[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.0-25-armmp-lpae (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Debian 6.1.106-3 (2024-08-26) [ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Insignal Arndale evaluation board based on Exynos5250 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 16 MiB at 0x00000000bf000000 [ 0.000000] Samsung CPU ID: 0x43520010 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 18 pages/cpu s44820 r8192 d20716 u73728 [ 0.000000] pcpu-alloc: s44820 r8192 d20716 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: ro root=/dev/mapper/arndale--lakeside--vg-root rootdelay=3 console=ttySAC2,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.000000] Memory: 2015504K/2097152K available (12288K kernel code, 1717K rwdata, 3748K rodata, 2048K init, 383K bss, 65264K reserved, 16384K cma-reserved, 1294332K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 39996 entries in 118 pages [ 0.000000] ftrace: allocated 118 pages with 5 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Exynos5250: clock setup completed, armclk=1000000000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000001] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000018] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 [ 0.002619] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.002633] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.002649] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.002660] Ignoring duplicate/late registration of read_current_timer delay [ 0.003027] Console: colour dummy device 80x30 [ 0.003068] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.003082] CPU: Testing write buffer coherency: ok [ 0.003124] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.003132] CPU0: Spectre BHB: enabling loop workaround for all CPUs [ 0.003138] pid_max: default: 32768 minimum: 301 [ 0.003506] LSM: Security Framework initializing [ 0.003579] landlock: Up and running. [ 0.003583] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.003770] AppArmor: AppArmor initialized [ 0.003783] TOMOYO Linux initialized [ 0.003827] LSM support for eBPF active [ 0.004075] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004089] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005501] /cpus/cpu@0 missing clock-frequency property [ 0.005527] /cpus/cpu@1 missing clock-frequency property [ 0.005540] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006479] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006486] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006587] cblist_init_generic: Setting adjustable number of callback queues. [ 0.006592] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.006732] Setting up static identity map for 0x40400000 - 0x404000ac [ 0.007893] rcu: Hierarchical SRCU implementation. [ 0.007899] rcu: Max phase no-delay instances is 1000. [ 0.010020] EFI services will not be available. [ 0.010361] smp: Bringing up secondary CPUs ... [ 0.011099] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011111] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable [ 0.011240] smp: Brought up 1 node, 2 CPUs [ 0.011249] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.011256] CPU: All CPU(s) started in HYP mode. [ 0.011260] CPU: Virtualization extensions available. [ 0.012113] devtmpfs: initialized [ 0.023183] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.023416] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023440] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.024000] pinctrl core: initialized pinctrl subsystem [ 0.024727] DMI not present or invalid. [ 0.025405] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.026948] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.028481] audit: initializing netlink subsys (disabled) [ 0.028683] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 [ 0.029861] thermal_sys: Registered thermal governor 'fair_share' [ 0.029868] thermal_sys: Registered thermal governor 'bang_bang' [ 0.029872] thermal_sys: Registered thermal governor 'step_wise' [ 0.029878] thermal_sys: Registered thermal governor 'user_space' [ 0.029882] thermal_sys: Registered thermal governor 'power_allocator' [ 0.030083] No ATAGs? [ 0.030150] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.030158] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.031241] Serial: AMBA PL011 UART driver [ 0.080660] platform panel: Fixed dependency cycle(s) with /soc/dsi@14500000/bridge@0 [ 