pages [ 1.445027] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.445195] io scheduler mq-deadline registered [ 1.450375] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.471309] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.471321] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473603] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473612] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.474450] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474459] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.475301] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.475310] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.477623] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.480467] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.483232] Serial: AMBA driver [ 1.483456] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.483933] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.484400] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.565120] printk: console [ttySAC2] enabled [ 2.569955] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.580580] STM32 USART driver initialized [ 2.594988] mousedev: PS/2 mouse device common for all mice [ 2.626284] s5m-rtc s5m-rtc: registered as rtc0 [ 2.634882] s5m-rtc s5m-rtc: setting system clock to 2024-09-26T06:14:11 UTC (1727331251) [ 2.644732] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.652195] ledtrig-cpu: registered to indicate activity on CPUs [ 2.660217] NET: Registered PF_INET6 protocol family [ 2.684222] Segment Routing with IPv6 [ 2.686526] In-situ OAM (IOAM) with IPv6 [ 2.690422] mip6: Mobile IPv6 [ 2.693286] NET: Registered PF_PACKET protocol family [ 2.698474] mpls_gso: MPLS GSO support [ 2.702526] ThumbEE CPU extension supported. [ 2.706320] Registering SWP/SWPB emulation handler [ 2.711576] registered taskstats version 1 [ 2.715195] Loading compiled-in X.509 certificates [ 3.175719] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.183075] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.194145] zswap: loaded using pool lzo/zbud [ 3.198044] Key type .fscrypt registered [ 3.201390] Key type fscrypt-provisioning registered [ 3.225630] Key type encrypted registered [ 3.228228] AppArmor: AppArmor sha1 policy hashing enabled [ 3.233713] ima: No TPM chip found, activating TPM-bypass! [ 3.239161] ima: Allocated hash algorithm: sha256 [ 3.243844] ima: No architecture policies found [ 3.248428] evm: Initialising EVM extended attributes: [ 3.253450] evm: security.selinux [ 3.256751] evm: security.SMACK64 (disabled) [ 3.260995] evm: security.SMACK64EXEC (disabled) [ 3.265598] evm: security.SMACK64TRANSMUTE (disabled) [ 3.270633] evm: security.SMACK64MMAP (disabled) [ 3.275230] evm: security.apparmor [ 3.278614] evm: security.ima [ 3.281550] evm: security.capability [ 3.285132] evm: HMAC attrs: 0x1 [ 3.871510] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.877455] clk: Disabling unused clocks [ 3.890366] Freeing unused kernel image (initmem) memory: 2048K [ 3.895244] Checked W+X mappings: passed, no W+X pages found [ 3.900481] Run /init as init process [ 3.904116] with arguments: [ 3.904123] /init [ 3.904130] with environment: [ 3.904136] HOME=/ [ 3.904141] TERM=linux [ 4.793171] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.813321] usbcore: registered new interface driver usbfs [ 4.817472] usbcore: registered new interface driver hub [ 4.817992] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.836743] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.853286] Synopsys Designware Multimedia Card Interface Driver [ 4.878861] usbcore: registered new device driver usb [ 4.893771] SCSI subsystem initialized [ 4.899808] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 4.923082] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.923238] phy phy-12130000.phy.2: phy_power_on was called before phy_init [ 4.929029] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.942622] s2mps11-clk s5m8767-clk: DMA mask not set [ 4.959299] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.964326] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.980743] exynos-ehci 12110000.usb: EHCI Host Controller [ 4.992195] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.997217] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 5.002739] libata version 3.00 loaded. [ 5.010698] exynos-ohci 12120000.usb: USB Host Controller [ 5.013618] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1 [ 5.022305] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2 [ 5.030433] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.039617] exynos-ohci 12120000.usb: irq 107, io mem 0x12120000 [ 5.047054] exynos-ehci 12110000.usb: irq 107, io mem 0x12110000 [ 5.072944] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.074360] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109,32 bit host data width,128 deep fifo [ 5.077893] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.089854] mmc_host mmc0: card is polling. [ 5.095261] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.106624] usb usb1: Product: EHCI Host Controller [ 5.111456] usb usb1: Manufacturer: Linux 6.1.0-25-armmp-lpae ehci_hcd [ 5.117968] usb usb1: SerialNumber: 12110000.usb [ 5.136513] hub 1-0:1.0: USB hub found [ 5.138895] hub 1-0:1.0: 3 ports detected [ 5.145298] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.152164] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.159322] usb usb2: Product: USB Host Controller [ 5.164093] usb usb2: Manufacturer: Linux 6.1.0-25-armmp-lpae ohci_hcd [ 5.170603] usb usb2: SerialNumber: 12120000.usb [ 5.177559] hub 2-0:1.0: USB hub found [ 5.181073] hub 2-0:1.0: 3 ports detected [ 5.182737] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.193447] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.225892] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.239254] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.251259] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.265260] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.270911] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.279717] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.292458] scsi host0: ahci-dwc [ 5.294753] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.324379] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.334829] mmc0: new DDR MMC card at address 0001 [ 5.341975] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.352559] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.361967] mmc1: new high speed SDHC card at address aaaa [ 5.368602] mmcblk0: p1 p2 p3 p4 [ 5.375717] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.382098] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.386932] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.397730] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.621259] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.695508] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.790302] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.795922] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.801722] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.803980] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.818371] ata1.00: configured for UDMA/133 [ 5.822206] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 5.875886] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.880068] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 5.888128] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 5.897003] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 5.903145] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 5.908410] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 5.916085] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 5.922553] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 5.932224] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.940113] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.947285] usb