0.087632] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.091711] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.091719] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.099367] iommu: Default domain type: Translated [ 0.099375] iommu: DMA domain TLB invalidation policy: strict mode [ 0.100340] i2c-gpio soc:i2c-10: using lines 6 (SDA) and 7 (SCL) [ 0.100847] s3c-i2c 12c60000.i2c: slave address 0x66 [ 0.100858] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz [ 0.101372] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK8 [ 0.101402] i2c 0-0066: Fixed dependency cycle(s) with /soc/i2c@12c60000/pmic@66/regulators/BUCK7 [ 0.101646] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter [ 0.102140] s3c-i2c 12c90000.i2c: slave address 0x00 [ 0.102151] s3c-i2c 12c90000.i2c: bus frequency set to 65 KHz [ 0.102525] s3c-i2c 12c90000.i2c: i2c-3: S3C I2C adapter [ 0.102820] s3c-i2c 12ce0000.i2c: slave address 0x00 [ 0.102829] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz [ 0.103156] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter [ 0.103267] s3c-i2c 121d0000.i2c: slave address 0x00 [ 0.103276] s3c-i2c 121d0000.i2c: bus frequency set to 39 KHz [ 0.103460] s3c-i2c 121d0000.i2c: i2c-9: S3C I2C adapter [ 0.103676] pps_core: LinuxPPS API ver. 1 registered [ 0.103681] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.103698] PTP clock support registered [ 0.105198] NetLabel: Initializing [ 0.105204] NetLabel: domain hash size = 128 [ 0.105210] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.105264] NetLabel: unlabeled traffic allowed by default [ 0.105435] vgaarb: loaded [ 0.106380] clocksource: Switched to clocksource mct-frc [ 0.106964] VFS: Disk quotas dquot_6.6.0 [ 0.107048] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.107865] AppArmor: AppArmor Filesystem Enabled [ 0.117702] NET: Registered PF_INET protocol family [ 0.117906] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.119385] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.119485] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.119511] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.119611] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.119842] TCP: Hash tables configured (established 8192 bind 8192) [ 0.120075] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.120166] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120206] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.120438] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.120473] NET: Registered PF_XDP protocol family [ 0.120484] PCI: CLS 0 bytes, default 64 [ 0.121006] Trying to unpack rootfs image as initramfs... [ 0.121345] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 0.122630] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.194633] Initialise system trusted keyrings [ 0.194713] Key type blacklist registered [ 0.195939] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.203918] zbud: loaded [ 0.205134] integrity: Platform Keyring initialized [ 0.205179] integrity: Machine keyring initialized [ 0.205188] Key type asymmetric registered [ 0.205196] Asymmetric key parser 'x509' registered [ 1.422480] Freeing initrd memory: 25132K [ 1.444536] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.444807] bounce: pool size: 64 pages [ 1.444994] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.445163] io scheduler mq-deadline registered [ 1.450299] samsung-pinctrl 11400000.pinctrl: Failed to create device link (0x180) with soc [ 1.471422] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.471434] dma-pl330 121a0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.473719] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.473729] dma-pl330 121b0000.dma-controller: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 1.474582] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.474591] dma-pl330 10800000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.475413] dma-pl330 11c10000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 1.475422] dma-pl330 11c10000.dma-controller: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 1.477737] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5250] PRO_ID[0x43520000] REV[0x10] Detected [ 1.480613] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.483387] Serial: AMBA driver [ 1.483613] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 94, base_baud = 0) is a S3C6400/10 [ 1.484091] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 95, base_baud = 0) is a S3C6400/10 [ 1.484559] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 96, base_baud = 0) is a S3C6400/10 [ 2.565196] printk: console [ttySAC2] enabled [ 2.570034] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 97, base_baud = 0) is a S3C6400/10 [ 2.580651] STM32 USART driver initialized [ 2.595084] mousedev: PS/2 mouse device common for all mice [ 2.626400] s5m-rtc s5m-rtc: registered as rtc0 [ 2.635002] s5m-rtc s5m-rtc: setting system clock to 2024-09-30T19:54:34 UTC (1727726074) [ 2.644851] exynos-tmu 10060000.tmu: Regulator node (vtmu) not found [ 2.652317] ledtrig-cpu: registered to indicate activity on CPUs [ 2.660328] NET: Registered PF_INET6 protocol family [ 2.684260] Segment Routing with IPv6 [ 2.686551] In-situ OAM (IOAM) with IPv6 [ 2.690470] mip6: Mobile IPv6 [ 2.693321] NET: Registered PF_PACKET protocol family [ 2.698510] mpls_gso: MPLS GSO support [ 2.702530] ThumbEE CPU extension supported. [ 2.706332] Registering SWP/SWPB emulation handler [ 2.711621] registered taskstats version 1 [ 2.715223] Loading compiled-in X.509 certificates [ 3.175885] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 3.183228] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f' [ 3.194312] zswap: loaded using pool lzo/zbud [ 3.198191] Key type .fscrypt registered [ 3.201560] Key type fscrypt-provisioning registered [ 3.225853] Key type encrypted registered [ 3.228453] AppArmor: AppArmor sha1 policy hashing enabled [ 3.233938] ima: No TPM chip found, activating TPM-bypass! [ 3.239384] ima: Allocated hash algorithm: sha256 [ 3.244068] ima: No architecture policies found [ 3.248649] evm: Initialising EVM extended attributes: [ 3.253672] evm: security.selinux [ 3.256973] evm: security.SMACK64 (disabled) [ 3.261217] evm: security.SMACK64EXEC (disabled) [ 3.265820] evm: security.SMACK64TRANSMUTE (disabled) [ 3.270856] evm: security.SMACK64MMAP (disabled) [ 3.275454] evm: security.apparmor [ 3.278838] evm: security.ima [ 3.281773] evm: security.capability [ 3.285355] evm: HMAC attrs: 0x1 [ 3.871895] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.877855] clk: Disabling unused clocks [ 3.890749] Freeing unused kernel image (initmem) memory: 2048K [ 3.895612] Checked W+X mappings: passed, no W+X pages found [ 3.900870] Run /init as init process [ 3.904506] with arguments: [ 3.904513] /init [ 3.904519] with environment: [ 3.904524] HOME=/ [ 3.904530] TERM=linux [ 4.852689] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator [ 4.872986] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator [ 4.880107] Synopsys Designware Multimedia Card Interface Driver [ 4.897226] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator [ 4.898962] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 4.904687] usbcore: registered new interface driver usbfs [ 4.911924] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 4.917725] usbcore: registered new interface driver hub [ 4.931312] usbcore: registered new device driver usb [ 4.964525] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 4.969557] dwmmc_exynos 12200000.mmc: Version ID is 241a [ 4.975025] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 4.975977] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107,32 bit host data width,128 deep fifo [ 4.981355] dwmmc_exynos 12220000.mmc: Version ID is 241a [ 4.998477] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 108,32 bit host data width,128 deep fifo [ 5.006064] mmc_host mmc0: card is polling. [ 5.022936] s2mps11-clk s5m8767-clk: DMA mask not set [ 5.042469] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.051715] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 5.128743] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 5.134600] phy phy-12130000.phy.4: phy_power_on was called before phy_init [ 5.149086] SCSI subsystem initialized [ 5.165576] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 5.174024] exynos-ohci 12120000.usb: USB Host Controller [ 5.174504] exynos-ehci 12110000.usb: EHCI Host Controller [ 5.186643] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 5.201102] mmc0: new DDR MMC card at address 0001 [ 5.214214] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 5.225688] mmcblk0: mmc0:0001 M4G1FB 3.64 GiB [ 5.231235] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 5.232044] mmc1: new high speed SDHC card at address aaaa [ 5.246037] exynos-ohci 12120000.usb: irq 109, io mem 0x12120000 [ 5.255764] libata version 3.00 loaded. [ 5.259760] exynos-ehci 12110000.usb: irq 109, io mem 0x12110000 [ 5.265278] mmcblk0: p1 p2 p3 p4 [ 5.270883] ahci-dwc 122f0000.sata: supply ahci not found, using dummy regulator [ 