usb3: Product: xHCI Host Controller [ 5.952159] usb usb3: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 5.958650] usb usb3: SerialNumber: xhci-hcd.2.auto [ 5.965390] hub 3-0:1.0: USB hub found [ 5.967792] hub 3-0:1.0: 1 port detected [ 5.973941] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.980825] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 5.988862] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.996050] usb usb4: Product: xHCI Host Controller [ 6.000902] usb usb4: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.007423] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.014642] hub 4-0:1.0: USB hub found [ 6.017056] hub 4-0:1.0: 1 port detected [ 6.022677] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.032398] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.038463] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.054405] sd 0:0:0:0: [sda] Write Protect is off [ 6.057753] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.058435] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.070617] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.092278] sda: sda1 sda2 < sda5 > [ 6.095139] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.130645] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.239102] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.347099] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.455060] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.563055] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 6.971545] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.079152] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 7.158282] random: crng init done [ 7.267438] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.278369] device-mapper: uevent: version 1.0.3 [ 7.282989] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 7.687247] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 11.003599] PM: Image not found (code -22) [ 11.515430] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.721383] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.047922] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.440759] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.450696] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.607809] panfrost 11800000.gpu: clock rate = 533000000 [ 15.615863] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.641185] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 15.647542] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 15.655644] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 15.667348] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 15.770306] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 15.780370] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 15.839880] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 15.886295] usb3503 usb-hub: switched to HUB mode [ 15.889539] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.948714] blk_print_req_error: 6 callbacks suppressed [ 15.948724] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.062053] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.170178] I/O error, dev mmcblk1, sector 7744450 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.222518] usb 1-3: new high-speed USB device number 2 using exynos-ehci [ 16.278327] I/O error, dev mmcblk1, sector 7744451 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.386580] I/O error, dev mmcblk1, sector 7744452 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.396129] usb 1-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.402965] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.432442] hub 1-3:1.0: USB hub found [ 16.435107] hub 1-3:1.0: 3 ports detected [ 16.487478] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.494775] I/O error, dev mmcblk1, sector 7744453 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.602847] I/O error, dev mmcblk1, sector 7744454 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.711010] I/O error, dev mmcblk1, sector 7744455 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 16.734500] usb 1-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.856922] usb 1-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 16.864207] usb 1-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 16.871360] usb 1-3.2: Product: USB2.0 Hub [ 16.882131] hub 1-3.2:1.0: USB hub found [ 16.885865] hub 1-3.2:1.0: 4 ports detected [ 17.127418] I/O error, dev mmcblk1, sector 7744448 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.198317] usb 1-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.235266] I/O error, dev mmcblk1, sector 7744449 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 17.313085] usb 1-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.320550] usb 1-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.327978] usb 1-3.2.4: Product: AX88772 [ 17.331887] usb 1-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.337046] usb 1-3.2.4: SerialNumber: 000001 [ 17.819124] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 17.846043] Buffer I/O error on dev mmcblk1, logical block 968056, async page read [ 18.505021] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.520567] Asix Electronics AX88772A usb-001:004:10: attached PHY driver (mii_bus:phy_addr=usb-001:004:10, irq=POLL) [ 18.532358] asix 1-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, ca:5f:16:79:63:c9 [ 18.550618] usbcore: registered new interface driver asix [ 19.392625] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.750609] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.832467] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 22.046081] Adding 1949692k swap on /dev/mapper/arndale--westfield--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 23.247971] audit: type=1400 audit(1727331271.576:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=905 comm="apparmor_parser" [ 23.263233] audit: type=1400 audit(1727331271.576:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=904 comm="apparmor_parser" [ 23.276816] audit: type=1400 audit(1727331271.588:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=905 comm="apparmor_parser" [ 23.317311] asix 1-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.620112] audit: type=1400 audit(1727331271.948:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=943 comm="apparmor_parser" [ 23.639578] audit: type=1400 audit(1727331271.964:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=943 comm="apparmor_parser" [ 23.653010] audit: type=1400 audit(1727331271.964:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=943 comm="apparmor_parser" [ 23.980142] audit: type=1400 audit(1727331272.308:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=941 comm="apparmor_parser" [ 24.006323] audit: type=1400 audit(1727331272.328:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=941 comm="apparmor_parser" [ 24.022214] audit: type=1400 audit(1727331272.332:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/ntpd" pid=947 comm="apparmor_parser" [ 24.037454] audit: type=1400 audit(1727331272.332:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=941 comm="apparmor_parser" [ 25.479725] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.479840] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.639096] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.646680] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.653643] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.660691] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.670355] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.680701] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.701785] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.711721] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.717099] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.726455] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1