5.276303] mmcblk0boot0: mmc0:0001 M4G1FB 1.00 MiB [ 5.282450] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 5.292347] mmcblk1: mmc1:aaaa SU04G 3.69 GiB [ 5.292403] ahci-dwc 122f0000.sata: supply phy not found, using dummy regulator [ 5.298462] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 5.310918] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.318083] usb usb2: Product: EHCI Host Controller [ 5.322956] usb usb2: Manufacturer: Linux 6.1.0-25-armmp-lpae ehci_hcd [ 5.329450] usb usb2: SerialNumber: 12110000.usb [ 5.336152] hub 2-0:1.0: USB hub found [ 5.338876] hub 2-0:1.0: 3 ports detected [ 5.348677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01 [ 5.352397] mmcblk0boot1: mmc0:0001 M4G1FB 1.00 MiB [ 5.355538] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.367671] usb usb1: Product: USB Host Controller [ 5.372434] usb usb1: Manufacturer: Linux 6.1.0-25-armmp-lpae ohci_hcd [ 5.375246] ahci-dwc 122f0000.sata: supply target not found, using dummy regulator [ 5.378945] usb usb1: SerialNumber: 12120000.usb [ 5.394031] hub 1-0:1.0: USB hub found [ 5.396385] hub 1-0:1.0: 3 ports detected [ 5.413672] mmcblk0rpmb: mmc0:0001 M4G1FB 128 KiB, chardev (241:0) [ 5.424696] ahci-dwc 122f0000.sata: SSS flag set, parallel bus scan disabled [ 5.430336] ahci-dwc 122f0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.439155] ahci-dwc 122f0000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 5.450092] scsi host0: ahci-dwc [ 5.452366] ata1: SATA max UDMA/133 mmio [mem 0x122f0000-0x122f01fe] port 0x100 irq 110 [ 5.942454] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.948039] ata1.00: ATA-8: HGST HTS545050A7E380, GG2OAC90, max UDMA/133 [ 5.953879] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 5.961328] ata1.00: configured for UDMA/133 [ 5.965093] scsi 0:0:0:0: Direct-Access ATA HGST HTS545050A7 AC90 PQ: 0 ANSI: 5 [ 6.022689] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.026826] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 6.034920] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000008002010010 [ 6.043788] xhci-hcd xhci-hcd.2.auto: irq 111, io mem 0x12000000 [ 6.050258] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 6.055228] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 6.062841] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 6.069499] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01 [ 6.077595] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.084796] usb usb3: Product: xHCI Host Controller [ 6.089657] usb usb3: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.096160] usb usb3: SerialNumber: xhci-hcd.2.auto [ 6.101619] hub 3-0:1.0: USB hub found [ 6.104800] hub 3-0:1.0: 1 port detected [ 6.109212] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.116905] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01 [ 6.124998] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.132216] usb usb4: Product: xHCI Host Controller [ 6.137051] usb usb4: Manufacturer: Linux 6.1.0-25-armmp-lpae xhci-hcd [ 6.143554] usb usb4: SerialNumber: xhci-hcd.2.auto [ 6.149642] hub 4-0:1.0: USB hub found [ 6.152212] hub 4-0:1.0: 1 port detected [ 6.202710] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 6.208761] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.214100] sd 0:0:0:0: [sda] Write Protect is off [ 6.218738] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.218818] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.232014] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.254296] sda: sda1 sda2 < sda5 > [ 6.257039] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.358404] random: crng init done [ 7.467510] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 7.478362] device-mapper: uevent: version 1.0.3 [ 7.483088] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 11.282983] PM: Image not found (code -22) [ 11.701971] EXT4-fs (dm-0): mounting ext3 file system using the ext4 subsystem [ 11.858197] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none. [ 12.169266] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist. [ 15.578188] exynos-trng 10830600.rng: Exynos True Random Number Generator. [ 15.599155] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 15.733227] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 15.966446] usb3503 usb-hub: switched to HUB mode [ 15.969692] usb3503 usb-hub: usb3503_probe: probed in hub mode [ 15.979294] panfrost 11800000.gpu: clock rate = 533000000 [ 16.063529] panfrost 11800000.gpu: mali-t600 id 0x600 major 0x0 minor 0x0 status 0x1 [ 16.069904] panfrost 11800000.gpu: features: 00000000,00000408, issues: 00000000,31b4dfff [ 16.078016] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 [ 16.089734] panfrost 11800000.gpu: shader_present=0xf l2_present=0x1 [ 16.099452] [drm] Initialized panfrost 1.2.0 20180908 for 11800000.gpu on minor 0 [ 16.294556] usb 2-3: new high-speed USB device number 2 using exynos-ehci [ 16.459495] usb 2-3: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 16.466510] usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 16.499648] hub 2-3:1.0: USB hub found [ 16.505411] hub 2-3:1.0: 3 ports detected [ 16.759611] OF: graph: no port node found in /soc/hdmi@14530000 [ 16.794464] usb 2-3.2: new high-speed USB device number 3 using exynos-ehci [ 16.915999] usb 2-3.2: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=77.32 [ 16.922981] usb 2-3.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 16.930420] usb 2-3.2: Product: USB2.0 Hub [ 16.948246] hub 2-3.2:1.0: USB hub found [ 16.951332] hub 2-3.2:1.0: 4 ports detected [ 17.246424] usb 2-3.2.4: new high-speed USB device number 4 using exynos-ehci [ 17.364856] usb 2-3.2.4: New USB device found, idVendor=0b95, idProduct=772a, bcdDevice= 0.01 [ 17.372439] usb 2-3.2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.379568] usb 2-3.2.4: Product: AX88772 [ 17.383650] usb 2-3.2.4: Manufacturer: ASIX Elec. Corp. [ 17.388836] usb 2-3.2.4: SerialNumber: 000001 [ 17.827753] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random [ 18.517089] asix 2-3.2.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-002:004:10] driver [Asix Electronics AX88772A] (irq=POLL) [ 18.532873] Asix Electronics AX88772A usb-002:004:10: attached PHY driver (mii_bus:phy_addr=usb-002:004:10, irq=POLL) [ 18.544731] asix 2-3.2.4:1.0 eth0: register 'asix' at usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, f2:20:7e:45:e1:eb [ 18.560563] usbcore: registered new interface driver asix [ 19.352108] EXT4-fs (dm-0): re-mounted. Quota mode: none. [ 21.106244] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.169418] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 21.379654] Adding 1949692k swap on /dev/mapper/arndale--lakeside--vg-swap_1. Priority:-2 extents:1 across:1949692k FS [ 22.604713] audit: type=1400 audit(1727726094.304:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=894 comm="apparmor_parser" [ 22.625269] audit: type=1400 audit(1727726094.320:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=894 comm="apparmor_parser" [ 22.640106] audit: type=1400 audit(1727726094.332:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=893 comm="apparmor_parser" [ 22.834615] asix 2-3.2.4:1.0 eth0: configuring for phy/internal link mode [ 23.004127] audit: type=1400 audit(1727726094.704:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=931 comm="apparmor_parser" [ 23.023364] audit: type=1400 audit(1727726094.720:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=931 comm="apparmor_parser" [ 23.036784] audit: type=1400 audit(1727726094.720:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=931 comm="apparmor_parser" [ 23.341397] audit: type=1400 audit(1727726095.040:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=929 comm="apparmor_parser" [ 23.358021] audit: type=1400 audit(1727726095.044:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=929 comm="apparmor_parser" [ 23.375145] audit: type=1400 audit(1727726095.048:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=929 comm="apparmor_parser" [ 23.392662] audit: type=1400 audit(1727726095.056:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=929 comm="apparmor_parser" [ 25.000410] asix 2-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow control off [ 25.000521] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 28.641684] exynos4-fb 14400000.fimd: deferred probe timeout, ignoring dependency [ 28.653399] exynos-mixer 14450000.mixer: deferred probe timeout, ignoring dependency [ 28.661114] [drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations [ 28.667500] exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm]) [ 28.675956] exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm]) [ 28.685467] exynos-drm exynos-drm: bound 14500000.dsi (ops hdmi_enable [exynosdrm]) [ 28.692316] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm]) [ 28.701427] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.707885] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes [ 28.718762] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1